If a CPU doesn't support the page size for which the kernel is
configured, then we will complain and refuse to bring it online. For
secondary CPUs (and the boot CPU on a system booting with EFI), we will
also print an error identifying the mismatch.
Consequently, the only time that the cpufeature code can detect a
granule size mismatch is for a granule other than the one that is
currently being used. Although we would rather such systems didn't
exist, we've unfortunately lost that battle and Kevin reports that
on his amlogic S922X (odroid-n2 board) we end up warning and taining
with defconfig because 16k pages are not supported by all of the CPUs.
In such a situation, we don't actually care about the feature mismatch,
particularly now that KVM only exposes the sanitised view of the CPU
registers (commit 93390c0a1b - "arm64: KVM: Hide unsupported AArch64
CPU features from guests"). Treat the granule fields as non-strict and
let Kevin run without a tainted kernel.
Cc: Marc Zyngier <maz@kernel.org>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
[catalin.marinas@arm.com: changelog updated with KVM sanitised regs commit]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
It's large and doesn't need contiguous memory. Fixes
allocation failures in some cases.
v2: kvfree the memory.
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The SOC15_REG_OFFSET() macro wasn't used, making the soft recovery fail.
v2: use WREG32_SOC15 instead of WREG32 + SOC15_REG_OFFSET
Signed-off-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
fec's gpio phy reset properties have been deprecated.
Update the dt-bindings documentation to explicitly mark
them as such, and provide a short description of the
recommended alternative.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return or break from the middle of the loop, there is no
put, thus causing a memory leak. Hence add an of_node_put before the
return or break in three places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
ITLB entry modifications must be followed by the isync instruction
before the new entries are possibly used. cpu_reset lacks one isync
between ITLB way 6 initialization and jump to the identity mapping.
Add missing isync to xtensa cpu_reset.
Cc: stable@vger.kernel.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
* adf4371
- Calculation of the value to program to control the output frequency
was incorrect.
* max9611
- Fix temperature reading in probe. A recent fix for a wrong mask
meant this code was looked at afresh. A second bug became obvious
in which the return value was used inplace of the desired register
value. This had no visible effect other than a communication test
not actually testing the communications.
-----BEGIN PGP SIGNATURE-----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=bhXg
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fix for the 5.3 cycle.
* adf4371
- Calculation of the value to program to control the output frequency
was incorrect.
* max9611
- Fix temperature reading in probe. A recent fix for a wrong mask
meant this code was looked at afresh. A second bug became obvious
in which the return value was used inplace of the desired register
value. This had no visible effect other than a communication test
not actually testing the communications.
* tag 'iio-fixes-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: max9611: Fix temperature reading in probe
iio: frequency: adf4371: Fix output frequency setting
The syzbot fuzzer has found two (!) races in the USB character device
registration and deregistration routines. This patch fixes the races.
The first race results from the fact that usb_deregister_dev() sets
usb_minors[intf->minor] to NULL before calling device_destroy() on the
class device. This leaves a window during which another thread can
allocate the same minor number but will encounter a duplicate name
error when it tries to register its own class device. A typical error
message in the system log would look like:
sysfs: cannot create duplicate filename '/class/usbmisc/ldusb0'
The patch fixes this race by destroying the class device first.
The second race is in usb_register_dev(). When that routine runs, it
first allocates a minor number, then drops minor_rwsem, and then
creates the class device. If the device creation fails, the minor
number is deallocated and the whole routine returns an error. But
during the time while minor_rwsem was dropped, there is a window in
which the minor number is allocated and so another thread can
successfully open the device file. Typically this results in
use-after-free errors or invalid accesses when the other thread closes
its open file reference, because the kernel then tries to release
resources that were already deallocated when usb_register_dev()
failed. The patch fixes this race by keeping minor_rwsem locked
throughout the entire routine.
Reported-and-tested-by: syzbot+30cf45ebfe0b0c4847a1@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1908121607590.1659-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
/home/tglx/work/kernel/linus/linux/arch/x86/math-emu/errors.c: In function ‘FPU_printall’:
/home/tglx/work/kernel/linus/linux/arch/x86/math-emu/errors.c:187:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
tagi = FPU_Special(r);
~~~~~^~~~~~~~~~~~~~~~
/home/tglx/work/kernel/linus/linux/arch/x86/math-emu/errors.c:188:3: note: here
case TAG_Valid:
^~~~
/home/tglx/work/kernel/linus/linux/arch/x86/math-emu/fpu_trig.c: In function ‘fyl2xp1’:
/home/tglx/work/kernel/linus/linux/arch/x86/math-emu/fpu_trig.c:1353:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (denormal_operand() < 0)
^
/home/tglx/work/kernel/linus/linux/arch/x86/math-emu/fpu_trig.c:1356:3: note: here
case TAG_Zero:
Remove the pointless 'break;' after 'continue;' while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix
arch/x86/kernel/apic/probe_32.c: In function ‘default_setup_apic_routing’:
arch/x86/kernel/apic/probe_32.c:146:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!APIC_XAPIC(version)) {
^
arch/x86/kernel/apic/probe_32.c:151:3: note: here
case X86_VENDOR_HYGON:
^~~~
for 32-bit builds.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190811154036.29805-1-bp@alien8.de
Zorro Lang reported a crash in generic/475 if we try to inactivate a
corrupt inode with a NULL attr fork (stack trace shortened somewhat):
RIP: 0010:xfs_bmapi_read+0x311/0xb00 [xfs]
RSP: 0018:ffff888047f9ed68 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff888047f9f038 RCX: 1ffffffff5f99f51
RDX: 0000000000000002 RSI: 0000000000000008 RDI: 0000000000000012
RBP: ffff888002a41f00 R08: ffffed10005483f0 R09: ffffed10005483ef
R10: ffffed10005483ef R11: ffff888002a41f7f R12: 0000000000000004
R13: ffffe8fff53b5768 R14: 0000000000000005 R15: 0000000000000001
FS: 00007f11d44b5b80(0000) GS:ffff888114200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000ef6000 CR3: 000000002e176003 CR4: 00000000001606e0
Call Trace:
xfs_dabuf_map.constprop.18+0x696/0xe50 [xfs]
xfs_da_read_buf+0xf5/0x2c0 [xfs]
xfs_da3_node_read+0x1d/0x230 [xfs]
xfs_attr_inactive+0x3cc/0x5e0 [xfs]
xfs_inactive+0x4c8/0x5b0 [xfs]
xfs_fs_destroy_inode+0x31b/0x8e0 [xfs]
destroy_inode+0xbc/0x190
xfs_bulkstat_one_int+0xa8c/0x1200 [xfs]
xfs_bulkstat_one+0x16/0x20 [xfs]
xfs_bulkstat+0x6fa/0xf20 [xfs]
xfs_ioc_bulkstat+0x182/0x2b0 [xfs]
xfs_file_ioctl+0xee0/0x12a0 [xfs]
do_vfs_ioctl+0x193/0x1000
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x6f/0xb0
do_syscall_64+0x9f/0x4d0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f11d39a3e5b
The "obvious" cause is that the attr ifork is null despite the inode
claiming an attr fork having at least one extent, but it's not so
obvious why we ended up with an inode in that state.
Reported-by: Zorro Lang <zlang@redhat.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204031
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Continue our game of replacing ASSERTs for corrupt ondisk metadata with
EFSCORRUPTED returns.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
We need to set the error codes on these paths. Currently the only
possible error code is -EMSGSIZE so that's what the patch uses.
Fixes: 83c2c1fcbd ("RDMA/nldev: Allow get counter mode through RDMA netlink")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190809101311.GA17867@mwanda
Signed-off-by: Doug Ledford <dledford@redhat.com>
The error handling code doesn't free siw_cpu_info.tx_valid_cpus[0]. The
first iteration through the loop is a no-op so this is sort of an off
by one bug. Also Bernard pointed out that we can remove the NULL
assignment and simplify the code a bit.
Fixes: bdcf26bf9b ("rdma/siw: network and RDMA core interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bernard Metzler <bmt@zurich.ibm.com>
Reviewed-by: Bernard Metzler <bmt@zurich.ibm.com>
Link: https://lore.kernel.org/r/20190809140904.GB3552@mwanda
Signed-off-by: Doug Ledford <dledford@redhat.com>
Oded writes:
This tag contains a couple of important fixes:
- Four fixes when running on s390 architecture (BE). With these fixes, the
driver is fully functional on Big-endian architectures. The fixes
include:
- Validation/Patching of user packets
- Completion queue handling
- Internal H/W queues submission
- Device IRQ unmasking operation
- Fix to double free in an error path to avoid kernel corruption
- Fix to DRAM usage accounting when a user process is terminated
forcefully.
* tag 'misc-habanalabs-fixes-2019-08-12' of git://people.freedesktop.org/~gabbayo/linux:
habanalabs: fix device IRQ unmasking for BE host
habanalabs: fix endianness handling for internal QMAN submission
habanalabs: fix completion queue handling when host is BE
habanalabs: fix endianness handling for packets from user
habanalabs: fix DRAM usage accounting on context tear down
habanalabs: Avoid double free in error flow
`dt3k_ns_to_timer()` determines the prescaler and divisor to use to
produce a desired timing period. It is influenced by a rounding mode
and can round the divisor up, down, or to the nearest value. However,
the code for rounding up currently does the same as rounding down! Fix
ir by using the `DIV_ROUND_UP()` macro to calculate the divisor when
rounding up.
Also, change the types of the `divider`, `base` and `prescale` variables
from `int` to `unsigned int` to avoid mixing signed and unsigned types
in the calculations.
Also fix a typo in a nearby comment: "improvment" => "improvement".
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190812120814.21188-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In `dt3k_ns_to_timer()` the following lines near the end of the function
result in a signed integer overflow:
prescale = 15;
base = timer_base * (1 << prescale);
divider = 65535;
*nanosec = divider * base;
(`divider`, `base` and `prescale` are type `int`, `timer_base` and
`*nanosec` are type `unsigned int`. The value of `timer_base` will be
either 50 or 100.)
The main reason for the overflow is that the calculation for `base` is
completely wrong. It should be:
base = timer_base * (prescale + 1);
which matches an earlier instance of this calculation in the same
function.
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20190812111517.26803-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In read_per_ring_refs(), after 'req' and related memory regions are
allocated, xen_blkif_map() is invoked to map the shared frame, irq, and
etc. However, if this mapping process fails, no cleanup is performed,
leading to memory leaks. To fix this issue, invoke the cleanup before
returning the error.
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_exit_queue will free elevator_data, while blk_mq_requeue_work
will access it. Move cancel of requeue_work to the front of
blk_exit_queue to avoid use-after-free.
blk_exit_queue blk_mq_requeue_work
__elevator_exit blk_mq_run_hw_queues
blk_mq_exit_sched blk_mq_run_hw_queue
dd_exit_queue blk_mq_hctx_has_pending
kfree(elevator_data) blk_mq_sched_has_work
dd_has_work
Fixes: fbc2a15e34 ("blk-mq: move cancel of requeue_work into blk_mq_release")
Cc: stable@vger.kernel.org
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just a three fixes this time around.
A race condition on mass storage gadget between disable() and
set_alt()
Clear a flag that was left set upon reset or disconnect
A fix for renesas_usb3 UDC's sysfs interface
-----BEGIN PGP SIGNATURE-----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=QkbV
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.3-rc4
Just a three fixes this time around.
A race condition on mass storage gadget between disable() and
set_alt()
Clear a flag that was left set upon reset or disconnect
A fix for renesas_usb3 UDC's sysfs interface
* tag 'fixes-for-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: gadget: mass_storage: Fix races between fsg_disable and fsg_set_alt
usb: gadget: composite: Clear "suspended" on reset/disconnect
usb: gadget: udc: renesas_usb3: Fix sysfs interface of "role"
Currently, failure of cpuhp_setup_state() is ignored and the syscore ops
and the control interfaces can still be added even after the failure. But,
this error handling will cause a few issues:
1. The CPUs may have different values in the IA32_UMWAIT_CONTROL
MSR because there is no way to roll back the control MSR on
the CPUs which already set the MSR before the failure.
2. If the sysfs interface is added successfully, there will be a mismatch
between the global control value and the control MSR:
- The interface shows the default global control value. But,
the control MSR is not set to the value because the CPU online
function, which is supposed to set the MSR to the value,
is not installed.
- If the sysadmin changes the global control value through
the interface, the control MSR on all current online CPUs is
set to the new value. But, the control MSR on newly onlined CPUs
after the value change will not be set to the new value due to
lack of the CPU online function.
3. On resume from suspend/hibernation, the boot CPU restores the control
MSR to the global control value through the syscore ops. But, the
control MSR on all APs is not set due to lake of the CPU online
function.
To solve the issues and enforce consistent behavior on the failure
of the CPU hotplug setup, make the following changes:
1. Cache the original control MSR value which is configured by
hardware or BIOS before kernel boot. This value is likely to
be 0. But it could be a different number as well. Cache the
control MSR only once before the MSR is changed.
2. Add the CPU offline function so that the MSR is restored to the
original control value on all CPUs on the failure.
3. On the failure, exit from cpumait_init() so that the syscore ops
and the control interfaces are not added.
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1565401237-60936-1-git-send-email-fenghua.yu@intel.com
Fix get_efi_config_table using the wrong structs when booting a
64 bit kernel on 32 bit firmware.
Fixes: 82d736ac56 ("Abstract out support for locating an EFI config table")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-By: Matthew Garrett <mjg59@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
One of the modifications made by commit d916b1be94 ("nvme-pci: use
host managed power state for suspend") was adding a pci_save_state()
call to nvme_suspend() so as to instruct the PCI bus type to leave
devices handled by the nvme driver in D0 during suspend-to-idle.
That was done with the assumption that ASPM would transition the
device's PCIe link into a low-power state when the device became
inactive. However, if ASPM is disabled for the device, its PCIe
link will stay in L0 and in that case commit d916b1be94 is likely
to cause the energy used by the system while suspended to increase.
Namely, if the device in question works in accordance with the PCIe
specification, putting it into D3hot causes its PCIe link to go to
L1 or L2/L3 Ready, which is lower-power than L0. Since the energy
used by the system while suspended depends on the state of its PCIe
link (as a general rule, the lower-power the state of the link, the
less energy the system will use), putting the device into D3hot
during suspend-to-idle should be more energy-efficient that leaving
it in D0 with disabled ASPM.
For this reason, avoid leaving NVMe devices with disabled ASPM in D0
during suspend-to-idle. Instead, shut them down entirely and let
the PCI bus type put them into D3.
Fixes: d916b1be94 ("nvme-pci: use host managed power state for suspend")
Link: https://lore.kernel.org/linux-pm/2763495.NmdaWeg79L@kreacher/T/#t
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Add a function checking whether or not PCIe ASPM has been enabled for
a given device.
It will be used by the NVMe driver to decide how to handle the
device during system suspend.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
When unmasking IRQs inside the ASIC, the driver passes an array of all the
IRQ to unmask. The ASIC's CPU is working in LE so when running in a BE
host, the driver needs to do the proper endianness swapping when preparing
this array.
In addition, this patch also fixes the endianness of a couple of kernel log
debug messages that print values of packets
Signed-off-by: Ben Segal <bpsegal20@gmail.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The PQs of internal H/W queues (QMANs) can be located in different memory
areas for different ASICs. Therefore, when writing PQEs, we need to use
the correct function according to the location of the PQ. e.g. if the PQ
is located in the device's memory (SRAM or DRAM), we need to use
memcpy_toio() so it would work in architectures that have separate
address ranges for IO memory.
This patch makes the code that writes the PQE to be ASIC-specific so we
can handle this properly per ASIC.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Tested-by: Ben Segal <bpsegal20@gmail.com>
This patch fix the CQ irq handler to work in hosts with BE architecture.
It adds the correct endian-swapping macros around the relevant memory
accesses.
Signed-off-by: Ben Segal <bpsegal20@gmail.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Packets that arrive from the user and need to be parsed by the driver are
assumed to be in LE format.
This patch fix all the places where the code handles these packets and use
the correct endianness macros to handle them, as the driver handles the
packets in CPU format (LE or BE depending on the arch).
Signed-off-by: Ben Segal <bpsegal20@gmail.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The patch fix the DRAM usage accounting by adding a missing update of
the DRAM memory consumption, when a context is being torn down without an
organized release of the allocated memory.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
In case kernel context init fails during device initialization, both
hl_ctx_put() and kfree() are called, ending with a double free of the
kernel context.
Calling kfree() is needed only when a failure happens between the
allocation of the kernel context and its initialization, so move it to
there and remove it from the error flow.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
If fsg_disable() and fsg_set_alt() are called too closely to each
other (for example due to a quick reset/reconnect), what can happen
is that fsg_set_alt sets common->new_fsg from an interrupt while
handle_exception is trying to process the config change caused by
fsg_disable():
fsg_disable()
...
handle_exception()
sets state back to FSG_STATE_NORMAL
hasn't yet called do_set_interface()
or is inside it.
---> interrupt
fsg_set_alt
sets common->new_fsg
queues a new FSG_STATE_CONFIG_CHANGE
<---
Now, the first handle_exception can "see" the updated
new_fsg, treats it as if it was a fsg_set_alt() response,
call usb_composite_setup_continue() etc...
But then, the thread sees the second FSG_STATE_CONFIG_CHANGE,
and goes back down the same path, wipes and reattaches a now
active fsg, and .. calls usb_composite_setup_continue() which
at this point is wrong.
Not only we get a backtrace, but I suspect the second set_interface
wrecks some state causing the host to get upset in my case.
This fixes it by replacing "new_fsg" by a "state argument" (same
principle) which is set in the same lock section as the state
update, and retrieved similarly.
That way, there is never any discrepancy between the dequeued
state and the observed value of it. We keep the ability to have
the latest reconfig operation take precedence, but we guarantee
that once "dequeued" the argument (new_fsg) will not be clobbered
by any new event.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In some cases, one can get out of suspend with a reset or
a disconnect followed by a reconnect. Previously we would
leave a stale suspended flag set.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().
Fixes: cc995c9ec1 ("usb: gadget: udc: renesas_usb3: add support for usb role swap")
Cc: <stable@vger.kernel.org> # v4.12+
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add missing break statement in order to prevent the code from falling
through to case SH_BREAKPOINT_WRITE.
Fixes: 09a0729477 ("sh: hw-breakpoints: Add preliminary support for SH-4A UBC.")
Cc: stable@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Remove logically dead code and mark switch cases where we are expecting
to fall through.
Fix the following warnings (Building: defconfig sh):
arch/sh/kernel/disassemble.c:478:8: warning: this statement may fall
through [-Wimplicit-fallthrough=]
arch/sh/kernel/disassemble.c:487:8: warning: this statement may fall
through [-Wimplicit-fallthrough=]
arch/sh/kernel/disassemble.c:496:8: warning: this statement may fall
through [-Wimplicit-fallthrough=]
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
- Fix dax_layout_busy_page() to not discard private cow pages of fs/dax
private mappings.
- Update the memremap_pages core to properly cleanup on behalf of
internal reference-count users like device-dax.
-----BEGIN PGP SIGNATURE-----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=Se2X
-----END PGP SIGNATURE-----
Merge tag 'dax-fixes-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull dax fixes from Dan Williams:
"A filesystem-dax and device-dax fix for v5.3.
The filesystem-dax fix is tagged for stable as the implementation has
been mistakenly throwing away all cow pages on any truncate or hole
punch operation as part of the solution to coordinate device-dma vs
truncate to dax pages.
The device-dax change fixes up a regression this cycle from the
introduction of a common 'internal per-cpu-ref' implementation.
Summary:
- Fix dax_layout_busy_page() to not discard private cow pages of
fs/dax private mappings.
- Update the memremap_pages core to properly cleanup on behalf of
internal reference-count users like device-dax"
* tag 'dax-fixes-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
mm/memremap: Fix reuse of pgmap instances with internal references
dax: dax_layout_busy_page() should not unmap cow pages
Pull NVMe fixes from Sagi:
"Few nvme fixes for the next rc round.
- detect capacity changes on the mpath disk from Anthony
- probe/remove fix from Keith
- various fixes to pass blktests from Logan
- deadlock in reset/scan race fix
- nvme-rdma use-after-free fix
- deadlock fix when passthru commands race mpath disk info update"
* 'nvme-5.3-rc' of git://git.infradead.org/nvme:
nvme-pci: Fix async probe remove race
nvme: fix controller removal race with scan work
nvme-rdma: fix possible use-after-free in connect error flow
nvme: fix a possible deadlock when passthru commands sent to a multipath device
nvme-core: Fix extra device_put() call on error path
nvmet-file: fix nvmet_file_flush() always returning an error
nvmet-loop: Flush nvme_delete_wq when removing the port
nvmet: Fix use-after-free bug when a port is removed
nvme-multipath: revalidate nvme_ns_head gendisk in nvme_validate_ns
A few minor RISC-V updates for v5.3-rc4:
- Remove __udivdi3() from the 32-bit Linux port, converting the only
upstream user to use do_div(), per Linux policy
- Convert the RISC-V standard clocksource away from per-cpu data structures,
since only one is used by Linux, even on a multi-CPU system
- A set of DT binding updates that remove an obsolete text binding in
favor of a YAML binding, fix a bogus compatible string in the schema
(thus fixing a "make dtbs_check" warning), and clarifies the future
values expected in one of the RISC-V CPU properties
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEElRDoIDdEz9/svf2Kx4+xDQu9KksFAl1PO50ACgkQx4+xDQu9
Kks+aA//d2HVbYpsQT4dnK9HHySTEN8COpxAtXEyprqEqFvhGWiXHf/o5DZJS+KA
J0T4tnfajUxNzN+/B+Wvg8QRZyojad1gPQ8WpKGsRjVMtSZJuvo/knW1aVJPFr5S
28AjXyR5XVugvt5mNSNJTrPBeJ/bzNSZOLfat+gCsHBblNipdWwZhOwcM4mi3sQM
9fc8R5Mg0LHwNF0yVoA47WEwWgjXINkOE5ntvgNydiwoTc4noB046gy0ciZF04WS
YZMNRmr3BCL30zGZv6Ewu7xvcRYf84wjhIvPFkuaJHfxBzwAd4gulsytqGCQmFIC
Na7/5HOtzXpsS27hSev+1SGljv81p3rlKIBVxB2E1OH/eDl1U+yhm/AtM0wbXkpD
2UMHmKoSL/oYIXKOXwpWSKTGxNJbF1c56q4lwDVjq/kvg88GhFXQV/cQV1pS2Aao
KkqKl8AfxzoG3KNGKNJD42ztMW+3a3Wp215pGbrVVAwVOD8kFgCiM9RtqH2pTZrA
AjD/wpAaH9glGkCcwPovzOJ1XA9VKLy4nWLowv5zB9To1wbbAuYRj/7pUNm6LTWF
kcU0E6Yza5b2kKvwSzLdZa4W837XQrf3fRKMTTgH+fcjwma+GlLwx+f6Yk8AmTpP
TMSpV9C6M5RKLVqdzNWUT7q4dzTsNPXse5DhhhnMh3cBPHIGlzQ=
=DIhv
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"A few minor RISC-V updates for v5.3-rc4:
- Remove __udivdi3() from the 32-bit Linux port, converting the only
upstream user to use do_div(), per Linux policy
- Convert the RISC-V standard clocksource away from per-cpu data
structures, since only one is used by Linux, even on a multi-CPU
system
- A set of DT binding updates that remove an obsolete text binding in
favor of a YAML binding, fix a bogus compatible string in the
schema (thus fixing a "make dtbs_check" warning), and clarifies the
future values expected in one of the RISC-V CPU properties"
* tag 'riscv/for-v5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
dt-bindings: riscv: fix the schema compatible string for the HiFive Unleashed board
dt-bindings: riscv: remove obsolete cpus.txt
RISC-V: Remove udivdi3
riscv: delay: use do_div() instead of __udivdi3()
dt-bindings: Update the riscv,isa string description
RISC-V: Remove per cpu clocksource
Pull x86 fixes from Thomas Gleixner:
"A few fixes for x86:
- Don't reset the carefully adjusted build flags for the purgatory
and remove the unwanted flags instead. The 'reset all' approach led
to build fails under certain circumstances.
- Unbreak CLANG build of the purgatory by avoiding the builtin
memcpy/memset implementations.
- Address missing prototype warnings by including the proper header
- Fix yet more fall-through issues"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/lib/cpu: Address missing prototypes warning
x86/purgatory: Use CFLAGS_REMOVE rather than reset KBUILD_CFLAGS
x86/purgatory: Do not use __builtin_memcpy and __builtin_memset
x86: mtrr: cyrix: Mark expected switch fall-through
x86/ptrace: Mark expected switch fall-through
Pull perf tooling fixes from Thomas Gleixner:
"Perf tooling fixes all over the place:
- Fix the selection of the main thread COMM in db-export
- Fix the disassemmbly display for BPF in annotate
- Fix cpumap mask setup in perf ftrace when only one CPU is present
- Add the missing 'cpu_clk_unhalted.core' event
- Fix CPU 0 bindings in NUMA benchmarks
- Fix the module size calculations for s390
- Handle the gap between kernel end and module start on s390
correctly
- Build and typo fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf pmu-events: Fix missing "cpu_clk_unhalted.core" event
perf annotate: Fix s390 gap between kernel end and module start
perf record: Fix module size on s390
perf tools: Fix include paths in ui directory
perf tools: Fix a typo in a variable name in the Documentation Makefile
perf cpumap: Fix writing to illegal memory in handling cpumap mask
perf ftrace: Fix failure to set cpumask when only one cpu is present
perf db-export: Fix thread__exec_comm()
perf annotate: Fix printing of unaugmented disassembled instructions from BPF
perf bench numa: Fix cpu0 binding
Pull scheduler fixes from Thomas Gleixner:
"Three fixlets for the scheduler:
- Avoid double bandwidth accounting in the push & pull code
- Use a sane FIFO priority for the Pressure Stall Information (PSI)
thread.
- Avoid permission checks when setting the scheduler params for the
PSI thread"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/psi: Do not require setsched permission from the trigger creator
sched/psi: Reduce psimon FIFO priority
sched/deadline: Fix double accounting of rq/running bw in push & pull
Pull irq fix from Thomas Gleixner:
"A small fix for the affinity spreading code.
It failed to handle situations where a single vector was requested
either due to only one CPU being available or vector exhaustion
causing only a single interrupt to be granted.
The fix is to simply remove the requirement in the affinity spreading
code for more than one interrupt being available"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/affinity: Create affinity mask for single vector
Pull objtool warning fix from Thomas Gleixner:
"The recent objtool fixes/enhancements unearthed a unbalanced CLAC in
the i915 driver.
Chris asked me to pick the fix up and route it through"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
drm/i915: Remove redundant user_access_end() from __copy_from_user() error path
A compilation -Wimplicit-fallthrough warning was enabled by commit
a035d552a9 ("Makefile: Globally enable fall-through warning")
Even though clang 10.0.0 does not currently support this warning without
a patch, clang currently does not support a value for this option.
Link: https://bugs.llvm.org/show_bug.cgi?id=39382
The gcc default for this warning is 3 so removing the =3 has no effect
for gcc and enables the warning for patched versions of clang.
Also remove the =3 from an existing use in a parisc Makefile:
arch/parisc/math-emu/Makefile
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-and-tested-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some small char/misc driver fixes for 5.3-rc4.
Two of these are for the habanalabs driver for issues found when running
on a big-endian system (are they still alive?) The others are tiny
fixes reported by people, and a MAINTAINERS update about the location of
the fpga development tree.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXU6uwA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymBrQCfRh8brBuZ4ZoeP9aVgjkPDhwdBLkAn38RdH6c
96J1xGLZf1+CN7GVLnFD
=YUWU
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes Greg KH:
"Here are some small char/misc driver fixes for 5.3-rc4.
Two of these are for the habanalabs driver for issues found when
running on a big-endian system (are they still alive?) The others are
tiny fixes reported by people, and a MAINTAINERS update about the
location of the fpga development tree.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
coresight: Fix DEBUG_LOCKS_WARN_ON for uninitialized attribute
MAINTAINERS: Move linux-fpga tree to new location
nvmem: Use the same permissions for eeprom as for nvmem
habanalabs: fix host memory polling in BE architecture
habanalabs: fix F/W download in BE architecture
