After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.
Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
smp_mb__before_clear_bit();
clear_bit(NAPI_STATE_SCHED, &n->state);
}
[37255.571996] Kernel panic - not syncing: BUG!
[37255.595234] Call trace:
[37255.597694] [<ffff80000008ab48>] dump_backtrace+0x0/0x1a0
[37255.603114] [<ffff80000008ad08>] show_stack+0x20/0x28
[37255.608187] [<ffff8000009c4944>] dump_stack+0x98/0xb8
[37255.613258] [<ffff8000009c149c>] panic+0x10c/0x26c
[37255.618070] [<ffff80000070f134>] hns_nic_net_up+0x30c/0x4e0
[37255.623664] [<ffff80000070f39c>] hns_nic_net_open+0x94/0x12c
[37255.629346] [<ffff80000084be78>] __dev_open+0xf4/0x168
[37255.634504] [<ffff80000084c1ac>] __dev_change_flags+0x98/0x15c
[37255.640359] [<ffff80000084c29c>] dev_change_flags+0x2c/0x68
[37255.769580] [<ffff8000008dc400>] devinet_ioctl+0x650/0x704
[37255.775086] [<ffff8000008ddc38>] inet_ioctl+0x98/0xb4
[37255.780159] [<ffff800000827b7c>] sock_do_ioctl+0x44/0x84
[37255.785490] [<ffff800000828e04>] sock_ioctl+0x248/0x30c
[37255.790737] [<ffff80000026dc6c>] do_vfs_ioctl+0x480/0x618
[37255.796156] [<ffff80000026de94>] SyS_ioctl+0x90/0xa4
[37255.801139] SMP: stopping secondary CPUs
[37255.805079] kbox: catch panic event.
[37255.809586] collected_len = 128928, LOG_BUF_LEN_LOCAL = 131072
[37255.816103] flush cache 0xffff80003f000000 size 0x800000
[37255.822192] flush cache 0xffff80003f000000 size 0x800000
[37255.828289] flush cache 0xffff80003f000000 size 0x800000
[37255.834378] kbox: no notify die func register. no need to notify
[37255.840413] ---[ end Kernel panic - not syncing: BUG!
This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hip06 datasheet:
1.Six registers use wrong address:
RCB_COM_SF_CFG_INTMASK_RING
RCB_COM_SF_CFG_RING_STS
RCB_COM_SF_CFG_RING
RCB_COM_SF_CFG_INTMASK_BD
RCB_COM_SF_CFG_BD_RINT_STS
DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
overwrite
These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
and install them again, must use "ifconfig down/ifconfig up"
command pair to bring port to work.
This patch calls phy_stop function when init phy to fix this bug.
2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
all ports can not use anymore, because of the phy devices register
failed(phy devices already exists).
Phy devices are registered when hns_dsaf installed, this patch
removes them when hns_dsaf removed.
The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for the Telit LN940 series cellular modules QMI interface.
QMI_QUIRK_SET_DTR quirk requied for Qualcomm MDM9x40 chipset.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for Fibocom NL668 series QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The get_mac_address() function is normally inline, but when it is
not, we get a warning that this configuration is broken:
WARNING: vmlinux.o(.text+0x4aff00): Section mismatch in reference from the function w90p910_ether_setup() to the function .init.text:get_mac_address()
The function w90p910_ether_setup() references
the function __init get_mac_address().
This is often because w90p910_ether_setup lacks a __init
Remove the __init to make it always do the right thing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All previous docks and dongles that have supported this feature use
the RTL8153-AD chip.
RTL8153-BND is a new chip that will be used in upcoming Dell type-C docks.
It should be added to the whitelist of devices to activate MAC address
pass through.
Per confirming with Realtek all devices containing RTL8153-BND should
activate MAC pass through and there won't use pass through bit on efuse
like in RTL8153-AD.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
corrected macro used in tx path. removed redundant hdrlen
and check for !page in chtls_sendmsg
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning:
tentative array definition assumed to have one element
static const struct acpi_device_id xgene_enet_acpi_match[];
^
1 warning generated.
Both xgene_enet_acpi_match and xgene_enet_of_match are defined before
their uses at the bottom of the file so this is unnecessary. When
CONFIG_ACPI is disabled, ACPI_PTR becomes NULL so xgene_enet_acpi_match
doesn't need to be defined.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value for OEM_CFG_UPDATE command differs between driver and the
Management firmware (mfw). Fix this gap with adding a reserved field.
Fixes: cac6f69154 ("qed: Add support for Unified Fabric Port.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcEiXXAAoJEEg/ir3gV/o+xxQH/jGS6GQrty9puL40sXKE4ryK
GKVSwbKLnu4WatPcLe/CGxJwRoCVUUKfsbprsuy+oYxhUd5M5h6qu215kZgsfdDC
CfxznbEj3o6mN+ZyZjL+F2gEG6e96bpkKvayb2a9YYQaY/9+V6CMKh3U5jHI+Q2V
D4ToCjWbMXkQ0jsevfpV9W2T0DNfXIa5QGvsvH+D+PoLF/ke/YALZd+yJT0Cm9N2
/vp0qvnHnZO5YavEThN2Lh8f9AY/pAwuGgTrPyddfkZC/6QLH+c8948gF14V+03l
Nz78uSpurQ97X511UBcabSQB0xTCHSAw3/SKCVSxFrpMvkhj4mTbjohwc567Gy4=
=YxUz
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-12-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-fixes-2018-12-13
Subject: [pull request][net 0/9] Mellanox, mlx5 fixes 2018-12-13
Saeed Mahameed says:
====================
This series introduces some fixes to the mlx5 core and mlx5e netdevice
driver.
=======
Conflict with net-next: When merged with net-next this series will
cause a moderate conflict:
1) in drivers/net/ethernet/mellanox/mlx5/core/en_tc.c (2 hunks)
Take hunks from net only and just replace *attr->mirror_count to *attr->split_count
1.1) there is one more instance of slow_attr->mirror_count to be replaced
with slow_attr->split_count, it doesn't appear in the conflict, it will
cause a compilation error if left out.
2) in mlx5_ifc.h, take hunks only from net.
Example for the merge resolution can be found at:
https://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux.git/commit/?h=merge/mlx5-fixes&id=48830adf29804d85d77ed8a251d625db0eb5b8a8
branch merge/mlx5-fixes of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
(I simply merged this pull request tag into net-next and resolved the conflict)
I don't know if it's ok with you, but to save your time, you can just:
git pull git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux merge/mlx5-fixes
Into net-next, before your next net merge, and you will have a clean
merge of net into net-next (at least for mlx5 files).
======
Please pull and let me know if there's any problem.
For -stable v4.18
338d615be484 ('net/mlx5e: Cancel DIM work on close SQ')
91f40f9904ad ('net/mlx5e: RX, Verify MPWQE stride size is in range')
For -stable v4.19
c5c7e1c41bbe ('net/mlx5e: Remove unused UDP GSO remaining counter')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TXQ SQ closure is followed by closing the corresponding CQ. A pending
DIM work would try to modify the now non-existing CQ.
This would trigger an error:
[85535.835926] mlx5_core 0000:af:00.0: mlx5_cmd_check:769:(pid 124399):
MODIFY_CQ(0x403) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1d7771)
Fix by making sure to cancel any pending DIM work before destroying the SQ.
Fixes: cbce4f4447 ("net/mlx5e: Enable adaptive-TX moderation")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove tx_udp_seg_rem counter from ethtool output, as it is no longer
being updated in the driver's data flow.
Fixes: 3f44899ef2 ("net/mlx5e: Use PARTIAL_GSO for UDP segmentation")
Signed-off-by: Mikhael Goikhman <migo@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, we are deleting offloaded encap flows in case the relevant neigh
becomes unconnected while the encap is valid (a sign that it used to be
connected), or if the curr neigh mac is different from the cached mac
(a sign that the remote side changed their mac).
The 2nd check also applies when the neigh becomes connected on the 1st
time (we start with zero mac). Before the offending commit, the deleting
handler was practically no op, as no flows were offloaded. But since
that commit, we offload neigh-less encap flows to slow path.
Under mirroring scheme, we go into the delete handler, attempt to unoffload a
mirror rule which was never set (as we were offloading to slow path) and crash.
Fix that by calling the delete handler only when the encap is valid,
which covers both cases mentioned above.
Fixes: 5dbe906ff1 ('net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When a neighbour is resolved, we delete the goto slow path rule from HW.
The eswitch flow attributes where not properly initialized on that case,
hence we mess up the eswitch refcounts for chain zero (the default one).
Fix that along with making sure to use semicolons and not commas on that code;
Fixes: 5dbe906ff1 ('net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Just a leftover which was wrongly left there, remove it while spawning
a message to suggest firmware upgrade.
Fixes: bf07aa730a ('net/mlx5e: Support offloading tc priorities and chains for eswitch flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we are not supporting this and not err-ing on that either.
For now, just err if asked to do that.
Fixes: bf07aa730a ('net/mlx5e: Support offloading tc priorities and chains for eswitch flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add check of MPWQE stride size is within range supported by HW. In case
calculated MPWQE stride size exceed range, linear SKB can't be used and
we should use non linear MPWQE instead.
Fixes: 619a8f2a42 ("net/mlx5e: Use linear SKB in Striding RQ")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The default amount of channels a representor opens was erroneously
changed from one to the maximum amount of channels, restore to its
intended value.
Fixes: 779d986d60 ("net/mlx5e: Do not ignore netdevice TX/RX queues number")
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2018-12-12
This series contains fixes to i40e and ixgbe.
Stefan Assmann fixes an issue created by a previous fix, where
ether_addr_copy() was moved to avoid a race but did not take into
account that it alters the MAC address being handed to
i40e_del_mac_filter().
Michał Mirosław provides 2 fixes for i40e, first resolves issues in the
hardware VLAN offload where VLAN.TCI equal to 0 was being dropped and a
race between disabling VLAN receive feature in hardware and processing
the receive queue, where packets could have their VLAN information
dropped.
Ross Lagerwall fixes a racy condition during a ixgbe VF reset, where
writing the register to issue a reset and sending the reset message via
the mailbox API could result of the mailbox memory getting cleared
during the reset before the message gets successfully sent which results
in a VF driver malfunction.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver sends update-SVID ramrod in the MFW notification path.
If there is a pending ramrod, driver doesn't retry the command
and storm firmware will never be updated with the SVID value.
The patch adds changes to send update-svid ramrod in process context with
retry/poll flags set.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will be only one PHC clock per port. PTP should be enabled only on
one PF per port. The change enables PTP functionality on the PF that
initializes the port. The change is useful in multi-function modes e.g.,
NPAR where a port can have more than one PF.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF driver does a reset, it (at least the Linux one) writes to
the VFCTRL register to issue a reset and then immediately sends a reset
message using the mailbox API. This is racy because when the PF driver
detects that the VFCTRL register reset pin has been asserted, it clears
the mailbox memory. Depending on ordering, the reset message sent by
the VF could be cleared by the PF driver. It then responds to the
cleared message with a NACK which causes the VF driver to malfunction.
Fix this by deferring clearing the mailbox memory until the reset
message is received.
Fixes: 939b701ad6 ("ixgbe: fix driver behaviour after issuing VFLR")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move rx_ptype extracting to i40e_process_skb_fields() to avoid
duplicating the code.
Signed-off-by: Michał Mirosław <michal.miroslaw@atendesoftware.pl>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function hso_probe reads if_num from the USB device (as an u8) and uses
it without a length check to index an array, resulting in an OOB memory read
in hso_probe or hso_get_config_data.
Add a length check for both locations and updated hso_probe to bail on
error.
This issue has been assigned CVE-2018-19985.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes two bugs in hardware VLAN offload:
1. VLAN.TCI == 0 was being dropped
2. there was a race between disabling of VLAN RX feature in hardware
and processing RX queue, where packets processed in this window
could have their VLAN information dropped
Fix moves the VLAN handling into i40e_process_skb_fields() to save on
duplicated code. i40e_receive_skb() becomes trivial and so is removed.
Signed-off-by: Michał Mirosław <michal.miroslaw@atendesoftware.pl>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous commit moved the ether_addr_copy() in i40e_set_mac() before
the mac filter del/add to avoid a race. However it wasn't taken into
account that this alters the mac address being handed to
i40e_del_mac_filter().
Also changed i40e_add_mac_filter() to operate on netdev->dev_addr,
hopefully that makes the code easier to read.
Fixes: 458867b2ca ("i40e: don't remove netdev->dev_addr when syncing uc list")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.
Fixes: 38caff5a44 ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2018-12-11
An update from ieee802154 for your *net* tree.
Just two more fixes for ieee802154 dribver before the final 4.20 release.
Alexander Aring fixes a problem in the nested parsing code of the
hwsim driver interface.
A fix for a potential overflow in the ca8210 driver by Yue Habing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warning this:
drivers/net/ieee802154/ca8210.c:730:10: warning:
comparison is always false due to limited range of data type [-Wtype-limits]
'len' is u8 type, we get it from buf[1] adding 2, which can overflow.
This patch change the type of 'len' to unsigned int to avoid this,also fix
the gcc warning.
Fixes: ded845a781 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Previously we did not ensure tcp flags have a place to be stored
when using IPv6. We correct this by including IPv6 key layer when
we match tcp flags and the IPv6 key layer has not been included
already.
Fixes: 07e1671cfc ("nfp: flower: refactor shared ip header in match offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CP rings are accounted differently on the new 57500 chips. There
must be enough CP rings for the sum of RX and TX rings on the new
chips. The current logic may be over-estimating the RX and TX rings.
The output parameter max_cp should be the maximum NQs capped by
MSIX vectors available for networking in the context of 57500 chips.
The existing code which uses CMPL rings capped by the MSIX vectors
works most of the time but is not always correct.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 57500 chips have introduced the NQ structure in addition to
the existing CP rings in all chips. We need to introduce a new
bnxt_nq_rings_in_use(). On legacy chips, the 2 functions are the
same and one will just call the other. On the new chips, they
refer to the 2 separate ring structures. The new function is now
called to determine the resource (NQ or CP rings) associated with
MSIX that are in use.
On 57500 chips, the RDMA driver does not use the CP rings so
we don't need to do the subtraction adjustment.
Fixes: 41e8d79837 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 57500 chips use 1 NQ per MSIX vector, whereas legacy chips use
1 CP ring per MSIX vector. To better unify this, add a resv_irqs
field to struct bnxt_hw_resc. On legacy chips, we initialize resv_irqs
with resv_cp_rings. On new chips, we initialize it with the allocated
MSIX resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to support the 57500 devices have created this
regression. The bnxt_hwrm_queue_qportcfg() call was moved to be
called earlier before the RDMA support was determined, causing
the CoS queues configuration to be set before knowing whether RDMA
was supported or not. Fix it by moving it to the right place right
after RDMA support is determined.
Fixes: 98f04cf0f1 ("bnxt_en: Check context memory requirements from firmware.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_ppp and tx_ppp can be set between 0 and 255, so don't clamp to 1.
Fixes: 6e8814ceb7 ("net/mlx4_en: Fix mixed PFC and Global pause user control requests")
Signed-off-by: Tarick Bedeir <tarick@google.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 624ca9c33c.
This commit is completely bogus. The STACR register has two formats, old
and new, depending on the version of the IP block used. There's a pair of
device-tree properties that can be used to specify the format used:
has-inverted-stacr-oc
has-new-stacr-staopc
What this commit did was to change the bit definition used with the old
parts to match the new parts. This of course breaks the driver on all
the old ones.
Instead, the author should have set the appropriate properties in the
device-tree for the variant used on his board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.
The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.
Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.
Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.
Fixes: 4607f6d269 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().
Drop the reference when this unlikely error is hit.
Fixes: 1c30d1836a ("mlxsw: spectrum: Enable VxLAN enslavement to bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.
Fix by removing these warnings for now.
Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.
Fixes: 6e6030bd54 ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* hwsim
* AP mode (client powersave related)
* CSA/FTM interaction
* a busy loop in IE handling
* and similar
-----BEGIN PGP SIGNATURE-----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=MDbC
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg:
====================
As it's been a while, we have various fixes for
* hwsim
* AP mode (client powersave related)
* CSA/FTM interaction
* a busy loop in IE handling
* and similar
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.
Catch the uninitialized PHY mode case, and allow 10G rates.
Fixes: d97c9f4ab0 ("net: mvpp2: 1000baseX support")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
