In the case where lo_vag <= SGTL5000_LINE_OUT_GND_BASE, lo_vag
is set to zero and later vol_quot is computed by dividing by
lo_vag causing a division by zero error. Fix this by avoiding
a zero division and set vol_quot to zero in this specific case
so that the lowest setting for i is correctly set.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The !port check is redundant as it being performed in the following
check. Remove it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to short circuit detection, when the ADC/DAC is saturated and
overflows poor audio quality can result and should be reported to the
user. This device support Automatic Dynamic Range Compression (DRC)
to reduce this but it is not enabled currently in this driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These devices support detecting and reporting short circuits across
the output stages. Add support for reporting these issue. Do this
by registering an interrupt if available and enabling this error
to trigger that interrupt in the device.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TAS6426 has a register that reports channel faults such as
overcurrent and continuous DC output. Add reporting of this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When there is no fault bit set in a fault register we skip the fault
reporting section for that register. This also skips over saving that
registers value. We save the value so we will not double report an
error, but if an error clears then returns we will also not report it
as we did not save the all cleared register value. Fix this by saving
the fault register value in the all clear path.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The current short version of the register name may be
ambiguous when another fault register detection is added.
Use the full name.
While here fix comment about clearing faults, the CLEAR_FAULT
register actually only clears sticky bits, which are only
warnings, fault bits can only cleared by resolving the fault.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a S/PDIF enable switch as a SOC_SINGLE.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cs4265 uses 32 bit transport on the I2S bus. This patch enables native
32 bit mode for machine drivers which use this sound card driver.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cs4265 driver declares the "MMTLR Data Switch" register setting with
a 0 register value rather then the 0x12 register (CS4265_SPDIF_CTL2).
This incorrect value causes alsamixer to fault with the output :
cannot load mixer controls: Input/output error
This patch corrects the register value. alsamixer now runs.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike the TAS5720, the TAS5722 can be configured to utilize 16-bit wide
slots in TDM mode. This can help easing audio clocking/frequency
requirements.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TAS5722 supports modifying volume in 0.25dB steps (as opposed to
0.5dB steps on the TAS5720). Introduce a custom mixer control that
allows taking advantage of this finer output volume granularity.
Also add custom getters/setters for access as the TAS5722 digital volume
controls are split over two registers.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before this patch the only alias provided by the dmic module is:
alias: platform:dmic-codec
Device instantiated from DT will not probe automatically with this
After this patch, here is the new alias list:
alias: platform:dmic-codec
alias: of:N*T*Cdmic-codecC*
alias: of:N*T*Cdmic-codec
Now the dmic codec probes automatically when instantiated from DT.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Kconfig prompt for the generic digital mic to make it configurable
through menuconfig
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
adau17x1_setup_firmware and adau17x1_has_dsp is only used internally, so
making them static instead of exported.
Signed-off-by: Robert Rosengren <robertr@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modified some if-statements to make them more clear
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modified the complete file comments in C++ style, to make them look more
intentional
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds support for TI PCM3060 CODEC.
The technical documentation is available at [1].
[1] http://ti.com/product/pcm3060
Signed-off-by: Kirill Marinushkin <kmarinushkin@birdec.tech>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: M R Swami Reddy <mr.swami.reddy@ti.com>
Cc: Vishwas A Deshpande <vishwas.a.deshpande@ti.com>
Cc: Kevin Cernekee <cernekee@chromium.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The Thinkpad 8 needs a quirk for jack-detect and the internal mic to
work correctly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Safeload support has been implemented which is used
when updating for instance filter parameters using
alsa controls. Without safeload support audio can
become distorted during update.
Signed-off-by: Danny Smith <dannys@axis.com>
Signed-off-by: Robert Rosengren <robertr@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixed range in safeload conditional to allow safeload to up to 20 bytes,
without a lower limit.
Signed-off-by: Danny Smith <dannys@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a kernel module which is used by the legacy HDA
codec drivers as library. This implements hdac_ext_bus_ops to enable
the reuse of legacy HDA codec drivers with ASoC platform drivers.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HID made of either Wolfson/CirrusLogic PCI ID + 8804 identifier.
This helps enumerate the HifiBerry Digi+ HAT boards on the Up2 platform.
The scripts at https://github.com/thesofproject/acpi-scripts can be
used to add the ACPI initrd overlays.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
New calibration sequence allows rt5682 do calibration without
MCLK.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The step of DAC/ADC volume scale changes from 0.375dB to 0.75dB
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
After our evaluation, we need to modify the default values to make sure
the volume applied immediately.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 143b44845d ("ASoC: wm9712: replace codec to component")
"wm9712-codec" got renamed to "wm9712-component", however, this change
never got propagated down to the actual board/platform drivers. E.g. on
Colibri T20 this lead to the following spew upon boot with sound/touch
being broken:
[ 2.214121] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 2.222137] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 2.344384] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 2.351885] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 2.668339] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 2.675811] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 3.208408] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 3.216312] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 3.235397] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 3.248938] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 14.970443] ALSA device list:
[ 14.996628] No soundcards found.
This commit finally fixes this again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
A fairly big update, including quite a bit of core activity this time
around (which is good to see) along with a fairly large set of new
drivers.
- A new snd_pcm_stop_xrun() helper which is now used in several
drivers.
- Support for providing name prefixes to generic component nodes.
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing.
- Generalization of the DIO2125 support to a simple amplifier driver.
- Accessory detection support for the audio graph card.
- DT support for PXA AC'97 devices.
- Quirks for a number of new x86 systems.
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltxVZsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0CtwB/0U+IUWLlojWD6RDfueycvc9TiZW0t4
gBT3OD8f4oif0MuMy6oE2ag8JPNU8n5MnO14U366GDaEyZPj79W7f50Q8Nnyht/n
py6fQfyo7Ec2hFJstDI42KvDymTbAer6hnAUJarr/FdZHdGeOfYV+s7aHp5aEQAS
KACnX8qWo87VePouNBorqWXWueAJTb6zpWy7YQ1KGb/pJIAeue2Y9pLRGXQos1BS
E1AP+ge2BMnz7BeiCgw/39hN6X545nJ1fcZKuIu8Gqy9ahqEDHgmBWPAehtGnfVj
D8JPplTaBFtAsJwi18b7ApWtcytpizPPN/l3NTA4fTRJQe9kxfDmnE7b
=fvKX
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.19
A fairly big update, including quite a bit of core activity this time
around (which is good to see) along with a fairly large set of new
drivers.
- A new snd_pcm_stop_xrun() helper which is now used in several
drivers.
- Support for providing name prefixes to generic component nodes.
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing.
- Generalization of the DIO2125 support to a simple amplifier driver.
- Accessory detection support for the audio graph card.
- DT support for PXA AC'97 devices.
- Quirks for a number of new x86 systems.
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707.
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056531 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms it has been noted that a pop noise can be
witnessed when capturing audio, mainly for first time after a
headset jack has been inserted. This is due to a DC offset in the
Mic PGA and so to avoid this delays are required when powering
up the capture path.
This commit rectifies the problem by adding delays post Mic PGA and
post Mixin PGA. The post Mic PGA delay is determined based on
Mic Bias voltage, and is only applied the first time after a
headset jack is inserted.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of harcoding that a core must always be called "DSPn"
add a name member to struct wm_adsp so that the owning codec
driver can provide a custom name. This allows for re-use of
the wm_adsp driver with parts where the processing cores are
named differently.
If no name is provided the default DSPn name is used.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To allow for more flexibility in naming of DSP-type cores
move the creation of the firmware controls to the codec
drivers instead of having a hardcoded list in wm_adsp.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset of the DSP core needs to be taken into account for the DSP
preloader control get and put. Currently the dsp->preloaded variable
will only ever be read/updated on the first DSP, whilst this doesn't
affect the operation of the control the readback will be incorrect.
Signed-off-by: Ajit Pandey <ajit.pandey@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The driver expects to find the device id in rt5677_of_match.data, however
it is currently assigned to rt5677_of_match.type. Fix this.
The problem was found with the help of clang:
sound/soc/codecs/rt5677.c:5010:36: warning: expression which evaluates to
zero treated as a null pointer constant of type 'const void *'
[-Wnon-literal-null-conversion]
{ .compatible = "realtek,rt5677", RT5677 },
^~~~~~
Fixes: ddc9e69b9d ("ASoC: rt5677: Hide platform data in the module sources")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing break statement in order to prevent the code from falling
through to the default case.
Addresses-Coverity-ID: 115050 ("Missing break in switch")
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115050 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1357430 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115045 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115043 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 146354 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115042 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115041 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115047 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1271174 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056547 ("Missing break in switch")
Addresses-Coverity-ID: 1056548 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1271173 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit e57d4ca882 (ASoC: wcd9335: add support to wcd9335
codec) due to build failures caused by missing dependencies.
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit c8cb5f775c (ASoC: vert "ASoC: wcd9335: add
CLASS-H Controller support) due to missing dependencies.
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable osrate is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'osrate' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CLASS-H controller/Amplifier is common accorss Qualcomm WCD codec series.
This patchset adds basic CLASS-H controller apis for WCD codecs after
wcd9335 to use.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm WCD9335 Codec is a standalone Hi-Fi audio codec IC,
It supports both I2S/I2C and SLIMbus audio interfaces.
On slimbus interface it supports two data lanes; 16 Tx ports
and 8 Rx ports. It has Seven DACs and nine dedicated interpolators,
Seven (six audio ADCs, and one VBAT ADC), Multibutton headset
control (MBHC), Active noise cancellation and Sidetone paths
and processing.
This patchset adds very basic support for playback and capture
via the 9 interpolators and ADC respectively.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove duplicated entry and add missing zero in rate constraints.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCM format type is with __bitwise, so we should use the dedicated
snd_pcm_format_t instead of int.
This fixes the sparse warning like:
sound/soc/codecs/pcm186x.c:268:44: warning: incorrect type in initializer (different base types)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch fixes the issue of the delay volume applied.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull the generic drm_audio_component support, which will be used later
for AMD/ATI and other HD-audio HDMI codec drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a mixer control for the IN3 Boost volume, IN3 is used for the headset
mic on most devices, so this is necessary to control the headset mic
volume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the compressed streams in DSP firmwares are
identified essentially by looking at a fixed location inside
the firmware. This is fragile and also limits things to a
single compressed stream.
Here a new form of firmware parameter is added, the HOST_BUFFER
which identifies a compressed stream from meta-data in the
firmware file. This is more robust and allows for the possiblity
of using multiple streams per core in the future. Currently the
implementation is still limited to a single stream and will
use the first HOST_BUFFER parameter encountered. If there aren't
any HOST_BUFFER parameters it will fall back to the legacy way
of finding the host buffer.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Newer voice control firmwares can capture multiple audio channels.
Allow up to 8 channels for future-proofing.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when creating ALSA control names for the DSP the length of any
prefix applied to the CODEC is not taken into account. Whilst this is
mostly harmless it does result in ALSA doing the truncation of the
control names and printing a warning. It is better to have the driver do
the truncation so it can truncate from the start of parameter name
itself to give a greater chance of the result maintain a unique name.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6396bb2215 ("treewide: kzalloc() -> kcalloc()") was
overlooked when doing some refactoring to the algorithm list
handling, which lead to twice as much buffer being allocated
as required for reading the algorithm list. A kcalloc is no
longer appropriate since the allocation size is now in bytes
not registers, as such change back to kzalloc.
Fixes: 7f7cca08ab ("ASoC: wm_adsp: Simplify handling of alg offset and length")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All controls derived from the loaded firmware should be created prior
to returning from the preloader's put function, such that they are
immediately available to user-space.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for power management of HDAC HDMI codec device for
various scenarios such as S0/S3, probe and playback use case.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_lib_mmap_vmalloc() was supposed to be implemented with
somewhat special for vmalloc handling, but in the end, this turned to
just the default handler, i.e. NULL. As the situation has never
changed over decades, let's rip it off.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is the final step for more generic support of DRM audio
component. The generic audio component code is now moved to its own
file, and the symbols are renamed from snd_hac_i915_* to
snd_hdac_acomp_*, respectively. The generic code is enabled via the
new kconfig, CONFIG_SND_HDA_COMPONENT, while CONFIG_SND_HDA_I915 is
kept as the super-class.
Along with the split, three new callbacks are added to audio_ops:
pin2port is for providing the conversion between the pin number and
the widget id, and master_bind/master_unbin are called at binding /
unbinding the master component, respectively. All these are optional,
but used in i915 implementation and also other later implementations.
A note about the new snd_hdac_acomp_init() function: there is a slight
difference between this and the old snd_hdac_i915_init(). The latter
(still) synchronizes with the master component binding, i.e. it
assures that the relevant DRM component gets bound when it returns, or
gives a negative error. Meanwhile the new function doesn't
synchronize but just leaves as is. It's the responsibility by the
caller's side to synchronize, or the caller may accept the
asynchronous binding on the fly.
v1->v2: Fix missing NULL check in master_bind/unbind
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio i915 binding code contains a single pointer, hdac_acomp,
for allowing the access to audio component from the master bind/unbind
callbacks. This was needed because the callbacks pass only the device
pointer and we can't guarantee the object type assigned to the drvdata
(which is free for each controller driver implementation).
And this implementation will be a problem if we support multiple
components for different DRM drivers, not only i915.
As a solution, allocate the audio component object via devres and
associate it with the given device, so that the component callbacks
can refer to it via devres_find().
The removal of the object is still done half-manually via
devres_destroy() to make the code consistent (although it may work
without the explicit call).
Also, the snd_hda_i915_register_notifier() had the reference to
hdac_acomp as well. In this patch, the corresponding code is removed
by passing hdac_bus object to the function, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For allowing other drivers to use the DRM audio component, rename the
i915_audio_component_* with drm_audio_component_*, and split the
generic part into drm_audio_component.h. The i915 specific stuff
remains in struct i915_audio_component, which contains
drm_audio_component as the base.
The license of drm_audio_component.h is kept to MIT as same as the the
original i915_component.h.
This is a preliminary change for further development, and no
functional changes by this patch itself, merely code-split and
renames.
v1->v2: Use SPDX for drm_audio_component.h, fix remaining i915
argument in drm_audio_component.h
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 943fa02282 ("ASoC: hdmi-codec: Use different name for playback
streams") broke hdmi-codec's routing between it's output "TX" widget
and the S/PDIF or I2S streams by renaming the streams.
Whether an error occurs or not is dependent on whether there is another
widget called "Playback" registered by some other component - if there
is, that widget will be (incorrectly) bound to the HDMI codec's "TX"
output widget. If we end up connecting "TX" incorrectly, it can result
in components not being started, causing no audio output.
Since the I2S and S/PDIF streams now have different names, we can't
use a static route at component level to describe the relationship, so
arrange to dynamically create the route when the DAI driver is probed.
Fixes: 943fa02282 ("ASoC: hdmi-codec: Use different name for playback streams")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable button press detection for headsets by using the ovcd IRQ to get
notified of button presses.
This is modelled after (almost exactly copied from) the button press code
for the rt5640 which has identical ovcd hardware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the machine driver to disable jack-detect over a suspend/resume by
calling snd_soc_component_set_jack(NULL).
Note this renames rt5651_set_jack, where all the jack-enable work was done
to rt5651_enable_jack_detect. This function can now no longer fail as it
does not request the IRQ anymore. It can still be passed an invalid jack
source, but that should never happen, so this is now logged and treated as
no jack source.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On removal we must free the IRQ *before* cancelling the jack-detect work,
so that the jack-detect work cannot be rescheduled by the IRQ.
Before this commit we were cancelling the jack-detect work from the
driver remove callback, while relying on devm to free the IRQ, which
happens after the remove callback.
This is the wrong order. This commit uses a devm-action to register
a devm callback which cancels the work, before requesting the IRQ
(devm tears things down in reverse order). This also allows us to
remove the now empty remove driver callback.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The playback DAI is connected to the DSP and the DSP might be sourcing
signals from the playback stream. Add a DAPM route between the two to make
sure that the playback DAI is powered up, when the DSP is active.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Addresses-Coverity-ID: 1432039 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Addresses-Coverity-ID: 1339616 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the es7154 which is basically an es7134 with an
embedded power amplifier and lower maximum sample rate
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop AVDD in favor of PVDD to match the names used in the datasheet
and only claim PVDD on the es7154. The es7134 and es7144 don't have
a separate supply for the digital I/O.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the everest es7241 which is a simple 2 channels
analog to digital converter.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
