Pull irq fixes from Thomas Gleixner:
"A set of small fixes for the irq subsystem:
- Cure a data ordering problem with chained interrupts
- Three small fixlets for the mbigen irq chip"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix chained interrupt data ordering
irqchip/mbigen: Fix the clear register offset calculation
irqchip/mbigen: Fix potential NULL dereferencing
irqchip/mbigen: Fix memory mapping code
The register array offset for clearing an interrupt is calculated by:
offset = (hwirq - RESERVED_IRQ_PER_MBIGEN_CHIP) / 32;
This is wrong because the clear register array includes the reserved
interrupts. So the clear operation ends up in the wrong register.
This went unnoticed so far, because the hardware clears the real bit
through a timeout mechanism when the hardware is configured in debug
mode. That debug mode was enabled on early generations of the hardware, so
the problem was papered over.
On newer hardware with updated firmware the debug mode was disabled, so the
bits did not get cleared which causes the system to malfunction.
Remove the subtraction of RESERVED_IRQ_PER_MBIGEN_CHIP, so the correct
register is accessed.
[ tglx: Rewrote changelog ]
Fixes: a6c2f87b88 ("irqchip/mbigen: Implement the mbigen irq chip operation functions")
Signed-off-by: MaJun <majun258@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: linuxarm@huawei.com
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Link: http://lkml.kernel.org/r/1494561328-39514-4-git-send-email-guohanjun@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some mbigens share memory regions, and devm_ioremap_resource
does not allow to share resources which will break the probe
of mbigen, in opposition to devm_ioremap.
This patch restores back usage of devm_ioremap function, but
with proper error handling and logging.
Fixes: 216646e4d8 ("irqchip/mbigen: Fix return value check in mbigen_device_probe()")
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: linuxarm@huawei.com
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: MaJun <majun258@huawei.com>
Link: http://lkml.kernel.org/r/1494561328-39514-2-git-send-email-guohanjun@huawei.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). Use devm_ioremap_resource() instead of devm_ioremap()
to fix the IS_ERR() test issue.
Fixes: 76e1f77f9c ("irqchip/mbigen: Introduce mbigen_of_create_domain()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/20170427152113.31147-1-weiyj.lk@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 4cfffcfa51 ("irqchip/mips-gic: Fix local interrupts") fixed
local interrupts by creating virq mappings for them all at startup.
Unfortunately this change broke legacy IRQ controllers in the same
system, such as the i8259 on the Malta platform, as it allocates virq
numbers that were expected to be available for the legacy controller.
Instead of creating the mappings statically when the GIC is probed,
re-introduce the irq domain .map function, removed by commit e875bd66df
("irqchip/mips-gic: Fix local interrupts") and use it to set up the irq
handler and chip. Since a good deal of the required functionality is
already implemented by gic_irq_domain_alloc, repurpose that function for
gic_irq_domain_map and add a new gic_irq_domain_alloc which wraps
gic_irq_domain_map with the necessary conversion.
This change fixes the legacy interrupt controller of the Malta platform
without breaking the perf interrupt fixed by commit e875bd66df
("irqchip/mips-gic: Fix local interrupts").
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492679256-14513-4-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In commit c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Qais indicates that he felt having a separate device IRQ domain was
cleaner, but along with everyone else I'm aware of touching this driver
I disagree.
Remove the separate device IRQ domain so that we simply have the main
GIC IRQ domain used for devices, and an IPI IRQ domain as a child. The
logic for handling the device interrupts & IPIs is cleanly separated
into the appropriate domain ops, making it much easier to reason about
what the driver is doing than the previous approach where the 2 child
domains had to call up to their parent, which had to handle both types
of interrupt & had all sorts of weird & wonderful duplication or
outright clobbering of setup performed by multiple domains.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492679256-14513-3-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since commit 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy
domain") introduced the GIC IPI IRQ domain we have tracked both
reservation of interrupts & their use with a single bitmap - ipi_resrv.
If an interrupt is reserved for use as an IPI but not actually in use
then the appropriate bit is set in ipi_resrv. If an interrupt is either
not reserved for use as an IPI or has been allocated as one then the
appropriate bit is clear in ipi_resrv.
Unfortunately this means that checking whether a bit is set in ipi_resrv
to prevent IPI interrupts being allocated for use with a device is
broken, because if the interrupt has been allocated as an IPI first then
its bit will be clear.
Fix this by separating the tracking of IPI reservation & usage,
introducing a separate ipi_available bitmap for the latter. This means
that ipi_resrv will now always have bits set corresponding to all
interrupts reserved for use as IPIs, whether or not they have been
allocated yet, and therefore that checking it when allocating device
interrupts works as expected.
Fixes: 2af70a9620 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: http://lkml.kernel.org/r/1492679256-14513-2-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Introduce support for registering an IPI IRQ domain suitable for use by
systems using the MIPS MT (multithreading) ASE within a single core.
This will allow for such systems to be supported generically, without
the current kludge of IPI code split between the MIPS arch & the malta
board support code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The various struct irq_chip callbacks in the MIPS CPU interrupt
controller driver have been calculating the hardware interrupt number by
subtracting MIPS_CPU_IRQ_BASE from the virq number. This presumes a
linear mapping beginning from MIPS_CPU_IRQ_BASE, and this will not hold
once an IPI IRQ domain is introduced. Switch to using the hwirq field of
struct irq_data which already contains the hardware interrupt number
instead of attempting to calculate it.
Similarly, plat_irq_dispatch calculated the virq number by adding
MIPS_CPU_IRQ_BASE to the hardware interrupt number. Ready this for the
introduction of an IPI IRQ domain by instead using irq_linear_revmap.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace use of the magic number 0x100 (ie. bit 8) with the more
explanatory IE_SW0 (ie. interrupt enable for software interrupt 0) or
C_SW0 (ie. cause bit for software interrupt 0) as appropriate.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15834/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Clear OF_POPULATED flag, so that GPC power domain driver[1] can be
bound to "gpc" node as well.
[1] https://lkml.org/lkml/2017/3/28/835
Cc: yurovsky@gmail.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On sama5d2, VDD core may be cut while suspending to RAM. This means the
AIC5 registers content is lost. Restore it at resume time.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In Mediatek SOCs, the CIRQ is a low power interrupt controller
designed to works outside MCUSYS which comprises with Cortex-Ax
cores,CCI and GIC.
The CIRQ controller is integrated in between MCUSYS( include
Cortex-Ax, CCI and GIC ) and interrupt sources as the second
level interrupt controller. The external interrupts which outside
MCUSYS will feed through CIRQ then bypass to GIC. CIRQ can monitors
all edge trigger interupts. When an edge interrupt is triggered,
CIRQ can record the status and generate a pulse signal to GIC when
flush command executed.
When system enters sleep mode, MCUSYS will be turned off to improve
power consumption, also GIC is power down. The edge trigger interrupts
will be lost in this scenario without CIRQ.
This commit provides the CIRQ irqchip implement.
Signed-off-by: Youlin Pei <youlin.pei@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Getting hold of the DevID requires us to call iort_pmsi_get_dev_id().
Since iort_pmsi_get_dev_id() may or may not be implemented, we
provide a weak function that acts as a stub.
The weak function will be removed when the ACPI counterpart is
merged.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
With the preparation of platform msi support and interrupt producer
in commit d44fa3d460 ("ACPI: Add support for ResourceSource/IRQ
domain mapping"), we can add mbigen ACPI support now.
Now that the major framework changes are ready, we just need to add
the ACPI probe code which creates the irqdomain for devices connecting
to it.
In order to create the irqdomain, we need to know the number of hw
irqs as input which is provided by mbigen. In DT case, we are using
"num-pins" property to describe it, and we will take advantage of
that too using _DSD in ACPI as there is no standard way of describe
it in ACPI way, also according to the _DSD rule described in
Documentation/acpi/DSD-properties-rules.txt, it doesn't break
the rules.
The DSDT is represented as below:
For mbigen,
Device(MBI0) {
Name(_HID, "HISI0152")
Name(_UID, Zero)
Name(_CRS, ResourceTemplate() {
Memory32Fixed(ReadWrite, 0xa0080000, 0x10000)
})
Name(_DSD, Package () {
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package () {
Package () {"num-pins", 378}
}
})
}
For devices,
Device(SAS0) {
Name(_HID, "HISIxxxx")
Name(_UID, Zero)
Name(_CRS, ResourceTemplate() {
Memory32Fixed(ReadWrite, 0xb0030000, 0x10000)
Interrupt(ResourceConsumer,..., "\_SB.MBI0") {12, ...}
})
}
So for the devices connected to the mbigen, as we clearly say that
it refers to a specific interrupt controller (mbigen), we can get
the virq from mbigen's irqdomain once it's created successfully.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: MaJun <majun258@huawei.com>
Cc: Al Stone <ahs3@redhat.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce mbigen_of_create_domain() to consolidate OF related
code and prepare for ACPI later, no funtional change.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Ma Jun <majun258@huawei.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Module owner will be set by driver core, so drop it.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Ma Jun <majun258@huawei.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
With the introduction of its_pmsi_init_one(), support for ACPI
firmware interface can be plugged into the gicv3 ITS driver.
Add code to scan the MADT table to get the ITS entry(ies), then use
the information to create the platform msi domain for devices
connected to it, mirroring the ITS PCI MSI code path.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce its_pmsi_init_one() to separate firmware dependent
code (ie OF dependent code) and firmware agnostic code so
that gic3-its code can be made to support other firmware
bindings easily.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
By adding ACPI support for platform MSI, the gicv3 driver has to
provide code to retrieve the dev id through ACPI instead of device
tree bindings; given that its_pmsi_prepare() allows already to get
the dev id but it is OF dependent, factor OF related code out into
a single function to make its_pmsi_prepare() ready to be used with
other firmware interfaces.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Rearrange header file includes in alphabetic order.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: fixed commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This prevent unnecessary visibility when configuring trigger type
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Originally driver only supports one base. However, MT6797 has
more than one bases to configure interrupt polarity. To support
possible design change, here comes a solution to use arbitrary
number of bases.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Moxa Art interrupt controller is very very likely just an instance
of the Faraday FTINTC010 interrupt controller from Faraday Technology.
An indication would be its close association with the FA526 ARM core
and the fact that the register layout is the same.
The implementation in irq-moxart.c can probably be right off replaced
with the irq-ftintc010.c driver by adding a compatible string, selecting
this irqchip from the machine and run.
As a bonus we have an irqchip driver supporting high/low and
rising/falling edges for the Moxa Art, and shared code with the Gemini
platform.
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The triggers in the driver were right for high level triggered
IRQs but the edge detection on edge triggered IRQs was wrong.
After studying a proper driver from Po-Yu Chuang I now know how
to handle these right, and we can properly implement low level
IRQs as well.
The device trees for the Gemini had polarity switched around
so these have been fixed to conform to the right polarity as
well.
Cc: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Gemini irqchip turns out to be a standard IP component from
Faraday Technology named FTINTC010 after some research and new
information.
- Rename the driver and all symbols to reflect the new information.
- Add the new compatible string "faraday,ftintc010"
- Create a Kconfig symbol CONFIG_FARADAY_FTINTC010 so that SoCs
using this interrupt controller can easily select and reuse it
instead of hardwiring it to ARCH_GEMINI
I have created a separate patch to select the new Kconfig symbol
from the Gemini machine, which will be merged through the ARM
SoC tree.
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 4cfffcfa51 ("irqchip/mips-gic: Fix local interrupts") added
mapping of several local interrupts during initialisation of the gic
driver. This associates virq numbers with these interrupts.
Unfortunately, as not all of the interrupts are mapped in hardware
order, when drivers subsequently request these interrupts they conflict
with the mappings that have already been set up. For example, this
manifests itself in the gic clocksource driver, which fails to probe
with the message:
clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0x7350c9738,
max_idle_ns: 440795203769 ns
GIC timer IRQ 25 setup failed: -22
This is because virq 25 (the correct IRQ number specified via device
tree) was allocated to the PERFCTR interrupt (and 24 to the timer, 26 to
the FDC). To fix this, map all of these local interrupts in the hardware
order so as to associate their virq numbers with the correct hw
interrupts.
Fixes: 4cfffcfa51 ("irqchip/mips-gic: Fix local interrupts")
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This driver uses the MSI domain but has no strict dependency on PCI_MSI, so we
may run into a build failure when CONFIG_GENERIC_MSI_IRQ_DOMAIN is disabled:
drivers/irqchip/irq-mvebu-odmi.c:152:15: error: variable 'odmi_msi_ops' has initializer but incomplete type
static struct msi_domain_ops odmi_msi_ops = {
^~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:155:15: error: variable 'odmi_msi_domain_info' has initializer but incomplete type
static struct msi_domain_info odmi_msi_domain_info = {
^~~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:3: error: 'struct msi_domain_info' has no member named 'flags'
.flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS),
^~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:12: error: 'MSI_FLAG_USE_DEF_DOM_OPS' undeclared here (not in a function)
.flags = (MSI_FLAG_USE_DEF_DOM_OPS | MSI_FLAG_USE_DEF_CHIP_OPS),
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/irqchip/irq-mvebu-odmi.c:156:39: error: 'MSI_FLAG_USE_DEF_CHIP_OPS' undeclared here (not in a function); did you mean 'MSI_FLAG_USE_DEF_DOM_OPS'?
Selecting the option from this driver seems to solve this nicely, though I could
not find any other instance of this in irqchip drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
- irqchip/crossbar: Some type tidying up
- irqchip/gicv3-its: Workaround for a Qualcomm erratum
- irqdomain: Compile for for systems that don't use CONFIG_IRQ_DOMAIN
-----BEGIN PGP SIGNATURE-----
iQFJBAABCAAzFiEEaVjJ8iM8Xp1syoGKqzCcdLk7HqEFAljBLCQVHG1hcmMuenlu
Z2llckBhcm0uY29tAAoJEKswnHS5Ox6h6h8IAJKt0NHSLV4vQH51MdX1flj8uyw0
xzeosx/r7hsV/apbaFcciJuaOZNDYdVH+a1NboklpDe2g8N1eSwSITodXnsg3seO
1EyGWkZT9lWbz8/febvG8WPLLZJu0CeD9wNRT7cePTUgNZgGRR1IN6ySM/TtWixA
csIL9kgdRvChcU6hydTPceBzN5pSpZ169+BTeEL5CVTggRiq24fJlmBwM7caOu1Z
nZDsKckUQA5D/VO0CiopE6BpCZTBzB6TTC2251DEEfVxyL6/M947lOtsC4EXK4y2
6CjWM4II24ImvPmqYDNIwzK1ZimhWO0Uo8jy1LZZKVpiXXXk8zm6LKxqJbU=
=JV9b
-----END PGP SIGNATURE-----
Merge tag 'irq-fixes-4.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip/irqdomain updates for 4.11-rc2 from Marc Zyngier
- irqchip/crossbar: Some type tidying up
- irqchip/gicv3-its: Workaround for a Qualcomm erratum
- irqdomain: Compile for for systems that don't use CONFIG_IRQ_DOMAIN
Fixed up minor conflict in the crossbar driver.
The 'size' variable is unsigned according to the dt-bindings.
As this variable is used as integer in other places, create a new variable
that allows to fix the following sparse issue (-Wtypesign):
drivers/irqchip/irq-crossbar.c:279:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:279:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:279:52: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
On Qualcomm Datacenter Technologies QDF2400 SoCs, the ITS hardware
implementation uses 16Bytes for Interrupt Translation Entry (ITE),
but reports an incorrect value of 8Bytes in GITS_TYPER.ITTE_size.
It might cause kernel memory corruption depending on the number
of MSI(x) that are configured and the amount of memory that has
been allocated for ITEs in its_create_device().
This patch fixes the potential memory corruption by setting the
correct ITE size to 16Bytes.
Cc: stable@vger.kernel.org
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The max and entry variables are unsigned according to the dt-bindings.
Fix following 3 sparse issues (-Wtypesign):
drivers/irqchip/irq-crossbar.c:222:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:222:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:222:52: got int *<noident>
drivers/irqchip/irq-crossbar.c:245:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:245:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:245:56: got int *<noident>
drivers/irqchip/irq-crossbar.c:263:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:263:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:263:56: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The max and entry variables are unsigned according to the dt-bindings.
Fix following 3 sparse issues (-Wtypesign):
drivers/irqchip/irq-crossbar.c:222:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:222:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:222:52: got int *<noident>
drivers/irqchip/irq-crossbar.c:245:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:245:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:245:56: got int *<noident>
drivers/irqchip/irq-crossbar.c:263:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:263:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:263:56: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Cc: marc.zyngier@arm.com
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/20170223094855.6546-1-fdemathieu@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The changes include:
* KVM PCIe/MSI passthrough support on ARM/ARM64
* Introduction of a core representation for individual hardware
iommus
* Support for IOMMU privileged mappings as supported by some
ARM IOMMUS
* 16-bit SID support for ARM-SMMUv2
* Stream table optimization for ARM-SMMUv3
* Various fixes and other small improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5b3I
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU UPDATES from Joerg Roedel:
- KVM PCIe/MSI passthrough support on ARM/ARM64
- introduction of a core representation for individual hardware iommus
- support for IOMMU privileged mappings as supported by some ARM IOMMUS
- 16-bit SID support for ARM-SMMUv2
- stream table optimization for ARM-SMMUv3
- various fixes and other small improvements
* tag 'iommu-updates-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (61 commits)
vfio/type1: Fix error return code in vfio_iommu_type1_attach_group()
iommu: Remove iommu_register_instance interface
iommu/exynos: Make use of iommu_device_register interface
iommu/mediatek: Make use of iommu_device_register interface
iommu/msm: Make use of iommu_device_register interface
iommu/arm-smmu: Make use of the iommu_register interface
iommu: Add iommu_device_set_fwnode() interface
iommu: Make iommu_device_link/unlink take a struct iommu_device
iommu: Add sysfs bindings for struct iommu_device
iommu: Introduce new 'struct iommu_device'
iommu: Rename struct iommu_device
iommu: Rename iommu_get_instance()
iommu: Fix static checker warning in iommu_insert_device_resv_regions
iommu: Avoid unnecessary assignment of dev->iommu_fwspec
iommu/mediatek: Remove bogus 'select' statements
iommu/dma: Remove bogus dma_supported() implementation
iommu/ipmmu-vmsa: Restrict IOMMU Domain Geometry to 32-bit address space
iommu/vt-d: Don't over-free page table directories
iommu/vt-d: Tylersburg isoch identity map check is done too late.
iommu/vt-d: Fix some macros that are incorrectly specified in intel-iommu
...
Pull irq updates from Thomas Gleixner:
"This update provides:
- Yet another two irq controller chip drivers
- A few updates and fixes for GICV3
- A resource managed function for interrupt allocation
- Fixes, updates and enhancements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/qcom: Fix error handling
genirq: Clarify logic calculating bogus irqreturn_t values
genirq/msi: Add stubs for get_cached_msi_msg/pci_write_msi_msg
genirq/devres: Use dev_name(dev) as default for devname
genirq: Fix /proc/interrupts output alignment
irqdesc: Add a resource managed version of irq_alloc_descs()
irqchip/gic-v3-its: Zero command on allocation
irqchip/gic-v3-its: Fix command buffer allocation
irqchip/mips-gic: Fix local interrupts
irqchip: Add a driver for Cortina Gemini
irqchip: DT bindings for Cortina Gemini irqchip
irqchip/gic-v3: Remove duplicate definition of GICD_TYPER_LPIS
irqchip/gic-v3-its: Rename MAPVI to MAPTI
irqchip/gic-v3-its: Drop deprecated GITS_BASER_TYPE_CPU
irqchip/gic-v3-its: Refactor command encoding
irqchip/gic-v3-its: Enable cacheable attribute Read-allocate hints
irqchip/qcom: Add IRQ combiner driver
ACPI: Add support for ResourceSource/IRQ domain mapping
ACPI: Generic GSI: Do not attempt to map non-GSI IRQs during bus scan
irq/platform-msi: Fix comment about maximal MSIs
When reusing commands from the ring buffer, it would be better
to zero them out, even if the ITS should ignore the unused
fields.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The its command buffer must be page aligned, but kzalloc() is not
guaranteed to be (though it is mostly when allocating 64k). Use
__get_free_pages() as this is used for other buffers as well.
Signed-off-by: Robert Richter <rrichter@cavium.com>
[Marc: fixed the error path]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Some local interrupts are not initialised properly at the moment and
cannot be used since the domain's alloc method is never called for them.
This has been observed earlier and partially fixed in commit
e875bd66df ("irqchip/mips-gic: Fix local interrupts"), but that change
still relied on the interrupt to be requested by an external driver (eg.
drivers/clocksource/mips-gic-timer.c).
This does however not solve the issue for interrupts that are not
referenced by any driver through the device tree and results in
request_irq() calls returning -ENOSYS. It can be observed when attempting
to use perf tool to access hardware performance counters.
Fix this by explicitly calling irq_create_fwspec_mapping() for local
interrupts.
Fixes: e875bd66df ("irqchip/mips-gic: Fix local interrupts")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
As a part of transitioning the Gemini platform to device tree we
create this clean, device-tree-only irqchip driver.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Back in the days when the GICv3/v4 architecture was drafted,
the command to an event to an LPI number was called MAPVI.
Later on, and to avoid confusion with the GICv4 command VMAPI,
it was renamed MAPTI. We've carried the old name for a long
time, but it gets in the way of people reading the code in
the light of the public architecture specification.
Just repaint all the references and kill the old definition.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
During the development of the GICv3/v4 architecture, it was
envisaged to have a CPU table, though the use for it was
never completely clear (the collection table serves that role
pretty well). It ended being dropped before the specification
was published, though it lived on in the driver.
In order to avoid people scratching their head too much, let's do
the same in the kernel.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The way we encode the various ITS command fields is both tedious
and error prone. Let's introduce a helper function that performs
the encoding, and convert the existing encoders to use that
helper. It also has the advantage of expressing the encoding in
a way that matches the architecture specification.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Read-allocation hints are not enabled for both the GIC-ITS and GICR
tables. This forces the hardware to always read the table contents
from an external memory (DDR) which is slow compared to cache memory.
Most of the tables are often read by hardware. So, it's better to
enable Read-allocate hints in addition to Write-allocate hints in
order to improve the GICR_PEND, GICR_PROP, Collection, Device, and
vCPU tables lookup time.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Driver for interrupt combiners in the Top-level Control and Status
Registers (TCSR) hardware block in Qualcomm Technologies chips.
An interrupt combiner in this block combines a set of interrupts by
OR'ing the individual interrupt signals into a summary interrupt
signal routed to a parent interrupt controller, and provides read-
only, 32-bit registers to query the status of individual interrupts.
The status bit for IRQ n is bit (n % 32) within register (n / 32)
of the given combiner. Thus, each combiner can be described as a set
of register offsets and the number of IRQs managed.
Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
