* pci/endpoint:
tools: PCI: Add a missing option help line
misc: pci_endpoint_test: Enable/Disable MSI using module param
misc: pci_endpoint_test: Avoid using hard-coded BAR sizes
misc: pci_endpoint_test: Add support to not enable MSI interrupts
misc: pci_endpoint_test: Add support to provide aligned buffer addresses
misc: pci_endpoint_test: Add support for PCI_ENDPOINT_TEST regs to be mapped to any BAR
PCI: designware-ep: Do not disable BARs during initialization
PCI: dra7xx: Reset all BARs during initialization
PCI: dwc: designware: Provide page_size to pci_epc_mem
PCI: endpoint: Remove the ->remove() callback
PCI: endpoint: Add support to poll early for host commands
PCI: endpoint: Add support to use _any_ BAR to map PCI_ENDPOINT_TEST regs
PCI: endpoint: Do not reset *command* inadvertently
PCI: endpoint: Add "volatile" to pci_epf_test_reg
PCI: endpoint: Add support for configurable page size
PCI: endpoint: Make ->remove() callback optional
PCI: endpoint: Add an API to get matching "pci_epf_device_id"
PCI: endpoint: Use of_dma_configure() to set initial DMA mask
The read-only DBI registers can be written only when the "Write to RO
Registers Using DBI" (DBI_RO_WR_EN) field of MISC_CONTROL_1_OFF is set.
Add accessors to enable and disable write permission, and use them instead
of accessing MISC_CONTROL_1_OFF directly.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Use the newly introduced __pci_epc_mem_init() instead of pci_epc_mem_init()
to provide page_size to pci_epc_mem. This is in preparation for
adding EP support to K2G which has a restriction that the
address region should be either divided into 1MB/2MB/4MB or 8MB
sizes (Ref: 11.14.4.9.1 Outbound Address Translation in K2G TRM SPRUHY8F
January 2016 – Revised May 2017).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In several dwc-based drivers, ->host_init() can fail, so make sure to
propagate and handle this to avoid continuing operation of a driver or
hardware in an invalid state.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
The dw_pcie_host_ops structures are never modified. Constify these
structures such that these can be write-protected.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The PCIe controller integrated in dra7xx SoCs is capable of operating in
endpoint mode. Add endpoint mode support to dra7xx driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add endpoint mode support to designware driver. This uses the EP Core layer
introduced recently to add endpoint mode support. *Any* function driver
can now use this designware device in order to achieve the EP
functionality.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously dbi accessors can be used to access data of size 4 bytes. But
there might be situations (like accessing MSI_MESSAGE_CONTROL in order to
set/get the number of required MSI interrupts in EP mode) where dbi
accessors must be used to access data of size 2. This is in preparation
for adding endpoint mode support to designware driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Cassel <niklas.cassel@axis.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Joao Pinto <Joao.Pinto@synopsys.com>
dwc has 2 dbi address space labeled dbics and dbics2. The existing helper
to access dbi address space can access only dbics. However dbics2 has to
be accessed for programming the BAR registers in the case of EP mode. This
is in preparation for adding EP mode support to dwc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Cassel <niklas.cassel@axis.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Joao Pinto <Joao.Pinto@synopsys.com>
Some platforms (like dra7xx) require only the least 28 bits of the
corresponding 32 bit CPU address to be programmed in the address
translation unit. This modified address is stored in io_base/mem_base/
cfg0_base/cfg1_base in dra7xx_pcie_host_init(). While this is okay for
host mode where the address range is fixed, device mode requires different
addresses to be programmed based on the host buffer address. Add a new
ops to get the least 28 bits of the corresponding 32 bit CPU address and
invoke it before programming the address translation unit.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joao Pinto <jpinto@synopsys.com>
Now that PCI designware host has a separate file, add a new PCIE_DW_HOST
config symbol to select the host-only driver. This will enable to
independently select host support and endpoint support (when it's added).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Split pcie-designware.c into pcie-designware-host.c that contains the host
specific parts of the driver and pcie-designware.c that contains the parts
used by both host driver and endpoint driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "num-lanes" DT property is parsed in dw_pcie_host_init(). However
num-lanes is applicable to both root complex mode and endpoint mode. As a
first step, move the parsing of this property outside dw_pcie_host_init().
This is in preparation for splitting pcie-designware.c to pcie-designware.c
and pcie-designware-host.c
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Keep only the host-specific members in struct pcie_port and move the common
members (i.e common to both host and endpoint) to struct dw_pcie. This is
in preparation for adding endpoint mode support to designware driver.
While at that also fix checkpatch warnings.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Richard Zhu <hongxing.zhu@nxp.com>
CC: Lucas Stach <l.stach@pengutronix.de>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Minghuan Lian <minghuan.Lian@freescale.com>
CC: Mingkai Hu <mingkai.hu@freescale.com>
CC: Roy Zang <tie-fei.zang@freescale.com>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Niklas Cassel <niklas.cassel@axis.com>
CC: Jesper Nilsson <jesper.nilsson@axis.com>
CC: Joao Pinto <Joao.Pinto@synopsys.com>
CC: Zhou Wang <wangzhou1@hisilicon.com>
CC: Gabriele Paoloni <gabriele.paoloni@huawei.com>
CC: Stanimir Varbanov <svarbanov@mm-sol.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
No functional change. dw_pcie_cfg_read()/dw_pcie_cfg_write() doesn't do
anything specific to access configuration space. It can be just renamed to
dw_pcie_read()/dw_pcie_write() and used to read/write data to dbi space.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Joao Pinto <jpinto@synopsys.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Stanimir Varbanov <svarbanov@mm-sol.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
No functional change. Move the register defines and other macros from
pcie-designware.c to pcie-designware.h. This is in preparation to split the
pcie-designware.c file into designware core file and host-specific file.
While at that also fix a checkpatch warning.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-By: Joao Pinto <jpinto@synopsys.com>
Group all the PCI drivers that use DesignWare core in dwc directory.
dwc IP is capable of operating in both host mode and device mode and
keeping it inside the *host* directory is misleading.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Minghuan Lian <minghuan.Lian@freescale.com>
Cc: Mingkai Hu <mingkai.hu@freescale.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
