None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes an erroneous check of CSIZE, which made it impossible to set
CS5.
Compiles clean, but couldn't test against hardware.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port drain delay is constant and should be set at port probe rather
than open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use uninitialised termios data to determine when to configure the
device at open.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fetch modem status on carrier_raised and tiocmget.
This driver appeared to support modem-status but only read the modem
status registers once at open and then used that cached value for all
further enquires.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reimplement device type detection using the device id table and quirks.
Device type was used to detect one device type which did not support to
control functions. Add quirks to the device table and store them in the
private port data at probe instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass usb-serial port to the control functions for uart status and work
mode.
Use port device for debugging and use dev_err to report errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken uart-error handling.
This driver appears to implement uart-error handling but does not
receive status interrupts or status information with bulk in transfers.
Instead status was retrieved at open and used to flag only the first
bulk in transfer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove broken TIOCMIWAIT support.
This drivers appears to implement TIOCMIWAIT but has no means of
receiving modem-status interrupts.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port wait queue and make sure to check the serial disconnected
flag before accessing private port data after waking up.
This is is needed as the private port data (including the wait queue
itself) can be gone when waking up after a disconnect.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Now 4 string flipping ones are on turn:
* tty_insert_flip_string_flags
* tty_insert_flip_string_fixed_flag
* tty_prepare_flip_string
* tty_prepare_flip_string_flags
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove all MODULE_VERSION macros and driver-version information (except
for garmin_gps which uses it in a status reply).
It is the kernel version that matters and not some private version
scheme which rarely even gets updated.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak by replacing attach and release with
port_probe and port_remove.
Since commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) the port private data is no longer freed at release as
it is no longer accessible.
Compile-only tested.
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big USB pull request for 3.7-rc1
There are lots of gadget driver changes (including copying a bunch of
files into the drivers/staging/ccg/ directory so that the other gadget
drivers can be fixed up properly without breaking that driver), and we
remove the old obsolete ub.c driver from the tree. There are also the
usual XHCI set of updates, and other various driver changes and updates.
We also are trying hard to remove the old dbg() macro, but the final
bits of that removal will be coming in through the networking tree
before we can delete it for good.
All of these patches have been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3+AACgkQMUfUDdst+ym5vwCfe93FyJyXn/RDkGz7iBemvWFd
vrwAoIxjaOa4/yWZWcgrWc5bP4aO3ssc
=jYDr
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB changes from Greg Kroah-Hartman:
"Here is the big USB pull request for 3.7-rc1
There are lots of gadget driver changes (including copying a bunch of
files into the drivers/staging/ccg/ directory so that the other gadget
drivers can be fixed up properly without breaking that driver), and we
remove the old obsolete ub.c driver from the tree.
There are also the usual XHCI set of updates, and other various driver
changes and updates. We also are trying hard to remove the old dbg()
macro, but the final bits of that removal will be coming in through
the networking tree before we can delete it for good.
All of these patches have been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up several annoying - but fairly mindless - conflicts due to the
termios structure having moved into the tty device, and often clashing
with dbg -> dev_dbg conversion.
* tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (339 commits)
USB: ezusb: move ezusb.c from drivers/usb/serial to drivers/usb/misc
USB: uas: fix gcc warning
USB: uas: fix locking
USB: Fix race condition when removing host controllers
USB: uas: add locking
USB: uas: fix abort
USB: uas: remove aborted field, replace with status bit.
USB: uas: fix task management
USB: uas: keep track of command urbs
xhci: Intel Panther Point BEI quirk.
powerpc/usb: remove checking PHY_CLK_VALID for UTMI PHY
USB: ftdi_sio: add TIAO USB Multi-Protocol Adapter (TUMPA) support
Revert "usb : Add sysfs files to control port power."
USB: serial: remove vizzini driver
usb: host: xhci: Fix Null pointer dereferencing with 71c731a for non-x86 systems
Increase XHCI suspend timeout to 16ms
USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq
USB: sierra_ms: don't keep unused variable
fsl/usb: Add support for USB controller version 2.4
USB: qcaux: add Pantech vendor class match
...
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will let us sort out a whole pile of tty related races. The
alternative would be to keep points and refcount the termios objects.
However
1. They are tiny anyway
2. Many devices don't use the stored copies
3. We can remove a pty special case
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() is a usb-serial specific macro. This patch converts
the spcp8x5.c driver to use dev_dbg() instead to tie into the
dynamic debug infrastructure.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reworks the usb_serial_register_drivers() and
usb_serial_deregister_drivers() to not need a pointer to a struct
usb_driver anymore. The usb_driver structure is now created dynamically
and registered and unregistered as needed.
This saves lines of code in each usb-serial driver. All in-kernel users
of these functions were also fixed up at this time. The pl2303 driver
was tested that everything worked properly.
Thanks for the idea to do this from Alan Stern.
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Donald Lee <donald@asix.com.tw>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Michal Sroczynski <msroczyn@gmail.com>
Cc: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Preston Fick <preston.fick@silabs.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Rigbert Hamisch <rigbert@gmx.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Support Department <support@connecttech.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: Wang YanQing <Udknight@gmail.com>
Cc: William Greathouse <wgreathouse@smva.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now set by the usb-serial core, no need for the driver to
individually set it.
Thanks to Alan Stern for the idea to get rid of it.
Cc: William Greathouse <wgreathouse@smva.com>
Cc: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Support Department <support@connecttech.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Preston Fick <preston.fick@silabs.com>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Donald Lee <donald@asix.com.tw>
Cc: Julia Lawall <julia@diku.dk>
Cc: Michal Sroczynski <msroczyn@gmail.com>
Cc: Wang YanQing <Udknight@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Cc: Rigbert Hamisch <rigbert@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now set by the usb-serial core, no need for the driver to
individually set it.
Thanks to Alan Stern for the idea to get rid of it.
Cc: William Greathouse <wgreathouse@smva.com>
Cc: Matthias Bruestle and Harald Welte <support@reiner-sct.com>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Support Department <support@connecttech.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Preston Fick <preston.fick@silabs.com>
Cc: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Cc: Simon Arlott <simon@fire.lp0.eu>
Cc: Andrew Worsley <amworsley@gmail.com>
Cc: "Michał Wróbel" <michal.wrobel@flytronic.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Aleksey Babahin <tamerlan311@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Donald Lee <donald@asix.com.tw>
Cc: Julia Lawall <julia@diku.dk>
Cc: Michal Sroczynski <msroczyn@gmail.com>
Cc: Wang YanQing <Udknight@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Cc: Rigbert Hamisch <rigbert@gmx.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Jesper Juhl <jj@chaosbits.net>
Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was used a lot a long time ago to trace code flow. Now that we have
ftrace, this isn't needed at all, so remove these calls.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the spcp8x5.c driver to use the module_usb_serial_driver() call
instead of having to have a module_init/module_exit function, saving a lot
of duplicated code.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1528) modifies the following usb-serial drivers to
utilize the new usb_serial_{de}register_drivers() routines:
qcaux, qcserial, safe_serial, siemens_mpi, sierra,
spcp8x5, ssu100, and symbolserial.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We don't use it so we can trim it from here as we try and stamp the file
object dependencies out of the serial code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan's commit 335f8514f2 introduced
.carrier_raised function in several drivers. That also means
tty_port_block_til_ready can now suspend the process trying to open the serial
port when Carrier Detect is low and put it into tty_port.open_wait queue. We
need to wake up the process when Carrier Detect goes high and trigger TTY
hangup when CD goes low.
Some of the devices do not report modem status line changes, or at least we
don't understand the status message, so for those we remove .carrier_raised
again.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1443) fixes a bug found in many of the USB serial
drivers: They don't set the .usb_driver field in their
usb_serial_driver structure. This field is needed for assigning
dynamic IDs for device matching.
In addition, starting with the 2.6.37 kernel, the .usb_driver field is
needed for proper autosuspend operation. Without it, attempts to open
the device file will fail.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Williams <dcbw@redhat.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg prefers this to go through the trivial tree.
http://lkml.org/lkml/2010/6/24/1
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Moved a statement down a line in drivers/usb/host/u132-hcd.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix regression introduced by commit
a108bfcb37 (USB: tty: Prune uses of
tty_request_room in the USB layer) which broke three drivers
(cypress_m8, digi_acceleport and spcp8x5) through incorrect use of
tty_insert_flip_string_fixed_flag.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1344) removes references to port->port.count from the
USB serial drivers. Now that serial ports are properly reference
counted, port.count checking is unnecessary and incorrect. Drivers
should assume that the port is in use from the time the open method
runs until the close method is called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have lots of callers that do not need to do this in the first place.
Remove the calls as they both cost CPU and for big buffers can mess up the
multi-page allocation avoidance.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various drivers have hacks to mangle termios structures. This stems from
the fact there is no nice setup hook for configuring the termios settings
when the port is created
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And indeed none of them use it. Clean this up as it will make moving to a
standard open method rather easier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1254) splits up the shutdown method of usb_serial_driver
into a disconnect and a release method.
The problem is that the usb-serial core was calling shutdown during
disconnect handling, but drivers didn't expect it to be called until
after all the open file references had been closed. The result was an
oops when the close method tried to use memory that had been
deallocated by shutdown.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the usb-serial drivers are starting to use urb->status in ways
they should not be doing. This fixes up some of them to prevent that.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kref in the USB serial drivers so that we don't free tty structures
from under the URB receive handlers as has historically been the case if
you were unlucky. This also gives us a framework for general tty drivers to
use tty_port objects and refcount.
Contains two err->dev_err changes merged together to fix clashes in the
-next tree.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
