Detect and recover from machine check when inside opal on a special
scom load instructions. On specific SCOM read via MMIO we may get a machine
check exception with SRR0 pointing inside opal. To recover from MC
in this scenario, get a recovery instruction address and return to it from
MC.
OPAL will export the machine check recoverable ranges through
device tree node mcheck-recoverable-ranges under ibm,opal:
# hexdump /proc/device-tree/ibm,opal/mcheck-recoverable-ranges
0000000 0000 0000 3000 2804 0000 000c 0000 0000
0000010 3000 2814 0000 0000 3000 27f0 0000 000c
0000020 0000 0000 3000 2814 xxxx xxxx xxxx xxxx
0000030 llll llll yyyy yyyy yyyy yyyy
...
...
#
where:
xxxx xxxx xxxx xxxx = Starting instruction address
llll llll = Length of the address range.
yyyy yyyy yyyy yyyy = recovery address
Each recoverable address range entry is (start address, len,
recovery address), 2 cells each for start and recovery address, 1 cell for
len, totalling 5 cells per entry. During kernel boot time, build up the
recovery table with the list of recovery ranges from device-tree node which
will be used during machine check exception to recover from MMIO SCOM UE.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The OPAL firmware functions opal_xscom_read and opal_xscom_write
take a 64-bit argument for the XSCOM (PCB) address in order to
support the indirect mode on P8.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.13]
The new ELFv2 little-endian ABI increases the stack redzone -- the
area below the stack pointer that can be used for storing data --
from 288 bytes to 512 bytes. This means that we need to allow more
space on the user stack when delivering a signal to a 64-bit process.
To make the code a bit clearer, we define new USER_REDZONE_SIZE and
KERNEL_REDZONE_SIZE symbols in ptrace.h. For now, we leave the
kernel redzone size at 288 bytes, since increasing it to 512 bytes
would increase the size of interrupt stack frames correspondingly.
Gcc currently only makes use of 288 bytes of redzone even when
compiling for the new little-endian ABI, and the kernel cannot
currently be compiled with the new ABI anyway.
In the future, hopefully gcc will provide an option to control the
amount of redzone used, and then we could reduce it even more.
This also changes the code in arch_compat_alloc_user_space() to
preserve the expanded redzone. It is not clear why this function would
ever be used on a 64-bit process, though.
Signed-off-by: Paul Mackerras <paulus@samba.org>
CC: <stable@vger.kernel.org> [v3.13]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch cleans up variable eeh_subsystem_enabled so that we needn't
refer the variable directly from external. Instead, we will use
function eeh_enabled() and eeh_set_enable() to operate the variable.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
perf is failing to resolve symbols in the VDSO. A while (1)
gettimeofday() loop shows:
93.99% [vdso] [.] 0x00000000000005e0
3.12% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.81% test [.] main
The reason for this is that we are linking our VDSO shared libraries
at 1MB, which is a little weird. Even though this is uncommon, Alan
points out that it is valid and we should probably fix perf userspace.
Regardless, I can't see a reason why we are doing this. The code
is all position independent and we never rely on the VDSO ending
up at 1M (and we never place it there on 64bit tasks).
Changing our link address to 0x0 fixes perf VDSO symbol resolution:
73.18% [vdso] [.] 0x000000000000060c
12.39% [vdso] [.] __kernel_gettimeofday
3.58% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.94% [vdso] [.] __kernel_datapage_offset
2.90% test [.] main
We still have some local symbol resolution issues that will be
fixed in a subsequent patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Archs like ppc64 doesn't do tlb flush in set_pte/pmd functions when using
a hash table MMU for various reasons (the flush is handled as part of
the PTE modification when necessary).
ppc64 thus doesn't implement flush_tlb_range for hash based MMUs.
Additionally ppc64 require the tlb flushing to be batched within ptl locks.
The reason to do that is to ensure that the hash page table is in sync with
linux page table.
We track the hpte index in linux pte and if we clear them without flushing
hash and drop the ptl lock, we can have another cpu update the pte and can
end up with duplicate entry in the hash table, which is fatal.
We also want to keep set_pte_at simpler by not requiring them to do hash
flush for performance reason. We do that by assuming that set_pte_at() is
never *ever* called on a PTE that is already valid.
This was the case until the NUMA code went in which broke that assumption.
Fix that by introducing a new pair of helpers to set _PAGE_NUMA in a
way similar to ptep/pmdp_set_wrprotect(), with a generic implementation
using set_pte_at() and a powerpc specific one using the appropriate
mechanism needed to keep the hash table in sync.
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pte_update() is a powerpc-ism used to change the bits of a PTE
when the access permission is being restricted (a flush is
potentially needed).
It uses atomic operations on when needed and handles the hash
synchronization on hash based processors.
It is currently only used to clear PTE bits and so the current
implementation doesn't provide a way to also set PTE bits.
The new _PAGE_NUMA bit, when set, is actually restricting access
so it must use that function too, so this change adds the ability
for pte_update() to also set bits.
We will use this later to set the _PAGE_NUMA bit.
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the support for to create a direct iommu "bypass"
window on IODA2 bridges (such as Power8) allowing to bypass iommu
page translation completely for 64-bit DMA capable devices, thus
significantly improving DMA performances.
Additionally, this adds a hook to the struct iommu_table so that
the IOMMU API / VFIO can disable the bypass when external ownership
is requested, since in that case, the device will be used by an
environment such as userspace or a KVM guest which must not be
allowed to bypass translations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On p8 systems, with relocation on exception feature enabled we are seeing
kdump kernel hang at interrupt vector 0xc*4400. The reason is, with this
feature enabled, exception are raised with MMU (IR=DR=1) ON with the
default offset of 0xc*4000. Since exception is raised in virtual mode it
requires the vector region to be executable without which it fails to
fetch and execute instruction at 0xc*4xxx. For default kernel since kernel
is loaded at real 0, the htab mappings sets the entire kernel text region
executable. But for relocatable kernel (e.g. kdump case) we only copy
interrupt vectors down to real 0 and never marked that region as
executable because in p7 and below we always get exception in real mode.
This patch fixes this issue by marking htab mapping range as executable
that overlaps with the interrupt vector region for relocatable kernel.
Thanks to Ben who helped me to debug this issue and find the root cause.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
two s390 guest features that need some handling in the host,
and all the PPC changes. The PPC changes include support for
little-endian guests and enablement for new POWER8 features.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=yd0Z
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"Second batch of KVM updates. Some minor x86 fixes, two s390 guest
features that need some handling in the host, and all the PPC changes.
The PPC changes include support for little-endian guests and
enablement for new POWER8 features"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (45 commits)
x86, kvm: correctly access the KVM_CPUID_FEATURES leaf at 0x40000101
x86, kvm: cache the base of the KVM cpuid leaves
kvm: x86: move KVM_CAP_HYPERV_TIME outside #ifdef
KVM: PPC: Book3S PR: Cope with doorbell interrupts
KVM: PPC: Book3S HV: Add software abort codes for transactional memory
KVM: PPC: Book3S HV: Add new state for transactional memory
powerpc/Kconfig: Make TM select VSX and VMX
KVM: PPC: Book3S HV: Basic little-endian guest support
KVM: PPC: Book3S HV: Add support for DABRX register on POWER7
KVM: PPC: Book3S HV: Prepare for host using hypervisor doorbells
KVM: PPC: Book3S HV: Handle new LPCR bits on POWER8
KVM: PPC: Book3S HV: Handle guest using doorbells for IPIs
KVM: PPC: Book3S HV: Consolidate code that checks reason for wake from nap
KVM: PPC: Book3S HV: Implement architecture compatibility modes for POWER8
KVM: PPC: Book3S HV: Add handler for HV facility unavailable
KVM: PPC: Book3S HV: Flush the correct number of TLB sets on POWER8
KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs
KVM: PPC: Book3S HV: Align physical and virtual CPU thread numbers
KVM: PPC: Book3S HV: Don't set DABR on POWER8
kvm/ppc: IRQ disabling cleanup
...
smt-snooze-delay was designed to disable NAP state or delay the entry
to the NAP state prior to adoption of cpuidle framework. This
is per-cpu variable. With the coming of CPUIDLE framework,
states can be disabled on per-cpu basis using the cpuidle/enable
sysfs entry.
Also, with the coming of cpuidle driver each state's target residency
is per-driver unlike earlier which was per-device. Therefore,
the per-cpu sysfs smt-snooze-delay which decides the target residency
of the idle state on a particular cpu causes more confusion to the user
as we cannot have different smt-snooze-delay (target residency)
values for each cpu.
In the current code, smt-snooze-delay functionality is completely broken.
It makes sense to remove smt-snooze-delay from idle driver with the
coming of cpuidle framework.
However, sysfs files are retained as ppc64_util currently
utilises it. Once we fix ppc64_util, propose to clean
up the kernel code.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move the file from arch specific pseries/processor_idle.c
to drivers/cpuidle/cpuidle-pseries.c
Make the relevant Makefile and Kconfig changes.
Also, introduce Kconfig.powerpc in drivers/cpuidle
for all powerpc cpuidle drivers.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It seems that forward declaration couldn't work well with typedef, use
struct spinlock directly to avoiding following build errors:
In file included from include/linux/spinlock.h:81,
from include/linux/seqlock.h:35,
from include/linux/time.h:5,
from include/uapi/linux/timex.h:56,
from include/linux/timex.h:56,
from include/linux/sched.h:17,
from arch/powerpc/kernel/asm-offsets.c:17:
include/linux/spinlock_types.h:76: error: redefinition of typedef 'spinlock_t'
/root/linux-next/arch/powerpc/include/asm/pgtable-ppc64.h:563: note: previous declaration of 'spinlock_t' was here
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
Pull powerpc mremap fix from Ben Herrenschmidt:
"This is the patch that I had sent after -rc8 and which we decided to
wait before merging. It's based on a different tree than my -next
branch (it needs some pre-reqs that were in -rc4 or so while my -next
is based on -rc1) so I left it as a separate branch for your to pull.
It's identical to the request I did 2 or 3 weeks back.
This fixes crashes in mremap with THP on powerpc.
The fix however requires a small change in the generic code. It moves
a condition into a helper we can override from the arch which is
harmless, but it *also* slightly changes the order of the set_pmd and
the withdraw & deposit, which should be fine according to Kirill (who
wrote that code) but I agree -rc8 is a bit late...
It was acked by Kirill and Andrew told me to just merge it via powerpc"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/thp: Fix crash on mremap
At a glance these are just the inverse of each other. The one subtlety
is that arch_spin_value_unlocked() takes the lock by value, rather than
as a pointer, which is important for the lockref code.
On the other hand arch_spin_is_locked() doesn't really care, so
implement it in terms of arch_spin_value_unlocked().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This commit adds the architecture support required to enable the
optimised implementation of lockrefs.
That's as simple as defining arch_spin_value_unlocked() and selecting
the Kconfig option.
We also define cmpxchg64_relaxed(), because the lockref code does not
need the cmpxchg to have barrier semantics.
Using Linus' test case[1] on one system I see a 4x improvement for the
basic enablement, and a further 1.3x for cmpxchg64_relaxed(), for a
total of 5.3x vs the baseline.
On another system I see more like 2x improvement.
[1]: http://marc.info/?l=linux-fsdevel&m=137782380714721&w=4
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the software abort code defines for transactional memory (TM).
These values are from PAPR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add new state for transactional memory (TM) to kvm_vcpu_arch. Also add
asm-offset bits that are going to be required.
This also moves the existing TFHAR, TFIAR and TEXASR SPRs into a
CONFIG_PPC_TRANSACTIONAL_MEM section. This requires some code changes to
ensure we still compile with CONFIG_PPC_TRANSACTIONAL_MEM=N. Much of the added
the added #ifdefs are removed in a later patch when the bulk of the TM code is
added.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix merge conflict]
Signed-off-by: Alexander Graf <agraf@suse.de>
We create a guest MSR from scratch when delivering exceptions in
a few places. Instead of extracting LPCR[ILE] and inserting it
into MSR_LE each time, we simply create a new variable intr_msr which
contains the entire MSR to use. For a little-endian guest, userspace
needs to set the ILE (interrupt little-endian) bit in the LPCR for
each vcpu (or at least one vcpu in each virtual core).
[paulus@samba.org - removed H_SET_MODE implementation from original
version of the patch, and made kvmppc_set_lpcr update vcpu->arch.intr_msr.]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The DABRX (DABR extension) register on POWER7 processors provides finer
control over which accesses cause a data breakpoint interrupt. It
contains 3 bits which indicate whether to enable accesses in user,
kernel and hypervisor modes respectively to cause data breakpoint
interrupts, plus one bit that enables both real mode and virtual mode
accesses to cause interrupts. Currently, KVM sets DABRX to allow
both kernel and user accesses to cause interrupts while in the guest.
This adds support for the guest to specify other values for DABRX.
PAPR defines a H_SET_XDABR hcall to allow the guest to set both DABR
and DABRX with one call. This adds a real-mode implementation of
H_SET_XDABR, which shares most of its code with the existing H_SET_DABR
implementation. To support this, we add a per-vcpu field to store the
DABRX value plus code to get and set it via the ONE_REG interface.
For Linux guests to use this new hcall, userspace needs to add
"hcall-xdabr" to the set of strings in the /chosen/hypertas-functions
property in the device tree. If userspace does this and then migrates
the guest to a host where the kernel doesn't include this patch, then
userspace will need to implement H_SET_XDABR by writing the specified
DABR value to the DABR using the ONE_REG interface. In that case, the
old kernel will set DABRX to DABRX_USER | DABRX_KERNEL. That should
still work correctly, at least for Linux guests, since Linux guests
cope with getting data breakpoint interrupts in modes that weren't
requested by just ignoring the interrupt, and Linux guests never set
DABRX_BTI.
The other thing this does is to make H_SET_DABR and H_SET_XDABR work
on POWER8, which has the DAWR and DAWRX instead of DABR/X. Guests that
know about POWER8 should use H_SET_MODE rather than H_SET_[X]DABR, but
guests running in POWER7 compatibility mode will still use H_SET_[X]DABR.
For them, this adds the logic to convert DABR/X values into DAWR/X values
on POWER8.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
POWER8 has support for hypervisor doorbell interrupts. Though the
kernel doesn't use them for IPIs on the powernv platform yet, it
probably will in future, so this makes KVM cope gracefully if a
hypervisor doorbell interrupt arrives while in a guest.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
POWER8 has a bit in the LPCR to enable or disable the PURR and SPURR
registers to count when in the guest. Set this bit.
POWER8 has a field in the LPCR called AIL (Alternate Interrupt Location)
which is used to enable relocation-on interrupts. Allow userspace to
set this field.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
* SRR1 wake reason field for system reset interrupt on wakeup from nap
is now a 4-bit field on P8, compared to 3 bits on P7.
* Set PECEDP in LPCR when napping because of H_CEDE so guest doorbells
will wake us up.
* Waking up from nap because of a guest doorbell interrupt is not a
reason to exit the guest.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This allows us to select architecture 2.05 (POWER6) or 2.06 (POWER7)
compatibility modes on a POWER8 processor. (Note that transactional
memory is disabled for usermode if either or both of the PCR_TM_DIS
and PCR_ARCH_206 bits are set.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present this should never happen, since the host kernel sets
HFSCR to allow access to all facilities. It's better to be prepared
to handle it cleanly if it does ever happen, though.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds fields to the struct kvm_vcpu_arch to store the new
guest-accessible SPRs on POWER8, adds code to the get/set_one_reg
functions to allow userspace to access this state, and adds code to
the guest entry and exit to context-switch these SPRs between host
and guest.
Note that DPDES (Directed Privileged Doorbell Exception State) is
shared between threads on a core; hence we store it in struct
kvmppc_vcore and have the master thread save and restore it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
On a threaded processor such as POWER7, we group VCPUs into virtual
cores and arrange that the VCPUs in a virtual core run on the same
physical core. Currently we don't enforce any correspondence between
virtual thread numbers within a virtual core and physical thread
numbers. Physical threads are allocated starting at 0 on a first-come
first-served basis to runnable virtual threads (VCPUs).
POWER8 implements a new "msgsndp" instruction which guest kernels can
use to interrupt other threads in the same core or sub-core. Since
the instruction takes the destination physical thread ID as a parameter,
it becomes necessary to align the physical thread IDs with the virtual
thread IDs, that is, to make sure virtual thread N within a virtual
core always runs on physical thread N.
This means that it's possible that thread 0, which is where we call
__kvmppc_vcore_entry, may end up running some other vcpu than the
one whose task called kvmppc_run_core(), or it may end up running
no vcpu at all, if for example thread 0 of the virtual core is
currently executing in userspace. However, we do need thread 0
to be responsible for switching the MMU -- a previous version of
this patch that had other threads switching the MMU was found to
be responsible for occasional memory corruption and machine check
interrupts in the guest on POWER7 machines.
To accommodate this, we no longer pass the vcpu pointer to
__kvmppc_vcore_entry, but instead let the assembly code load it from
the PACA. Since the assembly code will need to know the kvm pointer
and the thread ID for threads which don't have a vcpu, we move the
thread ID into the PACA and we add a kvm pointer to the virtual core
structure.
In the case where thread 0 has no vcpu to run, it still calls into
kvmppc_hv_entry in order to do the MMU switch, and then naps until
either its vcpu is ready to run in the guest, or some other thread
needs to exit the guest. In the latter case, thread 0 jumps to the
code that switches the MMU back to the host. This control flow means
that now we switch the MMU before loading any guest vcpu state.
Similarly, on guest exit we now save all the guest vcpu state before
switching the MMU back to the host. This has required substantial
code movement, making the diff rather large.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Simplify the handling of lazy EE by going directly from fully-enabled
to hard-disabled. This replaces the lazy_irq_pending() check
(including its misplaced kvm_guest_exit() call).
As suggested by Tiejun Chen, move the interrupt disabling into
kvmppc_prepare_to_enter() rather than have each caller do it. Also
move the IRQ enabling on heavyweight exit into
kvmppc_prepare_to_enter().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
MMIO emulation reads the last instruction executed by the guest
and then emulates. If the guest is running in Little Endian order,
or more generally in a different endian order of the host, the
instruction needs to be byte-swapped before being emulated.
This patch adds a helper routine which tests the endian order of
the host and the guest in order to decide whether a byteswap is
needed or not. It is then used to byteswap the last instruction
of the guest in the endian order of the host before MMIO emulation
is performed.
Finally, kvmppc_handle_load() of kvmppc_handle_store() are modified
to reverse the endianness of the MMIO if required.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
[agraf: add booke handling]
Signed-off-by: Alexander Graf <agraf@suse.de>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Signed-off-by: Mark Salter <msalter@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Add Intel RAPL energy counter support (Stephane Eranian)
- Clean up uprobes (Oleg Nesterov)
- Optimize ring-buffer writes (Peter Zijlstra)
Tooling side changes, user visible:
- 'perf diff':
- Add column colouring improvements (Ramkumar Ramachandra)
- 'perf kvm':
- Add guest related improvements, including allowing to specify a
directory with guest specific /proc information (Dongsheng Yang)
- Add shell completion support (Ramkumar Ramachandra)
- Add '-v' option (Dongsheng Yang)
- Support --guestmount (Dongsheng Yang)
- 'perf probe':
- Support showing source code, asking for variables to be collected
at probe time and other 'perf probe' operations that use DWARF
information.
This supports only binaries with debugging information at this
time, detached debuginfo (aka debuginfo packages) support should
come in later patches (Masami Hiramatsu)
- 'perf record':
- Rename --no-delay option to --no-buffering, better reflecting its
purpose and freeing up '--delay' to take the place of
'--initial-delay', so that 'record' and 'stat' are consistent
(Arnaldo Carvalho de Melo)
- Default the -t/--thread option to no inheritance (Adrian Hunter)
- Make per-cpu mmaps the default (Adrian Hunter)
- 'perf report':
- Improve callchain processing performance (Frederic Weisbecker)
- Retain bfd reference to lookup source line numbers, greatly
optimizing, among other use cases, 'perf report -s srcline'
(Adrian Hunter)
- Improve callchain processing performance even more (Namhyung Kim)
- Add a perf.data file header window in the 'perf report' TUI,
associated with the 'i' hotkey, providing a counterpart to the
--header option in the stdio UI (Namhyung Kim)
- 'perf script':
- Add an option in 'perf script' to print the source line number
(Adrian Hunter)
- Add --header/--header-only options to 'script' and 'report', the
default is not tho show the header info, but as this has been the
default for some time, leave a single line explaining how to
obtain that information (Jiri Olsa)
- Add options to show comm, fork, exit and mmap PERF_RECORD_ events
(Namhyung Kim)
- Print callchains and symbols if they exist (David Ahern)
- 'perf timechart'
- Add backtrace support to CPU info
- Print pid along the name
- Add support for CPU topology
- Add new option --highlight'ing threads, be it by name or, if a
numeric value is provided, that run more than given duration
(Stanislav Fomichev)
- 'perf top':
- Make 'perf top -g' refer to callchains, for consistency with
other tools (David Ahern)
- 'perf trace':
- Handle old kernels where the "raw_syscalls" tracepoints were
called plain "syscalls" (David Ahern)
- Remove thread summary coloring, by Pekka Enberg.
- Honour -m option in 'trace', the tool was offering the option to
set the mmap size, but wasn't using it when doing the actual mmap
on the events file descriptors (Jiri Olsa)
- generic:
- Backport libtraceevent plugin support (trace-cmd repository, with
plugins for jbd2, hrtimer, kmem, kvm, mac80211, sched_switch,
function, xen, scsi, cfg80211 (Jiri Olsa)
- Print session information only if --stdio is given (Namhyung Kim)
Tooling side changes, developer visible (plumbing):
- Improve 'perf probe' exit path, release resources (Masami
Hiramatsu)
- Improve libtraceevent plugins exit path, allowing the registering
of an unregister handler to be called at exit time (Namhyung Kim)
- Add an alias to the build test makefile (make -C tools/perf
build-test) (Namhyung Kim)
- Get rid of die() and friends (good riddance!) in libtraceevent
(Namhyung Kim)
- Fix cross build problems related to pkgconfig and CROSS_COMPILE not
being propagated to the feature tests, leading to features being
tested in the host and then being enabled on the target (Mark
Rutland)
- Improve forked workload error reporting by sending the errno in the
signal data queueing integer field, using sigqueue and by doing the
signal setup in the evlist methods, removing open coded equivalents
in various tools (Arnaldo Carvalho de Melo)
- Do more auto exit cleanup chores in the 'evlist' destructor, so
that the tools don't have to all do that sequence (Arnaldo Carvalho
de Melo)
- Pack 'struct perf_session_env' and 'struct trace' (Arnaldo Carvalho
de Melo)
- Add test for building detached source tarballs (Arnaldo Carvalho de
Melo)
- Move some header files (tools/perf/ to tools/include/ to make them
available to other tools/ dwelling codebases (Namhyung Kim)
- Move logic to warn about kptr_restrict'ed kernels to separate
function in 'report' (Arnaldo Carvalho de Melo)
- Move hist browser selection code to separate function (Arnaldo
Carvalho de Melo)
- Move histogram entries collapsing to separate function (Arnaldo
Carvalho de Melo)
- Introduce evlist__for_each() & friends (Arnaldo Carvalho de Melo)
- Automate setup of FEATURE_CHECK_(C|LD)FLAGS-all variables (Jiri
Olsa)
- Move arch setup into seprate Makefile (Jiri Olsa)
- Make libtraceevent install target quieter (Jiri Olsa)
- Make tests/make output more compact (Jiri Olsa)
- Ignore generated files in feature-checks (Chunwei Chen)
- Introduce pevent_filter_strerror() in libtraceevent, similar in
purpose to libc's strerror() function (Namhyung Kim)
- Use perf_data_file methods to write output file in 'record' and
'inject' (Jiri Olsa)
- Use pr_*() functions where applicable in 'report' (Namhyumg Kim)
- Add 'machine' 'addr_location' struct to have full picture (machine,
thread, map, symbol, addr) for a (partially) resolved address,
reducing function signatures (Arnaldo Carvalho de Melo)
- Reduce code duplication in the histogram entry creation/insertion
(Arnaldo Carvalho de Melo)
- Auto allocate annotation histogram data structures (Arnaldo
Carvalho de Melo)
- No need to test against NULL before calling free, also set freed
memory in struct pointers to NULL, to help fixing use after free
bugs (Arnaldo Carvalho de Melo)
- Rename some struct DSO binary_type related members and methods, to
clarify its purpose and need for differentiation (symtab_type, ie
one is about the files .text, CFI, etc, i.e. its binary contents,
and the other is about where the symbol table came from (Arnaldo
Carvalho de Melo)
- Convert to new topic libraries, starting with an API one (sysfs,
debugfs, etc), renaming liblk in the process (Borislav Petkov)
- Get rid of some more panic() like error handling in libtraceevent.
(Namhyung Kim)
- Get rid of panic() like calls in libtraceevent (Namyung Kim)
- Start carving out symbol parsing routines (perf, just moving
routines to topic files in tools/lib/symbol/, tools that want to
use it need to integrate it directly, ie no
tools/lib/symbol/Makefile is provided (Arnaldo Carvalho de Melo)
- Assorted refactoring patches, moving code around and adding utility
evlist methods that will be used in the IPT patchset (Adrian
Hunter)
- Assorted mmap_pages handling fixes (Adrian Hunter)
- Several man pages typo fixes (Dongsheng Yang)
- Get rid of several die() calls in libtraceevent (Namhyung Kim)
- Use basename() in a more robust way, to avoid problems related to
different system library implementations for that function
(Stephane Eranian)
- Remove open coded management of short_name_allocated member (Adrian
Hunter)
- Several cleanups in the "dso" methods, constifying some parameters
and renaming some fields to clarify its purpose (Arnaldo Carvalho
de Melo)
- Add per-feature check flags, fixing libunwind related build
problems on some architectures (Jean Pihet)
- Do not disable source line lookup just because of one failure.
(Adrian Hunter)
- Several 'perf kvm' man page corrections (Dongsheng Yang)
- Correct the message in feature-libnuma checking, swowing the right
devel package names for various distros (Dongsheng Yang)
- Polish 'readn()' function and introduce its counterpart,
'writen()' (Jiri Olsa)
- Start moving timechart state from global variables to a 'perf_tool'
derived 'timechart' struct (Arnaldo Carvalho de Melo)
... and lots of fixes and improvements I forgot to list"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (282 commits)
perf tools: Remove unnecessary callchain cursor state restore on unmatch
perf callchain: Spare double comparison of callchain first entry
perf tools: Do proper comm override error handling
perf symbols: Export elf_section_by_name and reuse
perf probe: Release all dynamically allocated parameters
perf probe: Release allocated probe_trace_event if failed
perf tools: Add 'build-test' make target
tools lib traceevent: Unregister handler when xen plugin is unloaded
tools lib traceevent: Unregister handler when scsi plugin is unloaded
tools lib traceevent: Unregister handler when jbd2 plugin is is unloaded
tools lib traceevent: Unregister handler when cfg80211 plugin is unloaded
tools lib traceevent: Unregister handler when mac80211 plugin is unloaded
tools lib traceevent: Unregister handler when sched_switch plugin is unloaded
tools lib traceevent: Unregister handler when kvm plugin is unloaded
tools lib traceevent: Unregister handler when kmem plugin is unloaded
tools lib traceevent: Unregister handler when hrtimer plugin is unloaded
tools lib traceevent: Unregister handler when function plugin is unloaded
tools lib traceevent: Add pevent_unregister_print_function()
tools lib traceevent: Add pevent_unregister_event_handler()
tools lib traceevent: fix pointer-integer size mismatch
...
Pull core locking changes from Ingo Molnar:
- futex performance increases: larger hashes, smarter wakeups
- mutex debugging improvements
- lots of SMP ordering documentation updates
- introduce the smp_load_acquire(), smp_store_release() primitives.
(There are WIP patches that make use of them - not yet merged)
- lockdep micro-optimizations
- lockdep improvement: better cover IRQ contexts
- liblockdep at last. We'll continue to monitor how useful this is
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
futexes: Fix futex_hashsize initialization
arch: Re-sort some Kbuild files to hopefully help avoid some conflicts
futexes: Avoid taking the hb->lock if there's nothing to wake up
futexes: Document multiprocessor ordering guarantees
futexes: Increase hash table size for better performance
futexes: Clean up various details
arch: Introduce smp_load_acquire(), smp_store_release()
arch: Clean up asm/barrier.h implementations using asm-generic/barrier.h
arch: Move smp_mb__{before,after}_atomic_{inc,dec}.h into asm/atomic.h
locking/doc: Rename LOCK/UNLOCK to ACQUIRE/RELEASE
mutexes: Give more informative mutex warning in the !lock->owner case
powerpc: Full barrier for smp_mb__after_unlock_lock()
rcu: Apply smp_mb__after_unlock_lock() to preserve grace periods
Documentation/memory-barriers.txt: Downgrade UNLOCK+BLOCK
locking: Add an smp_mb__after_unlock_lock() for UNLOCK+BLOCK barrier
Documentation/memory-barriers.txt: Document ACCESS_ONCE()
Documentation/memory-barriers.txt: Prohibit speculative writes
Documentation/memory-barriers.txt: Add long atomic examples to memory-barriers.txt
Documentation/memory-barriers.txt: Add needed ACCESS_ONCE() calls to memory-barriers.txt
Revert "smp/cpumask: Make CONFIG_CPUMASK_OFFSTACK=y usable without debug dependency"
...
Pull core debug changes from Ingo Molnar:
"Currently there are two methods to set the panic_timeout: via
'panic=X' boot commandline option, or via /proc/sys/kernel/panic.
This tree adds a third panic_timeout configuration method:
configuration via Kconfig, via CONFIG_PANIC_TIMEOUT=X - useful to
distros that generally want their kernel defaults to come with the
.config.
CONFIG_PANIC_TIMEOUT defaults to 0, which was the previous default
value of panic_timeout.
Doing that unearthed a few arch trickeries regarding arch-special
panic_timeout values and related complications - hopefully all
resolved to the satisfaction of everyone"
* 'core-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
powerpc: Clean up panic_timeout usage
MIPS: Remove panic_timeout settings
panic: Make panic_timeout configurable
For user space packet capturing libraries such as libpcap, there's
currently only one way to check which BPF extensions are supported
by the kernel, that is, commit aa1113d9f8 ("net: filter: return
-EINVAL if BPF_S_ANC* operation is not supported"). For querying all
extensions at once this might be rather inconvenient.
Therefore, this patch introduces a new option which can be used as
an argument for getsockopt(), and allows one to obtain information
about which BPF extensions are supported by the current kernel.
As David Miller suggests, we do not need to define any bits right
now and status quo can just return 0 in order to state that this
versions supports SKF_AD_PROTOCOL up to SKF_AD_PAY_OFFSET. Later
additions to BPF extensions need to add their bits to the
bpf_tell_extensions() function, as documented in the comment.
Signed-off-by: Michal Sekletar <msekleta@redhat.com>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its possible that OPAL may be writing to host memory during
kexec (like dump retrieve scenario). In this situation we might
end up corrupting host memory.
This patch makes OPAL sync call to make sure OPAL stops
writing to host memory before kexec'ing.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For one PCI error relevant OPAL event, we possibly have multiple
EEH errors for that. For example, multiple frozen PEs detected on
different PHBs. Unfortunately, we didn't cover the case. The patch
enumarates the return value from eeh_ops::next_error() and change
eeh_handle_special_event() and eeh_ops::next_error() to handle all
existing EEH errors.
As Ben pointed out, we needn't list_for_each_entry_safe() since we
are not deleting any PHB from the hose_list and the EEH serialized
lock should be held while purging EEH events. The patch covers those
suggestions as well.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fix the below crash
NIP [c00000000004cee4] .__hash_page_thp+0x2a4/0x440
LR [c0000000000439ac] .hash_page+0x18c/0x5e0
...
Call Trace:
[c000000736103c40] [00001ffffb000000] 0x1ffffb000000(unreliable)
[437908.479693] [c000000736103d50] [c0000000000439ac] .hash_page+0x18c/0x5e0
[437908.479699] [c000000736103e30] [c00000000000924c] .do_hash_page+0x4c/0x58
On ppc64 we use the pgtable for storing the hpte slot information and
store address to the pgtable at a constant offset (PTRS_PER_PMD) from
pmd. On mremap, when we switch the pmd, we need to withdraw and deposit
the pgtable again, so that we find the pgtable at PTRS_PER_PMD offset
from new pmd.
We also want to move the withdraw and deposit before the set_pmd so
that, when page fault find the pmd as trans huge we can be sure that
pgtable can be located at the offset.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, when we have a process using the transactional memory
facilities on POWER8 (that is, the processor is in transactional
or suspended state), and the process enters the kernel and the
kernel then uses the floating-point or vector (VMX/Altivec) facility,
we end up corrupting the user-visible FP/VMX/VSX state. This
happens, for example, if a page fault causes a copy-on-write
operation, because the copy_page function will use VMX to do the
copy on POWER8. The test program below demonstrates the bug.
The bug happens because when FP/VMX state for a transactional process
is stored in the thread_struct, we store the checkpointed state in
.fp_state/.vr_state and the transactional (current) state in
.transact_fp/.transact_vr. However, when the kernel wants to use
FP/VMX, it calls enable_kernel_fp() or enable_kernel_altivec(),
which saves the current state in .fp_state/.vr_state. Furthermore,
when we return to the user process we return with FP/VMX/VSX
disabled. The next time the process uses FP/VMX/VSX, we don't know
which set of state (the current register values, .fp_state/.vr_state,
or .transact_fp/.transact_vr) we should be using, since we have no
way to tell if we are still in the same transaction, and if not,
whether the previous transaction succeeded or failed.
Thus it is necessary to strictly adhere to the rule that if FP has
been enabled at any point in a transaction, we must keep FP enabled
for the user process with the current transactional state in the
FP registers, until we detect that it is no longer in a transaction.
Similarly for VMX; once enabled it must stay enabled until the
process is no longer transactional.
In order to keep this rule, we add a new thread_info flag which we
test when returning from the kernel to userspace, called TIF_RESTORE_TM.
This flag indicates that there is FP/VMX/VSX state to be restored
before entering userspace, and when it is set the .tm_orig_msr field
in the thread_struct indicates what state needs to be restored.
The restoration is done by restore_tm_state(). The TIF_RESTORE_TM
bit is set by new giveup_fpu/altivec_maybe_transactional helpers,
which are called from enable_kernel_fp/altivec, giveup_vsx, and
flush_fp/altivec_to_thread instead of giveup_fpu/altivec.
The other thing to be done is to get the transactional FP/VMX/VSX
state from .fp_state/.vr_state when doing reclaim, if that state
has been saved there by giveup_fpu/altivec_maybe_transactional.
Having done this, we set the FP/VMX bit in the thread's MSR after
reclaim to indicate that that part of the state is now valid
(having been reclaimed from the processor's checkpointed state).
Finally, in the signal handling code, we move the clearing of the
transactional state bits in the thread's MSR a bit earlier, before
calling flush_fp_to_thread(), so that we don't unnecessarily set
the TIF_RESTORE_TM bit.
This is the test program:
/* Michael Neuling 4/12/2013
*
* See if the altivec state is leaked out of an aborted transaction due to
* kernel vmx copy loops.
*
* gcc -m64 htm_vmxcopy.c -o htm_vmxcopy
*
*/
/* We don't use all of these, but for reference: */
int main(int argc, char *argv[])
{
long double vecin = 1.3;
long double vecout;
unsigned long pgsize = getpagesize();
int i;
int fd;
int size = pgsize*16;
char tmpfile[] = "/tmp/page_faultXXXXXX";
char buf[pgsize];
char *a;
uint64_t aborted = 0;
fd = mkstemp(tmpfile);
assert(fd >= 0);
memset(buf, 0, pgsize);
for (i = 0; i < size; i += pgsize)
assert(write(fd, buf, pgsize) == pgsize);
unlink(tmpfile);
a = mmap(NULL, size, PROT_READ|PROT_WRITE, MAP_PRIVATE, fd, 0);
assert(a != MAP_FAILED);
asm __volatile__(
"lxvd2x 40,0,%[vecinptr] ; " // set 40 to initial value
TBEGIN
"beq 3f ;"
TSUSPEND
"xxlxor 40,40,40 ; " // set 40 to 0
"std 5, 0(%[map]) ;" // cause kernel vmx copy page
TABORT
TRESUME
TEND
"li %[res], 0 ;"
"b 5f ;"
"3: ;" // Abort handler
"li %[res], 1 ;"
"5: ;"
"stxvd2x 40,0,%[vecoutptr] ; "
: [res]"=r"(aborted)
: [vecinptr]"r"(&vecin),
[vecoutptr]"r"(&vecout),
[map]"r"(a)
: "memory", "r0", "r3", "r4", "r5", "r6", "r7");
if (aborted && (vecin != vecout)){
printf("FAILED: vector state leaked on abort %f != %f\n",
(double)vecin, (double)vecout);
exit(1);
}
munmap(a, size);
close(fd);
printf("PASSED!\n");
return 0;
}
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
TIF_PERFMON_WORK and TIF_PERFMON_CTXSW are completely unused. They
appear to be related to the old perfmon2 code, which has been
superseded by the perf_event infrastructure. This removes their
definitions so that the bits can be used for other purposes.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Huge Dickins reported an issue that b5ff4211a8
"powerpc/book3s: Queue up and process delayed MCE events" breaks the
PowerMac G5 boot. This patch fixes it by moving the mce even processing
away from syscall exit, which was wrong to do that in first place, and
using irq work framework to delay processing of mce event.
Reported-by: Hugh Dickins <hughd@google.com
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On POWER platforms, the hypervisor can notify the guest kernel about dynamic
changes in the cpu-numa associativity (VPHN topology update). Hence the
cpu-to-node mappings that we got from the firmware during boot, may no longer
be valid after such updates. This is handled using the arch_update_cpu_topology()
hook in the scheduler, and the sched-domains are rebuilt according to the new
mappings.
But unfortunately, at the moment, CPU hotplug ignores these updated mappings
and instead queries the firmware for the cpu-to-numa relationships and uses
them during CPU online. So the kernel can end up assigning wrong NUMA nodes
to CPUs during subsequent CPU hotplug online operations (after booting).
Further, a particularly problematic scenario can result from this bug:
On POWER platforms, the SMT mode can be switched between 1, 2, 4 (and even 8)
threads per core. The switch to Single-Threaded (ST) mode is performed by
offlining all except the first CPU thread in each core. Switching back to
SMT mode involves onlining those other threads back, in each core.
Now consider this scenario:
1. During boot, the kernel gets the cpu-to-node mappings from the firmware
and assigns the CPUs to NUMA nodes appropriately, during CPU online.
2. Later on, the hypervisor updates the cpu-to-node mappings dynamically and
communicates this update to the kernel. The kernel in turn updates its
cpu-to-node associations and rebuilds its sched domains. Everything is
fine so far.
3. Now, the user switches the machine from SMT to ST mode (say, by running
ppc64_cpu --smt=1). This involves offlining all except 1 thread in each
core.
4. The user then tries to switch back from ST to SMT mode (say, by running
ppc64_cpu --smt=4), and this involves onlining those threads back. Since
CPU hotplug ignores the new mappings, it queries the firmware and tries to
associate the newly onlined sibling threads to the old NUMA nodes. This
results in sibling threads within the same core getting associated with
different NUMA nodes, which is incorrect.
The scheduler's build-sched-domains code gets thoroughly confused with this
and enters an infinite loop and causes soft-lockups, as explained in detail
in commit 3be7db6ab (powerpc: VPHN topology change updates all siblings).
So to fix this, use the numa_cpu_lookup_table to remember the updated
cpu-to-node mappings, and use them during CPU hotplug online operations.
Further, we also need to ensure that all threads in a core are assigned to a
common NUMA node, irrespective of whether all those threads were online during
the topology update. To achieve this, we take care not to use cpu_sibling_mask()
since it is not hotplug invariant. Instead, we use cpu_first_sibling_thread()
and set up the mappings manually using the 'threads_per_core' value for that
particular platform. This helps us ensure that we don't hit this bug with any
combination of CPU hotplug and SMT mode switching.
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error comes to one specific PCI device before its driver
is loaded, we will apply hotplug to recover the error. During the
plug time, the PCI device will be probed and its driver is loaded.
Then we wrongly calls to the error handlers if the driver supports
EEH explicitly.
The patch intends to fix by introducing flag EEH_DEV_NO_HANDLER and
set it before we remove the PCI device. In turn, we can avoid wrongly
calls the error handlers of the PCI device after its driver loaded.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
