Maxburst was not set when doing the dma slave configuration. This value
is checked by the recently introduced xdmac. It causes an error when
doing the slave configuration and so prevents from using dma.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12 and later
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tasklet may be scheduled and executed after serial port
was shutdown, for example, DMA rx callback will schedule the
tasklet while serial port is shutting down, especially serial
port is sending and receiving data in a higher baud rate and
it's killed by external program. In this case, tasklet_kill
can only clear the current scheduling out, so tasklet should
be disabled to prevent being executed in later scheduling.
Otherwise, the tasklet executed after serial port was shutdown
can lead to kernel crash.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The property in device tree will be reading each time when tty is opened,
so the ops of serial port should be set after that instead of setting once
in probe. Otherwise, the ops of serial port is inconsistent with the state
of serial work manner. For example, the atmel serial driver can't work when
switching to PIO mode due to DMA channel is not available.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function of atmel_init_property is to set the work manner of
atmel serial ports according to the property in device trees.
If DMA or PDC is not set or something goes wrong in getting property,
the work manner will switch to general PIO mode, thus there will
not be any failure case in this function. It's actually a procedure.
So changing the return type from int to void.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer size set in DMA is inconsistent with its allocation.
So keep them consistent here. The structure atmel_uart_char is
used in PIO mode with its meaning. But here in DMA, all of the
buffer is treated as general char.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only use buf of ring In DMA rx function while using buf of xmit
in DMA tx function. So in DMA rx we need definitively to check the
buf of ring which is corresponding to DMA rx function. And use macro
PAGE_ALIGNED to simplify the expression.
Signed-off-by: Leilei Zhao <leilei.zhao@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mctrl_gpio_init at present doesn't return NULL. (It might be used in the
future when no gpios are to be used indicating success.) Properly pass
error returned and also make driver probing fail on error.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ line connected to the DBGU UART is often shared with a timer device
which request the IRQ with IRQF_NO_SUSPEND.
Since the UART driver is correctly disabling IRQs when entering suspend
we can safely request the IRQ with IRQF_COND_SUSPEND so that irq core
will not complain about mixing IRQF_NO_SUSPEND and !IRQF_NO_SUSPEND.
Rework the interrupt handler to wake the system up when an interrupt
happens on the DEBUG_UART while the system is suspended.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes many bugs in the code dealing with the hardware handshake.
As an example, in atmel_set_termios(), we used to test whether the CRTSCTS
c_cflag was set. If so, we selected the "Hardware Handshake" mode through the
Mode Register. However, few lines below the mode was reset to "Normal" (0).
So there was no way to select the "Hardware Handshake" mode. To fix this issue,
we moved the CRTSCRTS c_cflag test AFTER the mode has been reset to "Normal".
Also setting the RTSEN and RTSDIS bits in the Control Register has different
results whether the USART is set in "Normal" or "Hardware Handshake" mode:
1) "Normal" mode
- the RTSEN bit forces the RTS line to low level, which tells the remote peer
that we are ready to received new data.
- the RTSDIS bit forces the RTS line to high level, which tells the remote peer
to stop sending new data.
2) "Hardware Handshake" mode
- the RTSEN bit forces the RTS line to high level.
- the RTSDIS bit lets the hardware control the RTS line.
WARNING:
when FIFOs are not available or not enabled, the RTS line is controlled by the
PDC. This is why using the Hardware Handshake mode requires using the PDC
channel for reception. However the Hardware Handshake mode DOES NOT work with
DMA controller since it cannot control the RTS line.
Future designs with FIFOs will introduce a new feature: the RTS line will be
controlled by the RX FIFO using thresholds. This patch was tested with this new
design.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-EDEFER error wasn't handle properly by atmel_serial_probe().
As an example, when atmel_serial_probe() is called for the first time, we pass
the test_and_set_bit() test to check whether the port has already been
initalized. Then we call atmel_init_port(), which may return -EDEFER, possibly
returned before by clk_get(). Consequently atmel_serial_probe() used to return
this error code WITHOUT clearing the port bit in the "atmel_ports_in_use" mask.
When atmel_serial_probe() was called for the second time, it used to fail on
the test_and_set_bit() function then returning -EBUSY.
When atmel_serial_probe() fails, this patch make it clear the port bit in the
"atmel_ports_in_use" mask, if needed, before returning the error code.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel_serial_probe() calls atmel_init_port(). In turn, atmel_init_port() calls
clk_disable_unprepare() to disable the peripheral clock before returning.
Later atmel_serial_probe() accesses some I/O registers such as the Mode and
Control registers for RS485 support then the Name and Version registers, through a call to
atmel_get_ip_name(), but at that moment the peripheral clock was still
disabled.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Introduce an homogeneous lock system between setting and using the rs485
data of the uart_port.
This patch should not be split into multiple ones in order to avoid
leaving the tree in an unstable state.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Suggested-by: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to unify all the rs485 ioctl handling.
Use the implementation of TIOC[GS]RS485 ioctl handling on serial_core.
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switching to the N_PPS line discipline may require enabling
modem status interrupts; conversely switching from N_PPS may
require disabling modem status interrupts.
Affected drivers:
8250
amba-pl010
atmel
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three UART drivers (8250, atmel & amba-pl010) directly call their
enable_ms() method; the uart port lock must be acquired before
any h/w programming.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART drivers which enable modem status interrupts when switching
to N_PPS line discipline need to determine if modem status
interrupts should be disabled when switching from N_PPS.
Specifically, the set_ldisc() notification needs to evaluate
UART_ENABLE_MS() which requires termios->c_cflag.
Convert in-tree UART drivers to new interface.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are removing the dmaengine_device_control API, that shouldn't even have been
exposed in the first place. Change the callers to use the proper API.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch swaps the use "tail" and "head" to fit the semantic of the linux
circular buffer documentation:
- head: the point at which the producer (the DMA controller) inserts items.
- tail: the point at which the consumer (the serial framework) finds the next
item.
Besides the former code of the rx ring buffer didn't manage the case where
head < tail, which might lead to loss of data. To fix this bug the data are now
sent from the DMA buffer to the serial framework in two steps:
1 - First, we test if head < tail. If so, we copy the data from tail to the end
of the DMA buffer then reset tail to zero.
2 - Finally, we copy data from tail to head then set tail to head.
In addition, since tty_insert_flip_string() may now be called twice,
atmel_flip_buffer_rx_dma() becomes less efficient than moving the calls
dma_sync_sg_for_cpu(), dma_sync_sg_for_device(), tty_insert_flip_string() and
tty_flip_buffer_push() directly into atmel_rx_from_dma().
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the context of the final tty & port close, flushing the tx
ring buffer after the hardware has already been shutdown and
the ring buffer freed is neither required nor desirable.
uart_flush_buffer() performs 3 operations:
1. Resets tx ring buffer indices, but the tx ring buffer has
already been freed and the indices are reset if the port is
re-opened.
2. Calls uart driver's flush_buffer() method
5 in-tree uart drivers define flush_buffer() methods:
amba-pl011, atmel-serial, imx, serial-tegra, timbuart
These have been refactored into the shutdown() method, if
required.
3. Kicks the ldisc for more writing, but this is undesirable.
The file handle is being released; any waiting writer will
will be kicked out by tty_release() with a warning. Further,
the N_TTY ldisc may generate SIGIO for a file handle which
is no longer valid.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
The atmel serial driver uses dmaengine APIs but never included the dmaengine
header as it was getting inculded thru one of driver headers.
commit 3d588f83e4 - "dmaengine: dw: split
dma-dw.h to platform and private parts" broke this as it moved headers
around. Fix this by doing the right thing to include the dmaengine header
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 08f738be88 (serial: at91: add tx dma support)
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In set_termios(), interrupts where not disabled if UART_ENABLE_MS() was
false.
Tested on at91sam9g35.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org> # >= 3.16
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On sam9x5, dedicated CTS (and RTS) pins are unusable together with the
LCDC, the EMAC, or the MMC because they share the same line.
Moreover, the USART controller doesn't handle DTR/DSR/DCD/RI signals,
so we have to control them via GPIO.
This patch permits to use GPIOs to control the CTS/RTS/DTR/DSR/DCD/RI
signals.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These cleanup patches are mainly move stuff around and should all
be harmless. They are mainly split out so that other branches can
be based on top to avoid conflicts.
Notable changes are:
* We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used. (Uwe Kleine-König)
* The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions. (Kumar Gala)
* A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
* Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
* mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
* at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GcBb
-----END PGP SIGNATURE-----
Merge tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
commit 95e629b761 removed the use of board
specific hooks in serial_at91.h, so now, the open/close hook are just
dead code.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
This fixes a driver bug which stopped the whole system (in case
of serial console).
This log message is not useful anyway as this information is
printed elsewhere.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart timer will schedule a tasklet when it fires. It is possible that it
can fire inside _shutdown before it is killed in the dma and pdc cleanup
routines. This causes a tasklet that exists after the port is shutdown, so when
the kernel finally executes it, it panics as the tty port is NULL.
This is a somewhat rare condition but its possible if a program keeps on
opening/closing the port. It has been observed in particular with systemd
boot messages that were causing a kernel panic because of this behavior.
Moving the timer deletion to the beginning of the function stops a tasklet from
being scheduled unexpectedly.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Cc: stable <stable@vger.kernel.org> # v3.12
[nicolas.ferre@atmel.com: modify commit message, call setup_timer() in any case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.
To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in. If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:
[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This passes the errata fix using a GPIO to control the RTS pin
on one of the AT91 chips to use gpiolib instead of the
AT91-specific interfaces. Also remove the reliance on
compile-time #defines and the cpu_* check and rely on the
platform passing down the proper GPIO pin through platform
data.
This is a prerequisite for getting rid of the local GPIO
implementation in the AT91 platform and move toward
multiplatform.
The patch also adds device tree support for getting the
RTS GPIO pin from the device tree on DT boot paths.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
On older SoC, the "name" field is not filled in the register map.
Fix the way to figure out if the serial port is an uart or an usart for these
older products (with corresponding properties).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 055560b04a (serial: at91:
distinguish usart and uart) the older products which do not have a
name field in their register map are unable to use their serial output.
As the main console output is usually the serial interface (aka DBGU) it
is pretty unfortunate.
So, instead of failing during probe() we just silently configure the serial
peripheral as an uart. It allows us to use these serial outputs.
The proper solution is proposed in another patch.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the UART lack of receive timeout register, so we use a timer to trigger
data receive.
The DBGU is regarded as UART.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Distinguish usart and uart by read ip name register,
The usart read name is "USAR",
The uart and dbgu read name is "DBGU".
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will switch to pio mode when request of dma or pdc fail.
But soon or later, when the request is success, the transfer mode can switch to them at
next open serial port action.
So in startup stage, we should get original transfer mode.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request a cyclic dma channel for rx dma use. Use cyclic transfer is to prevent
receive data overrun.
We allocate a cycle dma cookie after request channel,
after that, enable uart timeout interrupt in startup stage, when data successful
received, the timeout callback will check the residual bytes and insert
receiving datas into the framework during the transfer interval.
When current descriptor finished, the dma callback will also check the residual
bytes and filp the receiving data.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request a slave dma channel for tx dma use. Tx dma will setup a single transfer,
when transfer complete, it will call atmel_complete_tx_dma to do finish stuff.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use function pointer can avoid define atmel_use_pdc_tx/rx everywhere.
(*prepare_rx/tx)() is in setup transfer stage.
(*schedule_rx/tx)() is in tasklet schedule stage.
(*release_rx/tx)() is used when shutdown the transfer.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
