This solves this bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73361
The problem is that when you quit tvtime it calls STREAMOFF, but then it queues a
bunch of buffers for no good reason before closing the file descriptor.
In the past closing the fd would free the vb queue since that was part of the file
handle struct. Since that was moved to the global struct that no longer happened.
This wouldn't be a problem, but the extra QBUF calls that tvtime does meant that
the buffer list in videobuf (q->stream) contained buffers, so REQBUFS would fail
with -EBUSY.
The solution is to init the list head explicitly when releasing the file
descriptor and to not free the video resource when calling streamoff.
The real fix will hopefully go into kernel 3.16 when the vb2 conversion is
merged. Basically the saa7134 driver with the old videobuf is so full of holes it
ain't funny anymore, so consider this a band-aid for kernels 3.14 and 15.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Setting the P state of the core to max at init time is a hold over
from early implementation of intel_pstate where intel_pstate disabled
cpufreq and loaded VERY early in the boot sequence. This was to
ensure that intel_pstate did not affect boot time. This in not needed
now that intel_pstate is a cpufreq driver.
Removing this covers the case where a CPU has gone through a manual
CPU offline/online cycle and the P state is set to MAX on init and the
CPU immediately goes idle. Due to HW coordination the P state request
on the idle CPU will drag all cores to MAX P state until the load is
reevaluated when to core goes non-idle.
Reported-by: Patrick Marlier <patrick.marlier@gmail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While updating cgroup_freezer locking, 68fafb77d827 ("cgroup_freezer:
replace freezer->lock with freezer_mutex") introduced a bug in
update_if_frozen() where it returns with rcu_read_lock() held. Fix it
by adding rcu_read_unlock() before returning.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
After 96d365e0b8 ("cgroup: make css_set_lock a rwsem and rename it
to css_set_rwsem"), css task iterators requires sleepable context as
it may block on css_set_rwsem. I missed that cgroup_freezer was
iterating tasks under IRQ-safe spinlock freezer->lock. This leads to
errors like the following on freezer state reads and transitions.
BUG: sleeping function called from invalid context at /work
/os/work/kernel/locking/rwsem.c:20
in_atomic(): 0, irqs_disabled(): 0, pid: 462, name: bash
5 locks held by bash/462:
#0: (sb_writers#7){.+.+.+}, at: [<ffffffff811f0843>] vfs_write+0x1a3/0x1c0
#1: (&of->mutex){+.+.+.}, at: [<ffffffff8126d78b>] kernfs_fop_write+0xbb/0x170
#2: (s_active#70){.+.+.+}, at: [<ffffffff8126d793>] kernfs_fop_write+0xc3/0x170
#3: (freezer_mutex){+.+...}, at: [<ffffffff81135981>] freezer_write+0x61/0x1e0
#4: (rcu_read_lock){......}, at: [<ffffffff81135973>] freezer_write+0x53/0x1e0
Preemption disabled at:[<ffffffff81104404>] console_unlock+0x1e4/0x460
CPU: 3 PID: 462 Comm: bash Not tainted 3.15.0-rc1-work+ #10
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
ffff88000916a6d0 ffff88000e0a3da0 ffffffff81cf8c96 0000000000000000
ffff88000e0a3dc8 ffffffff810cf4f2 ffffffff82388040 ffff880013aaf740
0000000000000002 ffff88000e0a3de8 ffffffff81d05974 0000000000000246
Call Trace:
[<ffffffff81cf8c96>] dump_stack+0x4e/0x7a
[<ffffffff810cf4f2>] __might_sleep+0x162/0x260
[<ffffffff81d05974>] down_read+0x24/0x60
[<ffffffff81133e87>] css_task_iter_start+0x27/0x70
[<ffffffff8113584d>] freezer_apply_state+0x5d/0x130
[<ffffffff81135a16>] freezer_write+0xf6/0x1e0
[<ffffffff8112eb88>] cgroup_file_write+0xd8/0x230
[<ffffffff8126d7b7>] kernfs_fop_write+0xe7/0x170
[<ffffffff811f0756>] vfs_write+0xb6/0x1c0
[<ffffffff811f121d>] SyS_write+0x4d/0xc0
[<ffffffff81d08292>] system_call_fastpath+0x16/0x1b
freezer->lock used to be used in hot paths but that time is long gone
and there's no reason for the lock to be IRQ-safe spinlock or even
per-cgroup. In fact, given the fact that a cgroup may contain large
number of tasks, it's not a good idea to iterate over them while
holding IRQ-safe spinlock.
Let's simplify locking by replacing per-cgroup freezer->lock with
global freezer_mutex. This also makes the comments explaining the
intricacies of policy inheritance and the locking around it as the
states are protected by a common mutex.
The conversion is mostly straight-forward. The followings are worth
mentioning.
* freezer_css_online() no longer needs double locking.
* freezer_attach() now performs propagation simply while holding
freezer_mutex. update_if_frozen() race no longer exists and the
comment is removed.
* freezer_fork() now tests whether the task is in root cgroup using
the new task_css_is_root() without doing rcu_read_lock/unlock(). If
not, it grabs freezer_mutex and performs the operation.
* freezer_read() and freezer_change_state() grab freezer_mutex across
the whole operation and pin the css while iterating so that each
descendant processing happens in sleepable context.
Fixes: 96d365e0b8 ("cgroup: make css_set_lock a rwsem and rename it to css_set_rwsem")
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Determining the css of a task usually requires RCU read lock as that's
the only thing which keeps the returned css accessible till its
reference is acquired; however, testing whether a task belongs to the
root can be performed without dereferencing the returned css by
comparing the returned pointer against the root one in init_css_set[]
which never changes.
Implement task_css_is_root() which can be invoked in any context.
This will be used by the scheduled cgroup_freezer change.
v2: cgroup no longer supports modular controllers. No need to export
init_css_set. Pointed out by Li.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
We need to find a smarter way to switch to 64-bit FADT addresses according
to the bug report. This patch reverts Linux to the original behavior.
Fixes: 0249ed2444 (ACPICA: Add option to favor 32-bit FADT addresses.)
References: https://bugzilla.kernel.org/show_bug.cgi?id=74021
Reported-and-tested-by: Oswald Buddenhagen <ossi@kde.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The DMI tag used to identify Dell Inspiron 7520 should be product name
instead of product version.
Fixes: 0e9f81d3b7 (ACPI / video: Add systems that should favour native backlight interface)
Reported-and-tested-by: Téo Mazars <teomazars@gmail.com>
References: https://bugzilla.redhat.com/show_bug.cgi?id=909552
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The kernfs open method - kernfs_fop_open() - inherited extra
permission checks from sysfs. While the vfs layer allows ignoring the
read/write permissions checks if the issuer has CAP_DAC_OVERRIDE,
sysfs explicitly denied open regardless of the cap if the file doesn't
have any of the UGO perms of the requested access or doesn't implement
the requested operation. It can be debated whether this was a good
idea or not but the behavior is too subtle and dangerous to change at
this point.
After cgroup got converted to kernfs, this extra perm check also got
applied to cgroup breaking libcgroup which opens write-only files with
O_RDWR as root. This patch gates the extra open permission check with
a new flag KERNFS_ROOT_EXTRA_OPEN_PERM_CHECK and enables it for sysfs.
For sysfs, nothing changes. For cgroup, root now can perform any
operation regardless of the permissions as it was before kernfs
conversion. Note that kernfs still fails unimplemented operations
with -EINVAL.
While at it, add comments explaining KERNFS_ROOT flags.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Wagin <avagin@gmail.com>
Tested-by: Andrey Wagin <avagin@gmail.com>
Cc: Li Zefan <lizefan@huawei.com>
References: http://lkml.kernel.org/g/CANaxB-xUm3rJ-Cbp72q-rQJO5mZe1qK6qXsQM=vh0U8upJ44+A@mail.gmail.com
Fixes: 2bd59d48eb ("cgroup: convert to kernfs")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_device_exclusion_range(u16 devid, struct ivmd_header *m) enables
exclusion range for ONE device. IOMMU does not translate the access
to the exclusion range from the device.
The device is specified by input argument 'devid'. But 'devid' is not
passed to the actual set function set_dev_entry_bit(), instead
'm->devid' is passed. 'm->devid' does not specify the exact device
which needs enable the exclusion range. 'm->devid' represents DeviceID
field of IVMD, which has different meaning depends on IVMD type.
The caller init_exclusion_range() sets 'devid' for ONE device. When
m->type is equal to ACPI_IVMD_TYPE_ALL or ACPI_IVMD_TYPE_RANGE,
'm->devid' is not equal to 'devid'.
This patch fixes 'm->devid' to 'devid'.
Signed-off-by: Su Friendy <friendy.su@sony.com.cn>
Signed-off-by: Tamori Masahiro <Masahiro.Tamori@jp.sony.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
get_user_pages requires caller to hold a read lock on mmap_sem.
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
An apparent cut and paste error prevents the correct flags from being
set on the alias device resulting in MSI on conventional PCI devices
failing to work. This also produces error events from the IOMMU like:
AMD-Vi: Event logged [INVALID_DEVICE_REQUEST device=00:14.4 address=0x000000fdf8000000 flags=0x0a00]
Where 14.4 is a PCIe-to-PCI bridge with a device behind it trying to
use MSI interrupts.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Broadwell display controller has 3 stream DMA engines. DMA0 cannot update DMA
postion buffer properly while DMA1 and DMA2 can work well. So this patch masks
the buggy DMA0 by keeping it as opened.
This is a tentative workaround, so keep the change small as Takashi suggested.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0071 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- fix for regression in handling of F_GETLK commands
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pr3z
-----END PGP SIGNATURE-----
Merge tag 'locks-v3.15-4' of git://git.samba.org/jlayton/linux
Pull file locking fix from Jeff Layton:
"Fix for regression in handling of F_GETLK commands"
* tag 'locks-v3.15-4' of git://git.samba.org/jlayton/linux:
locks: only validate the lock vs. f_mode in F_SETLK codepaths
and add support for additional chip revisions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PVvi
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix resource leak as well as broken store function in emc1403 driver,
and add support for additional chip revisions"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (emc1403) Support full range of known chip revision numbers
hwmon: (emc1403) Fix resource leak on module unload
hwmon: (emc1403) fix inverted store_hyst()
Pull a percpu fix from Tejun Heo:
"Fix for a percpu allocator bug where it could try to kfree() a memory
region allocated using vmalloc(). The bug has been there for years
now and is unlikely to have ever triggered given the size of struct
pcpu_chunk. It's still theoretically possible and the fix is simple
and safe enough, so the patch is marked with -stable"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: make pcpu_alloc_chunk() use pcpu_mem_free() instead of kfree()
Pull workqueue fixes from Tejun Heo:
"Fixes for two bugs in workqueue.
One is exiting with internal mutex held in a failure path of
wq_update_unbound_numa(). The other is a subtle and unlikely
use-after-possible-last-put in the rescuer logic. Both have been
around for quite some time now and are unlikely to have triggered
noticeably often. All patches are marked for -stable backport"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: fix a possible race condition between rescuer and pwq-release
workqueue: make rescuer_thread() empty wq->maydays list before exiting
workqueue: fix bugs in wq_update_unbound_numa() failure path
Pull cgroup fixes from Tejun Heo:
"During recent restructuring, device_cgroup unified config input check
and enforcement logic; unfortunately, it turned out to share too much.
Aristeu's patches fix the breakage and marked for -stable backport.
The other two patches are fallouts from kernfs conversion. The blkcg
change is temporary and will go away once kernfs internal locking gets
simplified (patches pending)"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
blkcg: use trylock on blkcg_pol_mutex in blkcg_reset_stats()
device_cgroup: check if exception removal is allowed
device_cgroup: fix the comment format for recently added functions
device_cgroup: rework device access check and exception checking
cgroup: fix the retry path of cgroup_mount()
Pull cifs fix from Steve French:
"Small cifs fix for metadata caching"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix actimeo=0 corner case when cifs_i->time == jiffies
Both tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=9QhO
-----END PGP SIGNATURE-----
Merge tag 'md/3.15-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"Two bugfixes for md in 3.15
Both tagged for -stable"
* tag 'md/3.15-fixes' of git://neil.brown.name/md:
md: avoid possible spinning md thread at shutdown.
md/raid10: call wait_barrier() for each request submitted.
Seems like we've had more fixes than usual this release cycle, but
there's nothing in particular that we're doing differently. Perhaps it's
just one of those cycles where more people are finding more regressions
(and/or that the latency of when people actually test what's been in
the tree for a while is catching up so that we get the bug reports now).
The bigger changes here are are for TI and Marvell platforms:
* Timing changes for GPMC (generic localbus) on OMAP causing some largeish
DTS deltas.
* Fixes to window allocation on PCI for mvebu touching drivers/ stuff. Patches
have acks from subsystem maintainers where needed.
* A fix from Thomas for a botched DT conversion in drivers/edma.
There's a handful of other fixes for the above platforms as well as sunxi,
at91, i.MX. I also included a MAINTAINER update for Broadcom, and a trivial
move of a binding doc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=76ry
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Seems like we've had more fixes than usual this release cycle, but
there's nothing in particular that we're doing differently. Perhaps
it's just one of those cycles where more people are finding more
regressions (and/or that the latency of when people actually test
what's been in the tree for a while is catching up so that we get the
bug reports now).
The bigger changes here are are for TI and Marvell platforms:
* Timing changes for GPMC (generic localbus) on OMAP causing some
largeish DTS deltas.
* Fixes to window allocation on PCI for mvebu touching drivers/
stuff. Patches have acks from subsystem maintainers where needed.
* A fix from Thomas for a botched DT conversion in drivers/edma.
There's a handful of other fixes for the above platforms as well as
sunxi, at91, i.MX. I also included a MAINTAINER update for Broadcom,
and a trivial move of a binding doc.
I know you said you'd be offline this week, but I might as well post
it for when you return. :)"
I'm not quite offline yet. Doing a few pulls in the last hour before my
internet goes away..
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
MAINTAINERS: update Broadcom ARM tree location and add an SoC family
ARM: dts: i.MX53: Fix ipu register space size
ARM: dts: kirkwood: fix mislocated pcie-controller nodes
ARM: sunxi: Enable GMAC in sunxi_defconfig
ARM: common: edma: Fix xbar mapping
ARM: sun7i: Fix i2c4 base address
ARM: Kirkwood: T5325: Fix double probe of Codec
ARM: mvebu: enable the SATA interface on Armada 375 DB
ARM: mvebu: specify I2C bus frequency on Armada 370 DB
ARM: mvebu: use qsgmii phy-mode for Armada XP GP interfaces
ARM: mvebu: fix NOR bus-width in Armada XP OpenBlocks AX3 Device Tree
ARM: mvebu: fix NOR bus-width in Armada XP DB Device Tree
ARM: mvebu: fix NOR bus-width in Armada XP GP Device Tree
ARM: dts: AM3517: Disable absent IPs inherited from OMAP3
ARM: dts: OMAP2: Fix interrupts for OMAP2420 mailbox
ARM: dts: OMAP5: Add mailbox dt node to fix boot warning
ARM: OMAP5: Switch to THUMB mode if needed on secondary CPU
ARM: dts: am437x-gp-evm: Do not reset gpio5
ARM: dts: omap3-igep0020: use SMSC9221 timings
PCI: mvebu: split PCIe BARs into multiple MBus windows when needed
...
With the addition of clock-indices, we need to change the renesas
clock implementation to use these instead of the local definition
of "renesas,clock-indices".
Since this will break booting with older device trees, we add a
simple auto-detection of which properties are present.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
<uapi/asm/inst.h> is exported to userland so the macro name BITFIELD_FIELD
pollutes the namespace. Prefix the name with __ fixes this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson2 has been using (incorrectly) kHz for cpu_clk rate. This has
been unnoticed, as loongson2_cpufreq was the only place where the rate
was set/get. After commit 652ed95d5f
(cpufreq: introduce cpufreq_generic_get() routine) things however broke,
and now loops_per_jiffy adjustments are incorrect (1000 times too long).
The patch fixes this by changing cpu_clk rate to Hz.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: stable@vger.kernel.org
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: cpufreq@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Patchwork: https://patchwork.linux-mips.org/patch/6678/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 0e476d9124 ("MIPS: Loongson: Add Loongson-3 Kconfig options")
added "select GENERIC_HARDIRQS_NO__DO_IRQ". But the Kconfig symbol
GENERIC_HARDIRQS_NO__DO_IRQ was already removed in v2.6.38, so that
select is a nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6677/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change reverts most of commit
60724ca59e [MIPS: IP checksums: Remove
unncessary .set pseudos] that introduced warnings with the
CPU_DADDI_WORKAROUNDS option set:
arch/mips/lib/csum_partial.S: Assembler messages:
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:467: Warning: used $3 with ".set at=$3"
[...]
arch/mips/lib/csum_partial.S:577: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:577: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:577: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:601: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:601: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:601: Warning: used $3 with ".set at=$3"
arch/mips/lib/csum_partial.S:601: Warning: used $3 with ".set at=$3"
[and so on, and so on...]
The warnings are benign and good code is produced regardless because no
macros that'd use the assembler's temporary register are involved, however
the `.set noat' directives removed by the commit referred are crucial to
guarantee this is still going to be the case after any changes in the
future. Therefore they need to be brought back to place which this
change does.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6686/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This corrects assembler warnings and broken code generated in
__strncpy_from_user_asm:
arch/mips/lib/strncpy_user.S: Assembler messages:
arch/mips/lib/strncpy_user.S:52: Warning: Macro instruction expanded into
multiple instructions in a branch delay slot
with the CPU_DADDI_WORKAROUNDS option set. The function schedules delay
slots manually where there is really no need to as GAS is happy to do it
all itself, so undo it all and remove `.set noreorder'.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6685/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With CPU_DADDI_WORKAROUNDS enabled __delay assembles with a macro in a
branch delay slot:
{standard input}: Assembler messages:
{standard input}:18: Warning: Macro instruction expanded into multiple
instructions in a branch delay slot
and broken code results:
0000000000000000 <__delay>:
0: 1480ffff bnez a0,0 <__delay>
4: 24010001 li at,1
8: 0081202f dsubu a0,a0,at
c: 03e00008 jr ra
10: 00000000 nop
14: 00000000 nop
Consequently the function loops indefinitely, showing up prominently as a
hang in the delay loop calibration at bootstrap.
This change corrects the problem by forcing the immediate 1 into a
register while keeping code produced identical where CPU_DADDI_WORKAROUNDS
is disabled.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6669/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 231a35d372 [[MIPS] RM: Collected
changes] broke DECstation support by introducing an incompatible copy of
arch/mips/dec/prom/call_o32.S in arch/mips/fw/lib/, built unconditionally.
The copy happens to land earlier of the two among the modules used in the
link and is therefore chosen for the DECstation rather than the intended
original. As a result random kernel data is corrupted because a pointer
to the "%s" formatted output template is used as a temporary stack pointer
rather than being passed down to prom_printf. This also explains why
prom_printf still works, up to a point -- the next argument is the actual
string to output so it works just fine as the output template until enough
kernel data has been corrupted to cause a crash.
This change adjusts the modified wrapper in arch/mips/fw/lib/call_o32.S to
let callers request no stack switching by passing a null temporary stack
pointer in $a1, reworks the DECstation callers to work with the updated
interface and removes the old copy from arch/mips/dec/prom/call_o32.S. A
few minor readability adjustments are included as well, most importantly
O32_SZREG is now used throughout where applicable rather than hardcoded
multiplies of 4 and $fp is used to access the argument save area as a more
usual register to operate the stack with rather than $s0.
Finally an update is made to the temporary stack space used by the SNI
platform to guarantee 8-byte alignment as per o32 requirements.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6668/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 69f24d1784 [MIPS: Optimize
current_cpu_type() for better code.] missed an update for two DECstation
bus error support files that now do not build, this is a fix.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6667/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add mailing list and patchwork URL so patches now have a defined path.
Also add myself as a TURBOchannel maintainer. However Maciej is going
to the the resident TURBOchannel guru.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: "Maciej W. Rozycki" <macro@linux-mips.org>
Reverts commit 795038a691 because
d6d3c9afaa provides the same functionality
in a more generic way. Both patches applied however means that the
VPE and TC IDs get printed twice currently.
According to Reference Manual -- ESAI Initialization chapter, as the
standard procedure of ESAI personal reset, the PCRC and PRRC registers
should be remained in its reset value and then configured after T/RCCR
and T/RCR configurations's done but before TE/RE's enabling.
So this patch moves PCRC and PRRC settings to the end of hw_params().
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ESAI can only output EXTAL clock source directly. But for FSYS clock source,
ESAI can not output it without getting through PSR PM dividers.
So this patch adds an extra check in the code.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The range here from 1 to 16 is confined to FP divider only while the
sck_div indicates if the calculation contains PSR and PM dividers. So
for the case using PSR and PM since the sck_div is true, the range of
ratio would simply become bigger than 16.
So this patch fixes the condition here and adds one line comments to
make the purpose here clear.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently when the DAPM context bias level is SUSPEND and the target bias level
is OFF dapm_pre_sequence_async() will first transition to PREPARE and
dapm_post_sequence_async() will then transition back from PREPARE to STANDBY and
then to OFF.
This patch makes sure that dapm_pre_sequence_async() only transitions to PREPARE
when either going to ON or away from ON. This avoids the extra unnecessary
transitions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case we are doing DMA transfer and the size of the buffer is not multiple
of 4 bytes the driver truncates that to 4-byte boundary and tries to handle
remaining bytes using PIO.
Or that is what it tried to do. What actually happens is that it calls
ALIGN() to the buffer size which aligns it to the next 4-byte boundary
(doesn't truncate). Doing this results 1-3 bytes extra to be transferred.
Furthermore we handle remaining bytes using PIO which results one extra
byte to be transferred. In worst case the driver transfers 4 extra bytes.
While investigating this it turned out that the DMA hardware doesn't even
have such limitation so we can solve this by dropping the code that tries
to handle unaligned bytes.
Reported-by: Chiau Ee Chew <chiau.ee.chew@intel.com>
Reported-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC to CODEC DAI links the paths are created in snd_soc_dapm_new_pcm().
Also for CODEC to CODEC links the widgets are connected cross-over via a DAI
link widget, meaning that the capture widget of one CODEC will be connected to
the playback widget of the other and vice versa. Whereas
snd_soc_dapm_connect_dai_link_widgets() directly connects the playback widget of
the CPU DAI to the playback widget of the CODEC DAI and the capture widget of
the CPU DAI to the capture widget of the CODEC DAI. So not skipping
CODEC<->CODEC links in snd_soc_dapm_connect_dai_link_widgets() will create
incorrect connections between the two CODECs which will cause DAPM to detect
active paths where there are none and unnecessarily power up widgets.
Fixes: b893ea5 ("ASoC: sapm: Automatically connect DAI link widgets in DAPM graph.")
Cc: <stable@vger.kernel.org> (for 3.14+)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The regular state before we execute SNDRV_PCM_TRIGGER_SUSPEND should be
SNDRV_PCM_TRIGGER_START, not SNDRV_PCM_TRIGGER_STOP. Thus fix it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The datasheet for EMC1413/EMC1414, which is fully compatible to
EMC1403/1404 and uses the same chip identification, references revision
numbers 0x01, 0x03, and 0x04. Accept the full range of revision numbers
from 0x01 to 0x04 to make sure none are missed.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Cc: stable@vger.kernel.org
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 454aee17f claims to convert driver emc1403 to use
devm_hwmon_device_register_with_groups, however the patch itself makes
use of hwmon_device_register_with_groups instead. As the driver remove
function was still dropped, the hwmon device is no longer unregistered
on driver removal, leading to a resource leak.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 454aee17f hwmon: (emc1403) Convert to use devm_hwmon_device_register_with_groups
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org [3.13+]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Attempts to set the hysteresis value to a temperature below the target
limit fails with "write error: Numerical result out of range" due to
an inverted comparison.
Signed-off-by: Josef Gajdusek <atx@atx.name>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org
[Guenter Roeck: Updated headline and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 01f8fa4f01d8("genirq: Allow forcing cpu affinity of interrupts")
enabled the forced irq_set_affinity which previously refused to route an
interrupt to an offline cpu.
Commit ffde1de64012("irqchip: Gic: Support forced affinity setting")
implements this force logic and disables the cpu online check for GIC
interrupt controller.
When __cpu_disable calls migrate_irqs, it disables the current cpu in
cpu_online_mask and uses forced irq_set_affinity to migrate the IRQs
away from the cpu but passes affinity mask with the cpu being offlined
also included in it.
When calling irq_set_affinity with force == true in a cpu hotplug path,
the caller must ensure that the cpu being offlined is not present in the
affinity mask or it may be selected as the target CPU, leading to the
interrupt not being migrated.
This patch uses cpu_online_mask when using forced irq_set_affinity so
that the IRQs are properly migrated away.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
virt_to_pfn has been defined in arch/arm/include/asm/memory.h by commit
e26a9e0 "ARM: Better virt_to_page() handling" and Xen has come to rely
on it. Introduce virt_to_pfn on arm64 too.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
If the kernel is built to support multi-ARM configuration with shmobile
support built in, then drivers/sh is not built. This contains the PM
runtime code in drivers/sh/pm_runtime.c, which implicitly enables the
module clocks for all devices, and thus is quite essential.
Without this, the state of clocks depends on implicit reset state, or on
the bootloader.
If ARCH_SHMOBILE_MULTI then build the drivers/sh directory, but ensure that
bits that may conflict (drivers/sh/clk if the common clock framework is
enabled) or are not used (drivers/sh/intc), are not built.
Also, only enable the PM runtime code when actually running on a shmobile
SoCs that needs it.
ARCH_SHMOBILE_MULTI was added a while ago by commit
efacfce5f8 ("ARM: shmobile: Introduce
ARCH_SHMOBILE_MULTI"), but drivers/sh was compiled for both
ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI until commit
bf98c1eac1 ("ARM: Rename ARCH_SHMOBILE to
ARCH_SHMOBILE_LEGACY").
Inspired by a patch from Ben Dooks <ben.dooks@codethink.co.uk>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
I am seeing an issue where a CPU running perf eventually hangs.
Traces show timer interrupts happening every 4 seconds even
when a userspace task is running on the CPU. /proc/timer_list
also shows pending hrtimers have not run in over an hour,
including the scheduler.
Looking closer, decrementers_next_tb is getting set to
0xffffffffffffffff, and at that point we will never take
a timer interrupt again.
In __timer_interrupt() we set decrementers_next_tb to
0xffffffffffffffff and rely on ->event_handler to update it:
*next_tb = ~(u64)0;
if (evt->event_handler)
evt->event_handler(evt);
In this case ->event_handler is hrtimer_interrupt. This will eventually
call back through the clockevents code with the next event to be
programmed:
static int decrementer_set_next_event(unsigned long evt,
struct clock_event_device *dev)
{
/* Don't adjust the decrementer if some irq work is pending */
if (test_irq_work_pending())
return 0;
__get_cpu_var(decrementers_next_tb) = get_tb_or_rtc() + evt;
If irq work came in between these two points, we will return
before updating decrementers_next_tb and we never process a timer
interrupt again.
This looks to have been introduced by 0215f7d8c5 (powerpc: Fix races
with irq_work). Fix it by removing the early exit and relying on
code later on in the function to force an early decrementer:
/* We may have raced with new irq work */
if (test_irq_work_pending())
set_dec(1);
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
