On CNL we may need to bump up the system agent voltage not only due
to CDCLK but also when driving DDI port with a sufficiently high clock.
To that end start tracking the minimum acceptable voltage for each crtc.
We do the tracking via crtcs because we don't have any kind of encoder
state. Also there's no downside to doing it this way, and it matches how
we track cdclk requirements on account of pixel rate.
v2: Allow disabled crtcs to use the min voltage
Add IS_CNL check to intel_ddi_compute_min_voltage() since
we're using CNL specific values there
s/intel_compute_min_voltage/cnl_compute_min_voltage/ since
the function makes hw specific assumptions about the voltage
values
v3: Drop the test hack leftovers from skl_modeset_calc_cdclk()
v4: s/voltage/voltage_level/ (Rodrigo)
Replace DPLL DVFS FIXMEs with an explanation why we don't
do anything there (Rodrigo)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-9-ville.syrjala@linux.intel.com
As we faced in BXT, on CNL DDI_A_4_LANES is not
set as expected when system is boot with multiple
monitors connected. This result in wrong lane
setup impacting the max data rate available and
consequently blocking modeset on eDP, resulting
in a blank screen.
Most of CNL SKUs don't support DDI-E.
The only SKU that supports DDI-E is the same
that supports the full A/E split called DDI-F.
Also when DDI-F is used DDI-E cannot be used because
they share Interrupts. So DDI-E is almost useless.
Anyways let's consider this is possible and rely on
VBT for that.
This patch was initialy start by Clint, but required
many changes including full commit message. So
Credits entirely to Clint for finding this.
v2: Extract all messy conditions into a helper function
as suggested by Ville.
Along with simplification I removed the debug
message on the working case since now all conditions
are grouped.
v3: Split the conditions even more as suggested by Ville.
Get's cleaner and easier to add new cases in the
future.
Suggested-by: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023173920.22890-1-rodrigo.vivi@intel.com
No functional change expected. Just let's use this enum
when possible and also same standard pll_id name
so we can rework gen9+ port clock later.
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018195407.8618-1-rodrigo.vivi@intel.com
A bunch of functions are now exclusively used for HDMI, so naming the
variables with hdmi prefix/suffix is redundant. Also use int rather
than u32 for the translation level consistently.
v2: Rebase due to hdmi_level=-1 avoidance
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018181958.4423-1-ville.syrjala@linux.intel.com
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Handle missing buf trans tables, or out of bounds buf trans levels
the same way everywhere. These should never be hit under normal
conditions, but let's play it safe for now.
v2: Avoid the hdmi_level=-1 case (James)
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018181934.4229-1-ville.syrjala@linux.intel.com
Reviewed-by: James Ausmus <james.ausmus@intel.com>
SKL DDI B/C/D only have 9 usable buf trans registers for DP/eDP. That
matches the normal DP buf trans tables, but the low vswing eDP tables
have 10 entries. Thus the eDP tables can only be used safely with DDI A
and E.
We try to catch cases where DDI B/C/D gets used with the wrong number of
entires in some parts of the code, but not everywhere. Let's move the
code to deal with that deeper into intel_ddi_get_buf_trans_edp(). And
for sake of symmetry do the same in intel_ddi_get_buf_trans_dp(). That
would also avoid explosions in the rather unlikely case that the DP
tables would get revised to 10 entries as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-9-ville.syrjala@linux.intel.com
Reviewed-by: James Ausmus <james.ausmus@intel.com>
default_index contained in the BXT buf_trans tables is actually useless.
For DP we should always have a valid level selected (otherwise the link
training logic would be buggy), and for HDMI we can just do what the
other platforms do and pick the correct entry in intel_ddi_hdmi_level().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-8-ville.syrjala@linux.intel.com
Reviewed-by: James Ausmus <james.ausmus@intel.com>
encoder->type is unreliable for DP/HDMI, so pass it in explicity into
cnl_ddi_vswing_sequence(). This matches what we do for BXT.
v2: Pass intel_encoder down to cnl_ddi_vswing_program(), and
clean up the argument types while at it
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-7-ville.syrjala@linux.intel.com
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Make BXT less special by following the CNL approach and handling
it in intel_ddi_dp_voltage_max() alognside every other DDI platform.
v2: Clean up the argument types to bxt_ddi_vswing_sequence() while at it
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-6-ville.syrjala@linux.intel.com
Reviewed-by: James Ausmus <james.ausmus@intel.com>
encoder->type isn't reliable for DP/HDMI encoders, so pass the type
explicity to skl_set_iboost(). Also take the opportunity to streamline
the code.
v2: Clean up the argument types to skl_ddi_set_iboost() while at it
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-4-ville.syrjala@linux.intel.com
Reviewed-by: James Ausmus <james.ausmus@intel.com>
We'll want to use the intel_ddi_get_buf_trans_*() functions a bit
earlier in the file, so move them up. While at it start using them
in the iboost setup to get rid of the platform checks there.
v2: Rebase due to BDW FDI buf trans fix
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-2-ville.syrjala@linux.intel.com
Reviewed-by: James Ausmus <james.ausmus@intel.com>
On PLL Enable sequence we need to "Configure DPCLKA_CFGCR0 to turn on
the clock for the DDI and map the DPLL to the DDI"
So we first do the map and then we unset DDI_CLK_OFF to turn the clock
on. We do this in 2 separated steps.
However, on this second step where we should only unset the off bit we are
also unmapping the ddi from the pll. So we end up using the pll 0
for almost everything. Consequently breaking cases with more than one
display.
Fixes: 555e38d273 ("drm/i915/cnl: DDI - PLL mapping")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Kahola, Mika <mika.kahola@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003220859.21352-2-rodrigo.vivi@intel.com
The compiler warns:
drivers/gpu/drm/i915/intel_ddi.c:118:35: warning: ‘bdw_ddi_translations_fdi’ defined but not used
Lo and behold, if we look at intel_ddi_get_buf_trans_fdi(), it uses
hsw_ddi_translations_fdi[] for both Haswell and *Broadwell*
Fixes: 7d1c42e679 ("drm/i915: Refactor code to select the DDI buf translation table")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.12+
Link: https://patchwork.freedesktop.org/patch/msgid/20171013154735.27163-1-chris@chris-wilson.co.uk
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Rather that plumb the link parameters separately to
intel_ddi_pre_enable_dp() let's just pass the entire crtc state.
intel_ddi_pre_enable_hdmi() already took the crtc state, but for some
reason intel_ddi_pre_enable() still wanted to extract has_infoframe
from therein and pass it in separately. Let's not do that since it's
pointless.
v2: Rebase due to more code getting pulled into the DDI hooks
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
To untangle the mess that is intel_ddi_post_disable() move the the bits
needed by FDI into intel_ddi_fdi_post_disable(). This way we can stop
worrying about FDI in intel_ddi_post_disable().
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-5-ville.syrjala@linux.intel.com
Extract the code to disable the DDI_BUF_CTL into small helper. This
will allows us to detangle the encoder type mess in
intel_ddi_post_disable().
v2: Keep using intel_ddi_get_encoder_port() for now
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-4-ville.syrjala@linux.intel.com
Pull the code to disable the port clock into a function. We already have
the intel_ddi_clk_select() counterpart.
v2: Keep using intel_ddi_get_encoder_port() for now (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010121207.570-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
If for some unexpected reason the registers all read zero it's better
to WARN and return instead of dividing by zero and completely freezing
the machine.
I don't expect this to happen in the wild with the current code, but I
accidentally triggered the division by zero while doing some debugging
in an unusual environment.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171005213842.11423-2-paulo.r.zanoni@intel.com
One of the recent changes introduced a warning about
undefined behavior in the sanity checking:
drivers/gpu/drm/i915/intel_ddi.c: In function 'intel_ddi_hdmi_level':
drivers/gpu/drm/i915/intel_ddi.c:654:6: error: 'n_hdmi_entries' may be used uninitialized in this function [-Werror=maybe-uninitialized]
It seems that the new cnl specific get_buf_trans functions
can return uninitialized data if the voltage level is set
to an unexpected value. This changes the code to always return
'1' in that error case, which seems like the safest choice
as we use one less than the number as an array index later on.
Fixes: cc9cabfdec ("drm/i915/cnl: Move voltage check into ddi buf trans functions.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[danvet: shut up gcc comment added.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171005120835.437022-1-arnd@arndb.de
Use the POWER_DOWN_PHY and POWER_UP_PHY sideband message transactions to
set power states for downstream sinks. Apart from giving us the ability
to set power state for individual sinks, this fixes the below test for
me.
$ xrandr --display :0 --output DP-2-2-8 --off
$ xrandr --display :0 --output DP-2-2-1 --off
$ xrandr --display :0 --output DP-2-2-8 --auto #Black screen
$ xrandr --display :0 --output DP-2-2-1 --auto
v2: Modify and document the dpms and port disable order (Ville)
Add comment explaining is_mst = !crtc_state equivalence(Ville, Maarten)
v3 by Jani: rebase
References: https://bugs.freedesktop.org/show_bug.cgi?id=90963
References: https://bugs.freedesktop.org/show_bug.cgi?id=88124
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude <lyude@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003142211.860-1-jani.nikula@intel.com
The common lane power down flag of a DPIO PHY has a funky semantic:
after the initial enabling of the PHY (so from a disabled state) this
flag will be clear. It will be set only after the PHY will be used for
the first time (for instance due to enabling the corresponding pipe) and
then become unused (due to disabling the pipe). During the initial PHY
enablement we don't know which of the above phases we are in, so move
the check for the flag where this is known, the HW readout code. This is
where the rest of lane power down status checks are done anyway.
This fixes at least a problem on GLK where after module reloading, the
common lane power down flag of PHY1 is set, but the PHY is actually
powered-on and properly set up. The GRC readout code for other PHYs will
hence think that PHY1 is not powered initially and disable it after the
GRC readout. This will cause the AUX power well related to PHY1 to get
disabled in a stuck state, timing out when we try to enable it later.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Fixes: e93da0a013 ("drm/i915/bxt: Sanitiy check the PHY lane power down status")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102777
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171002135307.26117-1-imre.deak@intel.com
No functional changes. Only change the macro from
"DPLL_CFGCR0_DC0_FRAC_SHIFT to DPLL_CFGCR0_DCO_FRACTION_SHIFT
to be consistent with DPLL_CFGCR0_DCO_FRACTION_MASK
and DPLL_CFGCR0_DCO_FRACTION
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1505413899-30876-1-git-send-email-manasi.d.navare@intel.com
On clock recovery this function is called to find out
the max voltage swing level that we could go.
However gen 9 functions use the old buffer translation tables
to figure that out. That table is not valid for CNL
causing an invalid number of entries and an invalid selection
on the max voltage swing level.
v2: Let's use same approach that previous platforms.
v3: Actually use n_entries and avoid duplicated -1.
v4: Avoid cnl_max_level and use current style.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170831145356.15932-1-rodrigo.vivi@intel.com
Let's get a proper HDMI DDI entry level for vswing programming
sequences on CNL.
Spec doesn't specify any default for HDMI tables,
so let's pick the last entry as the default for now.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-7-rodrigo.vivi@intel.com
No functional changes. But those functions will be needed
to get max level for HDMI and DP, so let's move those
up closer to other similar functions existent for previous
platforms.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-6-rodrigo.vivi@intel.com
Let's start converging CNL buf translations to same style
used on previous platforms. So first thing is to use the
standard signature so we don't need to propagate the voltage
check into other parts of the code, but only on the parts
that it is really useful.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-5-rodrigo.vivi@intel.com
Sequences for DisplayPort asks us to
" Configure voltage swing and related IO settings.
Refer to DDI Buffer section."
before "Configure and enable DDI_BUF_CTL"
On BXT and CNL this means to execute the ddi vswing sequences.
At this point these sequences calls are getting duplicated for DP
because they are all called from DP link trainning sequences.
However this patch is not yet removing it before a futher discussion
since spec also allows that during link training without disabling
anything:
"
Notes
Changing voltage swing during link training:
Change the swing setting following the DDI Buffer section.
The port does not need to be disabled.
"
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-4-rodrigo.vivi@intel.com
Vswing sequences on BXT and CNL are equivalent
to the ddi buffer registers setting on other platforms.
For some reason it got aligned with skl_ddi_set_iboost what
is semantically incorrect. This forced us to keep skipping
ddi buffer translation tables on the platforms that has
the vswing sequences.
v2: Don't mess with DP signal levels on this patch.
Cc: Vandana Kannan <vandana.kannan@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-3-rodrigo.vivi@intel.com
Let's decouple bxt, glk and cnl dp signal levels
from other DDIs to avoid confusion.
No functional change. Only a reorg to avoid messing
with currently working DP signal levels when
moving voltage swing sequences around to match spec.
v2: ddi_signal_levels is also called from other ddi
platforms, so don't remove IS_GEN9_BC check from
skl_ddi_set_iboos. (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-2-rodrigo.vivi@intel.com
No functional changes. This only moves the DP level
selection to a separated function that will be later
used to organize better the vswing sequences.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170829232230.23051-1-rodrigo.vivi@intel.com
The enable/disable/etc. encoder hooks aren't supposed to alter the
state(s), so pass them as const. Unfortunately C lacks any kind of deep
const thingy, so this can't catch all abuses. But at least it acts as a
hint to the reader telling them not to mess about with the state(s).
v2: Update intel_tv_mode_find() and ironlake_edp_pll_on() as well
v3: Deal with intel_sdvo_connector_state
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-9-ville.syrjala@linux.intel.com
The PSR enable/disable need to know things about the crtc state, so
plumb it through. This will become even more important when we start
to reuse the generic infoframe code for the VSC DIP programming as the
infoframe code wants the crtc state as well.
v2: Fix kernel docs
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-7-ville.syrjala@linux.intel.com
DP ports may want to use the video DIP for SDP transmission, so let's
initialize the vfuncs for DP encoders as well. The only exception is
port A eDP prior to HSW as that one doesn't have a video DIP instance.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170818134958.15502-6-ville.syrjala@linux.intel.com
Disabling the video DIP when shutting the port down seems like a good
idea.
Bspec says:
"When disabling both the DIP port and DIP transmission,
first disable the port and then disable DIP."
and
"Restriction : GCP is only supported with HDMI when the bits per color is
not equal to 8. GCP must be enabled prior to enabling TRANS_DDI_FUNC_CTL
for HDMI with bits per color not equal to 8 and disabled after disabling
TRANS_DDI_FUNC_CTL"
So let's do it in the .post_disable() hook.
v2: Remove double "dpms off" caused by rebase fail
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170822140914.24413-1-ville.syrjala@linux.intel.com
For 0.85V cnl_get_buf_trans_edp() returns the DP table, instead of EDP.
Use the correct table.
The error was pointed out by this clang warning:
drivers/gpu/drm/i915/intel_ddi.c:392:39: warning: variable
'cnl_ddi_translations_edp_0_85V' is not needed and will not be emitted
[-Wunneeded-internal-declaration]
static const struct cnl_ddi_buf_trans cnl_ddi_translations_edp_0_85V[] = {
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170717195854.192139-1-mka@chromium.org
The condition for setting the Loadgen Select bit of
PORT_TX_DW4 register during DDI Vswing Sequence should be
Bit rate <=6 GHz whereas the existing code checks only
Bit Rate < 6GHz. This patch fixes this condition.
While at it also remove the redundant paranthesis.
Fixes: cf54ca8bc5 ("drm/i915/cnl: Implement voltage swing sequence.")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500329122-32662-1-git-send-email-manasi.d.navare@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get HDMI YCBCR420 output, the PIPEMISC register should be
programmed to:
- Generate YCBCR output (bit 11)
- In case of YCBCR420 outputs, it should be programmed in full
blend mode to use the scaler in 5x3 ratio (bits 26 and 27)
This patch:
- Adds definition of these bits.
- Programs PIPEMISC for YCBCR420 outputs.
- Adds readouts to compare HW and SW states.
V2: rebase
V3: rebase
V4: rebase
V5: added r-b from Ander
V6: Handle only YCBCR420 outputs (ville)
V7: rebase
V8: Addressed review comments from Ville
- Add readouts for state->ycbcr420 and 420 pixel_clock.
- Handle warning due to mismatch in clock for ycbcr420 clock.
- Rename PIPEMISC macros to match the Bspec.
- Add a debug print stating if YCBCR 4:2:0 output enabled.
Added r-b from Ville
V9: Addressed review comments from Imre:
- Add 420 mode clock adjustment in intel_hdmi_mode_valid to
prevent 420_only modes getting rejected for high clock.
- Add port clock adjustment for ycbcr420 modes in ddi_get_clock
- Rename macros as per Ville's suggestion.
- Remove unnecessary wl changes.
V10: Added r-b from Imre
V11: Fixed faulty dotclock handling, and addressed missing comment
from previous set of review comments (Imre)
V12: Fixed dotclock for 12bpc too, removed 420 check for GEN < 10
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1500904172-31717-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo had noticed that inside cnl_ddi_vswing_program
the case was handling voltage but with no indication
of type where a missing type could also take us to that
path. So my first attempt was to add a message to
let clear who trigger that path.
However DK had a better idea that is to handle the
missed type sooner before it might take to that path.
So this v2 here uses his approach.
v2: Handle missed type sooner.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170710205852.28352-1-rodrigo.vivi@intel.com
