There's no reason to set EXIT_PENDING when we
start removing the module, as mac80211 will
cleanly shut down the device in this case.
Additionally, there's no point in rejecting
commands to the device when we're cleaning up
as that only leads to unwanted errors from
mac80211 being printed, such as
failed to remove key (...) from hardware (-16)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of (ab)using the sta_lock, make the
transport layer lock its own TX queue data
structures with a lock per queue. This also
unifies with the cmd queue lock.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export it as "nic_error" notification, the error handling will be in
the op_mode.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This handler allows the transport layer to free an skb from the
op_mode. This can happen when the driver is stopped while Tx
packets are pending in the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of using a global lock, the PCIe transport
can use an own lock for its IRQ. This will make it
possible to not disable IRQs for the shared lock.
The lock is currently used throughout the code but
this can be improved even further by splitting up
the locking for the queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com>
The message was misleading when a queue is deactivated. The fifo
number is irrelevant then, so don't print it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
From now on, the transport layer in charge of providing access to the
device. So change all the driver to give a pointer to the transport
to all the low level functions that actually access the device.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This will allow us to catch bad cases in which the packets aren't in
the right place on the ring.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with the mapping of RA / TID to HW queues in AGG.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with tx AGG setup.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with tx AGG alloc.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tid_data is not related to the transport layer, so move
the logic that depends on it to the upper layer.
This patch deals with tx AGG stop.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In the same spirit as the previous patch. Eventually this will
allow us to remove the tid_data knowledge from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since packets sent to an RA / TID in AGG are sent from a
separate HW Tx queue, we may get into a race:
the regular queue isn't empty while we already begin to
send packets from the AGG queue. This would result in sending
packets out of order.
In order to cope with this, mac80211 waits until the driver
reports that the legacy queue is drained before it can send
packets to the AGG queue. During that time, mac80211 buffers
packets for the driver. These packets will be sent in order
after the driver reports it is ready.
The way this was implemented in the driver is as follows:
We held a counter that monitors the number of packets for
an RA / TID in the HW queues. When this counter reached 0,
we knew that the HW queues were drained and we reported to
mac80211 that were ready to proceed.
This patch changes the implementation described above. We
now remember what is the wifi sequence number of the first
packet that will be sent in the AGG queue (lets' call it
ssn). When we reclaim the packet before ssn, we know that
the queue is drained, and we are ready to proceed.
This will allow us to move this logic in the upper layer and
eventually remove the tid_data from the shared area.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Remove this redundancy.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some information was redundation, other was missing.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users complain that the traffic gets stalled sometimes. This will
allow easier debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Warning introduced by c847474b7dfdda304d0d8ffcc5a9db546b1cb3e9
iwlwifi: check status before send command
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check the status before sending host command, if any of the condition
match, cancel the host command before queue
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station is associated with an AP and the RF_KILL switch is engaged,
numerous error messages were sent to the system log. The error messages
were the result of the failure(s) of the various submodules to perform
their tasks after the radios were disabled.
To resolve this situation, the messages were modified to use a new macro,
IWL_DEBUG_QUIET_RFKILL. This macro allows for the RF_KILL error messages
to be sent to the log provided that IWL_DEBUG is true and IWL_DL_RADIO
is '1'. For all other cases, the error messages resulting from an RFKILL
event will not be sent to the system log. Messages logged because of an
RFKILL will be tagged with the prefix '(RFKILL)' to clarify the cause of
the error.
Signed-off-by: Todd Previte <toddX.a.previte@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl-core.c and iwl-trans-pcie-tx.c don't need to include iwl-dev.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move iwl_enable_rfkill_int to iwl-core.h, and remove the empty
iwl-helpers.h
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When detect wrong state on shutdown aggregation queue, show more
information for debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disable aggregation request come in on wrong agg state. ignore it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For error condition, STATUS_HCMD_ACTIVE already got clear before receive
tx cmd complete, give warning
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When detect cmd queue time out, display the current read/write pointer
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This simplifies both the transport layer and the upper layer.
Kill the union in the device command, which avoids the funny syntax
we had: cmd->cmd.payload.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before this patch, the upper layer could register a callback for each
host command. This mechanism allowed the upper layer to have
different callbacks for the same command ID. In fact, it wasn't used
and the rx_handlers is enough: same callback for all the command with
a specific command ID.
The iwl_send_add_station needs the access the command that was sent
while handling the response (regardless if the command was sent in
SYNC or ASYNC mode). So now, all the handlers receive the host
command that was sent. This implies a change in the handler signature.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
re-apply the unsigned shorts bug fixed by Dan Carpenter but get lost
after the file move.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the dawn of its time, iwlwifi has used
interruptible waits to wait for synchronous
commands and firmware loading.
This leads to "interesting" bugs, because it
can't actually handle the interruptions; for
example when a command sending is interrupted
it will assume the command completed fully,
and then leave it pending, which leads to all
kinds of trouble when the command finishes
later.
Since there's no easy way to gracefully deal
with interruptions, fix the driver to not use
interruptible waits.
This at least fixes the error
iwlagn 0000:02:00.0: Error: Response NULL in 'REPLY_SCAN_ABORT_CMD'
I have seen in P2P testing, but it is likely
that there are other errors caused by this.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: stable@kernel.org [2.6.24+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have the transport layer have a
callback for iwl_trans_send_cmd_pdu() since it is
just a generic wrapper around iwl_trans_send_cmd().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all the PCI-E specific transport files to
be iwl-trans-pcie*; specifically iwl-trans.c
which is really iwl-trans-pcie.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
