Enable ap_ps_peer_param_cmdid for 10.x FW.
This is used mainly for AP UAPSD.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Reduce the Rx count threshold to make sure we read
the available credits for Tx.
Signed-off-by: Julien Massot <jmassot@aldebaran-robotics.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With the previous value (1700), some urb are dropped
with a babble error (urb status equal -EOVERFLOW).
These error seems to only happen when urb length is a
multiple of packet size (512).
Signed-off-by: Julien Massot <jmassot@aldebaran-robotics.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The call to clamp_t() first truncates the variable signed 8 bit and as a
result, the actual clamp is a no-op.
Fixes: 0d78156eef ('p54: improve site survey')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete a variable that is at most only assigned to a constant, but never
used otherwise.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.
Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).
This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This would be useful when debugging RX performance issues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, rename node_stat to node_aggr.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.
This patch also fixes a typo in a comment.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
--snip--
Chain exists of:
rtnl_mutex --> misc_mtx --> rfkill_global_mutex
The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.
Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver ignores BSS_CHANGED_TXPOWER changes.
Fix this by calling ACX_TX_POWER when appropriate.
Signed-off-by: Alex Gal <a.gal@motsai.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding new device IDs and assigning generic function/variable
names instead of using device-id specific names.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The REGULATORY_CUSTOM_REG can be used during early init with
the goal of overriding the wiphy's default regulatory settings
in case the alpha2 of the device is not known. In the case that
the alpha2 becomes known lets avoid having drivers having to
clear the REGULATORY_CUSTOM_REG flag by doing it for them
when regulatory_hint() is used.
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath wants to first apply the custom regd and only later
will it revert to not using it if an alpha2 regulatory
domain is found. Since the wireless core now enforces
usage of the REGULATORY_CUSTOM_REG strictly when
wiphy_apply_custom_regulatory() is used this makes
ath adhere to the expected behaviour but also updates
the wiphy after its done with the custom usage.
This fixes this warning:
[ 5.488733] ath: phy0: ASPM enabled: 0x43
[ 5.488735] ath: EEPROM regdomain: 0x0
[ 5.488736] ath: EEPROM indicates default country code should be used
[ 5.488736] ath: doing EEPROM country->regdmn map search
[ 5.488737] ath: country maps to regdmn code: 0x3a
[ 5.488737] ath: Country alpha2 being used: US
[ 5.488738] ath: Regpair used: 0x3a
[ 5.488738] ------------[ cut here ]------------
[ 5.488745] WARNING: CPU: 0 PID: 161 at
/home/sujith/dev/wireless-testing/net/wireless/reg.c:1361
wiphy_apply_custom_regulatory+0x17a/0x1b0 [cfg80211]()
[ 5.488746] wiphy should have REGULATORY_CUSTOM_REG
The wireless core can *later* lift this flag for us for when
using the regulatory_hint() to make this fix more generic.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restore the original regulatory testing functionality and also
make it more flexible by allowing the parameters to be specified
when creating a dynamic radio.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new commands to the hwsim generic netlink family to allow
creating and destroying radios on the fly. The number of channels
a radio supports can be specified when it's created, if it isn't
the module parameter will be used as default.
This should be extended in the future to allow other parameters
to be specified, e.g.
* list of channels
* interface combinations, particularly P2P_DEVICE support
* regtest
* and pretty much all other hardware capabilities
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reject wmediumd registrations when any devices have multi-channel
capability, but register the generic netlink family unconditionally
to make it possible to add new commands that shouldn't depend on
the number of (default) channels.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There can't be two wmediumd instances controlling hwsim,
so reject registration from a second one and verify in
the commands that it's the correct instance calling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will make the next patch, adding support for netlink,
smaller and more readable. The code is not modified here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To later allow dynamic registration, assign the index for the
struct device and MAC address from a new free-running counter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the flag that the module parameter sets instead, so
later radios can use different parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the radio cleanup into a new function to later
allow deleting a single radio from the list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support dynamic radio registration in the future,
refactor the actual registration into a new function with only
minor cleanups. Since it had to change anyway, also clean up
the init error paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regtest thing worked based on the radio loop, but with
more dynamic radio registration that loop won't really exist
as is. We can add it back later with proper dynamic code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prepare the code to support, in theory, different devices
with a different number of channels supported. Right now
this doesn't really change anything, but will allow for
dynamic device registration in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to print a message, and genl_unregister_family()
can't really fail so remove the error message there as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add set_bitrate_mask callback. Currently
ath10k HW is limited to handle only single
fixed rate setting or limit number of used
spatial streams.
Example:
iw wlanX set bitrates legacy-5 ht-mcs-5 vht-mcs-5 2:9
will setup VHT, nss=2, mcs=9
iw wlanX set bitrates legacy-5 18 ht-mcs-5 vht-mcs-5
will setup legacy, 18Mbps
iw wlanX set bitrates legacy-5 ht-mcs-5 3 vht-mcs-5
will setup HT, nss=1, mcs=3
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9
will setup nss=1
iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9 2:0-9
will setup nss=2
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:
echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
And to put back firmare defaults use 0x0:
echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware can send simple ascii strings as debug messages using
WMI_DEBUG_PRINT_EVENTID, print those with ATH10K_DBG_WMI log level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.
10.X firmware support up to 127 peers, non-AP centric firmwares 16.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath10k is not using STA KICKOUT firmware functionality.
In order to avoid unwanted WMI_PEER_STA_KICKOUT_EVENT event this functionality
should be disabled when not used.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add Kconfig option that allow DFS functionality.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.
To avoid this, use the current channel information
maintained in the driver.
Cc: stable@vger.kernel.org
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add new AR9565 1.0/1.0.1/1.1 IDs
* Change Dell/Lenovo/Samsung cards to 2-Antenna with diversity.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having two copies of the code for device tree cfgdata
downloading, add a function to improve the code.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfgdata length exceeds the command buffer size we will end up
getting buffer overflow problem. Fix it by checking the buffer
size less the command header length.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as skb is ready to be reaped, prefetch 1-st cache line.
This accelerates data access that is performed later, during the
packet classification by the driver and IP stack.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit DMA_CFG_DESC_TX_OFFLOAD_CFG_L3T_IPV4_POS should be set for IPv4
only. Don't set it for IPv6
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use hardware capabilities to limit IRQ generation to about 15 per msec
It corresponds to about 7 packets/IRQ when running iperf with default
parameters at 1.3Gbps
Do not enable this feature in the sniffer (monitor) mode, because
interrupt moderation cause timestamp accuracy deterioration.
For the sniffer flow, it is important to get precise timestamp.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
