Add "ops" style method for using HDMI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to allow multiple display block in a video pipeline, we need to
give the drivers way to register themselves. For now we have
the omapdss_register_display() which is used to register panels, and
dss_register_output() which is used to register DSS encoders.
This patch makes dss_register_output() public (with the name of
omapdss_register_output), which can be used to register also external
encoders. The distinction between register_output and register_display
is that a "display" is an entity at the end of the videopipeline, and
"output" is something inside the pipeline.
The registration and naming will be made saner in the future, but the
current names and functions are kept to minimize changes during the dss
device model transition.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC needs to know the clock rate for DIGIT (i.e. TV) channel, and this
clock is provided by either VENC or HDMI modules. Currently DISPC will
call a function in VENC/HDMI, asking what the clock rate is. This means
we have a fixed dependency from DISPC to both VENC and HDMI.
To have a more generic approach, and in particular to allow adding OMAP5
HDMI driver, we need to remove this dependency. This patch makes
VENC/HDMI inform DISPC when the their clock changes, thus reversing the
dependency and removing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hpd_gpio is no longer used by the OMAP4 HDMI IP driver, and we can thus
remove the unnecessary code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TRM tells to set PHY to TXON only after getting LINK_CONNECT, and to
set PHY to OFF or LDOON after getting LINK_DISCONNECT, in order to avoid
damage to the PHY.
We don't currently do it quite like that. Instead of using the HDMI
interrupts, we use HPD signal. This works, but is not actually quite
correct, as HPD comes at a different time than LINK_CONNECT and
LINK_DISCONNECT interrupts. Also, the HPD GPIO is a property of the TPD
level shifter, not HDMI IP, so handling the GPIO in the HDMI driver is
wrong.
This patch implements the PHY power handling correctly, using the
interrupts.
There is a corner case that causes some additional difficulties: we may
get both LINK_CONNECT and LINK_DISCONNECT interrupts at the same time.
This is handled in the code by retrying: turning off the PHY, clearing
the interrupt status, and re-enabling the PHY. This causes a new
LINK_CONNECT interrupt to happen if a cable is connected.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently have omap_dss_device, which represents an external display
device, sometimes an external encoder, sometimes a panel. Then we have
omap_dss_output, which represents DSS's output encoder.
In the future with new display device model, we construct a video
pipeline from the display blocks. To accomplish this, all the blocks
need to be presented by the same entity.
Thus, this patch combines omap_dss_output into omap_dss_device. Some of
the fields in omap_dss_output are already found in omap_dss_device, but
some are not. This means we'll have DSS output specific fields in
omap_dss_device, which is not very nice. However, it is easier to just
keep those output specific fields there for now, and after transition to
new display device model is made, they can be cleaned up easier than
could be done now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_start_device() and omap_dss_stop_device(), called by the
DSS output drivers, are old relics. They originally did something
totally else, but nowadays they increase the module ref count for panels
that are enabled.
This model is quite broken: the panel modules may be used even before
they are enabled. For example, configuring the panel requires calls to
functions located in the panel modules.
In the following patches we try to improve the ref count management for
the modules and display devices. The first step, however, is to remove
the omap_dss_start/stop_device() totally.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In the future the "dssdev" parameter passed to output drivers will
change its meaning. Instead of being a pointer to the panel device, it's
a pointer to the output instance.
To make the transition easier, some of the uses for this dssdev
parameter can be easily removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss output drivers always read the platform data. This crashes when
there's no platform data when using DT.
Add a check to read the platform data only if it exists.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add proper error handling for hdmi_probe_pdata(). This will cause
EPROBE_DEFER to be properly passed upwards, causing the HDMI driver to be
probed again later if a resource was missing.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use platform_driver_register() instead of platform_driver_probe() so
that we can support EPROBE_DEFER.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use devm_clk_get() instead of clk_get() for dss, and for outputs hdmi
and venc. This reduces code and simplifies error handling.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DISPC channel used for each output is currently passed in panel
platform data from the board files.
To simplify this, and to make the panel drivers less dependent on OMAP,
this patch changes omapdss to resolve the channel independently. The
channel is resolved based on the OMAP version and, in case of DSI, the
DSI module id. This resolved channel is stored into a new field in
output, dispc_channel.
The few places where dssdev->channel was used are changed to use
output->recommended_channel. After this patch, dssdev->channel is
obsolete.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Add name field to omapdss's outputs so that in the following patches
panels refer to the output by their name. The name also helps debugging.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Move hdmi driver's output initialization a bit earlier, so that it
happens before hdmi panel init. In the future the hdmi panel will depend
on the output being ready.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
struct omap_dss_device contains HDMI clock divisors. The idea is that the
board file can pass precalculated divisors to the display driver.
However, these divsors are no longer needed, as the omapdss driver can
calculate the divisors during runtime.
This patch removes the divisors from omap_dss_device, and their uses
from the hdmi driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently attach an output to a dssdev in the initialization code for
dssdevices in display.c. This works, but doesn't quite make sense: an
output entity represents (surprisingly) an output of DSS, which is
managed by an output driver. The output driver also handles adding new
dssdev's for that particular output.
It makes more sense to make the output-dssdev connection in the output
driver. This is also in line with common display framework.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit 14840b9a83.
The commit breaks audio, and a new version will be applied later.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Normally the omapdss driver gets the regulators using the regulator
names assigned for omapdss. However, in an effort to get a minimal DSS
support for DT enabled kernel on selected boards, we will add omapdss
devices and platform data the old way even for DT kernel. This causes
the problem that omapdss cannot find the regulators using omapdss's
regulator names.
This patch creates a temporary workaround for DSI and HDMI by trying to
get the regulators also using native OMAP4 regulator names.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This function is now used in the driver init path to handle
probe errors properly. Thus, it may be possible to use this function
outside the exit path.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Creating the accessory devices, such as audio, from the HDMI driver
allows to regard HDMI as a single entity with audio an display
functionality. This intends to follow the design of drivers such
as MFD, in which a single entity handles the creation of the accessory
devices. Such devices are then used by domain-specific drivers; audio in
this case.
Also, this is in line with the DT implementation of HDMI, in which we will
have a single node to describe this feature of the OMAP SoC.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display must be uninitialized in order to free the requested GPIOs.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not blindly assume that the panel could be initialized.
While there, group mutex initialization at a single place.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Minor cleanup to give to the resource variable a more proper name.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.c currently exposes functions to configure the dispc source clock
and lcd source clock. There are configured separately from the output
drivers.
However, there is no safe way for the output drivers to handle dispc
clock, as it's shared between the outputs. Thus, if, say, the DSI driver
sets up DSI PLL and configures both the dispc and lcd clock sources to
that DSI PLL, the resulting dispc clock could be too low for, say, HDMI.
Thus the output drivers should really only be concerned about the lcd
clock, which is what the output drivers actually use. There's lot to do
to clean up the dss clock handling, but this patch takes one step
forward and removes the use of dss_select_dispc_clk_source() from the
output drivers.
After this patch, the output drivers only configure the lcd source
clock. On omap4+ the dispc src clock is never changed from the default
PRCM source. On omap3, where the dispc and lcd clocks are actually the
same, setting the lcd clock source sets the dispc clock source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi driver tries to find the given video timings from its static
list of timings, to find the required ID for the mode. The check tries
to find exact match for the pixel clock, among other checks.
with omapfb driver there can be some amount of error in the give pixel
clock, as the pixel clock is converted between Hz and ps, thus the
hdmi's check fails to find the mode.
This patch makes the check more allowing, by rounding the pixel clocks
to nearest MHz.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
This patch makes use of the hdmi_power_[on|off]_core() functions added
in the previous patch. The functions are used when reading EDID or
detecting if a monitor is connected.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
There's currently just one power-on function for HDMI, which enables the
IP and the video output. When reading EDID or detecting if a monitor is
connected, we don't need the video output.
Enabling the video output for these operations is not a big problem in
itself, but the quick enable/disable cycles caused by the operations
seem to cause sync lost errors from time to time. Also, this makes it
possible to read the EDID before the full video path has been set up.
This patch splits the hdmi_power_on into two parts, hdmi_power_on_core
and hdmi_power_on_full. The "full" version does what hdmi_power_on does
currently, and hdmi_power_on_core only enables the core IP. Similar
changes are made for power_off.
Note that these don't allow the HDMI IP to be first enabled, and later
enable the video output, but the HDMI IP will first need to be powered
off before calling the full version. So this is rather limited
implementation, but it fills the needs for reading EDID.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
Export dss_get_def_display_name() with the name of
omapdss_get_def_display_name() so that omapfb can use it after the next
patch which moves default display handling to omapfb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The output drivers get the omapdss hw version from the platform data for
their respective output device. This doesn't work with DT, as there's no
platform data for them.
Add a new function, omapdss_get_version(), which returns the dss version
from the core device, which will have platform data on DT also. The
function is exported so that users of omapdss can also use it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the missing unlock on the error handling path in function
hdmi_dump_regs().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With addition of output entities, a device connects to an output, and an output
connects to overlay manager. Replace the dssdev->manager references with
dssdev->output->manager to access the manager correctly.
When enabling the HDMI output, check whether the output entity connected to
display is not NULL.
Signed-off-by: Archit Taneja <archit@ti.com>
Add output structs to output driver's private data. Register output instances by
having an init function in the probes of the platform device drivers for
different outputs. The *_init_output for each output registers the output and
fill up the output's plaform device, type and id fields. The *_uninit_output
functions unregister the output.
In the probe of each interface driver, the output entities are initialized
before the *_probe_pdata() functions intentionally. This is done to ensure that
the output entity is prepared before the panels connected to the output are
registered. We need the output entities to be ready because OMAPDSS will try
to make connections between overlays, managers, outputs and devices during the
panel's probe.
Signed-off-by: Archit Taneja <archit@ti.com>
We currently create omap_dss_devices statically in board files, and use
those devices directly in the omapdss driver. This model prevents us
from having the platform data (which the dssdevs in board files
practically are) as read-only, and it's also different than what we will
use with device tree.
This patch changes the model to be in line with DT model: we allocate
the dssdevs dynamically, and initialize them according to the data in
the board file's dssdev (basically we memcopy the dssdev fields).
The allocation and registration is done in the following steps in the
output drivers:
- Use dss_alloc_and_init_device to allocate and initialize the device.
The function uses kalloc and device_initialize to accomplish this.
- Call dss_copy_device_pdata to copy the data from the board file's
dssdev
- Use dss_add_device to register the device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI and VENC outputs always use the DIGIT output from DISPC. The dssdev
struct contains "channel" field which is used to specify the DISPC
output for the display, but this was not used for HDMI and VENC.
This patch fills the channel field explicitely for HDMI and VENC
displays so that we can always rely on the channel field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have boards with multiple panel devices connected to the same
physical output, of which only one panel can be enabled at one time.
Examples of these are Overo, where you can use different daughter boards
that have different LCDs, and 3430SDP which has an LCD and a DVI output
and a physical switch to select the active display.
These are supported by omapdss so that we add all the possible display
devices at probe, but the displays are inactive until somebody enables
one. At this point the panel driver starts using the DSS, thus reserving
the physcal resource and excluding the other panels.
This is problematic:
- Panel drivers can't allocate their resources properly at probe(),
because the resources can be shared with other panels. Thus they can
be only reserved at enable time.
- Managing this in omapdss is confusing. It's not natural to have
child devices, which may not even exist (for example, a daughterboard
that is not connected).
Only some boards have multiple displays per output, and of those, only
very few have possibility of switching the display during runtime.
Because of the above points:
- We don't want to make omapdss and all the panel drivers more complex
just because some boards have complex setups.
- Only few boards support runtime switching, and afaik even then it's
not required. So we don't need to support runtime switching.
Thus we'll change to a model where we will have only one display device
per output and this cannot be (currently) changed at runtime. We'll
still have the possibility to select the display from multiple options
during boot with the default display option.
This patch accomplishes the above by changing how the output drivers
register the display device. Instead of registering all the devices
given from the board file, we'll only register one. If the default
display option is set, the output driver selects that display from its
displays. If the default display is not set, or the default display is
not one of the output's displays, the output driver selects the first
display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We used to have all the displays of the board in one list, and we made a
"displayX" directory in the sysfs, where X was the index of the display
in the list.
This doesn't work anymore with device tree, as there's no single list to
get the number from, and it doesn't work very well even with non-DT as
we need to do some tricks to get the index nowadays.
This patch changes omap_dss_register_device() so that it doesn't take
disp_num as a parameter anymore, but uses a private increasing counter
for the display number.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
set_timings function of DSS's output drivers are not consistent. Some of
them disable the output, set the timings, and re-enable the output. Some
set the timings on the fly, while the output is enabled. And some just
store the given timings, so that they will be taken into use next time
the output is enabled.
We require the DISPC output to be disabled when changing the timings,
and so we can change all the output drivers' set_timings to just store
the given timings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI driver requires vdda_hdmi_dac power for operation, but does not
enable it. This has worked because the regulator has been always
enabled.
But this may not always be the case, as I encountered when implementing
HDMI device tree support.
This patch changes the HDMI driver to use the vdda_hdmi_dac.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
TPD12S015A spec says to wait 300us after setting CT_CP_HPD gpio for the
5V power output to reach 90% of the voltage. This patch adds the delay
to the driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently manage HDMI GPIOs in the board files via
platform_enable/disable calls. This won't work with device tree, and in
any case the correct place to manage the GPIOs is in the HDMI driver.
This patch moves the handling of the GPIOs to the HDMI driver. The GPIO
handling is moved to the common hdmi.c file, and this probably needs to
be revisited when adding OMAP5 HDMI support to see if the GPIO handling
needs to be moved to IP specific files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
