This patch reverts 19a5f5e2ef (f2fs: drop any block plugging),
and adds blk_plug in write paths additionally.
The main reason is that blk_start_plug can be used to wake up from low-power
mode before submitting further bios.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In 1TB storage, we need to admit 22841 prefree segments, which can consume
too much segments.
This patch sets 8GB in max. prefree segments in that case.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
With below test steps, f2fs will issue redundant discard when doing fstrim,
the reason is that we issue discards for both prefree segments and
consecutive freed region user wants to trim, part regions they covered are
overlapped, here, we change to do not to issue any discards for prefree
segments in trimmed range.
1. mount -t f2fs -o discard /dev/zram0 /mnt/f2fs
2. fstrim -o 0 -l 3221225472 -m 2097152 -v /mnt/f2fs/
3. dd if=/dev/zero of=/mnt/f2fs/a bs=2M count=1
4. dd if=/dev/zero of=/mnt/f2fs/b bs=1M count=1
5. sync
6. rm /mnt/f2fs/a /mnt/f2fs/b
7. fstrim -o 0 -l 3221225472 -m 2097152 -v /mnt/f2fs/
Before:
<...>-5428 [001] ...1 9511.052125: f2fs_issue_discard: dev = (251,0), blkstart = 0x2200, blklen = 0x200
<...>-5428 [001] ...1 9511.052787: f2fs_issue_discard: dev = (251,0), blkstart = 0x2200, blklen = 0x300
After:
<...>-6764 [000] ...1 9720.382504: f2fs_issue_discard: dev = (251,0), blkstart = 0x2200, blklen = 0x300
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch skip discard block range smaller than trim_minlen,
and can not be merged by neighbour
Signed-off-by: Yunlei He <heyunlei@huawei.com>
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The readahead nat pages are more likely to be reclaimed quickly, so it'd better
to gather more free nids in advance.
And, let's keep some free nids as much as possible.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This mount option is to enable original log-structured filesystem forcefully.
So, there should be no random writes for main area.
Especially, this supports host-managed SMR device.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In f2fs, we don't need to keep block plugging for NODE and DATA writes, since
we already merged bios as much as possible.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
There is a data race between allocate_data_block() and f2fs_sbumit_page_mbio(),
which incur unnecessary reversed bio submission.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Separate the op from the rq_flag_bits and have f2fs
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
If flush commands do not incur any congestion, we don't need to throw that to
dispatching queue which causes unnecessary latency.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Commit 28bc106b23 ("f2fs: support revoking atomic written pages")
forgot to clear page private flag correctly, fix it.
Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The atomic/volatile operation should be done in pair of start and commit
ioctl.
For example, if a killed process remains open-ended atomic operation, we should
drop its flag as well as its atomic data. Otherwise, if sqlite initiates another
operation which doesn't require atomic writes, it will lose every data, since
f2fs still treats with them as atomic writes; nobody will trigger its commit.
Reported-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new help f2fs_update_data_blkaddr to clean up redundant codes.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
For now, flow of GCing an encrypted data page:
1) try to grab meta page in meta inode's mapping with index of old block
address of that data page
2) load data of ciphertext into meta page
3) allocate new block address
4) write the meta page into new block address
5) update block address pointer in direct node page.
Other reader/writer will use f2fs_wait_on_encrypted_page_writeback to
check and wait on GCed encrypted data cached in meta page writebacked
in order to avoid inconsistence among data page cache, meta page cache
and data on-disk when updating.
However, we will use new block address updated in step 5) as an index to
lookup meta page in inner bio buffer. That would be wrong, and we will
never find the GCing meta page, since we use the old block address as
index of that page in step 1).
This patch fixes the issue by adjust the order of step 1) and step 3),
and in step 1) grab page with index generated in step 3).
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In curseg cache, f2fs caches two different parts:
- datas of current summay block, i.e. summary entries, footer info.
- journal info, i.e. sparse nat/sit entries or io stat info.
With this approach, 1) it may cause higher lock contention when we access
or update both of the parts of cache since we use the same mutex lock
curseg_mutex to protect the cache. 2) current summary block with last
journal info will be writebacked into device as a normal summary block
when flushing, however, we treat journal info as valid one only in current
summary, so most normal summary blocks contain junk journal data, it wastes
remaining space of summary block.
So, in order to fix above issues, we split curseg cache into two parts:
a) current summary block, protected by original mutex lock curseg_mutex
b) journal cache, protected by newly introduced r/w semaphore journal_rwsem
When loading curseg cache during ->mount, we store summary info and
journal info into different caches; When doing checkpoint, we combine
datas of two cache into current summary block for persisting.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Try to use block plug in more place as below to let process cache bios
as much as possbile, in order to reduce lock overhead of queue in IO
scheduler.
1) sync_meta_pages
2) ra_meta_pages
3) f2fs_balance_fs_bg
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
f2fs support atomic write with following semantics:
1. open db file
2. ioctl start atomic write
3. (write db file) * n
4. ioctl commit atomic write
5. close db file
With this flow we can avoid file becoming corrupted when abnormal power
cut, because we hold data of transaction in referenced pages linked in
inmem_pages list of inode, but without setting them dirty, so these data
won't be persisted unless we commit them in step 4.
But we should still hold journal db file in memory by using volatile
write, because our semantics of 'atomic write support' is incomplete, in
step 4, we could fail to submit all dirty data of transaction, once
partial dirty data was committed in storage, then after a checkpoint &
abnormal power-cut, db file will be corrupted forever.
So this patch tries to improve atomic write flow by adding a revoking flow,
once inner error occurs in committing, this gives another chance to try to
revoke these partial submitted data of current transaction, it makes
committing operation more like aotmical one.
If we're not lucky, once revoking operation was failed, EAGAIN will be
reported to user for suggesting doing the recovery with held journal file,
or retrying current transaction again.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Split drop_inmem_pages from commit_inmem_pages for code readability,
and prepare for the following modification.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
f2fs use single bio buffer per type data (META/NODE/DATA) for caching
writes locating in continuous block address as many as possible, after
submitting, these writes may be still cached in bio buffer, so we have
to flush cached writes in bio buffer by calling f2fs_submit_merged_bio.
Unfortunately, in the scenario of high concurrency, bio buffer could be
flushed by someone else before we submit it as below reasons:
a) there is no space in bio buffer.
b) add a request of different type (SYNC, ASYNC).
c) add a discontinuous block address.
For this condition, f2fs_submit_merged_bio will be devastating, because
it could break the following merging of writes in bio buffer, split one
big bio into two smaller one.
This patch introduces f2fs_submit_merged_bio_cond which can do a
conditional submitting with bio buffer, before submitting it will judge
whether:
- page in DATA type bio buffer is matching with specified page;
- page in DATA type bio buffer is belong to specified inode;
- page in NODE type bio buffer is belong to specified inode;
If there is no eligible page in bio buffer, we will skip submitting step,
result in gaining more chance to merge consecutive block IOs in bio cache.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In write_begin, if storage supports stable_page, we don't need to wait for
writeback to update its contents.
This patch introduces to use wait_for_stable_page instead of
wait_on_page_writeback.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
get_new_segment starts from current segment position, tries to search a
free segment among its right neighbors locate in same section.
But previously our search area was set as [current segment, max segment],
which means we have to search to more bits in free_segmap bitmap for some
worse cases. So here we correct the search area to [current segment, last
segment in section] to avoid unnecessary searching.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When testing f2fs with xfstest, generic/251 is stuck for long time,
the case uses below serials to obtain fresh released space in device,
in order to prepare for following fstrim test.
1. rm -rf /mnt/dir
2. mkdir /mnt/dir/
3. cp -axT `pwd`/ /mnt/dir/
4. goto 1
During preparing step, all nat entries will be cached in nat cache,
most of them are dirty entries with invalid blkaddr, which means
nodes related to these entries have been truncated, and they could
be reused after the dirty entries been checkpointed.
However, there was no checkpoint been triggered, so nid allocators
(e.g. mkdir, creat) will run into long journey of iterating all NAT
pages, looking for free nids in alloc_nid->build_free_nids.
Here, in f2fs_balance_fs_bg we give another chance to do checkpoint
to flush nat entries for reusing them in free nid cache when dirty
entry count exceeds 10% of max count.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Operations in is_merged_page is related to inner bio cache, move it to
data.c.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds last time that user requested filesystem operations.
This information is used to detect whether system is idle or not later.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
do_checkpoint and write_checkpoint can fail due to reasons like triggering
in a readonly fs or encountering IO error of storage device.
So it's better to report such error info to user, let user be aware of
failure of doing checkpoint.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Previously, when finishing a checkpoint, we have persisted all fs meta
info including meta inode, node inode, dentry page of directory inode, so,
after a sudden power cut, f2fs can recover from last checkpoint with full
directory structure.
But during checkpoint, we didn't flush dirty pages of regular and symlink
inode, so such dirty datas still in memory will be lost in that moment of
power off.
In order to reduce the chance of lost data, this patch enables
f2fs_balance_fs_bg with the ability of data flushing. It will try to flush
user data before starting a checkpoint. So user's data written after last
checkpoint which may not be fsynced could be saved.
When we mount with data_flush option, after every period of cp_interval
(could be configured in sysfs: /sys/fs/f2fs/device/cp_interval) seconds
user data could be flushed into device once f2fs_balance_fs_bg was called
in kworker thread or gc thread.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch enhances the existing bit operation when f2fs allocates SSR
blocks.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Clean up codes in lookup_journal_in_cursum() with __has_cursum_space().
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
We should clear uptodate flag for all pages atomic written when we drop
them, otherwise before these cached pages were reclaimed or invalidated
eventually, we will see invalid data when hitting them again.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
1. Skip __reverse_ulong if the bitmap is empty.
2. Reduce branches and codes.
According to my test, the performance of this new version is 5% higher on
an empty bitmap of 64bytes, and remains about the same in the worst scenario.
Signed-off-by: Fan li <fanofcode.li@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Atomic write page can be GCed, after committing this kind of page, we should
clear the GCed flag for it.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
different competitors
Since we use different page cache (normally inode's page cache for R/W
and meta inode's page cache for GC) to cache the same physical block
which is belong to an encrypted inode. Writeback of these two page
cache should be exclusive, but now we didn't handle writeback state
well, so there may be potential racing problem:
a)
kworker: f2fs_gc:
- f2fs_write_data_pages
- f2fs_write_data_page
- do_write_data_page
- write_data_page
- f2fs_submit_page_mbio
(page#1 in inode's page cache was queued
in f2fs bio cache, and be ready to write
to new blkaddr)
- gc_data_segment
- move_encrypted_block
- pagecache_get_page
(page#2 in meta inode's page cache
was cached with the invalid datas
of physical block located in new
blkaddr)
- f2fs_submit_page_mbio
(page#1 was submitted, later, page#2
with invalid data will be submitted)
b)
f2fs_gc:
- gc_data_segment
- move_encrypted_block
- f2fs_submit_page_mbio
(page#1 in meta inode's page cache was
queued in f2fs bio cache, and be ready
to write to new blkaddr)
user thread:
- f2fs_write_begin
- f2fs_submit_page_bio
(we submit the request to block layer
to update page#2 in inode's page cache
with physical block located in new
blkaddr, so here we may read gabbage
data from new blkaddr since GC hasn't
writebacked the page#1 yet)
This patch fixes above potential racing problem for encrypted inode.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Now, we use ra_meta_pages to reads continuous physical blocks as much as
possible to improve performance of following reads. However, ra_meta_pages
uses a synchronous readahead approach by submitting bio with READ, as READ
is with high priority, it can not be used in the case of preloading blocks,
and it's not sure when these RAed pages will be used.
This patch supports asynchronous readahead in ra_meta_pages by tagging bio
with READA flag in order to allow preloading.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In recovery or checkpoint flow, we grab pages temperarily in meta inode's
mapping for caching temperary data, actually, datas in these pages were
not meta data of f2fs, but still we tag them with REQ_META flag. However,
lower device like eMMC may do some optimization for data of such type.
So in order to avoid wrong optimization, we'd better remove such flag
for temperary non-meta pages.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The f2fs_collapse_range and f2fs_insert_range changes the block addresses
directly. But that can cause uncovered SSA updates.
In that case, we need to give up to change the block addresses and do buffered
writes to keep filesystem consistency.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch introduces a periodic checkpoint feature.
Note that, this is not enforcing to conduct checkpoints very strictly in terms
of trigger timing, instead just hope to help user experiences.
The default value is 60 seconds.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch drops in batches gc triggered through ioctl, since user
can easily control the gc by designing the loop around the ->ioctl.
We support synchronous gc by forcing using FG_GC in f2fs_gc, so with
it, user can make sure that in this round all blocks gced were
persistent in the device until ioctl returned.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
__GFP_NOFAIL can avoid retrying the whole path of kmem_cache_alloc and
bio_alloc.
And, it also fixes the use cases of GFP_ATOMIC correctly.
Suggested-by: Chao Yu <chao2.yu@samsung.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
As the below comment of bio_alloc_bioset, f2fs can allocate multiple bios at the
same time. So, we can't guarantee that bio is allocated all the time.
"
* When @bs is not NULL, if %__GFP_WAIT is set then bio_alloc will always be
* able to allocate a bio. This is due to the mempool guarantees. To make this
* work, callers must never allocate more than 1 bio at a time from this pool.
* Callers that need to allocate more than 1 bio must always submit the
* previously allocated bio for IO before attempting to allocate a new one.
* Failure to do so can cause deadlocks under memory pressure.
"
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch introduces __count_free_nids/try_to_free_nids and registers
them in slab shrinker for shrinking under memory pressure.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If there is not enough free segment, we should not assign a new segment
explicitly. Otherwise, we can run out of free segment.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Previously, we use radix tree to index all registered page entries for
atomic file, but now we only use radix tree to see whether current page
is indexed or not, since the other user of radix tree is gone in commit
042b7816aa ("f2fs: remove unnecessary call to invalidate inmemory pages").
So in this patch, we try to use one more efficient way:
Introducing a macro ATOMIC_WRITTEN_PAGE, and setting it as page private
value to indicate page indexing status. By using this way, we can save
memory and lookup time.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
To avoid meeting garbage data in next free node block at the end of warm
node chain when doing recovery, we will try to zero out that invalid block.
If the device is not support discard, our way for zeroing out block is:
grabbing a temporary zeroed page in meta inode, then, issue write request
with this page.
But, we forget to release that temporary page, so our memory usage will
increase without gaining any hit ratio benefit, so it's better to free it
for saving memory.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds to handle error cases in commit_inmem_pages.
If an error occurs, it stops to write the pages and return the error right
away.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Now, we add all the candidates for trim commands and then finally issue
discard commands.
So, we should count the trimmed size in back-end.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch clean up codes through:
1.rename f2fs_replace_block to __f2fs_replace_block().
2.introduce new f2fs_replace_block() to include __f2fs_replace_block()
and some common related codes around __f2fs_replace_block().
Then, newly introduced function f2fs_replace_block can be used by
following patch.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Add a help function update_meta_page() to update meta page with specified
buffer.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Now page cache of meta inode is used by garbage collection for encrypted page,
it may contain random data, so we should zero it before issuing discard.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch integrates the below patch into f2fs.
"ext4 crypto: shrink size of the ext4_crypto_ctx structure
Some fields are only used when the crypto_ctx is being used on the
read path, some are only used on the write path, and some are only
used when the structure is on free list. Optimize memory use by using
a union."
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The return was not indented far enough so it looked like it was supposed
to go with the other if statement.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds encryption support in read and write paths.
Note that, in f2fs, we need to consider cleaning operation.
In cleaning procedure, we must avoid encrypting and decrypting written blocks.
So, this patch implements move_encrypted_block().
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Introduce a generic function replace_block base on recover_data_page,
and export it. So with it we can operate file's meta data which is in
CP/SSA area when we invoke fallocate with FALLOC_FL_COLLAPSE_RANGE
flag.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch determines to issue discard commands by comparing given minlen and
the length of produced final candidates.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds a bitmap for discard issues from f2fs_trim_fs.
There-in rule is to issue discard commands only for invalidated blocks
after mount.
Once mount is done, f2fs_trim_fs trims out whole invalid area.
After ehn, it will not issue and discrads redundantly.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds f2fs_sb_info and page pointers in f2fs_io_info structure.
With this change, we can reduce a lot of parameters for IO functions.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In the following call stack, f2fs changes the bitmap for dirty segments and # of
dirty sentries without grabbing sit_i->sentry_lock.
This can result in mismatch on bitmap and # of dirty sentries, since if there
are some direct_io operations.
In allocate_data_block,
- __allocate_new_segments
- mutex_lock(&curseg->curseg_mutex);
- s_ops->allocate_segment
- new_curseg/change_curseg
- reset_curseg
- __set_sit_entry_type
- __mark_sit_entry_dirty
- set_bit(dirty_sentries_bitmap)
- dirty_sentries++;
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Now in f2fs, we share functions and structures for batch mode and real-time mode
discard. For real-time mode discard, in shared function add_discard_addrs, we
will use uninitialized trim_minlen in struct cp_control to compare with length
of contiguous free blocks to decide whether skipping discard fragmented freespace
or not, this makes us ignore small discard sometimes. Fix it.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Reviewed-by : Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Don't need to collect dirty sit entries and flush sit journal to sit
entries when there's no dirty sit entries. This patch check dirty_sentries
earlier just like flush_nat_entries.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch enables rb-tree based extent cache in f2fs.
When we mount with "-o extent_cache", f2fs will try to add recently accessed
page-block mappings into rb-tree based extent cache as much as possible, instead
of original one extent info cache.
By this way, f2fs can support more effective cache between dnode page cache and
disk. It will supply high hit ratio in the cache with fewer memory when dnode
page cache are reclaimed in environment of low memory.
Storage: Sandisk sd card 64g
1.append write file (offset: 0, size: 128M);
2.override write file (offset: 2M, size: 1M);
3.override write file (offset: 4M, size: 1M);
...
4.override write file (offset: 48M, size: 1M);
...
5.override write file (offset: 112M, size: 1M);
6.sync
7.echo 3 > /proc/sys/vm/drop_caches
8.read file (size:128M, unit: 4k, count: 32768)
(time dd if=/mnt/f2fs/128m bs=4k count=32768)
Extent Hit Ratio:
before patched
Hit Ratio 121 / 1071 1071 / 1071
Performance:
before patched
real 0m37.051s 0m35.556s
user 0m0.040s 0m0.026s
sys 0m2.990s 0m2.251s
Memory Cost:
before patched
Tree Count: 0 1 (size: 24 bytes)
Node Count: 0 45 (size: 1440 bytes)
v3:
o retest and given more details of test result.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
rwlock can provide better concurrency when there are much more readers than
writers because readers can hold the rwlock simultaneously.
But now, for segmap_lock rwlock in struct free_segmap_info, there is only one
reader 'mount' from below call path:
->f2fs_fill_super
->build_segment_manager
->build_dirty_segmap
->init_dirty_segmap
->find_next_inuse
read_lock
...
read_unlock
Now that our concurrency can not be improved since there is no other reader for
this lock, we do not need to use rwlock_t type for segmap_lock, let's replace it
with spinlock_t type.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds two macros for transition between byte and block offsets.
Currently, f2fs only supports 4KB blocks, so use the default size for now.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch introduces a batched trimming feature, which submits split discard
commands.
This is to avoid long latency due to huge trim commands.
If fstrim was triggered ranging from 0 to the end of device, we should lock
all the checkpoint-related mutexes, resulting in very long latency.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds FASTBOOT flag into checkpoint as follows.
- CP_UMOUNT_FLAG is set when system is umounted.
- CP_FASTBOOT_FLAG is set when intermediate checkpoint having node summaries
was done.
So, if you get CP_UMOUNT_FLAG from checkpoint, the system was umounted cleanly.
Instead, if there was sudden-power-off, you can get CP_FASTBOOT_FLAG or nothing.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch aligns the start block address of a file for direct io to the f2fs's
section size.
Some flash devices manage an over 4KB-sized page as a write unit, and if the
direct_io'ed data are written but not aligned to that unit, the performance can
be degraded due to the partial page copies.
Thus, since f2fs has a section that is well aligned to FTL units, we can align
the block address to the section size so that f2fs avoids this misalignment.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds block count by in-place-update in stat.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch cleans up parameters on IO paths.
The key idea is to use f2fs_io_info adding a parameter, block address, and then
use this structure as parameters.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Let's add readahead code for reading contiguous compact/normal summary blocks
in checkpoint, then we will gain better performance in mount procedure.
Changes from v1
o remove inappropriate 'unlikely' in npages_for_summary_flush.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Now we use inmemory pages for atomic write only and provide abort procedure,
we don't need to truncate them explicitly.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The ckpt_valid_map and cur_valid_map are synced by seg_info_to_raw_sit.
In the case of small discards, the candidates are selected before sync,
while fitrim selects candidates after sync.
So, for small discards, we need to add candidates only just being obsoleted.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds two new ioctls to release inmemory pages grabbed by atomic
writes.
o f2fs_ioc_abort_volatile_write
- If transaction was failed, all the grabbed pages and data should be written.
o f2fs_ioc_release_volatile_write
- This is to enhance the performance of PERSIST mode in sqlite.
In order to avoid huge memory consumption which causes OOM, this patch changes
volatile writes to use normal dirty pages, instead blocked flushing to the disk
as long as system does not suffer from memory pressure.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The inmemory pages should be handled by invalidate_page since it needs to be
released int the truncation path.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch revists retrial paths in f2fs.
The basic idea is to use cond_resched instead of retrying from the very early
stage.
Suggested-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In f2fs_evict_inode,
commit_inmemory_pages
f2fs_gc
f2fs_iget
iget_locked
-> wait for inode free
Here, if the inode is same as the one to be evicted, f2fs should wait forever.
Actually, we should not call f2fs_balance_fs during f2fs_evict_inode to avoid
this.
But, the commit_inmem_pages calls f2fs_balance_fs by default, even if
f2fs_evict_inode wants to free inmemory pages only.
Hence, this patch adds to trigger f2fs_balance_fs only when there is something
to write.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
It used nat_entry_set when create slab for sit_entry_set.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds to control the memory footprint used by ino entries.
This will conduct best effort, not strictly.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If there is a chance to make a huge sized discard command, we don't need
to split it out, since each blkdev_issue_discard should wait one at a
time.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Rename f2fs_set/clear_bit to f2fs_test_and_set/clear_bit, which mean
set/clear bit and return the old value, for better readability.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If user specifies too low end sector for trimming, f2fs_trim_fs() will
use uninitialized value as a number of trimmed blocks and returns it to
userspace. Initialize number of trimmed blocks early to avoid the
problem.
Coverity-id: 1248809
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch introduces a very limited functionality for atomic write support.
In order to support atomic write, this patch adds two ioctls:
o F2FS_IOC_START_ATOMIC_WRITE
o F2FS_IOC_COMMIT_ATOMIC_WRITE
The database engine should be aware of the following sequence.
1. open
-> ioctl(F2FS_IOC_START_ATOMIC_WRITE);
2. writes
: all the written data will be treated as atomic pages.
3. commit
-> ioctl(F2FS_IOC_COMMIT_ATOMIC_WRITE);
: this flushes all the data blocks to the disk, which will be shown all or
nothing by f2fs recovery procedure.
4. repeat to #2.
The IO pattens should be:
,- START_ATOMIC_WRITE ,- COMMIT_ATOMIC_WRITE
CP | D D D D D D | FSYNC | D D D D | FSYNC ...
`- COMMIT_ATOMIC_WRITE
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch introduces FITRIM in f2fs_ioctl.
In this case, f2fs will issue small discards and prefree discards as many as
possible for the given area.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch changes the ipu_policy setting to use any combination of orthogonal policies.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Block size in f2fs is 4096 bytes, so theoretically, f2fs can support 4096 bytes
sector device at maximum. But now f2fs only support 512 bytes size sector, so
block device such as zRAM which uses page cache as its block storage space will
not be mounted successfully as mismatch between sector size of zRAM and sector
size of f2fs supported.
In this patch we support large sector size in f2fs, so block device with sector
size of 512/1024/2048/4096 bytes can be supported in f2fs.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If user wrote F2FS_IPU_FSYNC:4 in /sys/fs/f2fs/ipu_policy, f2fs_sync_file
only starts to try in-place-updates.
And, if the number of dirty pages is over /sys/fs/f2fs/min_fsync_blocks, it
keeps out-of-order manner. Otherwise, it triggers in-place-updates.
This may be used by storage showing very high random write performance.
For example, it can be used when,
Seq. writes (Data) + wait + Seq. writes (Node)
is pretty much slower than,
Rand. writes (Data)
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
We use flush cmd control to collect many flush cmds, and flush them
together. In this case, we use two list to manage the flush cmds
(collect and dispatch), and one spin lock is used to protect this.
In fact, the lock-less list(llist) is very suitable to this case,
and we use simplify this routine.
-
v2:
-use llist_for_each_entry_safe to fix possible use-after-free issue.
-remove the unused field from struct flush_cmd.
Thanks for Yu's suggestion.
-
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In commit aec71382c6 ("f2fs: refactor flush_nat_entries codes for reducing NAT
writes"), we descripte the issue as below:
"Although building NAT journal in cursum reduce the read/write work for NAT
block, but previous design leave us lower performance when write checkpoint
frequently for these cases:
1. if journal in cursum has already full, it's a bit of waste that we flush all
nat entries to page for persistence, but not to cache any entries.
2. if journal in cursum is not full, we fill nat entries to journal util
journal is full, then flush the left dirty entries to disk without merge
journaled entries, so these journaled entries may be flushed to disk at next
checkpoint but lost chance to flushed last time."
Actually, we have the same problem in using SIT journal area.
In this patch, firstly we will update sit journal with dirty entries as many as
possible. Secondly if there is no space in sit journal, we will remove all
entries in journal and walk through the whole dirty entry bitmap of sit,
accounting dirty sit entries located in same SIT block to sit entry set. All
entry sets are linked to list sit_entry_set in sm_info, sorted ascending order
by count of entries in set. Later we flush entries in set which have fewest
entries into journal as many as we can, and then flush dense set with merged
entries to disk.
In this way we can use sit journal area more effectively, also we will reduce
SIT update, result in gaining in performance and saving lifetime of flash
device.
In my testing environment, it shows this patch can help to reduce SIT block
update obviously.
virtual machine + hard disk:
fsstress -p 20 -n 400 -l 5
sit page num cp count sit pages/cp
based 2006.50 1349.75 1.486
patched 1566.25 1463.25 1.070
Our latency of merging op is small when handling a great number of dirty SIT
entries in flush_sit_entries:
latency(ns) dirty sit count
36038 2151
49168 2123
37174 2232
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
sit_i in macro SIT_BLOCK_OFFSET/START_SEGNO is not used, remove it.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch replaces BUG cases with f2fs_bug_on to remain fsck.f2fs information.
And it implements some void functions to initiate fsck.f2fs too.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
I think we need to let the dirty node pages remain in the page cache instead
of rewriting them in their places.
So, after done with successful recovery, write_checkpoint will flush all of them
through the normal write path.
Through this, we can avoid potential error cases in terms of block allocation.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Fix typo and some grammatical errors.
The words "filesystem" and "readahead" are being used without the space treewide.
Signed-off-by: Park Ju Hyung <qkrwngud825@gmail.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch uses for_each_set_bit to simplify some codes in f2fs.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
There are redundant lines in allocate_data_block.
In this function, we call refresh_sit_entry with old seg and old curseg.
After that, we call locate_dirty_segment with old curseg.
But, the new address is always allocated from old curseg and
we call locate_dirty_segment with old curseg in refresh_sit_entry.
So, we do not need to call locate_dirty_segment with old curseg again.
We've discussed like below:
Jaegeuk said:
"When considering SSR, we need to take care of the following scenario.
- old segno : X
- new address : Z
- old curseg : Y
This means, a new block is supposed to be written to Z from X.
And Z is newly allocated in the same path from Y.
In that case, we should trigger locate_dirty_segment for Y, since
it was a current_segment and can be dirty owing to SSR.
But that was not included in the dirty list."
Changman said:
"We already choosed old curseg(Y) and then we allocate new address(Z) from old
curseg(Y). After that we call refresh_sit_entry(old address, new address).
In the funcation, we call locate_dirty_segment with old seg and old curseg.
So calling locate_dirty_segment after refresh_sit_entry again is redundant."
Jaegeuk said:
"Right. The new address is always allocated from old_curseg."
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Dongho Sim <dh.sim@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds a mount option, nobarrier, in f2fs.
The assumption in here is that file system keeps the IO ordering, but
doesn't care about cache flushes inside the storages.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In this patch we use below inner macro and function to clean up codes.
1. ADDRS_PER_PAGE
2. SM_I
3. f2fs_readonly
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75861
Denis 2014-05-10 11:28:59 UTC reported:
"F2FS-fs (mmcblk0p28): mounting..
Unable to handle kernel NULL pointer dereference at virtual address 00000018
...
[<c0a2f678>] (_raw_spin_lock+0x3c/0x70) from [<c03a0330>] (issue_flush_thread+0x50/0x17c)
[<c03a0330>] (issue_flush_thread+0x50/0x17c) from [<c01b4064>] (kthread+0x98/0xa4)
[<c01b4064>] (kthread+0x98/0xa4) from [<c0108060>] (kernel_thread_exit+0x0/0x8)"
This patch assign cmd_control_info in sm_info before issue_flush_thread is being
created, so this make sure that issue flush thread will have no chance to access
invalid info in fcc.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If we use slab memory in f2fs_issue_flush(), we will face memory pressure and
latency time caused by racing of kmem_cache_{alloc,free}.
Let's alloc memory in stack instead of slab.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce help function {create,destroy}_flush_cmd_control to clean up
the create/destory flush merge operation.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Split the flush_merge fields from sm_i, and use the new struct flush_cmd_control
to wrap it, so that we can igonre these fileds if flush_merge is disable, and
it alse can the structs more neat.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add the *remount* handle of flush_merge option, so that the users
can enable flush_merge in the runtime, such as the underlying device
handles the cache_flush command relatively slowly.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The f2fs always scans the next chain of direct node blocks.
But some garbage blocks are able to be remained due to no discard support or
SSR triggers.
This occasionally wreaks recovering wrong inodes that were used or BUG_ONs
due to reallocating node ids as follows.
When mount this f2fs image:
http://linuxtesting.org/downloads/f2fs_fault_image.zip
BUG_ON is triggered in f2fs driver (messages below are generated on
kernel 3.13.2; for other kernels output is similar):
kernel BUG at fs/f2fs/node.c:215!
Call Trace:
[<ffffffffa032ebad>] recover_inode_page+0x1fd/0x3e0 [f2fs]
[<ffffffff811446e7>] ? __lock_page+0x67/0x70
[<ffffffff81089990>] ? autoremove_wake_function+0x50/0x50
[<ffffffffa0337788>] recover_fsync_data+0x1398/0x15d0 [f2fs]
[<ffffffff812b9e5c>] ? selinux_d_instantiate+0x1c/0x20
[<ffffffff811cb20b>] ? d_instantiate+0x5b/0x80
[<ffffffffa0321044>] f2fs_fill_super+0xb04/0xbf0 [f2fs]
[<ffffffff811b861e>] ? mount_bdev+0x7e/0x210
[<ffffffff811b8769>] mount_bdev+0x1c9/0x210
[<ffffffffa0320540>] ? validate_superblock+0x210/0x210 [f2fs]
[<ffffffffa031cf8d>] f2fs_mount+0x1d/0x30 [f2fs]
[<ffffffff811b9497>] mount_fs+0x47/0x1c0
[<ffffffff81166e00>] ? __alloc_percpu+0x10/0x20
[<ffffffff811d4032>] vfs_kern_mount+0x72/0x110
[<ffffffff811d6763>] do_mount+0x493/0x910
[<ffffffff811615cb>] ? strndup_user+0x5b/0x80
[<ffffffff811d6c70>] SyS_mount+0x90/0xe0
[<ffffffff8166f8d9>] system_call_fastpath+0x16/0x1b
Found by Linux File System Verification project (linuxtesting.org).
Reported-by: Andrey Tsyvarev <tsyvarev@ispras.ru>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Enable flush_merge only in f2fs is not read-only, so does the mount
option show.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Some storage devices show relatively high latencies to complete cache_flush
commands, even though their normal IO speed is prettry much high. In such
the case, it needs to merge cache_flush commands as much as possible to avoid
issuing them redundantly.
So, this patch introduces a mount option, "-o flush_merge", to mitigate such
the overhead.
If this option is enabled by user, F2FS merges the cache_flush commands and then
issues just one cache_flush on behalf of them. Once the single command is
finished, F2FS sends a completion signal to all the pending threads.
Note that, this option can be used under a workload consisting of very intensive
concurrent fsync calls, while the storage handles cache_flush commands slowly.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
In the f2fs_wait_on_page_writeback, io->bio should be covered by io_rwsem.
Otherwise, the bio pointer can become a dangling pointer due to data races.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch use list_for_each_entry{_safe} instead of list_for_each{_safe} for
simplfying code.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch introduce is_merged_page() to check whether current page is merged
in f2fs bio cache. When page is not in cache, we can avoid submitting bio cache,
resulting in having more chance to merge pages.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
It is more reasonable to determine the reclaiming rate of prefree segments
according to the volume size, which is set to 5% by default.
For example, if the volume is 128GB, the prefree segments are reclaimed
when the number reaches to 6.4GB.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
We should return error number of read_normal_summaries instead of -EINVAL when
read_normal_summaries failed.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, we ra_sum_pages to pre-read contiguous pages as more
as possible, and if we fail to alloc more pages, an ENOMEM error
will be reported upstream, even though we have alloced some pages
yet. In fact, we can use the available pages to do the job partly,
and continue the rest in the following circle. Only reporting ENOMEM
upstream if we really can not alloc any available page.
And another fix is ignoring dealing with the following pages if an
EIO occurs when reading page from page_list.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
[Jaegeuk Kim: modify the flow for better neat code]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch help us to cleanup the readahead code by merging ra_{sit,nat}_pages
function into ra_meta_pages.
Additionally the new function is used to readahead cp block in
recover_orphan_inodes.
Change log from v1:
o fix a deadloop bug pointed by Jaegeuk Kim.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Introduce help function META_MAPPING() to get the cache meta blocks'
address space.
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Fixed a variety of trivial checkpatch warnings. The only delta should
be some minor formatting on log strings that were split / too long.
Signed-off-by: Chris Fries <cfries@motorola.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
"boo sync" parameter is never referenced in f2fs_wait_on_page_writeback.
We should remove this parameter.
Signed-off-by: Yuan Zhong <yuan.mark.zhong@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When considering a bunch of data writes with very frequent fsync calls, we
are able to think the following performance regression.
N: Node IO, D: Data IO, IO scheduler: cfq
Issue pending IOs
D1 D2 D3 D4
D1 D2 D3 D4 N1
D2 D3 D4 N1 N2
N1 D3 D4 N2 D1
--> N1 can be selected by cfq becase of the same priority of N and D.
Then D3 and D4 would be delayed, resuling in performance degradation.
So, when processing the fsync call, it'd better give higher priority to data IOs
than node IOs by assigning WRITE and WRITE_SYNC respectively.
This patch improves the random wirte performance with frequent fsync calls by up
to 10%.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When using the f2fs_io_info in the low level, we still need to merge the
rw and rw_flag, so use the rw to hold all the io flags directly,
and remove the rw_flag field.
ps.It is based on the previous patch:
f2fs: move all the bio initialization into __bio_alloc
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs doesn't support direct IOs with high performance, which throws
every write requests via the buffered write path, resulting in highly
performance degradation due to memory opeations like copy_from_user.
This patch introduces a new direct IO path in which every write requests are
processed by generic blockdev_direct_IO() with enhanced get_block function.
The get_data_block() in f2fs handles:
1. if original data blocks are allocates, then give them to blockdev.
2. otherwise,
a. preallocate requested block addresses
b. do not use extent cache for better performance
c. give the block addresses to blockdev
This policy induces that:
- new allocated data are sequentially written to the disk
- updated data are randomly written to the disk.
- f2fs gives consistency on its file meta, not file data.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch introduces new sysfs entries for users to control the policy of
in-place-updates, namely IPU, in f2fs.
Sometimes f2fs suffers from performance degradation due to its out-of-place
update policy that produces many additional node block writes.
If the storage performance is very dependant on the amount of data writes
instead of IO patterns, we'd better drop this out-of-place update policy.
This patch suggests 5 polcies and their triggering conditions as follows.
[sysfs entry name = ipu_policy]
0: F2FS_IPU_FORCE all the time,
1: F2FS_IPU_SSR if SSR mode is activated,
2: F2FS_IPU_UTIL if FS utilization is over threashold,
3: F2FS_IPU_SSR_UTIL if SSR mode is activated and FS utilization is over
threashold,
4: F2FS_IPU_DISABLE disable IPU. (=default option)
[sysfs entry name = min_ipu_util]
This parameter controls the threshold to trigger in-place-updates.
The number indicates percentage of the filesystem utilization, and used by
F2FS_IPU_UTIL and F2FS_IPU_SSR_UTIL policies.
For more details, see need_inplace_update() in segment.h.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch introduces f2fs_io_info to mitigate the complex parameter list.
struct f2fs_io_info {
enum page_type type; /* contains DATA/NODE/META/META_FLUSH */
int rw; /* contains R/RS/W/WS */
int rw_flag; /* contains REQ_META/REQ_PRIO */
}
1. f2fs_write_data_pages
- DATA
- WRITE_SYNC is set when wbc->WB_SYNC_ALL.
2. sync_node_pages
- NODE
- WRITE_SYNC all the time
3. sync_meta_pages
- META
- WRITE_SYNC all the time
- REQ_META | REQ_PRIO all the time
** f2fs_submit_merged_bio() handles META_FLUSH.
4. ra_nat_pages, ra_sit_pages, ra_sum_pages
- META
- READ_SYNC
Cc: Fan Li <fanofcode.li@samsung.com>
Cc: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously f2fs submits most of write requests using WRITE_SYNC, but f2fs_write_data_pages
submits last write requests by sync_mode flags callers pass.
This causes a performance problem since continuous pages with different sync flags
can't be merged in cfq IO scheduler(thanks yu chao for pointing it out), and synchronous
requests often take more time.
This patch makes the following modifies to DATA writebacks:
1. every page will be written back using the sync mode caller pass.
2. only pages with the same sync mode can be merged in one bio request.
These changes are restricted to DATA pages.Other types of writebacks are modified
To remain synchronous.
In my test with tiotest, f2fs sequence write performance is improved by about 7%-10% ,
and this patch has no obvious impact on other performance tests.
Signed-off-by: Fan Li <fanofcode.li@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch integrates redundant bio operations on read and write IOs.
1. Move bio-related codes to the top of data.c.
2. Replace f2fs_submit_bio with f2fs_submit_merged_bio, which handles read
bios additionally.
3. Introduce __submit_merged_bio to submit the merged bio.
4. Change f2fs_readpage to f2fs_submit_page_bio.
5. Introduce f2fs_submit_page_mbio to integrate previous submit_read_page and
submit_write_page.
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com >
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously f2fs allocates its own bi_private data structure all the time even
though we don't use it. But, can we remove this bi_private allocation?
This patch removes such the additional bi_private allocation.
1. Retrieve f2fs_sb_info from its page->mapping->host->i_sb.
- This removes the usecases of bi_private in end_io.
2. Use bi_private only when we really need it.
- The bi_private is used only when the checkpoint procedure is conducted.
- When conducting the checkpoint, f2fs submits a META_FLUSH bio to wait its bio
completion.
- Since we have no dependancies to remove bi_private now, let's just use
bi_private pointer as the completion pointer.
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch fixes some bit overflows by the shift operations.
Dan Carpenter reported potential bugs on bit overflows as follows.
fs/f2fs/segment.c:910 submit_write_page()
warn: should 'blk_addr << ((sbi)->log_blocksize - 9)' be a 64 bit type?
fs/f2fs/checkpoint.c:429 get_valid_checkpoint()
warn: should '1 << ()' be a 64 bit type?
fs/f2fs/data.c:408 f2fs_readpage()
warn: should 'blk_addr << ((sbi)->log_blocksize - 9)' be a 64 bit type?
fs/f2fs/data.c:457 submit_read_page()
warn: should 'blk_addr << ((sbi)->log_blocksize - 9)' be a 64 bit type?
fs/f2fs/data.c:525 get_data_block_ro()
warn: should 'i << blkbits' be a 64 bit type?
Bug-Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Let's send REQ_META or REQ_PRIO when reading meta area such as NAT/SIT
etc.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch inserts information of bio types in more detail.
So, we can now see REQ_META and REQ_PRIO too.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously we read sit entries page one by one, this method lost the chance
of reading contiguous page together. So we read pages as contiguous as
possible for better mount performance.
change log:
o merge judgements/use 'Continue' or 'Break' instead of 'Goto' as Gu Zheng
suggested.
o add mark_page_accessed() before release page to delay VM reclaiming.
o remove '*order' for simplification of function as Jaegeuk Kim suggested.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
[Jaegeuk Kim: fix a bug on the block address calculation]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a tracepoint for f2fs_submit_read_bio.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
[Jaegeuk Kim: integrate tracepoints of f2fs_submit_read(_write)_bio]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a tracepoint for submit_read_page.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
[Jaegeuk Kim: integrate tracepoints of f2fs_submit_read(_write)_page]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
The f2fs has three bio types, NODE, DATA, and META, and manages some data
structures per each bio types.
The codes are a little bit messy, thus, this patch introduces a bio array
which groups individual data structures as follows.
struct f2fs_bio_info {
struct bio *bio; /* bios to merge */
sector_t last_block_in_bio; /* last block number */
struct mutex io_mutex; /* mutex for bio */
};
struct f2fs_sb_info {
...
struct f2fs_bio_info write_io[NR_PAGE_TYPE]; /* for write bios */
...
};
The code changes from this new data structure are trivial.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch removes an unnecessary semaphore (i.e., sbi->bio_sem).
There is no reason to use the semaphore when f2fs submits read and write IOs.
Instead, let's use a write mutex and cover the sbi->bio[] by the lock.
Change log from v1:
o split write_mutex suggested by Chao Yu
Chao described,
"All DATA/NODE/META bio buffers in superblock is protected by
'sbi->write_mutex', but each bio buffer area is independent, So we
should split write_mutex to three for DATA/NODE/META."
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Change log from v1:
o fix 32bit drops reported by Dan Carpenter
This patch adds f2fs_issue_discard() to clean up blkdev_issue_discard() flows.
Dan carpenter reported:
"block_t is a 32 bit type and sector_t is a 64 bit type. The upper 32
bits of the sector_t are not used because the shift will wrap."
Bug-Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds key functions to activate the small discard feature.
Note that this procedure is conducted during the checkpoint only.
In flush_sit_entries(), when a new dirty sit entry is flushed, f2fs calls
add_discard_addrs() which searches candidates to be discarded.
The candidates should be marked *invalidated* and also previous checkpoint
recognizes it as *valid*.
At the end of a checkpoint procedure, f2fs throws discards based on the
discard entry list.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds a slab cache entry for small discards.
Each entry consists of:
struct discard_entry {
struct list_head list; /* list head */
block_t blkaddr; /* block address to be discarded */
int len; /* # of consecutive blocks of the discard */
};
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
To find a zero bit using the result of OR operation between ckpt_valid_map
and cur_valid_map is more fast than find a zero bit in each bitmap.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
[Jaegeuk Kim: adjust changed function name]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
When f2fs_set_bit is used, in a byte MSB and LSB is reversed,
in that case we can use __find_rev_next_bit or __find_rev_next_zero_bit.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
[Jaegeuk Kim: change the function names]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
o Changes from v1
Use find_next(_zero)_bit suggested by jg.kim
When f2fs issues discard command, if segment is contiguous,
let's issue more large segment to gather adjacent segments.
** blktrace **
179,1 0 5859 42.619023770 971 C D 131072 + 2097152 [0]
179,1 0 33665 108.840475468 971 C D 2228224 + 2494464 [0]
179,1 0 33671 109.131616427 971 C D 14909440 + 344064 [0]
179,1 0 33677 109.137100677 971 C D 15261696 + 4096 [0]
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
use genernal method supported by kernel
o changes from v1
If any waiter exists at end io, wake up it.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
A NULL point should avoid to be used in destroy_segment_manager after allocating
memory fail for f2fs_sm_info.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
npages_for_summary_flush uses (SUMMARY_SIZE + 1) as the size of a f2fs_summary
while its actual size is SUMMARY_SIZE. So the result sometimes is bigger than
actual number by one, which causes checkpoint can't be written into disk
contiguously, and sometimes summary blocks can't be compacted like they should.
Besides, when writing summary blocks into pages, if remain space in a page
isn't big enough for one f2fs_summary, it will be left unused, current code
seems not to take it into account.
Signed-off-by: Fan Li <fanofcode.li@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
If you want to remove unnecessary BUG_ONs, you can just turn off F2FS_CHECK_FS
in your kernel config.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Only one dirty type is set in __locate_dirty_segment and we can know
dirty type of segment. So we don't need to check other dirty types.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, set_page_dirty is called every time after writting one summary info
into compacted summary page,
To avoid redundant set_page_dirty, we only call set_page_dirty before release
page.
Signed-off-by: Yu Chao <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch merges some background jobs into this new function.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, f2fs postpones reclaiming prefree segments into free segments
as much as possible.
However, if user writes and deletes a bunch of data without any sync or fsync
calls, some flash storages can suffer from garbage collections.
So, this patch adds the reclaiming codes to f2fs_write_node_pages and background
GC thread.
If there are a lot of prefree segments, let's do checkpoint so that f2fs
submits discard commands for the prefree regions to the flash storage.
Signed-off-by: Changman Lee <cm224.lee@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Because one dirty seg can only be mapped to one dirty_type. Otherwise, it's a bug.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
[Jaegeuk Kim: modify a comment related to this patch]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Previously, do_checkpoint() will call congestion_wait() for waiting the pages
(previous submitted node/meta/data pages) to be written back.
Because congestion_wait() will set a regular period (e.g. HZ / 50 ) for waiting, and
no additional wake up mechanism was introduced if IO ends up before regular period costed.
Yuan Zhong found there is a situation that after the pages have been written back,
but the checkpoint thread still wait for congestion_wait to exit.
So here we store checkpoint task into f2fs_sb when doing checkpoint, it'll wait for IO completes
if there's IO going on, and in the end IO path, wake up checkpoint task when IO ends up.
Thanks to Yuan Zhong's pre work about this problem.
Reported-by: Yuan Zhong <yuan.mark.zhong@samsung.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch add macro MAX_BIO_BLOCKS to limit value of npages in
f2fs_bio_alloc, it can avoid allocating failure in bio_alloc caused by
npages is larger than BIO_MAX_PAGES.
Signed-off-by: Yu Chao <chao2.yu@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
An error "label at end of compound statement" will occur if CONFIG_F2FS_STAT_FS
disabled.
fs/f2fs/segment.c:556:1: error: label at end of compound statement
So clean up the 'out' label to fix it.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch fixes a deadlock bug that occurs quite often when there are
concurrent write and fsync on a same file.
Following is the simplified call trace when tasks get hung.
fsync thread:
- f2fs_sync_file
...
- f2fs_write_data_pages
...
- update_extent_cache
...
- update_inode
- wait_on_page_writeback
bdi writeback thread
- __writeback_single_inode
- f2fs_write_data_pages
- mutex_lock(sbi->writepages)
The deadlock happens when the fsync thread waits on a inode page that has
been added to the f2fs' cached bio sbi->bio[NODE], and unfortunately,
no one else could be able to submit the cached bio to block layer for
writeback. This is because the fsync thread already hold a sbi->fs_lock and
the sbi->writepages lock, causing the bdi thread being blocked when attempt
to write data pages for the same inode. At the same time, f2fs_gc thread
does not notice the situation and could not help. Even the sync syscall
gets blocked.
To fix it, we could submit the cached bio first before waiting on a inode page
that is being written back.
Signed-off-by: Jin Xu <jinuxstyle@gmail.com>
[Jaegeuk Kim: add more cases to use f2fs_wait_on_page_writeback]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
bio->bi_private is not always needed. As in the reading data path,
end_read_io does not need bio_private for further using, so moving
bio_private allocation out of f2fs_bio_alloc(). Alloc it in the
submit_write_page(), and ignore it in the f2fs_readpage().
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
