A PCI-Express non-transparent bridge (NTB) is a point-to-point PCIe bus
connecting 2 systems, providing electrical isolation between the two subsystems.
A non-transparent bridge is functionally similar to a transparent bridge except
that both sides of the bridge have their own independent address domains. The
host on one side of the bridge will not have the visibility of the complete
memory or I/O space on the other side of the bridge. To communicate across the
non-transparent bridge, each NTB endpoint has one (or more) apertures exposed to
the local system. Writes to these apertures are mirrored to memory on the
remote system. Communications can also occur through the use of doorbell
registers that initiate interrupts to the alternate domain, and scratch-pad
registers accessible from both sides.
The NTB device driver is needed to configure these memory windows, doorbell, and
scratch-pad registers as well as use them in such a way as they can be turned
into a viable communication channel to the remote system. ntb_hw.[ch]
determines the usage model (NTB to NTB or NTB to Root Port) and abstracts away
the underlying hardware to provide access and a common interface to the doorbell
registers, scratch pads, and memory windows. These hardware interfaces are
exported so that other, non-mainlined kernel drivers can access these.
ntb_transport.[ch] also uses the exported interfaces in ntb_hw.[ch] to setup a
communication channel(s) and provide a reliable way of transferring data from
one side to the other, which it then exports so that "client" drivers can access
them. These client drivers are used to provide a standard kernel interface
(i.e., Ethernet device) to NTB, such that Linux can transfer data from one
system to the other in a standard way.
Signed-off-by: Jon Mason <jon.mason@intel.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bestcomm dma hardware, and some of its users like the FEC ethernet
component, is used in different FreeScale parts, including non-powerpc
parts like the ColdFire MCF547x & MCF548x families. Don't keep the
driver hidden in arch/powerpc where it is inaccessible for other arches.
.c files are moved to drivers/dma/bestcomm, while .h files are moved to
include/linux/fsl/bestcomm. Makefiles, Kconfigs and #include directives
are updated for the new file locations.
Tested by recompiling for MPC5200 with all bestcomm users enabled.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The ipack subsystem is cleaned up enough to now move out of the staging
tree, and into drivers/ipack.
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IPMI must be initialised before ACPI in order to ensure that any IPMI
services are available before ACPI driver initialisation attempts to use
any IPMI operation regions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
The BCM2835 contains a custom interrupt controller, which supports 72
interrupt sources using a 2-level register scheme. The interrupt
controller, or the HW block containing it, is referred to occasionally
as "armctrl" in the SoC documentation, hence the symbol naming in the
code.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
* Moved implementation to drivers/irchip/.
* Added devicetree documentation, and hence removed list of IRQs from
bcm2835.dtsi.
* Changed shift in MAKE_HWIRQ() and HWIRQ_BANK() from 8 to 5 to reduce
the size of the hwirq space, and pass the total size of the hwirq space
to irq_domain_add_linear(), rather than just the number of valid hwirqs;
the two are different due to the hwirq space being sparse.
* Added the interrupt controller DT node to the top-level of the DT,
rather than nesting it inside a /axi node. Hence, changed the reg value
since /axi had a ranges property. This seems simpler to me, but I'm not
sure if everyone will like this change or not.
* Don't set struct irq_domain_ops.map = irq_domain_simple_map, hence
removing the need to patch include/linux/irqdomain.h or
kernel/irq/irqdomain.c.
* Simplified armctrl_of_init() using of_iomap().
* Removed unused IS_VALID_BANK()/IS_VALID_IRQ() macros.
* Renamed armctrl_handle_irq() to prevent possible symbol clashes.
* Made armctrl_of_init() static.
* Removed comment "Each bank is registered as a separate interrupt
controller" since this is no longer true.
* Removed FSF address from license header.
* Added my name to copyright header.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The IEEE 802.15.4 standard represents a networking protocol. I don't
exactly know why drivers for this protocol are stored into the root
'driver' folder, but better will be to store them with other
networking stuff. Currently there are only 3 drivers available for
IEEE 802.15.4 stack, so lets do it now with the smallest overhead.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a new driver *omap-ocp2scp*. This driver takes the responsibility of
creating all the devices that is connected to OCP2SCP. In the case of OMAP4,
USB2PHY is connected to ocp2scp.
This also includes device tree support for ocp2scp driver and
the documentation with device tree binding information is updated.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
VFIO is a secure user level driver for use with both virtual machines
and user level drivers. VFIO makes use of IOMMU groups to ensure the
isolation of devices in use, allowing unprivileged user access. It's
intended that VFIO will replace KVM device assignment and UIO drivers
(in cases where the target platform includes a sufficiently capable
IOMMU).
New in this version of VFIO is support for IOMMU groups managed
through the IOMMU core as well as a rework of the API, removing the
group merge interface. We now go back to a model more similar to
original VFIO with UIOMMU support where the file descriptor obtained
from /dev/vfio/vfio allows access to the IOMMU, but only after a
group is added, avoiding the previous privilege issues with this type
of model. IOMMU support is also now fully modular as IOMMUs have
vastly different interface requirements on different platforms. VFIO
users are able to query and initialize the IOMMU model of their
choice.
Please see the follow-on Documentation commit for further description
and usage example.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds framework support for PWM (pulse width modulation) devices.
The is a barebone PWM API already in the kernel under include/linux/pwm.h,
but it does not allow for multiple drivers as each of them implements the
pwm_*() functions.
There are other PWM framework patches around from Bill Gatliff. Unlike
his framework this one does not change the existing API for PWMs so that
this framework can act as a drop in replacement for the existing API.
Why another framework?
Several people argue that there should not be another framework for PWMs
but they should be integrated into one of the existing frameworks like led
or hwmon. Unlike these frameworks the PWM framework is agnostic to the
purpose of the PWM. In fact, a PWM can drive a LED, but this makes the
LED framework a user of a PWM, like already done in leds-pwm.c. The gpio
framework also is not suitable for PWMs. Every gpio could be turned into
a PWM using timer based toggling, but on the other hand not every PWM hardware
device can be turned into a gpio due to the lack of hardware capabilities.
This patch does not try to improve the PWM API yet, this could be done in
subsequent patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
[thierry.reding@avionic-design.de: fixup typos, kerneldoc comments]
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
Pull the MCA deletion branch from Paul Gortmaker:
"It was good that we could support MCA machines back in the day, but
realistically, nobody is using them anymore. They were mostly limited
to 386-sx 16MHz CPU and some 486 class machines and never more than
64MB of RAM. Even the enthusiast hobbyist community seems to have
dried up close to ten years ago, based on what you can find searching
various websites dedicated to the relatively short lived hardware.
So lets remove the support relating to CONFIG_MCA. There is no point
carrying this forward, wasting cycles doing routine maintenance on it;
wasting allyesconfig build time on validating it, wasting I/O on git
grep'ping over it, and so on."
Let's see if anybody screams. It generally has compiled, and James
Bottomley pointed out that there was a MCA extension from NCR that
allowed for up to 4GB of memory and PPro-class machines. So in *theory*
there may be users out there.
But even James (technically listed as a maintainer) doesn't actually
have a system, and while Alan Cox claims to have a machine in his cellar
that he offered to anybody who wants to take it off his hands, he didn't
argue for keeping MCA support either.
So we could bring it back. But somebody had better speak up and talk
about how they have actually been using said MCA hardware with modern
kernels for us to do that. And David already took the patch to delete
all the networking driver code (commit a5e371f61a: "drivers/net:
delete all code/drivers depending on CONFIG_MCA").
* 'delete-mca' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MCA: delete all remaining traces of microchannel bus support.
scsi: delete the MCA specific drivers and driver code
serial: delete the MCA specific 8250 support.
arm: remove ability to select CONFIG_MCA
Here is the big staging tree pull request for the 3.5-rc1 merge window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out of
the staging tree, to their respective "real" portions of the kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q8MACgkQMUfUDdst+ymjogCguo8fANFVlPWeZGeoBTL+aQfQ
yTkAoLE0codmh+2SvhulYgyU1Wh6ZDK2
=nJ2F
-----END PGP SIGNATURE-----
Merge tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree changes from Greg Kroah-Hartman:
"Here is the big staging tree pull request for the 3.5-rc1 merge
window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out
of the staging tree, to their respective "real" portions of the
kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up various trivial conflicts, along with a non-trivial one found
in -next and pointed out by Olof Johanssen: a clean - but incorrect -
merge of the arch/arm/boot/dts/at91sam9g20.dtsi file. Fix up manually
as per Stephen Rothwell.
* tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (536 commits)
Staging: bcm: Remove two unused variables from Adapter.h
Staging: bcm: Removes the volatile type definition from Adapter.h
Staging: bcm: Rename all "INT" to "int" in Adapter.h
Staging: bcm: Fix warning: __packed vs. __attribute__((packed)) in Adapter.h
Staging: bcm: Correctly format all comments in Adapter.h
Staging: bcm: Fix all whitespace issues in Adapter.h
Staging: bcm: Properly format braces in Adapter.h
Staging: ipack/bridges/tpci200: remove unneeded casts
Staging: ipack/bridges/tpci200: remove TPCI200_SHORTNAME constant
Staging: ipack: remove board_name and bus_name fields from struct ipack_device
Staging: ipack: improve the register of a bus and a device in the bus.
staging: comedi: cleanup all the comedi_driver 'detach' functions
staging: comedi: remove all 'default N' in Kconfig
staging: line6/config.h: Delete unused header
staging: gdm72xx depends on NET
staging: gdm72xx: Set up parent link in sysfs for gdm72xx devices
staging: drm/omap: initial dmabuf/prime import support
staging: drm/omap: dmabuf/prime mmap support
pstore/ram: Add ECC support
pstore/ram: Switch to persistent_ram routines
...
Hardware with MCA bus is limited to 386 and 486 class machines
that are now 20+ years old and typically with less than 32MB
of memory. A quick search on the internet, and you see that
even the MCA hobbyist/enthusiast community has lost interest
in the early 2000 era and never really even moved ahead from
the 2.4 kernels to the 2.6 series.
This deletes anything remaining related to CONFIG_MCA from core
kernel code and from the x86 architecture. There is no point in
carrying this any further into the future.
One complication to watch for is inadvertently scooping up
stuff relating to machine check, since there is overlap in
the TLA name space (e.g. arch/x86/boot/mca.c).
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: x86@kernel.org
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tegra AHB Bus conforms to the AMBA Specification (Rev 2.0) Advanced
High-performance Bus (AHB) architecture.
The AHB Arbiter controls AHB bus master arbitration. This effectively
forms a second level of arbitration for access to the memory
controller through the AHB Slave Memory device. The AHB pre-fetch
logic can be configured to enhance performance for devices doing
sequential access. Each AHB master is assigned to either the high or
low priority bin. Both Tegra20/30 have this AHB bus.
Some of configuration params could be passed from DT too if needed.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
EMIF is an SDRAM controller used in various Texas Instruments
SoCs. EMIF supports, based on its revision, one or more of
LPDDR2/DDR2/DDR3 protocols.
Add the basic infrastructure for EMIF driver that includes
driver registration, probe, parsing of platform data etc.
Signed-off-by: Aneesh V <aneesh@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
[santosh.shilimkar@ti.com: Moved to drivers/memory from drivers/misc]
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This moves the VME core, VME board drivers, and VME bridge drivers out
of the drivers/staging/vme/ area to drivers/vme/.
The VME device drivers have not moved out yet due to some API questions
they are still working through, that should happen soon, hopefully.
Cc: Martyn Welch <martyn.welch@ge.com>
Cc: Manohar Vanga <manohar.vanga@cern.ch>
Cc: Vincent Bossier <vincent.bossier@gmail.com>
Cc: "Emilio G. Cota" <cota@braap.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take the core support + the kfifo buffer implentation out of
staging. Whilst we are far from done in improving this subsystem
it is now at a stage where the userspae interfaces (provided by
the core) can be considered stable.
Drivers will follow over a longer time scale.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
External connector class (extcon) is based on and an extension of
Android kernel's switch class located at linux/drivers/switch/.
This patch provides the before-extension switch class moved to the
location where the extcon will be located (linux/drivers/extcon/) and
updates to handle class properly.
The before-extension class, switch class of Android kernel, commits
imported are:
switch: switch class and GPIO drivers. (splitted)
Author: Mike Lockwood <lockwood@android.com>
switch: Use device_create instead of device_create_drvdata.
Author: Arve Hjønnevåg <arve@android.com>
In this patch, upon the commits of Android kernel, we have added:
- Relocated and renamed for extcon.
- Comments, module name, and author information are updated
- Code clean for successing patches
- Bugfix: enabling write access without write functions
- Class/device/sysfs create/remove handling
- Added comments about uevents
- Format changes for extcon_dev_register() to have a parent dev.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
Changes from v7
- Compiler error fixed when it is compiled as a module.
- Removed out-of-date Kconfig entry
Changes from v6
- Updated comment/strings
- Revised "Android-compatible" mode.
* Automatically activated if CONFIG_ANDROID && !CONFIG_ANDROID_SWITCH
* Creates /sys/class/switch/*, which is a copy of /sys/class/extcon/*
Changes from v5
- Split the patch
- Style fixes
- "Android-compatible" mode is enabled by Kconfig option.
Changes from v2
- Updated name_show
- Sysfs entries are handled by class itself.
- Updated the method to add/remove devices for the class
- Comments on uevent send
- Able to become a module
- Compatible with Android platform
Changes from RFC
- Renamed to extcon (external connector) from multistate switch
- Added a seperated directory (drivers/extcon)
- Added kerneldoc comments
- Removed unused variables from extcon_gpio.c
- Added ABI Documentation.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull HSI (High Speed Synchronous Serial Interface) framework from Carlos Chinea:
"The High Speed Synchronous Serial Interface (HSI) is a serial
interface mainly used for connecting application engines (APE) with
cellular modem engines (CMT) in cellular handsets.
The framework is currently being used for some people and we would
like to see it integrated into the kernel for 3.3. There is no HW
controller drivers in this pull, but some people have already some of
them pending which they would like to push as soon as this integrated.
I am also working on the acceptance for an TI OMAP one, based on a
compatible legacy version of the interface called SSI."
Ok, so it didn't get into 3.3, but here it is pulled into 3.4.
Several people piped up to say "yeah, we want this".
* 'for-next' of git://gitorious.org/kernel-hsi/kernel-hsi:
HSI: hsi_char: Update ioctl-number.txt
HSI: Add HSI API documentation
HSI: hsi_char: Add HSI char device kernel configuration
HSI: hsi_char: Add HSI char device driver
HSI: hsi: Introducing HSI framework
This new subsystem provides a common way to talk to secondary processors
on an SoC, e.g. a DSP, GPU or service processor, using virtio as the
transport. In the long run, it should replace a few dozen vendor
specific ways to do the same thing, which all never made it into the
upstream kernel. There is a broad agreement that rpmsg is the way to
go here and several vendors have started working on replacing their
own subsystems.
Two branches each add one virtio protocol number. Fortunately the
numbers were agreed upon in advance, so there are only context changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SC55
-----END PGP SIGNATURE-----
Merge tag 'rpmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "remoteproc/rpmsg: new subsystem" from Arnd Bergmann:
"This new subsystem provides a common way to talk to secondary
processors on an SoC, e.g. a DSP, GPU or service processor, using
virtio as the transport. In the long run, it should replace a few
dozen vendor specific ways to do the same thing, which all never made
it into the upstream kernel. There is a broad agreement that rpmsg is
the way to go here and several vendors have started working on
replacing their own subsystems.
Two branches each add one virtio protocol number. Fortunately the
numbers were agreed upon in advance, so there are only context
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial protocol number conflict due to the mentioned additions
next to each other.
* tag 'rpmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
remoteproc: cleanup resource table parsing paths
remoteproc: remove the hardcoded vring alignment
remoteproc/omap: remove the mbox_callback limitation
remoteproc: remove the single rpmsg vdev limitation
remoteproc: safer boot/shutdown order
remoteproc: remoteproc_rpmsg -> remoteproc_virtio
remoteproc: resource table overhaul
rpmsg: fix build warning when dma_addr_t is 64-bit
rpmsg: fix published buffer length in rpmsg_recv_done
rpmsg: validate incoming message length before propagating
rpmsg: fix name service endpoint leak
remoteproc/omap: two Kconfig fixes
remoteproc: make sure we're parsing a 32bit firmware
remoteproc: s/big switch/lookup table/
remoteproc: bail out if firmware has different endianess
remoteproc: don't use virtio's weak barriers
rpmsg: rename virtqueue_add_buf_gfp to virtqueue_add_buf
rpmsg: depend on EXPERIMENTAL
remoteproc: depend on EXPERIMENTAL
rpmsg: add Kconfig menu
...
Conflicts:
include/linux/virtio_ids.h
Fix build error caused by commit:
6222d7a177
telephony: Move to staging
The telephony driver was moved to staging but the Makefiles
weren't updated
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a virtio-based inter-processor communication bus, which enables
kernel drivers to communicate with entities, running on remote
processors, over shared memory using a simple messaging protocol.
Every pair of AMP processors share two vrings, which are used to send
and receive the messages over shared memory.
The header of every message sent on the rpmsg bus contains src and dst
addresses, which make it possible to multiplex several rpmsg channels on
the same vring.
Every rpmsg channel is a device on this bus. When a channel is added,
and an appropriate rpmsg driver is found and probed, it is also assigned
a local rpmsg address, which is then bound to the driver's callback.
When inbound messages carry the local address of a bound driver,
its callback is invoked by the bus.
This patch provides a kernel interface only; user space interfaces
will be later exposed by kernel users of this rpmsg bus.
Designed with Brian Swetland <swetland@google.com>.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au> (virtio_ids.h)
Cc: Brian Swetland <swetland@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Modern SoCs typically employ a central symmetric multiprocessing (SMP)
application processor running Linux, with several other asymmetric
multiprocessing (AMP) heterogeneous processors running different instances
of operating system, whether Linux or any other flavor of real-time OS.
Booting a remote processor in an AMP configuration typically involves:
- Loading a firmware which contains the OS image
- Allocating and providing it required system resources (e.g. memory)
- Programming an IOMMU (when relevant)
- Powering on the device
This patch introduces a generic framework that allows drivers to do
that. In the future, this framework will also include runtime power
management and error recovery.
Based on (but now quite far from) work done by Fernando Guzman Lugo
<fernando.lugo@ti.com>.
ELF loader was written by Mark Grosen <mgrosen@ti.com>, based on
msm's Peripheral Image Loader (PIL) by Stephen Boyd <sboyd@codeaurora.org>.
Designed with Brian Swetland <swetland@google.com>.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Brian Swetland <swetland@google.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Add a means of getting platform data for the SDHCI PCI
devices. The data is stored against the slot not the
device in order to support multi-slot devices.
The data allows platform-specific setup (such as getting
GPIO numbers from firmware or setting up wl12xx for SDIO)
to be done in platform support files instead of the
sdhci-pci driver.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adds HSI framework in to the linux kernel.
High Speed Synchronous Serial Interface (HSI) is a
serial interface mainly used for connecting application
engines (APE) with cellular modem engines (CMT) in cellular
handsets.
HSI provides multiplexing for up to 16 logical channels,
low-latency and full duplex communication.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1519 commits)
staging: et131x: Remove redundant check and return statement
staging: et131x: Mainly whitespace changes to appease checkpatch
staging: et131x: Remove last of the forward declarations
staging: et131x: Remove even more forward declarations
staging: et131x: Remove yet more forward declarations
staging: et131x: Remove more forward declarations
staging: et131x: Remove forward declaration of et131x_adapter_setup
staging: et131x: Remove some forward declarations
staging: et131x: Remove unused rx_ring.recv_packet_pool
staging: et131x: Remove call to find pci pm capability
staging: et131x: Remove redundant et131x_reset_recv() call
staging: et131x: Remove unused rx_ring.recv_buffer_pool
Staging: bcm: Fix three initialization errors in InterfaceDld.c
Staging: bcm: Fix coding style issues in InterfaceDld.c
staging:iio:dac: Add AD5360 driver
staging:iio:trigger:bfin-timer: Fix compile error
Staging: vt6655: add some range checks before memcpy()
Staging: vt6655: whitespace fixes to iotcl.c
Staging: vt6656: add some range checks before memcpy()
Staging: vt6656: whitespace cleanups in ioctl.c
...
Fix up conflicts in:
- drivers/{Kconfig,Makefile}, drivers/staging/{Kconfig,Makefile}:
vg driver movement
- drivers/staging/brcm80211/brcmfmac/{dhd_linux.c,mac80211_if.c}:
driver removal vs now stale changes
- drivers/staging/rtl8192e/r8192E_core.c:
driver removal vs now stale changes
- drivers/staging/et131x/et131*:
driver consolidation into one file, tried to do fixups
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
This creates a subsystem for handling of pin control devices.
These are devices that control different aspects of package
pins.
Currently it handles pinmuxing, i.e. assigning electronic
functions to groups of pins on primarily PGA and BGA type of
chip packages which are common in embedded systems.
The plan is to also handle other I/O pin control aspects
such as biasing, driving, input properties such as
schmitt-triggering, load capacitance etc within this
subsystem, to remove a lot of ARM arch code as well as
feature-creepy GPIO drivers which are implementing the same
thing over and over again.
This is being done to depopulate the arch/arm/* directory
of such custom drivers and try to abstract the infrastructure
they all need. See the Documentation/pinctrl.txt file that is
part of this patch for more details.
ChangeLog v1->v2:
- Various minor fixes from Joe's and Stephens review comments
- Added a pinmux_config() that can invoke custom configuration
with arbitrary data passed in or out to/from the pinmux driver
ChangeLog v2->v3:
- Renamed subsystem folder to "pinctrl" since we will likely
want to keep other pin control such as biasing in this
subsystem too, so let us keep to something generic even though
we're mainly doing pinmux now.
- As a consequence, register pins as an abstract entity separate
from the pinmux. The muxing functions will claim pins out of the
pin pool and make sure they do not collide. Pins can now be
named by the pinctrl core.
- Converted the pin lookup from a static array into a radix tree,
I agreed with Grant Likely to try to avoid any static allocation
(which is crap for device tree stuff) so I just rewrote this
to be dynamic, just like irq number descriptors. The
platform-wide definition of number of pins goes away - this is
now just the sum total of the pins registered to the subsystem.
- Make sure mappings with only a function name and no device
works properly.
ChangeLog v3->v4:
- Define a number space per controller instead of globally,
Stephen and Grant requested the same thing so now maps need to
define target controller, and the radix tree of pin descriptors
is a property on each pin controller device.
- Add a compulsory pinctrl device entry to the pinctrl mapping
table. This must match the pinctrl device, like "pinctrl.0"
- Split the file core.c in two: core.c and pinmux.c where the
latter carry all pinmux stuff, the core is for generic pin
control, and use local headers to access functionality between
files. It is now possible to implement a "blank" pin controller
without pinmux capabilities. This split will make new additions
like pindrive.c, pinbias.c etc possible for combined drivers
and chunks of functionality which is a GoodThing(TM).
- Rewrite the interaction with the GPIO subsystem - the pin
controller descriptor now handles this by defining an offset
into the GPIO numberspace for its handled pin range. This is
used to look up the apropriate pin controller for a GPIO pin.
Then that specific GPIO range is matched 1-1 for the target
controller instance.
- Fixed a number of review comments from Joe Perches.
- Broke out a header file pinctrl.h for the core pin handling
stuff that will be reused by other stuff than pinmux.
- Fixed some erroneous EXPORT() stuff.
- Remove mispatched U300 Kconfig and Makefile entries
- Fixed a number of review comments from Stephen Warren, not all
of them - still WIP. But I think the new mapping that will
specify which function goes to which pin mux controller address
50% of your concerns (else beat me up).
ChangeLog v4->v5:
- Defined a "position" for each function, so the pin controller now
tracks a function in a certain position, and the pinmux maps define
what position you want the function in. (Feedback from Stephen
Warren and Sascha Hauer).
- Since we now need to request a combined function+position from
the machine mapping table that connect mux settings to drivers,
it was extended with a position field and a name field. The
name field is now used if you e.g. need to switch between two
mux map settings at runtime.
- Switched from a class device to using struct bus_type for this
subsystem. Verified sysfs functionality: seems to work fine.
(Feedback from Arnd Bergmann and Greg Kroah-Hartman)
- Define a per pincontroller list of GPIO ranges from the GPIO
pin space that can be handled by the pin controller. These can
be added one by one at runtime. (Feedback from Barry Song)
- Expanded documentation of regulator_[get|enable|disable|put]
semantics.
- Fixed a number of review comments from Barry Song. (Thanks!)
ChangeLog v5->v6:
- Create an abstract pin group concept that can sort pins into
named and enumerated groups no matter what the use of these
groups may be, one possible usecase is a group of pins being
muxed in or so. The intention is however to also use these
groups for other pin control activities.
- Make it compulsory for pinmux functions to associate with
at least one group, so the abstract pin group concept is used
to define the groups of pins affected by a pinmux function.
The pinmux driver interface has been altered so as to enforce
a function to list applicable groups per function.
- Provide an optional .group entry in the pinmux machine map
so the map can select beteween different available groups
to be used with a certain function.
- Consequent changes all over the place so that e.g. debugfs
present reasonable information about the world.
- Drop the per-pin mux (*config) function in the pinmux_ops
struct - I was afraid that this would start to be used for
things totally unrelated to muxing, we can introduce that to
the generic struct pinctrl_ops if needed. I want to keep
muxing orthogonal to other pin control subjects and not mix
these things up.
ChangeLog v6->v7:
- Make it possible to have several map entries matching the
same device, pin controller and function, but using
a different group, and alter the semantics so that
pinmux_get() will pick all matching map entries, and
store the associated groups in a list. The list will
then be iterated over at pinmux_enable()/pinmux_disable()
and corresponding driver functions called for each
defined group. Notice that you're only allowed to map
multiple *groups* to the same
{ device, pin controller, function } triplet, attempts
to map the same device to multiple pin controllers will
for example fail. This is hopefully the crucial feature
requested by Stephen Warren.
- Add a pinmux hogging field to the pinmux mapping entries,
and enable the pinmux core to hog pinmux map entries.
This currently only works for pinmuxes without assigned
devices as it looks now, but with device trees we can
look up the corresponding struct device * entries when
we register the pinmux driver, and have it hog each
pinmux map in turn, for a simple approach to
non-dynamic pin muxing. This addresses an issue from
Grant Likely that the machine should take care of as
much of the pinmux setup as possible, not the devices.
By supplying a list of hogs, it can now instruct the
core to take care of any static mappings.
- Switch pinmux group retrieveal function to grab an
array of strings representing the groups rather than an
array of unsigned and rewrite accordingly.
- Alter debugfs to show the grouplist handled by each
pinmux. Also add a list of hogs.
- Dynamically allocate a struct pinmux at pinmux_get() and
free it at pinmux_put(), then add these to the global
list of pinmuxes active as we go along.
- Go over the list of pinmux maps at pinmux_get() time
and repeatedly apply matches.
- Retrieve applicable groups per function from the driver
as a string array rather than a unsigned array, then
lookup the enumerators.
- Make the device to pinmux map a singleton - only allow the
mapping table to be registered once and even tag the
registration function with __init so it surely won't be
abused.
- Create a separate debugfs file to view the pinmux map at
runtime.
- Introduce a spin lock to the pin descriptor struct, lock it
when modifying pin status entries. Reported by Stijn Devriendt.
- Fix up the documentation after review from Stephen Warren.
- Let the GPIO ranges give names as const char * instead of some
fixed-length string.
- add a function to unregister GPIO ranges to mirror the
registration function.
- Privatized the struct pinctrl_device and removed it from the
<linux/pinctrl/pinctrl.h> API, the drivers do not need to know
the members of this struct. It is now in the local header
"core.h".
- Rename the concept of "anonymous" mux maps to "system" muxes
and add convenience macros and documentation.
ChangeLog v7->v8:
- Delete the leftover pinmux_config() function from the
<linux/pinctrl/pinmux.h> header.
- Fix a race condition found by Stijn Devriendt in pin_request()
ChangeLog v8->v9:
- Drop the bus_type and the sysfs attributes and all, we're not on
the clear about how this should be used for e.g. userspace
interfaces so let us save this for the future.
- Use the right name in MAINTAINERS, PIN CONTROL rather than
PINMUX
- Don't kfree() the device state holder, let the .remove() callback
handle this.
- Fix up numerous kerneldoc headers to have one line for the function
description and more verbose documentation below the parameters
ChangeLog v9->v10:
- pinctrl: EXPORT_SYMBOL needs export.h, folded in a patch
from Steven Rothwell
- fix pinctrl_register error handling, folded in a patch from
Axel Lin
- Various fixes to documentation text so that it's consistent.
- Removed pointless comment from drivers/Kconfig
- Removed dependency on SYSFS since we removed the bus in
v9.
- Renamed hopelessly abbreviated pctldev_* functions to the
more verbose pinctrl_dev_*
- Drop mutex properly when looking up GPIO ranges
- Return NULL instead of ERR_PTR() errors on registration of
pin controllers, using cast pointers is fragile. We can
live without the detailed error codes for sure.
Cc: Stijn Devriendt <highguy@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After many years wandering the desert, it is finally time for the
Microsoft HyperV code to move out of the staging directory. Or at least
the core hyperv bus code, and the utility driver, the rest still have
some review to get through by the various subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
With OPPs, a device may have multiple operable frequency and voltage
sets. However, there can be multiple possible operable sets and a system
will need to choose one from them. In order to reduce the power
consumption (by reducing frequency and voltage) without affecting the
performance too much, a Dynamic Voltage and Frequency Scaling (DVFS)
scheme may be used.
This patch introduces the DVFS capability to non-CPU devices with OPPs.
DVFS is a techique whereby the frequency and supplied voltage of a
device is adjusted on-the-fly. DVFS usually sets the frequency as low
as possible with given conditions (such as QoS assurance) and adjusts
voltage according to the chosen frequency in order to reduce power
consumption and heat dissipation.
The generic DVFS for devices, devfreq, may appear quite similar with
/drivers/cpufreq. However, cpufreq does not allow to have multiple
devices registered and is not suitable to have multiple heterogenous
devices with different (but simple) governors.
Normally, DVFS mechanism controls frequency based on the demand for
the device, and then, chooses voltage based on the chosen frequency.
devfreq also controls the frequency based on the governor's frequency
recommendation and let OPP pick up the pair of frequency and voltage
based on the recommended frequency. Then, the chosen OPP is passed to
device driver's "target" callback.
When PM QoS is going to be used with the devfreq device, the device
driver should enable OPPs that are appropriate with the current PM QoS
requests. In order to do so, the device driver may call opp_enable and
opp_disable at the notifier callback of PM QoS so that PM QoS's
update_target() call enables the appropriate OPPs. Note that at least
one of OPPs should be enabled at any time; be careful when there is a
transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mike Turquette <mturquette@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (99 commits)
drivers/virt: add missing linux/interrupt.h to fsl_hypervisor.c
powerpc/85xx: fix mpic configuration in CAMP mode
powerpc: Copy back TIF flags on return from softirq stack
powerpc/64: Make server perfmon only built on ppc64 server devices
powerpc/pseries: Fix hvc_vio.c build due to recent changes
powerpc: Exporting boot_cpuid_phys
powerpc: Add CFAR to oops output
hvc_console: Add kdb support
powerpc/pseries: Fix hvterm_raw_get_chars to accept < 16 chars, fixing xmon
powerpc/irq: Quieten irq mapping printks
powerpc: Enable lockup and hung task detectors in pseries and ppc64 defeconfigs
powerpc: Add mpt2sas driver to pseries and ppc64 defconfig
powerpc: Disable IRQs off tracer in ppc64 defconfig
powerpc: Sync pseries and ppc64 defconfigs
powerpc/pseries/hvconsole: Fix dropped console output
hvc_console: Improve tty/console put_chars handling
powerpc/kdump: Fix timeout in crash_kexec_wait_realmode
powerpc/mm: Fix output of total_ram.
powerpc/cpufreq: Add cpufreq driver for Momentum Maple boards
powerpc: Correct annotations of pmu registration functions
...
Fix up trivial Kconfig/Makefile conflicts in arch/powerpc, drivers, and
drivers/cpufreq
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
iommu/core: Fix build with INTR_REMAP=y && CONFIG_DMAR=n
iommu/amd: Don't use MSI address range for DMA addresses
iommu/amd: Move missing parts to drivers/iommu
iommu: Move iommu Kconfig entries to submenu
x86/ia64: intel-iommu: move to drivers/iommu/
x86: amd_iommu: move to drivers/iommu/
msm: iommu: move to drivers/iommu/
drivers: iommu: move to a dedicated folder
x86/amd-iommu: Store device alias as dev_data pointer
x86/amd-iommu: Search for existind dev_data before allocting a new one
x86/amd-iommu: Allow dev_data->alias to be NULL
x86/amd-iommu: Use only dev_data in low-level domain attach/detach functions
x86/amd-iommu: Use only dev_data for dte and iotlb flushing routines
x86/amd-iommu: Store ATS state in dev_data
x86/amd-iommu: Store devid in dev_data
x86/amd-iommu: Introduce global dev_data_list
x86/amd-iommu: Remove redundant device_flush_dte() calls
iommu-api: Add missing header file
Fix up trivial conflicts (independent additions close to each other) in
drivers/Makefile and include/linux/pci.h
Add the drivers/virt directory, which houses drivers that support
virtualization environments, and add the Freescale hypervisor management
driver.
The Freescale hypervisor management driver provides several services to
drivers and applications related to the Freescale hypervisor:
1. An ioctl interface for querying and managing partitions
2. A file interface to reading incoming doorbells
3. An interrupt handler for shutting down the partition upon receiving the
shutdown doorbell from a manager partition
4. A kernel interface for receiving callbacks when a managed partition
shuts down.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
IOMMU_API is not selected when no DMA remapping driver is
selected, but the whole drivers/iommu/ directory is only
built with IOMMU_API=y. Fixed with this patch by including
the directory with IOMMU_SUPPORT instead.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The NFC subsystem core is responsible for providing the device driver
interface. It is also responsible for providing an interface to the control
operations and data exchange.
Signed-off-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create a dedicated folder for iommu drivers, and move the base
iommu implementation over there.
Grouping the various iommu drivers in a single location will help
finding similar problems shared by different platforms, so they
could be solved once, in the iommu framework, instead of solved
differently (or duplicated) in each driver.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (33 commits)
x86: poll waiting for I/OAT DMA channel status
maintainers: add dma engine tree details
dmaengine: add TODO items for future work on dma drivers
dmaengine: Add API documentation for slave dma usage
dmaengine/dw_dmac: Update maintainer-ship
dmaengine: move link order
dmaengine/dw_dmac: implement pause and resume in dwc_control
dmaengine/dw_dmac: Replace spin_lock* with irqsave variants and enable submission from callback
dmaengine/dw_dmac: Divide one sg to many desc, if sg len is greater than DWC_MAX_COUNT
dmaengine/dw_dmac: set residue as total len in dwc_tx_status if status is !DMA_SUCCESS
dmaengine/dw_dmac: don't call callback routine in case dmaengine_terminate_all() is called
dmaengine: at_hdmac: pause: no need to wait for FIFO empty
pch_dma: modify pci device table definition
pch_dma: Support new device ML7223 IOH
pch_dma: Support I2S for ML7213 IOH
pch_dma: Fix DMA setting issue
pch_dma: modify for checkpatch
pch_dma: fix dma direction issue for ML7213 IOH video-in
dmaengine: at_hdmac: use descriptor chaining help function
dmaengine: at_hdmac: implement pause and resume in atc_control
...
Fix up trivial conflict in drivers/dma/dw_dmac.c
* 'timers-ptp-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptp: Fix dp83640 build warning when building statically
ptp: Added a clock driver for the National Semiconductor PHYTER.
ptp: Added a clock driver for the IXP46x.
ptp: Added a clock that uses the eTSEC found on the MPC85xx.
ptp: Added a brand new class driver for ptp clocks.
This function makes a deep copy of the platform data to allow it to live
in init memory. For a kernel that supports several machines and so
includes the definition for several leds-gpio devices this saves quite
some memory because all but one definition can be free'd after boot.
As the function is used by arch code it must be builtin and so cannot go
into leds-gpio.c.
[akpm@linux-foundation.org: s/CONFIG_LED_REGISTER_GPIO/CONFIG_LEDS_REGISTER_GPIO/]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: H Hartley Sweeten <hartleys@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds an infrastructure for hardware clocks that implement
IEEE 1588, the Precision Time Protocol (PTP). A class driver offers a
registration method to particular hardware clock drivers. Each clock is
presented as a standard POSIX clock.
The ancillary clock features are exposed in two different ways, via
the sysfs and by a character device.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (205 commits)
USB: EHCI: Remove SPARC_LEON {read,write}_be definitions from ehci.h
USB: UHCI: Support big endian GRUSBHC HC
sparc: add {read,write}*_be routines
USB: UHCI: Add support for big endian descriptors
USB: UHCI: Use ACCESS_ONCE rather than using a full compiler barrier
USB: UHCI: Add support for big endian mmio
usb-storage: Correct adjust_quirks to include latest flags
usb/isp1760: Fix possible unlink problems
usb/isp1760: Move function isp1760_endpoint_disable() within file.
USB: remove remaining usages of hcd->state from usbcore and fix regression
usb: musb: ux500: add configuration and build options for ux500 dma
usb: musb: ux500: add dma glue layer for ux500
usb: musb: ux500: add dma name for ux500
usb: musb: ux500: add ux500 specific code for gadget side
usb: musb: fix compile error
usb-storage: fix up the unusual_realtek device list
USB: gadget: f_audio: Fix invalid dereference of initdata
EHCI: don't rescan interrupt QHs needlessly
OHCI: fix regression caused by nVidia shutdown workaround
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
...
Move the dmaengine subsystem up early in the drivers Makefile so
DMA is made available early to all drivers, just like e.g.
regulators. Now even regulators can use DMA on the same initlevel.
As a result we can bump the ste_dma40 and coh901318 dmaengine
drivers down one initlevel to subsys_init().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Broadcom has released cards based on a new AMBA-based bus type. From a
programming point of view, this new bus type differs from AMBA and does
not use AMBA common registers. It also differs enough from SSB. We
decided that a new bus driver is needed to keep the code clean.
In its current form, the driver detects devices present on the bus and
registers them in the system. It allows registering BCMA drivers for
specified bus devices and provides them basic operations. The bus driver
itself includes two important bus managing drivers: ChipCommon core
driver and PCI(c) core driver. They are early used to allow correct
initialization.
Currently code is limited to supporting buses on PCI(e) devices, however
the driver is designed to be used also on other hosts. The host
abstraction layer is implemented and already used for PCI(e).
Support for PCI(e) hosts is working and seems to be stable (access to
80211 core was tested successfully on a few devices). We can still
optimize it by using some fixed windows, but this can be done later
without affecting any external code. Windows are just ranges in MMIO
used for accessing cores on the bus.
Cc: Greg KH <greg@kroah.com>
Cc: Michael Büsch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: George Kashperko <george@znau.edu.ua>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Botting <andy@andybotting.com>
Cc: linuxdriverproject <devel@linuxdriverproject.org>
Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead, make we enter usb/ directory on all
needed cases and enter the subdirectories from
drivers/usb/Makefile.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renesas SuperH has USBHS IP which can switch Host / Function.
This driver is designed so that Host / Function may dynamically change.
This patch add usb/renesas_usbhs and common code for SuperH USBHS.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a platform-independent hwspinlock framework.
Hardware spinlock devices are needed, e.g., in order to access data
that is shared between remote processors, that otherwise have no
alternative mechanism to accomplish synchronization and mutual exclusion
operations.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Hari Kanigeri <h-kanigeri2@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: update MAINTAINERS file due to driver movement
tty: move drivers/serial/ to drivers/tty/serial/
tty: move hvc drivers to drivers/tty/hvc/
LIO target is a full featured in-kernel target framework with the
following feature set:
High-performance, non-blocking, multithreaded architecture with SIMD
support.
Advanced SCSI feature set:
* Persistent Reservations (PRs)
* Asymmetric Logical Unit Assignment (ALUA)
* Protocol and intra-nexus multiplexing, load-balancing and failover (MC/S)
* Full Error Recovery (ERL=0,1,2)
* Active/active task migration and session continuation (ERL=2)
* Thin LUN provisioning (UNMAP and WRITE_SAMExx)
Multiprotocol target plugins
Storage media independence:
* Virtualization of all storage media; transparent mapping of IO to LUNs
* No hard limits on number of LUNs per Target; maximum LUN size ~750 TB
* Backstores: SATA, SAS, SCSI, BluRay, DVD, FLASH, USB, ramdisk, etc.
Standards compliance:
* Full compliance with IETF (RFC 3720)
* Full implementation of SPC-4 PRs and ALUA
Significant code cleanups done by Christoph Hellwig.
[jejb: fix up for new block bdev exclusive interface. Minor fixes from
Randy Dunlap and Dan Carpenter.]
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Creates a new "Near Field Communication" subsystem in drivers/nfc.
http://en.wikipedia.org/wiki/Near_Field_Communication is useful ;)
This is a driver for the pn544 NFC device. The driver transfers
ETSI messages between the device and the user space.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The tty code should be in its own subdirectory and not in the char
driver with all of the cruft that is currently there.
Based on work done by Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'ieee1394-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: remove the old IEEE 1394 driver stack
ieee1394: move init_ohci1394_dma to drivers/firewire/
Fix trivial change/delete conflict: drivers/ieee1394/eth1394.c is
getting removed, but was modified by the networking merge.
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
sh: i2c-sh7760: Replase from ctrl_* to __raw_*
sh: clkfwk: Shuffle around to match the intc split up.
sh: clkfwk: modify for_each_frequency end condition
sh: fix clk_get() error handling
sh: clkfwk: Fix fault in frequency iterator.
sh: clkfwk: Add a helper for rate rounding by divisor ranges.
sh: clkfwk: Abstract rate rounding helper.
sh: clkfwk: support clock remapping.
sh: pci: Convert to upper/lower_32_bits() helpers.
sh: mach-sdk7786: Add support for the FPGA SRAM.
sh: Provide a generic SRAM pool for tiny memories.
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
sh: pci: Support slot 4 routing on SDK7786.
sh: Fix up PMB locking.
sh: mach-sdk7786: Add support for fpga gpios.
sh: use pr_fmt for clock framework, too.
sh: remove name and id from struct clk
sh: free-without-alloc fix for sh_mobile_lcdcfb
sh: perf: Set up perf_max_events.
sh: perf: Support SH-X3 hardware counters.
...
Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c
The drivers
- ohci1394 (controller driver)
- ieee1394 (core)
- dv1394, raw1394, video1394 (userspace ABI)
- eth1394, sbp2 (protocol drivers)
are replaced by
- firewire-ohci (controller driver)
- firewire-core (core and userspace ABI)
- firewire-net, firewire-sbp2 (protocol drivers)
which are more featureful, better performing, and more secure than the older
drivers; all with a smaller and more modern code base.
The driver firedtv in drivers/media/dvb/firewire/ contains backends to both
ieee1394 and firewire-core. Its ieee1394 backend code can be removed in an
independent commit; firedtv as-is builds and works fine without ieee1394.
The driver pcilynx (an incomplete controller driver) is deleted without
replacement since PCILynx cards are extremely rare. Owners of these cards
use them with the stand-alone bus sniffer driver nosy instead.
The drivers nosy and init_ohci1394_dma which do not interact with either of
the two IEEE 1394 stacks are not affected by the ieee1394 subsystem removal.
There are still some issues with the newer firewire subsystem compared to
the older one:
- The rare and quirky controllers ALi M52xx, Apple UniNorth v1, NVIDIA
NForce2 are even less well supported by firewire-ohci than by ohci1394.
I am looking into the M52xx issue.
- The experimental firewire-net is reportedly less stable than its
experimental cousin eth1394.
- Audio playback of a certain group of audio devices (ones based on DICE
chipset with EAP; supported by prerelease FFADO code) does not work yet.
This issue is still under investigation.
- There were some ieee1394 based out-of-the-mainline drivers. Of them,
only lisight, an audio driver for iSight webcams, seems still useful.
Work is underway to reimplement it on top of firewire-core.
All these remainig issues are minor; they should not stand in the way of
overall better user experience of IEEE 1394 on Linux, together with a
reduction in support efforts and maintenance burden. The coexistence of two
IEEE 1394 kernel driver stacks in the mainline since 2.6.22 shall end now,
as announced earlier this year.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
drivers/firewire/nosy* is a stand-alone driver that does not depend on
CONFIG_FIREWIRE. Hence let make descend into drivers/firewire/ also
if that option is off.
The stand-alone driver drivers/ieee1394/init_ohci1394_dma* will soon be
moved into drivers/firewire/ too and will require the same makefile fix.
Side effect:
As mentioned in https://bugzilla.novell.com/show_bug.cgi?id=586172#c24
this influences the order in which either firewire-ohci or ohci1394 is
going to be bound to an OHCI-1394 controller in case of a modular build
of both drivers if no modprobe blacklist entries are configured.
However, a user of such a setup cannot expect deterministic behavior
anyway. The Kconfig help and the migration guide at
ieee1394.wiki.kernel.org recommend blacklist entries when a dual
IEEE 1394 stack build is being used. (The coexistence period of the two
stacks is planned to end soon.)
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-4-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To use DMA engine based DMA with MMC in a non-modular build, the DMA
engine has to initialise before MMC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This EXPERIMENTAL driver supersedes acpi_idle on
Intel Atom Processors, Intel Core i3/i5/i7 Processors
and associated Intel Xeon processors.
It does not support the Intel Core2 processor or earlier.
For kernels configured with ACPI, CONFIG_INTEL_IDLE=y
allows intel_idle to probe before the ACPI processor driver.
Booting with "intel_idle.max_cstate=0" disables intel_idle
and the system will fall back on ACPI's "acpi_idle".
Typical Linux distributions load ACPI processor module early,
making CONFIG_INTEL_IDLE=m not easily useful on ACPI platforms.
intel_idle probes all processors at module_init time.
Processors that are hot-added later will be limited
to using C1 in idle.
Signed-off-by: Len Brown <len.brown@intel.com>
Move initialization of the virtio framework before the initialization of
mtd, so that block2mtd can be used on virtio-based block devices.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=15644
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Build drivers/sh in the case of ARM-based SH-Mobile CPUs.
Shared code for the interrupt controller (INTC) and
the gpio/pinmux (PFC) is located there.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
What it is: vhost net is a character device that can be used to reduce
the number of system calls involved in virtio networking.
Existing virtio net code is used in the guest without modification.
There's similarity with vringfd, with some differences and reduced scope
- uses eventfd for signalling
- structures can be moved around in memory at any time (good for
migration, bug work-arounds in userspace)
- write logging is supported (good for migration)
- support memory table and not just an offset (needed for kvm)
common virtio related code has been put in a separate file vhost.c and
can be made into a separate module if/when more backends appear. I used
Rusty's lguest.c as the source for developing this part : this supplied
me with witty comments I wouldn't be able to write myself.
What it is not: vhost net is not a bus, and not a generic new system
call. No assumptions are made on how guest performs hypercalls.
Userspace hypervisors are supported as well as kvm.
How it works: Basically, we connect virtio frontend (configured by
userspace) to a backend. The backend could be a network device, or a tap
device. Backend is also configured by userspace, including vlan/mac
etc.
Status: This works for me, and I haven't see any crashes.
Compared to userspace, people reported improved latency (as I save up to
4 system calls per packet), as well as better bandwidth and CPU
utilization.
Features that I plan to look at in the future:
- mergeable buffers
- zero copy
- scalability tuning: figure out the best threading model to use
Note on RCU usage (this is also documented in vhost.h, near
private_pointer which is the value protected by this variant of RCU):
what is happening is that the rcu_dereference() is being used in a
workqueue item. The role of rcu_read_lock() is taken on by the start of
execution of the workqueue item, of rcu_read_unlock() by the end of
execution of the workqueue item, and of synchronize_rcu() by
flush_workqueue()/flush_work(). In the future we might need to apply
some gcc attribute or sparse annotation to the function passed to
INIT_WORK(). Paul's ack below is for this RCU usage.
(Includes fixes by Alan Cox <alan@linux.intel.com>,
David L Stevens <dlstevens@us.ibm.com>,
Chris Wright <chrisw@redhat.com>)
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
On TI's da850/omap-l138 EVM, MAC address is stored in SPI flash.
This patch changes the initialization sequence of the drivers
by moving mtd and spi ahead of net in drivers/Makefile thereby
enabling da850/omap-l138 ethernet driver to read the MAC address
while booting.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/sfi/sfi_core.c contains the generic SFI implementation.
It has a private header, sfi_core.h, for its own use and the
private use of future files in drivers/sfi/
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds the kernel side of the PPS support currently named
"LinuxPPS".
PPS means "pulse per second" and a PPS source is just a device which
provides a high precision signal each second so that an application can
use it to adjust system clock time.
Common use is the combination of the NTPD as userland program with a GPS
receiver as PPS source to obtain a wallclock-time with sub-millisecond
synchronisation to UTC.
To obtain this goal the userland programs shoud use the PPS API
specification (RFC 2783 - Pulse-Per-Second API for UNIX-like Operating
Systems, Version 1.0) which in part is implemented by this patch. It
provides a set of chars devices, one per PPS source, which can be used to
get the time signal. The RFC's functions can be implemented by accessing
to these char devices.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the TI VLYNQ high-speed, serial and packetized bus.
This bus allows external devices to be connected to the System-on-Chip and
appear in the main system memory just like any memory mapped peripheral.
It is widely used in TI's networking and multimedia SoC, including the AR7
SoC.
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fakehard is a really simple driver implementing only necessary
callbacks and serves the role of an example of driver for HardMAC
IEEE 802.15.4 device.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drivers/media drivers are linked very early - directly after
base, block, misc, and mfd and before ata, scsi, ide, input, firewire,
usb, and i2c. This breaks static build of video4linux drivers, that use
generic CPU i2c adapter drivers and the v4l2-subdev subsystem, because
during video4linux probing the v4l2-subdev core requires a struct
i2c_adapter context, which cannot be satisfied before the i2c subsystem is
initialised. Moving drivers/media after drivers/i2c fixes this problem.
The best way to trigger action is by submitting a patch:-) So, let's see
what comes out of it - on the one hand I don't see any reason why media
has to be linked this early, and nobody was able to give me one yesterday
as this problem has been discussed on linux-media, OTOH, maybe indeed it
would be better to move i2c the whole way up above media, but that'd be
much bigger of a change, I think.
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
this patch flips the order in which sata and network drivers are initialized.
SATA probing takes quite a bit of time, and with the asynchronous infrastructure
other drivers that run after it can execute in parallel. Network drivers do tend
to take some real time talking to the hardware, so running these later is
a good thing (the sata probe then runs concurrent)
This saves about 15% of my kernels boot time.
Both Dave and Jeff acked this patch and suggested it should go via the async
tree.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Move regulator earlier in link sequence.
The regulator core currently initializes as a core_initcall() to be
available early ... but then it links way late, throwing away that
benefit, so regulators available at e.g. subsys_initcall() are not
available to subsystems which need to use them.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This moves the isp1301-omap driver from the drivers/i2c/chips
directory (which will be shrinking) into a new drivers/usb/otg
directory (which will grow, with more drivers and utilities).
Note that OTG infrastructure needs to be initialized before
either host or peripheral side USB support, and may be needed
before for pure host or pure peripheral configurations.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move x86 platform specific drivers from drivers/misc/
to a new home under drivers/platform/x86/.
The community has been maintaining x86 vendor-specific
platform specific drivers under /drivers/misc/ for a few years.
The oldest ones started life under drivers/acpi.
They moved out of drivers/acpi/ because they don't actually
implement the ACPI specification, but either simply
use ACPI, or implement vendor-specific ACPI extensions.
In the future we anticipate...
drivers/misc/ will go away.
other architectures will create drivers/platform/<arch>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits)
dock: make dock driver not a module
ACPI: fix ia64 build warning
ACPI: hack around sysfs warning with link order
ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n
intel_menlo: fix build warning
panasonic-laptop: fix build
ACPICA: Update version to 20080926
ACPICA: Add support for zero-length buffer-to-string conversions
ACPICA: New: Validation for predefined ACPI methods/objects
ACPICA: Fix for implicit return compatibility
ACPICA: Fixed a couple memory leaks associated with "implicit return"
ACPICA: Optimize buffer allocation procedure
ACPICA: Fix possible memory leak, error exit path
ACPICA: Fix fault after mem allocation failure in AML parser
ACPICA: Remove unused ACPI register bit definition
ACPICA: Update version to 20080829
ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname
ACPICA: Cleanup for internal Reference Object
ACPICA: Update comments - no functional changes
ACPICA: Update for Reference ACPI_OPERAND_OBJECT
...
The Intel 7300 Memory Controller supports dynamic throttling of memory which can
be used to save power when system is idle. This driver does the memory
throttling when all CPUs are idle on such a system.
Refer to "Intel 7300 Memory Controller Hub (MCH)" datasheet
for the config space description.
Signed-off-by: Andy Henroid <andrew.d.henroid@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds kernel build support for the regulator core.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the coming of kernel based modesetting and the memory manager stuff,
the everything in one directory approach was getting very ugly and
starting to be unmanageable.
This restructures the drm along the lines of other kernel components.
It creates a drivers/gpu/drm directory and moves the hw drivers into
subdirectores. It moves the includes into an include/drm, and
sets up the unifdef for the userspace headers we should be exporting.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds a minimalistic braille screen reader support. This is meant to
be used by blind people e.g. on boot failures or when / cannot be mounted
etc and thus the userland screen readers can not work.
[akpm@linux-foundation.org: fix exports]
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jiri Kosina <jikos@jikos.cz>
Cc: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sony MemoryStick cards are used in many products manufactured by Sony.
They are available both as storage and as IO expansion cards. Currently,
only MemoryStick Pro storage cards are supported via TI FlashMedia
MemoryStick interface.
[mboton@gmail.com: biuld fix]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Miguel Boton <mboton@gmail.co>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an empty drivers/gpio directory for gpiolib infrastructure and GPIO
expanders. It will be populated by later patches.
This won't be the only place to hold such gpio_chip code. Many external chips
add a few GPIOs as secondary functionality (such as MFD drivers) and platform
code frequently needs to closely integrate GPIO and IRQ support.
This is placed *early* in the build/link sequence since it's common for other
drivers to depend on GPIOs to do their work, so they must be initialized early
in the device_initcall() sequence.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Generic Thermal sysfs driver for thermal management.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Thomas Sujith <sujith.thomas@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (27 commits)
lguest: use __PAGE_KERNEL instead of _PAGE_KERNEL
lguest: Use explicit includes rateher than indirect
lguest: get rid of lg variable assignments
lguest: change gpte_addr header
lguest: move changed bitmap to lg_cpu
lguest: move last_pages to lg_cpu
lguest: change last_guest to last_cpu
lguest: change spte_addr header
lguest: per-vcpu lguest pgdir management
lguest: make pending notifications per-vcpu
lguest: makes special fields be per-vcpu
lguest: per-vcpu lguest task management
lguest: replace lguest_arch with lg_cpu_arch.
lguest: make registers per-vcpu
lguest: make emulate_insn receive a vcpu struct.
lguest: map_switcher_in_guest() per-vcpu
lguest: per-vcpu interrupt processing.
lguest: per-vcpu lguest timers
lguest: make hypercalls use the vcpu struct
lguest: make write() operation smp aware
...
Manual conflict resolved (maybe even correctly, who knows) in
drivers/lguest/x86/core.c
This paves the way for multiple architecture support. Note that while
ioapic.c could potentially be shared with ia64, it is also moved.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds a new configuration option, which adds support for a new
early_param which gets checked in arch/x86/kernel/setup_{32,64}.c:setup_arch()
to decide wether OHCI-1394 FireWire controllers should be initialized and
enabled for physical DMA access to allow remote debugging of early problems
like issues ACPI or other subsystems which are executed very early.
If the config option is not enabled, no code is changed, and if the boot
paramenter is not given, no new code is executed, and independent of that,
all new code is freed after boot, so the config option can be even enabled
in standard, non-debug kernels.
With specialized tools, it is then possible to get debugging information
from machines which have no serial ports (notebooks) such as the printk
buffer contents, or any data which can be referenced from global pointers,
if it is stored below the 4GB limit and even memory dumps of of the physical
RAM region below the 4GB limit can be taken without any cooperation from the
CPU of the host, so the machine can be crashed early, it does not matter.
In the extreme, even kernel debuggers can be accessed in this way. I wrote
a small kgdb module and an accompanying gdb stub for FireWire which allows
to gdb to talk to kgdb using remote remory reads and writes over FireWire.
An version of the gdb stub fore FireWire is able to read all global data
from a system which is running a a normal kernel without any kernel debugger,
without any interruption or support of the system's CPU. That way, e.g. the
task struct and so on can be read and even manipulated when the physical DMA
access is granted.
A HOWTO is included in this patch, in Documentation/debugging-via-ohci1394.txt
and I've put a copy online at
ftp://ftp.suse.de/private/bk/firewire/docs/debugging-via-ohci1394.txt
It also has links to all the tools which are available to make use of it
another copy of it is online at:
ftp://ftp.suse.de/private/bk/firewire/kernel/ohci1394_dma_early-v2.diff
Signed-Off-By: Bernhard Kaindl <bk@suse.de>
Tested-By: Thomas Renninger <trenn@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Parts depend on CONFIG_LGUEST, not just CONFIG_LGUEST_GUEST
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This attempts to implement a "virtual I/O" layer which should allow
common drivers to be efficiently used across most virtual I/O
mechanisms. It will no-doubt need further enhancement.
The virtio drivers add buffers to virtio queues; as the buffers are consumed
the driver "interrupt" callbacks are invoked.
There is also a generic implementation of config space which drivers can query
to get setup information from the host.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dor Laor <dor.laor@qumranet.com>
Cc: Arnd Bergmann <arnd@arndb.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (41 commits)
ACPICA: hw: Don't carry spinlock over suspend
ACPICA: hw: remove use_lock flag from acpi_hw_register_{read, write}
ACPI: cpuidle: port idle timer suspend/resume workaround to cpuidle
ACPI: clean up acpi_enter_sleep_state_prep
Hibernation: Make sure that ACPI is enabled in acpi_hibernation_finish
ACPI: suppress uninitialized var warning
cpuidle: consolidate 2.6.22 cpuidle branch into one patch
ACPI: thinkpad-acpi: skip blanks before the data when parsing sysfs
ACPI: AC: Add sysfs interface
ACPI: SBS: Add sysfs alarm
ACPI: SBS: Add ACPI_PROCFS around procfs handling code.
ACPI: SBS: Add support for power_supply class (and sysfs)
ACPI: SBS: Make SBS reads table-driven.
ACPI: SBS: Simplify data structures in SBS
ACPI: SBS: Split host controller (ACPI0001) from SBS driver (ACPI0002)
ACPI: EC: Add new query handler to list head.
ACPI: Add acpi_bus_generate_event4() function
ACPI: Battery: add sysfs alarm
ACPI: Battery: Add sysfs support
ACPI: Battery: Misc clean-ups, no functional changes
...
Fix up conflicts in drivers/misc/thinkpad_acpi.[ch] manually
This code has been slowly rotting for about eight years. It's currently
impeding a few SCSI cleanups, and nobody seems to have hardware to test
it any more. I talked to Dave Miller about it, and he agrees we can
delete it. If anyone wants a software FC stack in future, they can
retrieve this driver from git.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Direct Cache Access (DCA) is a method for warming the CPU cache before data
is used, with the intent of lessening the impact of cache misses. This
patch adds a manager and interface for matching up client requests for DCA
services with devices that offer DCA services.
In order to use DCA, a module must do bus writes with the appropriate tag
bits set to trigger a cache read for a specific CPU. However, different
CPUs and chipsets can require different sets of tag bits, and the methods
for determining the correct bits may be simple hardcoding or may be a
hardware specific magic incantation. This interface is a way for DCA
clients to find the correct tag bits for the targeted CPU without needing
to know the specifics.
[Dave Miller] use DEFINE_SPINLOCK()
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SSB is an SoC bus used in a number of embedded devices. The most
well-known of these devices is probably the Linksys WRT54G, but there
are others as well. The bus is also used internally on the BCM43xx
and BCM44xx devices from Broadcom.
This patch also includes support for SSB ID tables in modules, so
that SSB drivers can be loaded automatically.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e5a16b1f9eec0af7cfa0830304b41c1c0833cf9f
Author: Len Brown <len.brown@intel.com>
Date: Tue Oct 2 23:44:44 2007 -0400
cpuidle: shrink diff
processor_idle.c | 440 +++++++++++++++++++++++++++++++++++++++++--
1 file changed, 429 insertions(+), 11 deletions(-)
Signed-off-by: Len Brown <len.brown@intel.com>
commit dfbb9d5aedfb18848a3e0d6f6e3e4969febb209c
Author: Len Brown <len.brown@intel.com>
Date: Wed Sep 26 02:17:55 2007 -0400
cpuidle: reduce diff size
Reduces the cpuidle processor_idle.c diff vs 2.6.22 from this
processor_idle.c | 2006 ++++++++++++++++++++++++++-----------------
1 file changed, 1219 insertions(+), 787 deletions(-)
to this:
processor_idle.c | 502 +++++++++++++++++++++++++++++++++++++++----
1 file changed, 458 insertions(+), 44 deletions(-)
...for the purpose of making the cpuilde patch less invasive
and easier to review.
no functional changes. build tested only.
Signed-off-by: Len Brown <len.brown@intel.com>
commit 889172fc915f5a7fe20f35b133cbd205ce69bf6c
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Sep 13 13:40:05 2007 -0700
cpuidle: Retain old ACPI policy for !CONFIG_CPU_IDLE
Retain the old policy in processor_idle, so that when CPU_IDLE is not
configured, old C-state policy will still be used. This provides a
clean gradual migration path from old ACPI policy to new cpuidle
based policy.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 9544a8181edc7ecc33b3bfd69271571f98ed08bc
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Sep 13 13:39:17 2007 -0700
cpuidle: Configure governors by default
Quoting Len "Do not give an option to users to shoot themselves in the foot".
Remove the configurability of ladder and menu governors as they are
needed for default policy of cpuidle. That way users will not be able to
have cpuidle without any policy loosing all C-state power savings.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8975059a2c1e56cfe83d1bcf031bcf4cb39be743
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:27:07 2007 -0400
CPUIDLE: load ACPI properly when CPUIDLE is disabled
Change the registration return codes for when CPUIDLE
support is not compiled into the kernel. As a result, the ACPI
processor driver will load properly even if CPUIDLE is unavailable.
However, it may be possible to cleanup the ACPI processor driver further
and eliminate some dead code paths.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit e0322e2b58dd1b12ec669bf84693efe0dc2414a8
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:26:06 2007 -0400
CPUIDLE: remove cpuidle_get_bm_activity()
Remove cpuidle_get_bm_activity() and updates governors
accordingly.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 18a6e770d5c82ba26653e53d240caa617e09e9ab
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:58 2007 -0400
CPUIDLE: max_cstate fix
Currently max_cstate is limited to 0, resulting in no idle processor
power management on ACPI platforms. This patch restores the value to
the array size.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1fdc0887286179b40ce24bcdbde663172e205ef0
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:40 2007 -0400
CPUIDLE: handle BM detection inside the ACPI Processor driver
Update the ACPI processor driver to detect BM activity and
limit state entry depth internally, rather than exposing such
requirements to CPUIDLE. As a result, CPUIDLE can drop this
ACPI-specific interface and become more platform independent. BM
activity is now handled much more aggressively than it was in the
original implementation, so some testing coverage may be needed to
verify that this doesn't introduce any DMA buffer under-run issues.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0ef38840db666f48e3cdd2b769da676c57228dd9
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:14 2007 -0400
CPUIDLE: menu governor updates
Tweak the menu governor to more effectively handle non-timer
break events. Non-timer break events are detected by comparing the
actual sleep time to the expected sleep time. In future revisions, it
may be more reliable to use the timer data structures directly.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit bb4d74fca63fa96cf3ace644b15ae0f12b7df5a1
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:24:40 2007 -0400
CPUIDLE: fix 'current_governor' sysfs entry
Allow the "current_governor" sysfs entry to properly handle
input terminated with '\n'.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit df3c71559bb69b125f1a48971bf0d17f78bbdf47
Author: Len Brown <len.brown@intel.com>
Date: Sun Aug 12 02:00:45 2007 -0400
cpuidle: fix IA64 build (again)
Signed-off-by: Len Brown <len.brown@intel.com>
commit a02064579e3f9530fd31baae16b1fc46b5a7bca8
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:39:27 2007 -0400
cpuidle: Remove support for runtime changing of max_cstate
Remove support for runtime changeability of max_cstate. Drivers can use
use latency APIs.
max_cstate can still be used as a boot time option and dmi override.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0912a44b13adf22f5e3f607d263aed23b4910d7e
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:39:16 2007 -0400
cpuidle: Remove ACPI cstate_limit calls from ipw2100
ipw2100 already has code to use accetable_latency interfaces to limit the
C-state. Remove the calls to acpi_set_cstate_limit and acpi_get_cstate_limit
as they are redundant.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c649a76e76be6bff1fd770d0a775798813a3f6e0
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:35:39 2007 -0400
cpuidle: compile fix for pause and resume functions
Fix the compilation failure when cpuidle is not compiled in.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Adam Belay <adam.belay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 2305a5920fb8ee6ccec1c62ade05aa8351091d71
Author: Adam Belay <abelay@novell.com>
Date: Thu Jul 19 00:49:00 2007 -0400
cpuidle: re-write
Some portions have been rewritten to make the code cleaner and lighter
weight. The following is a list of changes:
1.) the state name is now included in the sysfs interface
2.) detection, hotplug, and available state modifications are handled by
CPUIDLE drivers directly
3.) the CPUIDLE idle handler is only ever installed when at least one
cpuidle_device is enabled and ready
4.) the menu governor BM code no longer overflows
5.) the sysfs attributes are now printed as unsigned integers, avoiding
negative values
6.) a variety of other small cleanups
Also, Idle drivers are no longer swappable during runtime through the
CPUIDLE sysfs inteface. On i386 and x86_64 most idle handlers (e.g.
poll, mwait, halt, etc.) don't benefit from an infrastructure that
supports multiple states, so I think using a more general case idle
handler selection mechanism would be cleaner.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit df25b6b56955714e6e24b574d88d1fd11f0c3ee5
Author: Len Brown <len.brown@intel.com>
Date: Tue Jul 24 17:08:21 2007 -0400
cpuidle: fix IA64 buid
Signed-off-by: Len Brown <len.brown@intel.com>
commit fd6ada4c14488755ff7068860078c437431fbccd
Author: Adrian Bunk <bunk@stusta.de>
Date: Mon Jul 9 11:33:13 2007 -0700
cpuidle: static
make cpuidle_replace_governor() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c1d4a2cebcadf2429c0c72e1d29aa2a9684c32e0
Author: Adrian Bunk <bunk@stusta.de>
Date: Tue Jul 3 00:54:40 2007 -0400
cpuidle: static
This patch makes the needlessly global struct menu_governor static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit dbf8780c6e8d572c2c273da97ed1cca7608fd999
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Tue Jul 3 00:49:14 2007 -0400
export symbol tick_nohz_get_sleep_length
ERROR: "tick_nohz_get_sleep_length" [drivers/cpuidle/governors/menu.ko] undefined!
ERROR: "tick_nohz_get_idle_jiffies" [drivers/cpuidle/governors/menu.ko] undefined!
And please be sure to get your changes to core kernel suitably reviewed.
Cc: Adam Belay <abelay@novell.com>
Cc: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 29f0e248e7017be15f99febf9143a2cef00b2961
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Tue Jul 3 00:43:04 2007 -0400
tick.h needs hrtimer.h
It uses hrtimers.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit e40cede7d63a029e92712a3fe02faee60cc38fb4
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:40:34 2007 -0400
cpuidle: first round of documentation updates
Documentation changes based on Pavel's feedback.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 83b42be2efece386976507555c29e7773a0dfcd1
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:39:25 2007 -0400
cpuidle: add rating to the governors and pick the one with highest rating by default
Introduce a governor rating scheme to pick the right governor by default.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit d2a74b8c5e8f22def4709330d4bfc4a29209b71c
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:38:08 2007 -0400
cpuidle: make cpuidle sysfs driver governor switch off by default
Make default cpuidle sysfs to show current_governor and current_driver in
read-only mode. More elaborate available_governors and available_drivers with
writeable current_governor and current_driver interface only appear with
"cpuidle_sysfs_switch" boot parameter.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1f60a0e80bf83cf6b55c8845bbe5596ed8f6307b
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:37:00 2007 -0400
cpuidle: menu governor: change the early break condition
Change the C-state early break out algorithm in menu governor.
We only look at early breakouts that result in wakeups shorter than idle
state's target_residency. If such a breakout is frequent enough, eliminate
the particular idle state upto a timeout period.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 45a42095cf64b003b4a69be3ce7f434f97d7af51
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:35:38 2007 -0400
cpuidle: fix uninitialized variable in sysfs routine
Fix the uninitialized usage of ret.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 80dca7cdba3e6ee13eae277660873ab9584eb3be
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:34:16 2007 -0400
cpuidle: reenable /proc/acpi//power interface for the time being
Keep /proc/acpi/processor/CPU*/power around for a while as powertop depends
on it. It will be marked deprecated and removed in future. powertop can use
cpuidle interfaces instead.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 589c37c2646c5e3813a51255a5ee1159cb4c33fc
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:32:37 2007 -0400
cpuidle: menu governor and hrtimer compile fix
Compile fix for menu governor.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0ba80bd9ab3ed304cb4f19b722e4cc6740588b5e
Author: Len Brown <len.brown@intel.com>
Date: Thu May 31 22:51:43 2007 -0400
cpuidle: build fix - cpuidle vs ipw2100 module
ERROR: "acpi_set_cstate_limit" [drivers/net/wireless/ipw2100.ko] undefined!
Signed-off-by: Len Brown <len.brown@intel.com>
commit d7d8fa7f96a7f7682be7c6cc0cc53fa7a18c3b58
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:47:07 2007 -0400
cpuidle: add the 'menu' governor
Here is my first take at implementing an idle PM governor that takes
full advantage of NO_HZ. I call it the 'menu' governor because it
considers the full list of idle states before each entry.
I've kept the implementation fairly simple. It attempts to guess the
next residency time and then chooses a state that would meet at least
the break-even point between power savings and entry cost. To this end,
it selects the deepest idle state that satisfies the following
constraints:
1. If the idle time elapsed since bus master activity was detected
is below a threshold (currently 20 ms), then limit the selection
to C2-type or above.
2. Do not choose a state with a break-even residency that exceeds
the expected time remaining until the next timer interrupt.
3. Do not choose a state with a break-even residency that exceeds
the elapsed time between the last pair of break events,
excluding timer interrupts.
This governor has an advantage over "ladder" governor because it
proactively checks how much time remains until the next timer interrupt
using the tick infrastructure. Also, it handles device interrupt
activity more intelligently by not including timer interrupts in break
event calculations. Finally, it doesn't make policy decisions using the
number of state entries, which can have variable residency times (NO_HZ
makes these potentially very large), and instead only considers sleep
time deltas.
The menu governor can be selected during runtime using the cpuidle sysfs
interface like so:
"echo "menu" > /sys/devices/system/cpu/cpuidle/current_governor"
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit a4bec7e65aa3b7488b879d971651cc99a6c410fe
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:47:03 2007 -0400
cpuidle: export time until next timer interrupt using NO_HZ
Expose information about the time remaining until the next
timer interrupt expires by utilizing the dynticks infrastructure.
Also modify the main idle loop to allow dynticks to handle
non-interrupt break events (e.g. DMA). Finally, expose sleep ticks
information to external code. Thomas Gleixner is responsible for much
of the code in this patch. However, I've made some additional changes,
so I'm probably responsible if there are any bugs or oversights :)
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 2929d8996fbc77f41a5ff86bb67cdde3ca7d2d72
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:46:58 2007 -0400
cpuidle: governor API changes
This patch prepares cpuidle for the menu governor. It adds an optional
stage after idle state entry to give the governor an opportunity to
check why the state was exited. Also it makes sure the idle loop
returns after each state entry, allowing the appropriate dynticks code
to run.
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 3a7fd42f9825c3b03e364ca59baa751bb350775f
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Apr 26 00:03:59 2007 -0700
cpuidle: hang fix
Prevent hang on x86-64, when ACPI processor driver is added as a module on
a system that does not support C-states.
x86-64 expects all idle handlers to enable interrupts before returning from
idle handler. This is due to enter_idle(), exit_idle() races. Make
cpuidle_idle_call() confirm to this when there is no pm_idle_old.
Also, cpuidle look at the return values of attch_driver() and set
current_driver to NULL if attach fails on all CPUs.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 4893339a142afbd5b7c01ffadfd53d14746e858e
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:09 2007 +0800
cpuidle: add support for max_cstate limit
With CPUIDLE framework, the max_cstate (to limit max cpu c-state)
parameter is ingored. Some systems require it to ignore C2/C3
and some drivers like ipw require it too.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 43bbbbe1cb998cbd2df656f55bb3bfe30f30e7d1
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:13 2007 +0800
cpuidle: add cpuidle_fore_redetect_devices API
add cpuidle_force_redetect_devices API,
which forces all CPU redetect idle states.
Next patch will use it.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit d1edadd608f24836def5ec483d2edccfb37b1d19
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:01 2007 +0800
cpuidle: fix sysfs related issue
Fix the cpuidle sysfs issue.
a. make kobject dynamicaly allocated
b. fixed sysfs init issue to avoid suspend/resume issue
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 7169a5cc0d67b263978859672e86c13c23a5570d
Author: Randy Dunlap <randy.dunlap@oracle.com>
Date: Wed Mar 28 22:52:53 2007 -0400
cpuidle: 1-bit field must be unsigned
A 1-bit bitfield has no room for a sign bit.
drivers/cpuidle/governors/ladder.c:54:16: error: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 4658620158dc2fbd9e4bcb213c5b6fb5d05ba7d4
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Wed Mar 28 22:52:41 2007 -0400
cpuidle: fix boot hang
Patch for cpuidle boot hang reported by Larry Finger here.
http://www.ussg.iu.edu/hypermail/linux/kernel/0703.2/2025.html
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c17e168aa6e5fe3851baaae8df2fbc1cf11443a9
Author: Len Brown <len.brown@intel.com>
Date: Wed Mar 7 04:37:53 2007 -0500
cpuidle: ladder does not depend on ACPI
build fix for CONFIG_ACPI=n
In file included from drivers/cpuidle/governors/ladder.c:21:
include/acpi/processor.h:88: error: expected specifier-qualifier-list before âacpi_integerâ
include/acpi/processor.h:106: error: expected specifier-qualifier-list before âacpi_integerâ
include/acpi/processor.h:168: error: expected specifier-qualifier-list before âacpi_handleâ
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8c91d958246bde68db0c3f0c57b535962ce861cb
Author: Adrian Bunk <bunk@stusta.de>
Date: Tue Mar 6 02:29:40 2007 -0800
cpuidle: make code static
This patch makes the following needlessly global code static:
- driver.c: __cpuidle_find_driver()
- governor.c: __cpuidle_find_governor()
- ladder.c: struct ladder_governor
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0c39dc3187094c72c33ab65a64d2017b21f372d2
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Wed Mar 7 02:38:22 2007 -0500
cpu_idle: fix build break
This patch fixes a build breakage with !CONFIG_HOTPLUG_CPU and
CONFIG_CPU_IDLE.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8112e3b115659b07df340ef170515799c0105f82
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Mar 6 02:29:39 2007 -0800
cpuidle: build fix for !CPU_IDLE
Fix the compile issues when CPU_IDLE is not configured.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1eb4431e9599cd25e0d9872f3c2c8986821839dd
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:54:57 2007 -0800
cpuidle take2: Basic documentation for cpuidle
Documentation for cpuidle infrastructure
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit ef5f15a8b79123a047285ec2e3899108661df779
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:54:03 2007 -0800
cpuidle take2: Hookup ACPI C-states driver with cpuidle
Hookup ACPI C-states onto generic cpuidle infrastructure.
drivers/acpi/procesor_idle.c is now a ACPI C-states driver that registers as
a driver in cpuidle infrastructure and the policy part is removed from
drivers/acpi/processor_idle.c. We use governor in cpuidle instead.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 987196fa82d4db52c407e8c9d5dec884ba602183
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:52:57 2007 -0800
cpuidle take2: Core cpuidle infrastructure
Announcing 'cpuidle', a new CPU power management infrastructure to manage
idle CPUs in a clean and efficient manner.
cpuidle separates out the drivers that can provide support for multiple types
of idle states and policy governors that decide on what idle state to use
at run time.
A cpuidle driver can support multiple idle states based on parameters like
varying power consumption, wakeup latency, etc (ACPI C-states for example).
A cpuidle governor can be usage model specific (laptop, server,
laptop on battery etc).
Main advantage of the infrastructure being, it allows independent development
of drivers and governors and allows for better CPU power management.
A huge thanks to Adam Belay and Shaohua Li who were part of this mini-project
since its beginning and are greatly responsible for this patchset.
This patch:
Core cpuidle infrastructure.
Introduces a new abstraction layer for cpuidle:
* which manages drivers that can support multiple idles states. Drivers
can be generic or particular to specific hardware/platform
* allows pluging in multiple policy governors that can take idle state policy
decision
* The core also has a set of sysfs interfaces with which administrato can know
about supported drivers and governors and switch them at run time.
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix for the problem detected by Ingo Molnar:
enabling CONFIG_PCWATCHDOG=y crashes bzImage bootup.
The reason for this can be found in drivers/makefile
We first do:
obj-y += char/
and later we do:
obj-y += base/ block/ misc/ mfd/ net/ media/
So if we put a platform or isa or usb bus driver in char/watchdog
(which is called from the Makefile in drivers/char/Makefile)
then we didn't have the different device drivers initialized yet
(they are in drivers/base and drivers/usb and ...)
This fix makes sure that we compile the watchdog drivers after
drivers/base, drivers/misc, drivers/pci and drivers/usb.
We also do the compile after hwmon because in the future the
watchdog temperature support will use the hwmon system.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This creates drivers/of/base.c (depending on CONFIG_OF) and puts
the first trivially common bits from the prom.c files into it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: David S. Miller <davem@davemloft.net>
This is the Kconfig and Makefile to allow lguest to actually be
compiled.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This interface allows the ability to write the majority of a driver in
userspace with only a very small shell of a driver in the kernel itself.
It uses a char device and sysfs to interact with a userspace process to
process interrupts and control memory accesses.
See the docbook documentation for more details on how to use this
interface.
From: Hans J. Koch <hjk@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Xen 'grant table' driver which allows granting of access to
selected local memory pages by other virtual machines and,
symmetrically, the mapping of remote memory pages which other virtual
machines have granted access to.
This driver is a prerequisite for many of the Xen virtual device
drivers, which grant the 'device driver domain' restricted and
temporary access to only those memory pages that are currently
involved in I/O operations.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ian Pratt <ian.pratt@xensource.com>
Signed-off-by: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
This class is result of "external power" and "battery" classes merge,
as suggested by David Woodhouse. He also implemented uevent support.
Here how userspace seeing it now:
# ls /sys/class/power\ supply/
ac main-battery usb
# cat /sys/class/power\ supply/ac/type
AC
# cat /sys/class/power\ supply/usb/type
USB
# cat /sys/class/power\ supply/main-battery/type
Battery
# cat /sys/class/power\ supply/ac/online
1
# cat /sys/class/power\ supply/usb/online
0
# cat /sys/class/power\ supply/main-battery/status
Charging
# cat /sys/class/leds/h5400\:red-left/trigger
none h5400-radio timer hwtimer ac-online usb-online
main-battery-charging-or-full [main-battery-charging]
main-battery-full
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* 'juju' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (138 commits)
firewire: Convert OHCI driver to use standard goto unwinding for error handling.
firewire: Always use parens with sizeof.
firewire: Drop single buffer request support.
firewire: Add a comment to describe why we split the sg list.
firewire: Return SCSI_MLQUEUE_HOST_BUSY for out of memory cases in queuecommand.
firewire: Handle the last few DMA mapping error cases.
firewire: Allocate scsi_host up front and allocate the sbp2_device as hostdata.
firewire: Provide module aliase for backwards compatibility.
firewire: Add to fw-core-y instead of assigning fw-core-objs in Makefile.
firewire: Break out shared IEEE1394 constant to separate header file.
firewire: Use linux/*.h instead of asm/*.h header files.
firewire: Uppercase most macro names.
firewire: Coding style cleanup: no spaces after function names.
firewire: Convert card_rwsem to a regular mutex.
firewire: Clean up comment style.
firewire: Use lib/ implementation of CRC ITU-T.
CRC ITU-T V.41
firewire: Rename fw-device-cdev.c to fw-cdev.c and move header to include/linux.
firewire: Future proof the iso ioctls by adding a handle for the iso context.
firewire: Add read/write and size annotations to IOC numbers.
...
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This provides partial support for new-style I2C driver binding. It builds
on "struct i2c_board_info" declarations that identify I2C devices on a given
board. This is needed on systems with I2C devices that can't be fully probed
and/or autoconfigured, such as many embedded Linux configurations where the
way a given I2C device is wired may affect how it must be used.
There are two models for declaring such devices:
* LATE -- using a public function i2c_new_device(). This lets modules
declare I2C devices found *AFTER* a given I2C adapter becomes available.
For example, a PCI card could create adapters giving access to utility
chips on that card, and this would be used to associate those chips with
those adapters.
* EARLY -- from arch_initcall() level code, using a non-exported function
i2c_register_board_info(). This copies the declarations *BEFORE* such
an i2c_adapter becomes available, arranging that i2c_new_device() will
be called later when i2c-core registers the relevant i2c_adapter.
For example, arch/.../.../board-*.c files would declare the I2C devices
along with their platform data, and I2C devices would behave much like
PNPACPI devices. (That is, both enumerate from board-specific tables.)
To match the exported i2c_new_device(), the previously-private function
i2c_unregister_device() is now exported.
Pending later patches using these new APIs, this is effectively a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Since commit b1c1b6a3 ("IB/ipath: merge ipath_core and ib_ipath
drivers"), CONFIG_IPATH_CORE no longer exists, so there's no reason to
have a line for it in drivers/Makefile.
Pointed out by Robert P. J. Day <rpjday@mindspring.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for auxiliary displays, the ks0108 LCD controller, the
cfag12864b LCD and adds a framebuffer device: cfag12864bfb.
- Add a "auxdisplay/" folder in "drivers/" for auxiliary display
drivers.
- Add support for the ks0108 LCD Controller as a device driver. (uses
parport interface)
- Add support for the cfag12864b LCD as a device driver. (uses ks0108
LCD Controller driver)
- Add a framebuffer device called cfag12864bfb. (uses cfag12864b LCD
driver)
- Add the usual Documentation, includes, Makefiles, Kconfigs,
MAINTAINERS, CREDITS...
- Miguel Ojeda will maintain all the stuff above.
[rdunlap@xenotime.net: workqueue fixups]
[akpm@osdl.org: kconfig fix]
Signed-off-by: Miguel Ojeda Sandonis <maxextreme@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Paulo Marques <pmarques@grupopie.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As macbook/macbook pro's also have to live with a single mouse button the
following patch just enables the Macintosh device drivers menu in Kconfig +
adds the macintosh dir to the obj-* to make macbook* users happy (who use
exactly that since months....
Signed-off-by: Soeren Sonnenburg <kernel@nn7.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
web site: http://kvm.sourceforge.net
mailing list: kvm-devel@lists.sourceforge.net
(http://lists.sourceforge.net/lists/listinfo/kvm-devel)
The following patchset adds a driver for Intel's hardware virtualization
extensions to the x86 architecture. The driver adds a character device
(/dev/kvm) that exposes the virtualization capabilities to userspace. Using
this driver, a process can run a virtual machine (a "guest") in a fully
virtualized PC containing its own virtual hard disks, network adapters, and
display.
Using this driver, one can start multiple virtual machines on a host.
Each virtual machine is a process on the host; a virtual cpu is a thread in
that process. kill(1), nice(1), top(1) work as expected. In effect, the
driver adds a third execution mode to the existing two: we now have kernel
mode, user mode, and guest mode. Guest mode has its own address space mapping
guest physical memory (which is accessible to user mode by mmap()ing
/dev/kvm). Guest mode has no access to any I/O devices; any such access is
intercepted and directed to user mode for emulation.
The driver supports i386 and x86_64 hosts and guests. All combinations are
allowed except x86_64 guest on i386 host. For i386 guests and hosts, both pae
and non-pae paging modes are supported.
SMP hosts and UP guests are supported. At the moment only Intel
hardware is supported, but AMD virtualization support is being worked on.
Performance currently is non-stellar due to the naive implementation of the
mmu virtualization, which throws away most of the shadow page table entries
every context switch. We plan to address this in two ways:
- cache shadow page tables across tlb flushes
- wait until AMD and Intel release processors with nested page tables
Currently a virtual desktop is responsive but consumes a lot of CPU. Under
Windows I tried playing pinball and watching a few flash movies; with a recent
CPU one can hardly feel the virtualization. Linux/X is slower, probably due
to X being in a separate process.
In addition to the driver, you need a slightly modified qemu to provide I/O
device emulation and the BIOS.
Caveats (akpm: might no longer be true):
- The Windows install currently bluescreens due to a problem with the
virtual APIC. We are working on a fix. A temporary workaround is to
use an existing image or install through qemu
- Windows 64-bit does not work. That's also true for qemu, so it's
probably a problem with the device model.
[bero@arklinux.org: build fix]
[simon.kagstrom@bth.se: build fix, other fixes]
[uril@qumranet.com: KVM: Expose interrupt bitmap]
[akpm@osdl.org: i386 build fix]
[mingo@elte.hu: i386 fixes]
[rdreier@cisco.com: add log levels to all printks]
[randy.dunlap@oracle.com: Fix sparse NULL and C99 struct init warnings]
[anthony@codemonkey.ws: KVM: AMD SVM: 32-bit host support]
Signed-off-by: Yaniv Kamay <yaniv@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Simon Kagstrom <simon.kagstrom@bth.se>
Cc: Bernhard Rosenkraenzer <bero@arklinux.org>
Signed-off-by: Uri Lublin <uril@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This modifies Makefiles and Kconfigs to properly reflect the creation of
generic HID layer.
It also removes the dependency of BROKEN, which was introduced by the
first patch in series (see the comment). Also updates credits.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When renaming CONFIG_PS3 to CONFIG_PPC_PS3, a few occurrences have been
missed.
I also fixed up the alignment in arch/powerpc/platforms/Makefile.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Adds a PS3 system bus driver. This system bus is a virtual bus used to present
the PS3 system devices in the LDM.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Implement the time sources for i386 (acpi_pm, cyclone, hpet, pit, and tsc).
With this patch, the conversion of the i386 arch to the generic timekeeping
code should be complete.
The patch should be fairly straight forward, only adding the new clocksources.
[hirofumi@mail.parknet.co.jp: acpi_pm cleanup]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provides an API for offloading memory copies to DMA devices
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: kbuild infrastructure
IB/ipath: infiniband verbs support
IB/ipath: misc infiniband code, part 2
IB/ipath: misc infiniband code, part 1
IB/ipath: infiniband RC protocol support
IB/ipath: infiniband UC and UD protocol support
IB/ipath: infiniband header files
IB/ipath: layering interfaces used by higher-level driver code
IB/ipath: support for userspace apps using core driver
IB/ipath: sysfs and ipathfs support for core driver
IB/ipath: misc driver support code
IB/ipath: chip initialisation code, and diag support
IB/ipath: support for PCI Express devices
IB/ipath: support for HyperTransport devices
IB/ipath: core driver header files
IB/ipath: core device driver
Integrate the ipath core and OpenIB drivers into the kernel build
infrastructure. Add entry to MAINTAINERS.
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add the foundations of a new LEDs subsystem. This patch adds a class which
presents LED devices within sysfs and allows their brightness to be
controlled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Serio and gameport cores do not depend on other drivers and are
used by code living outside of drivers/input/{gameport|serio}.
Registering them at subsystem level guarantees that they are
fully initialized before anyone tries to use them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Actually I think this is more appropriate so we don't end up with 17
cases that add drivers/sn to the build lib.
Include drivers/sn when CONFIG_IA64_SGI_SN2 or CONFIG_IA64_GENERIC
is enabled.
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is a subset of the bluesmoke project core code, stripped of the NMI work
which isn't ready to merge and some of the "interesting" proc functionality
that needs reworking or just has no place in kernel. It requires no core
kernel changes except the added scrub functions already posted.
The goal is to merge further functionality only after the core code is
accepted and proven in the base kernel, and only at the point the upstream
extras are really ready to merge.
From: doug thompson <norsk5@xmission.com>
This converts EDAC to sysfs and is the final chunk neccessary before EDAC
has a stable user space API and can be considered for submission into the
base kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the core of a small SPI framework, implementing the model of a
queue of messages which complete asynchronously (with thin synchronous
wrappers on top).
- It's still less than 2KB of ".text" (ARM). If there's got to be a
mid-layer for something so simple, that's the right size budget. :)
- The guts use board-specific SPI device tables to build the driver
model tree. (Hardware probing is rarely an option.)
- This version of Kconfig includes no drivers. At this writing there
are two known master controller drivers (PXA/SSP, OMAP MicroWire)
and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML
mentions of other drivers in development.
- No userspace API. There are several implementations to compare.
Implement them like any other driver, and bind them with sysfs.
The changes from last version posted to LKML (on 11-Nov-2005) are minor,
and include:
- One bugfix (removes a FIXME), with the visible effect of making device
names be "spiB.C" where B is the bus number and C is the chipselect.
- The "caller provides DMA mappings" mechanism now has kerneldoc, for
DMA drivers that want to be fancy.
- Hey, the framework init can be subsys_init. Even though board init
logic fires earlier, at arch_init ... since the framework init is
for driver support, and the board init support uses static init.
- Various additional spec/doc clarifications based on discussions
with other folk. It adds a brief "thank you" at the end, for folk
who've helped nudge this framework into existence.
As I've said before, I think that "protocol tweaking" is the main support
that this driver framework will need to evolve.
From: Mark Underwood <basicmark@yahoo.com>
Update the SPI framework to remove a potential priority inversion case by
reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We want to link the "regular" SCSI drivers before the USB storage
driver, since historically we've always detected internal SCSI disks
before the external USB storage modules.
The link order matters for initcall ordering, and this got broken by
mistake by commit 7586269c0b which moved
the USB host controller PCI quirk handling around.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a RapidIO subsystem to the kernel. RIO is a switched fabric interconnect
used in higher-end embedded applications. The curious can look at the specs
over at http://www.rapidio.org
The core code implements enumeration/discovery, management of
devices/resources, and interfaces for RIO drivers.
There's a lot more to do to take advantages of all the hardware features.
However, this should provide a good base for folks with RIO hardware to start
contributing.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/sh/ got dropped from drivers/Makefile, so add it back in..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves the PCI quirk handling for USB host controllers from the
PCI directory to the USB directory. Follow-on patches will need to:
(a) merge these copies with the originals in the HCD reset methods.
they don't wholly agree, despite doing the very same thing; and
(b) eventually change it so "usb-handoff" is the default, to help
get more robust USB/BIOS/input/... interactions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/Makefile | 2
drivers/pci/quirks.c | 253 ---------------------------------------
drivers/usb/Makefile | 1
drivers/usb/host/Makefile | 5
drivers/usb/host/pci-quirks.c | 272 ++++++++++++++++++++++++++++++++++++++++++
5 files changed, 280 insertions(+), 253 deletions(-)
Kernel connector - new userspace <-> kernel space easy to use
communication module which implements easy to use bidirectional
message bus using netlink as it's backend. Connector was created to
eliminate complex skb handling both in send and receive message bus
direction.
Connector driver adds possibility to connect various agents using as
one of it's backends netlink based network. One must register
callback and identifier. When driver receives special netlink message
with appropriate identifier, appropriate callback will be called.
From the userspace point of view it's quite straightforward:
socket();
bind();
send();
recv();
But if kernelspace want to use full power of such connections, driver
writer must create special sockets, must know about struct sk_buff
handling... Connector allows any kernelspace agents to use netlink
based networking for inter-process communication in a significantly
easier way:
int cn_add_callback(struct cb_id *id, char *name, void (*callback) (void *));
void cn_netlink_send(struct cn_msg *msg, u32 __groups, int gfp_mask);
struct cb_id
{
__u32 idx;
__u32 val;
};
idx and val are unique identifiers which must be registered in
connector.h for in-kernel usage. void (*callback) (void *) - is a
callback function which will be called when message with above idx.val
will be received by connector core.
Using connector completely hides low-level transport layer from it's
users.
Connector uses new netlink ability to have many groups in one socket.
[ Incorporating many cleanups and fixes by myself and
Andrew Morton -DaveM ]
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the core of the multimedia communication port
framework. This is a port used to communicate with devices
with two DMA paths and a control path.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
