Qualify these with a better namespace, and prepare them for use in more
drivers.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Add the copyright information for spi-nor.c and spi-nor.h.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds support for the Macronix MX25L3255E device. Unlike the other
Macronix devices we have seen, this device supports WRITE_1_4_4 at reasonable
frequencies. Rather than masking out WRITE_1_4_4 support altogether, we now
rely on the table parameters to indicate whether or not WRITE_1_4_4 should be
used.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add Spansion S25FL032P to the list of known devices.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch refactors the fsm_read_status() and fsm_write_status() code to
support 1 or 2 byte operations, with a specified command. This allows us to
remove device/register specific code, such as the N25Q fsm_wrvcr() function.
The 'QE' configuration code is updated accordingly, with minor tweaks to ensure
the register values are only written if actually required. One notable change
in this area is that the 'W25Q_STATUS_QE' bit-field is now defined with respect
to the 'SR2' register, rather than the combined 'SR1+SR2' register which is only
used for write operations.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Update the configuration of the Macronix 'QE' bit, such that
we only set or clear the bit if required.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Support for the Macronix 32-bit addressing scheme was originally developed using
the MX25L25635E device. As is often the case, it was found that the presence of
a "WAIT" instruction was required for the "EN4B/EX4B" FSM Sequence to complete.
(It is known that the SPI FSM Controller makes certain undocumented assumptions
regarding what constitutes a valid sequence.) However, further testing
suggested that a small delay was required after issuing the "EX4B" command;
without this delay, data corruptions were observed, consistent with the device
not being ready to retrieve data. Although the issue was not fully understood,
the workaround of adding a small delay was implemented, while awaiting
clarification from Macronix.
The same behaviour has now been found with a second Macronix device, the
MX25L25655E. However, with this device, it seems that the delay is also
required after the 'EN4B' commands. This discovery has prompted us to revisit
the issue.
Although still not conclusive, further tests have suggested that the issue is
down to the SPI FSM Controller, rather than the Macronix devices. Furthermore,
an alternative workaround has emerged which is to set the WAIT time to
0x00000001, rather then 0x00000000. (Note, the WAIT instruction is used purely
for the purpose of achieving "sequence validity", rather than actually
implementing a delay!)
The issue is now being investigated by the Design and Validation teams. In the
meantime, we implement the alternative workaround, which reduces the effective
delay from 1us to 1ns.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add Macronix MX25L25655E to the list of known devices.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(0) What is the QuadSPI controller?
The QuadSPI(Quad Serial Peripheral Interface) acts as an interface to
one single or two external serial flash devices, each with up to 4
bidirectional data lines.
(1) The QuadSPI controller is driven by the LUT(Look-up Table) registers.
The LUT registers are a look-up-table for sequences of instructions.
A valid sequence consists of four LUT registers.
(2) The definition of the LUT register shows below:
---------------------------------------------------
| INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
---------------------------------------------------
There are several types of INSTRx, such as:
CMD : the SPI NOR command.
ADDR : the address for the SPI NOR command.
DUMMY : the dummy cycles needed by the SPI NOR command.
....
There are several types of PADx, such as:
PAD1 : use a singe I/O line.
PAD2 : use two I/O lines.
PAD4 : use quad I/O lines.
....
(3) Test this driver with the JFFS2 and UBIFS:
For jffs2:
-------------
#flash_eraseall /dev/mtd0
#mount -t jffs2 /dev/mtdblock0 tmp
#bonnie++ -d tmp -u 0 -s 10 -r 5
For ubifs:
-------------
#flash_eraseall /dev/mtd0
#ubiattach /dev/ubi_ctrl -m 0
#ubimkvol /dev/ubi0 -N test -m
#mount -t ubifs ubi0:test tmp
#bonnie++ -d tmp -u 0 -s 10 -r 5
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the spi_nor_match_id() to find the proper spi_device_id with the
NOR flash's name in the spi_nor_ids table.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the new SPI nor framework, and rewrite the m25p80:
(0) remove all the NOR comands.
(1) change the m25p->command to an array.
(2) implement the necessary hooks, such as m25p80_read/m25p80_write.
Tested with the m25p32.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
[Brian: rebased]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch cloned most of the m25p80.c. In theory, it adds a new spi-nor layer.
Before this patch, the layer is like:
MTD
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
After this patch, the layer is like:
MTD
------------------------
spi-nor
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
With the spi-nor controller driver(Freescale Quadspi), it looks like:
MTD
------------------------
spi-nor
------------------------
fsl-quadspi
------------------------
SPI NOR chip
New APIs:
spi_nor_scan: used to scan a spi-nor flash.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
[Brian: rebased to include additional m25p_ids[] entry]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- A few SPI NOR ID definitions
- Kill the NAND "max pagesize" restriction
- Fix some x16 bus-width NAND support
- Add NAND JEDEC parameter page support
- DT bindings for NAND ECC
- GPMI NAND updates (subpage reads)
- More OMAP NAND refactoring
- New STMicro SPI NOR driver (now in 40 patches!)
- A few other random bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=CKih
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
- A few SPI NOR ID definitions
- Kill the NAND "max pagesize" restriction
- Fix some x16 bus-width NAND support
- Add NAND JEDEC parameter page support
- DT bindings for NAND ECC
- GPMI NAND updates (subpage reads)
- More OMAP NAND refactoring
- New STMicro SPI NOR driver (now in 40 patches!)
- A few other random bugfixes
* tag 'for-linus-20140405' of git://git.infradead.org/linux-mtd: (120 commits)
Fix index regression in nand_read_subpage
mtd: diskonchip: mem resource name is not optional
mtd: nand: fix mention to CONFIG_MTD_NAND_ECC_BCH
mtd: nand: fix GET/SET_FEATURES address on 16-bit devices
mtd: omap2: Use devm_ioremap_resource()
mtd: denali_dt: Use devm_ioremap_resource()
mtd: devices: elm: update DRIVER_NAME as "omap-elm"
mtd: devices: elm: configure parallel channels based on ecc_steps
mtd: devices: elm: clean elm_load_syndrome
mtd: devices: elm: check for hardware engine's design constraints
mtd: st_spi_fsm: Succinctly reorganise .remove()
mtd: st_spi_fsm: Allow loop to run at least once before giving up CPU
mtd: st_spi_fsm: Correct vendor name spelling issue - missing "M"
mtd: st_spi_fsm: Avoid duplicating MTD core code
mtd: st_spi_fsm: Remove useless consts from function arguments
mtd: st_spi_fsm: Convert ST SPI FSM (NOR) Flash driver to new DT partitions
mtd: st_spi_fsm: Move runtime configurable msg sequences into device's struct
mtd: st_spi_fsm: Supply the W25Qxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the S25FLxxx chip specific configuration call-back
mtd: st_spi_fsm: Supply the MX25xxx chip specific configuration call-back
...
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Commit 7351d3a5db added an index variable
as part of fixing checkpatch warnings, presumably as a tool to make some
long lines shorter, however it only set that index in the case of there
being no gaps in eccpos for the fragment being read. Which means the
later step of filling ecccode from oob_poi will use the wrong indexing
into eccpos in that case.
This patch restores the behaviour that existed prior to that change.
Signed-off-by: Ron Lee <ron@debian.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
access to UBI volumes. It is useful for those who want to use squashfs on top
of raw flash devices. UBI will provide bit-flip handling and wear-levelling in
this case (e.g., if there are other UBI volumes with R/W UBIFS too).
The driver is actually pretty small and it is part of the UBI kernel subsystem.
Delivered by Ezequiel Garcia, along with a piece of documentation on the MTD
web site and the user-space tool for creating and removing block devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SGfE
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.15-rc1' of git://git.infradead.org/linux-ubifs
Pull ubifs updates from Artem Bityutskiy:
"This pull request includes the 'ubiblock' driver which provides R/O
block access to UBI volumes. It is useful for those who want to use
squashfs on top of raw flash devices. UBI will provide bit-flip
handling and wear-levelling in this case (e.g., if there are other UBI
volumes with R/W UBIFS too).
The driver is actually pretty small and it is part of the UBI kernel
subsystem. Delivered by Ezequiel Garcia, along with a piece of
documentation on the MTD web site and the user-space tool for creating
and removing block devices"
* tag 'upstream-3.15-rc1' of git://git.infradead.org/linux-ubifs:
UBI: block: Remove __initdata from ubiblock_param_ops
UBI: make UBI_IOCVOLCRBLK take a parameter for future usage
UBI: rename block device ioctls
UBI: block: Use ENOSYS as return value when CONFIG_UBIBLOCK=n
UBI: block: Add CONFIG_BLOCK dependency
UBI: block: Use 'u64' for the 64-bit dividend
UBI: block: Mark init-only symbol as __initdata
UBI: block: do not use term "attach"
UBI: R/O block driver on top of UBI volumes
Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7ArIACgkQMUfUDdst+ylS+gCfcJr0Zo2v5aWnqD7rFtFETmFI
LhcAoNTQ4cvlVdxnI0driWCWFYxLj6at
=aj+L
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while"
* tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (118 commits)
extcon: Move OF helper function to extcon core and change function name
extcon: of: Remove unnecessary function call by using the name of device_node
extcon: gpio: Use SIMPLE_DEV_PM_OPS macro
extcon: palmas: Use SIMPLE_DEV_PM_OPS macro
mei: don't use deprecated DEFINE_PCI_DEVICE_TABLE macro
mei: amthif: fix checkpatch error
mei: client.h fix checkpatch errors
mei: use cl_dbg where appropriate
mei: fix Unnecessary space after function pointer name
mei: report consistently copy_from/to_user failures
mei: drop pr_fmt macros
mei: make me hw headers private to me hw.
mei: fix memory leak of pending write cb objects
mei: me: do not reset when less than expected data is received
drivers: mcb: Fix build error discovered by 0-day bot
cs5535-mfgpt: Simplify dependencies
spmi: pm: drop bus-level PM suspend/resume routines
spmi: pmic_arb: make selectable on ARCH_QCOM
Drivers: hv: vmbus: Increase the limit on the number of pfns we can handle
pch_phub: Report error writing MAC back to user
...
Passing a name to request_mem_region() isn't optional and can't just
be NULL. Passing NULL causes a NULL ptr deref later in the boot
process.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Tested-by: Alexander Shiyan <shc_work@mail.ru>
Cc: <stable@vger.kernel.org> # 3.14
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Mention to CONFIG_MTD_ECC_BCH in the warning message can be confusing as this
doesn't match the exact name of the configuration option.
This warning showed up once to me when I was starting to set up BCH. After
checking my .config file, it took a moment before realizing it is
CONFIG_MTD_NAND_ECC_BCH instead of CONFIG_MTD_ECC_BCH.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource(). Also,
'unsigned long mem_size' is removed from 'struct omap_nand_info',
because the 'mem_size' variable is not necessary anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_ioremap_resource() in order to make the code
simpler, and remove redundant return value check of
platform_get_resource_byname() because the value is
checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ELM hardware can process up to maximum of 8 hannels in parallel for
ECC error detection. Currently the number of channels getting configured for
processing is static determined by macro ERROR_VECTOR_MAX. However, the actual
number of channels that need to be processed is the ECC step number.
This patch just avoids configuring extra unused channels.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch refactors elm_load_syndrome() to make it scalable for newer
ECC schemes by removing scheme specific macros (like ECC_BYTES*xx),
and instead using ECC control information passed during elm_config.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ELM hardware engine is used by BCH ecc-schemes for detecting and locating ECC
errors. This patch adds the following checks for ELM hardware engine:
- ELM internal buffers are of 1K,
so it cannot process data with ecc-step-size > 1K.
- ELM engine can execute upto maximum of 8 threads in parallel,
so in *page-mode* (when complete page is processed in single iteration),
ELM cannot support ecc-steps > 8.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
You cannot mark these parameters as __initdata.
Otherwise the data is gone upon module exit.
Fixes:
[ 172.045465] BUG: unable to handle kernel paging request at ffffffffa001db38
[ 172.046020] IP: [<ffffffff81067aa4>] destroy_params+0x24/0x50
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Brian: tweaked a bit]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The old API expected a "partitions" property provided a phandle to a
separate partitions node, which itself contained yet more nodes each
representing one partition. The new API rids the requirement for the
superfluous intermediary partitions node. This patch provides the
added information required for automatic parsing by the core.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Until now the dynamically configurable message sequences for read, write
and enable 32bit addressing have been global. Brian makes a good point
why this should not be the case. If there are ever two FSM's located on
the same platform, we could be potentially introducing a race condition
on "needlessly shared data".
Suggested-by: Brian Norris <computersforpeace@gmail.com>
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch allows us to prepare some of the message sequences which will
be required to talk to the S25FLxxx family of Serial Flash devices. It
also allows us to do some required extra operations after any busy wait
failures.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When an erase is requested by userspace the MTD framework calls back
into the driver to conduct the actual command issue. Here we provide the
routines which do exactly that. We can choose to either do an entire chip
erase or by sector.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When we write data to the Serial Flash chip we'll wait a predetermined
period of time before giving up. During that period of time we poll the
status register until completion.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When we write data to the FIFO the FSM Controller subsequently writes
that data out to the Serial Flash chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When a read is issued by userspace the MTD framework calls back into
the driver to conduct the actual command issue and data extraction.
Here we provide the routines which do exactly that.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most chips require a predefined set of FSM message sequences for read,
write and erase operations. This patch provides a way to set them up,
which it will do so if a chip specific initialisation routine isn't
been provided.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In the FSM driver we handle chip differences by providing the possibility
of calling back into a chip specific initialisation routine. In this patch
we provide one for the N25Qxxx series, which endeavours to setup things
like the read, write and erase sequences, as they differ from the
default. We also configure 32bit support and the amount of dummy cycles to
use.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The N25Qxxx Serial Flash devices required different sequence
configurations depending on whether they're running in 24bit (3Byte)
or 32bit (4Byte) mode. We provide those here.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Message sequences can vary depending on how many pads (lines) are
required to address the chip (mode & dummy), how many data pads (lines)
are required to write out to the chip which will determine speed
amongst other things which are detailed by the SFDP specification. We
are able to use multiple configurations for each chip, but they need
to me matched to a device's capabilities. These configurations are
listed in preference order - most preferred first.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare the message sequence responsible for updating a chip's VCR.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most Serial Flash chips support 24bit addressing as a default but more
recent incarnations can support 32bit. Based on information provided
though platform specific data and capabilities we can determine whether
or not our current chip can. This patch provides a means to setup the
FSM message sequence to put the chip into 32bit mode.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Based on information we can obtain though platform specific data and/or
chip capabilities we are able to determine whether or not we can handle
a SoC reset or not. To find out why this is important please read the
comment provided in the patch.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Firstly we search for our preference read/write configuration based on a
given chip's capabilities. Then we actually set up the message sequence
accordingly.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare the message sequence responsible for setting 32bit addressing
mode on the Flash chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare the message sequence responsible for erasing a single sector.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's important for us to determine which device was used to boot from in
order to make some correct decisions surrounding Power Management. On
each of the platforms which support the FSM this is communicated via
a set of mode pins held in the system configuration area. This patch
determine the boot device and stores the result.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM Serial Flash Controller is driven by issuing a standard set of
register writes we call a message sequence. This patch supplies a method
to prepare read/write FSM message sequence(s) based on chip capability
and configuration.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Take some known parameters, namely size and number of sectors and use
them to determine weather a device can support 32bit addressing or not.
If it can, set the associated flash capability flag for latter use.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Here we provide a means to traverse though all supplied FSM message
sequence configurations and pick one based on our chip's capabilities.
The first one we match will be the preferred one, as they are
presented in order of preference.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using previously added infrastructure we can now extract a device's JEDEC
ID, compare it to a list of known and supported devices and make assumptions
based on known characteristics of a given chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Supply a lookup table of all the devices we intend to support. This table
is used to store device information such as; a human readable device name,
their JEDEC ID (plus the extended version), sector size and amount, a bit
store of a device's capabilities, its maximum running frequency and
possible use of a per-device configuration call-back.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
JEDEC have helped to standardise a great deal of the commands which
can be issued to a Serial Flash devices. Many of the Serial Flash
Discoverable Parameters (SFDP) commands are generic across devices.
This patch provides a shared point where these commands can be
defined.
Suggested-by: Mark Brown <broonie@kernel.org>
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Once we start supporting devices it will be handy go detect them
dynamically. This will be done using the chip's unique JEDEC ID. This
patch allows us to extract a device's JEDEC ID using the a predefined
FSM register write sequence.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When invoked the driver will attempt to read any available data from
the FSM's data register. Any data collected from this FIFO would have
originated from the flash chip.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The FSM hardware works by setting a predetermined sequence of register
writes. Rather than open coding them inside each functional block we're
going to define them in a series of formatted 'sequence structures'.
This patch provides the framework which shall be used for every action.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch uses default values to initialise a connected flash chip. This
includes; a device soft reset, setting of a safe working frequency, a
switch into Fast Sequencing Mode, configuring of timing data and a purge
of the FIFO.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Here we provide the FSM's register addresses, register bit names/offsets
and some commands which will prove useful as we start bulk the FMS's
driver out with functionality.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is a new driver. It's used to communicate with a special type of
optimised Serial Flash Controller called the FSM. The FSM uses a subset
of the SPI protocol to communicate with supported NOR-Flash devices.
Acked-by Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
'is_elm_present' flag is not used anywhere. This check is implicitely
taken care while selecting appropriate ecc-scheme via DT or board-file.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch
- refactors GPMC configurations based on ecc-scheme
- removed dependency on is_elm_present() flag, which is implicitely
taken care by selecting appropriate ecc-scheme
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Lots of if..then..else conditions in omap_enable_hwecc_bch() can be avoided if
code is refactored based on ecc-scheme.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch
- renames omap3_enable_hwecc_bch -> omap_enable_hwecc_bch to keep
nomenclature independent of any device family.
- using '__maybe_unused' instead of `ifdef based conditional compilation
to suppress warning for un-used functions
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
merge omap3_calculate_ecc_bch8() into omap_calculate_ecc_bch() so that
common callback can be used for both OMAP_ECC_BCH8_CODE_HW and
OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
+---------------------+-------------------------------------------------------+
|ecc-scheme | nand_chip->calculate() after this patch |
+---------------------+-------------------------------------------------------+
|HAM1_ECC | omap_calculate_ecc() |
+---------------------+-------------------------------------------------------+
|BCH4_HW_DETECTION_SW | omap_calculate_ecc_bch() |
|BCH4_HW | omap_calculate_ecc_bch() |
|BCH8_HW_DETECTION_SW | omap3_calculate_ecc_bch8() -> omap_calculate_ecc_bch()|
|BCH8_HW | omap_calculate_ecc_bch() |
+---------------------+-------------------------------------------------------+
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
merges omap3_calculate_ecc_bch4() into omap_calculate_ecc_bch() so that
common callback can be used for both OMAP_ECC_BCH4_CODE_HW and
OMAP_ECC_BCH4_CODE_HW_DETECTION_SW ecc-schemes
+---------------------+-------------------------------------------------------+
|ecc-scheme | nand_chip->calculate() after this patch |
+---------------------+-------------------------------------------------------+
|HAM1_ECC | omap_calculate_ecc() |
+---------------------+-------------------------------------------------------+
|BCH4_HW_DETECTION_SW | omap3_calculate_ecc_bch4() -> omap_calculate_ecc_bch()|
|BCH4_HW | omap_calculate_ecc_bch() |
|BCH8_HW_DETECTION_SW | omap3_calculate_ecc_bch8() |
|BCH8_HW | omap_calculate_ecc_bch() |
+---------------------+-------------------------------------------------------+
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
OMAP NAND driver supports multiple flavours of BCH4 and BCH8 ECC algorithms.
+------+------------------------------------+---------------+---------------+
| Algo | ECC scheme |ECC calculation|Error detection|
+------+------------------------------------+---------------+---------------+
| |OMAP_ECC_BCH4_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W |
| BCH4 |OMAP_ECC_BCH4_CODE_HW |H/W (GPMC) |H/W (ELM) |
+------+------------------------------------+---------------+---------------+
| |OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W |
| BCH8 |OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
+------+------------------------------------+---------------+---------------+
This patch refactors omap_calculate_ecc_bch() so that
- separate out ecc-scheme specific code so that common-code can be reused
between different implementations of same ECC algorithm.
- new ecc-schemes can be added with ease in future.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
rename omap3_calculate_ecc_bch -> omap_calculate_ecc_bch to
keep nomenclature independent of any device family.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch updates following checks when bit-flips are detected by ELM:
- Do not evaluate bit-flips when un-correctable bit-flips is reported by ELM,
because as per [1] when ELM reports an un-correctable bit-flips,
'number of error' field in its ELM_LOCATION_STATUS register is also invalid.
- Return with error-code '-EBADMSG' on detection of un-correctable bit-flip.
- Return with error-code '-EBADMSG' when bit-flips position is outside current
Sector and OOB area.
[1] ELM IP spec Table-25 ELM_LOCATION_STATUS Register.
ELM_LOCATION_STATUS[8] = ECC_CORRECTABLE: Error location process exit status
0x0: ECC error location process failed.
Number of errors and error locations are invalid.
0x1: all errors were successfully located.
Number of errors and error locations are valid.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current omap_elm_correct_data() code is not scalable for future ecc-schemes
due to presence of tweaks and hard-coded macros for BCH4_ECC and BCH8_ECC
ecc-schemes at multiple places.
This patch:
- replaces 'ecc_opt' with '(info->nand.ecc.strength == BCH8_MAX_ERROR)
used to differentiate between BCH8_HW and BCH4_SW
- replaces macros (defining magic number for specific ecc-scheme) with
generic variables
- removes dependency on macros defined in elm.h (like BCHx_ECC_OOB_BYTES)
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As erased-pages do not have ECC stored in their OOB area, so they need to be
seperated out from programmed-pages, before doing BCH ECC correction.
In current implementation of omap_elm_correct_data() which does ECC correction
for BCHx ECC schemes, this erased-pages are detected based on specific marker
byte (reserved as 0x00) in ecc-layout.
However, this approach has some limitation like;
1) All ecc-scheme layouts do not have such Reserved byte marker to
differentiate between erased-page v/s programmed-page. Thus this is a
customized solution.
2) Reserved marker byte can itself be subjected to bit-flips causing
erased-page to be misunderstood as programmed-page.
This patch removes dependency on any marker byte in ecc-layout, instead it
compares calc_ecc[] with pattern of ECC-of-all(0xff). This implicitely
means that both 'data + oob == all(0xff).
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
renaming following variables as they cause confusion due to resemblence to
another similar field in 'struct nand_ecc_ctrl' (nand_chip->ecc.size).
renaming: ecc_vector_size --> ecc->bytes (info->nand.ecc.bytes)
renaming: eccsize --> actual_eccbytes (info->nand.ecc.bytes - 1) for BCH4 and BCH8
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Information of currently selected ECC scheme 'enum omap_ecc ecc_opt' should
available outside platform-data, so that single nand_chip->ecc callback can
support multiple ecc-scheme configurations.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If a write to one time programmable memory (OTP) hits the end of this
memory area, no more data can be written. The count variable in
mtdchar_write() in drivers/mtd/mtdchar.c is not decreased anymore.
We are trapped in the loop forever, mtdchar_write() will never return
in this case.
The desired behavior of a write in such a case is described in [1]:
- Try to write as much data as possible, truncate the write to fit into
the available memory and return the number of bytes that actually
have been written.
- If no data could be written at all, return -ENOSPC.
This patch fixes the behavior of OTP write if there is not enough space
for all data:
1) mtd_write_user_prot_reg() in drivers/mtd/mtdcore.c is modified to
return -ENOSPC if no data could be written at all.
2) mtdchar_write() is modified to handle -ENOSPC correctly. Exit if a
write returned -ENOSPC and yield the correct return value, either
then number of bytes that could be written, or -ENOSPC, if no data
could be written at all.
Furthermore the patch harmonizes the behavior of the OTP memory write
in drivers/mtd/devices/mtd_dataflash.c with the other implementations
and the requirements from [1]. Instead of returning -EINVAL if the data
does not fit into the OTP memory, we try to write as much data as
possible/truncate the write.
[1] http://pubs.opengroup.org/onlinepubs/9699919799/functions/write.html
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
fixme applied : check device size is a multiple of erasesize.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Crash detected on sam5d35 and its pmecc nand ecc controller.
The problem was a call to chip->ecc.hwctl from nand_write_subpage_hwecc
(nand_base.c) when we write a sub page.
chip->ecc.hwctl function is not set when we are using PMECC controller.
As a workaround, set NAND_NO_SUBPAGE_WRITE for PMECC controller in
order to disable sub page access in nand_write_page.
Signed-off-by: Herve Codina <Herve.CODINA@celad.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
1) Why add the subpage read support?
The page size of the nand chip becomes larger and larger, the imx6 has to
supports the 16K page or even bigger page. But sometimes, the upper layer only
needs a small part of the page, such as 512 bytes or less.
For example, ubiattach may only read 64 bytes per page.
2) We only enable the subpage read support when it meets the conditions:
<1> the chip is imx6 (or later chips) which can supports large nand page.
<2> the size of ECC parity is byte aligned.
If the size of ECC parity is not byte aligned, the calling of NAND_CMD_RNDOUT
will fail.
3) What does this patch do?
This patch will fake a virtual small page for the subpage read, and call the
gpmi_ecc_read_page() to do the real work.
In order to fake a virtual small page, the patch changes the BCH registers and
the bch_geometry{}. After the subpage read finished, we will restore them back.
4) Performace:
4.1) Tested with Toshiba TC58NVG2S0F(4096 + 224) with the following command:
#ubiattach /dev/ubi_ctrl -m 4
The detail information of /dev/mtd4 shows below:
--------------------------------------------------------------
#mtdinfo /dev/mtd4
mtd4
Name: test
Type: nand
Eraseblock size: 262144 bytes, 256.0 KiB
Amount of eraseblocks: 1856 (486539264 bytes, 464.0 MiB)
Minimum input/output unit size: 4096 bytes
Sub-page size: 4096 bytes
OOB size: 224 bytes
Character device major/minor: 90:8
Bad blocks are allowed: true
Device is writable: true
--------------------------------------------------------------
4.2) Before this patch:
--------------------------------------------------------------
[ 94.530495] UBI: attaching mtd4 to ubi0
[ 98.928850] UBI: scanning is finished
[ 98.953594] UBI: attached mtd4 (name "test", size 464 MiB) to ubi0
[ 98.958562] UBI: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 98.964076] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 98.969518] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 98.975128] UBI: good PEBs: 1856, bad PEBs: 0, corrupted PEBs: 0
[ 98.979843] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 98.985878] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2024916145
[ 98.993635] UBI: available PEBs: 0, total reserved PEBs: 1856, PEBs reserved for bad PEB handling: 40
[ 99.001807] UBI: background thread "ubi_bgt0d" started, PID 831
--------------------------------------------------------------
The attach time is about 98.9 - 94.5 = 4.4s
4.3) After this patch:
--------------------------------------------------------------
[ 286.464906] UBI: attaching mtd4 to ubi0
[ 289.186129] UBI: scanning is finished
[ 289.211416] UBI: attached mtd4 (name "test", size 464 MiB) to ubi0
[ 289.216360] UBI: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
[ 289.221858] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 289.227293] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 289.232878] UBI: good PEBs: 1856, bad PEBs: 0, corrupted PEBs: 0
[ 289.237628] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
[ 289.243553] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 2024916145
[ 289.251348] UBI: available PEBs: 1812, total reserved PEBs: 44, PEBs reserved for bad PEB handling: 40
[ 289.259417] UBI: background thread "ubi_bgt0d" started, PID 847
--------------------------------------------------------------
The attach time is about 289.18 - 286.46 = 2.7s
4.4) The conclusion:
We achieve (4.4 - 2.7) / 4.4 = 38.6% faster in the ubiattach.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The nfc_geo->payload_size is equal to the mtd->writesize now,
use the nfc_geo->payload_size to replace the mtd->writesize.
This patch makes preparation for the gpmi's subpage read support.
In the subpage support, the nfc_geo->payload_size maybe smaller then
the mtd->writesize.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the "page" argument for the read_subpage hook. With this argument,
the implementation of this hook could prints out more accurate information
for debugging.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The nand_get_flash_type parameter "busw" input value is not used by any
branch, and it is updated before use it in the function, so remove it,
define the "busw" as an internal variable.
Signed-off-by: Cai Zhiyong <caizhiyong@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The actual ECC strength used to select the ECC scheme is 'ecc_strength'.
Use it in the error message.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This macro is not used so it's safe to remove it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Home routers based on SoCs like BCM53010 (AKA BCM4708) use flashes
which can be nicely partitioned with bcm47xxpart. Header bcm47xx_nvram.h
is not available on bcm53xx, so don't include it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Our code parsing "trx" header registers few partitions at once (in one
loop iteration). Add extra check in that place.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Up to now mtd-ram devices described in device trees were only accessible
if mtd-flash or mtd-rom were also configured at linux configuration
time, because MTD_PHYSMAP_OF was only available if (MTD_CFI ||
MTD_JEDECPROBE || MTD_ROM). Allow MTD_PHYSMAP_OF selection also
when only MTD_RAM is set.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no point in displaying the TS5500-specific driver entries if
TS5500 board support itself isn't enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Instead of writing to "nand->reg + REG_FMICSR" we write to "REG_FMICSR"
which is NULL and not a valid register.
Fixes: 8bff82cbc3 ('mtd: add nand support for w90p910 (v2)')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Check the chip->jedec_version, and print out the right information
for JEDEC compliant NAND.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds the parsing code for the JEDEC compliant NAND.
Since we need the 0x40 as the column address, this patch also
makes the NAND_CMD_PARAM to use the 8-bit address only.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Check the return value from platform_get_irq() and propagate it in the case of
error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
"rc" is an error code here, no need to check it a second time.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
PIO fall back is not an issue, so don't make this much noise.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ELM driver incorrectly reagard any non-zero return value from
pm_runtime_get_sync as an error, but it may return 1 if the device
was already active. Fix to only error when return value is negative.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
read_buf is called in place of write_buf in the
nand_write_page_raw_syndrome function.
Signed-off-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM and HAS_DMA to bypass build failures.
drivers/built-in.o: In function `flctl_probe':
drivers/mtd/nand/sh_flctl.c:1097: undefined reference to `devm_ioremap_resource'
drivers/built-in.o: In function `flctl_dma_fifo0_transfer':
drivers/mtd/nand/sh_flctl.c:368: undefined reference to `dma_map_single'
drivers/mtd/nand/sh_flctl.c:407: undefined reference to `dma_unmap_single'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use a repeated read_byte() instead of read_buf(), since for x16 buswidth
devices, we need to avoid the upper I/O[16:9] bits. See the following
commit for reference:
commit 05f7835975
Author: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Date: Thu Dec 5 22:22:04 2013 +0100
mtd: nand: don't use {read,write}_buf for 8-bit transfers
Now, I think that all barriers to probing ONFI on x16 devices are
removed, so remove the check from nand_flash_detect_onfi().
Tested on 8-bit ONFI NAND (Micron MT29F32G08CBADAWP).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-By: Pekon Gupta <pekon@ti.com>
The NAND command helpers tend to automatically shift the column address
for x16 bus devices, since most commands expect a word address, not a
byte address. The Read ID command, however, expects an 8-bit address
(i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
0x20).
This fixes the column address for a few drivers which imitate the
nand_base defaults. Note that I don't touch sh_flctl.c, since it already
handles this problem slightly differently (note its comment "READID is
always performed using an 8-bit bus").
I have not tested this patch, as I only have x8 parts up for testing at
this point. Hopefully that can change soon...
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-By: Pekon Gupta <pekon@ti.com>
The datasheet does not tell us how to parse out the ID data,
so handle it as a full ID nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The patch converts the arrays to buffer pointers for nand_buffers{}.
The cafe_nand.c is the only NAND_OWN_BUFFERS user which allocates
nand_buffers{} itself.
This patch disables the DMA for nand_scan_ident, and restores the DMA
status after we finish the nand_scan_ident. This way, we can get page
size and OOB size and use them to allocate cafe->dmabuf.
Since the cafe_nand.c uses the NAND_ECC_HW_SYNDROME ECC mode, we do not
allocate the buffers for @ecccalc and @ecccode.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[Brian: dropped one incorrect hunk]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mutex_destroy added on each device in block2mtd_exit and add_device failure
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit b2a2a84d35 (mtd: phram: dot not crash when
built-in and passing boot param) claims to be "based on Ville Herva's similar
patch to block2mtd" (c4e7fb3137), but it has
missed the crucial point of the original path: all these "if(n)def MODULE".
It has broken the possibility to create several phram instances when phram is
compiled as module. The possibility to add instances via /sys writes to
/sys/module/phram/parameters/phram was also broken with mentioned patch.
Proposed patch takes the idea of original block2mtd patch to its full extent.
Assumption "This function is always called before 'init_phram()'" was also
incorrect, so removed the comment. This patch effectively reverts also
b11ec57fc6 (mtd: phram: fix section mismatch for
phram_setup).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
[Brian: remove static assigment = 0]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We always put a NUL terminator one space past the end of the "vendor"
buffer. Walter Harms also pointed out that this should just use
kstrndup().
Fixes: 7d17c02a01 ('mtd: Add new SmartMedia/xD FTL')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Spansion s25fl256s1 and s25fl512s support Dual SPI transfers, hence set the
M25P80_DUAL_READ flag.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for Dual SPI read transfers, which is supported by some
Spansion SPI FLASHes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Rename the UBI_IOCVOLATTBLK and UBI_IOCVOLDETBLK to UBI_IOCVOLCRBLK and
UBI_IOCVOLRMBLK, because we do not use terms "attach" and "detach" for the R/O
block devices on top of UBI volumes. Instead, we use terms "create" and
"remove". This patch also amends the related commentaries.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
In order to have a way of distinguishing an invalid ioctl from a
not supported (but otherwise valid) ioctl, this commit changes the
return value of the ioctl stubs from ENOTTY to ENOSYS.
This will be useful to report more accurate error messages from
userspace tools.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The UBI block driver depends on the block infrastructure. Add the
proper dependency and fix a build error when CONFIG_BLOCK is not selected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Fixes the following warning on ARCH=avr32:
drivers/mtd/ubi/block.c: In function 'ubiblock_read':
drivers/mtd/ubi/block.c:207: warning: comparison of distinct pointer types lacks a cast
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
ubiblock_param_ops should be marked as __init as it's only used to set
a driver parameter on insertion time. This commit fixes the following:
WARNING: drivers/mtd/built-in.o(.text+0x653ac): Section mismatch in
reference from the variable ubiblock_param_ops to the function
.init.text:ubiblock_set_param()
The function ubiblock_param_ops() references the function __init
ubiblock_set_param(). This is often because ubiblock_param_ops lacks a
__init annotation or the annotation of ubiblock_set_param is wrong.
Given gcc errors if the struct is marked const __initdata, this commit
drops the const mark from it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We already use term attach/detach for UBI->MTD relations, let's not use this
for UBI->ubiblock relations to avoid confusion. Just use 'create' and 'remove'
instead. E.g., "create a R/O block device on top of a UBI volume".
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
commit d2ae2e20fb ("driver/memory:Move
Freescale IFC driver to a common driver") introduces this build
regression into the mpc85xx_defconfig:
drivers/built-in.o: In function `fsl_ifc_nand_remove':
drivers/mtd/nand/fsl_ifc_nand.c:1147: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1147: undefined reference to `fsl_ifc_ctrl_dev'
drivers/built-in.o: In function `fsl_ifc_nand_probe':
drivers/mtd/nand/fsl_ifc_nand.c:1031: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1031: undefined reference to `fsl_ifc_ctrl_dev'
drivers/built-in.o: In function `match_bank':
drivers/mtd/nand/fsl_ifc_nand.c:1013: undefined reference to `convert_ifc_address'
drivers/built-in.o: In function `fsl_ifc_nand_probe':
drivers/mtd/nand/fsl_ifc_nand.c:1059: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1080: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1069: undefined reference to `fsl_ifc_ctrl_dev'
drivers/mtd/nand/fsl_ifc_nand.c:1069: undefined reference to `fsl_ifc_ctrl_dev'
make: *** [vmlinux] Error 1
This happens because there is nothing to descend us into the
drivers/memory directory in the mpc85xx_defconfig. It wasn't
selecting CONFIG_MEMORY. So we never built drivers/memory/fsl_ifc.o
and so we have nothing to link the above symbols against.
Since the goal of the original commit was to relocate the driver to
an arch independent location, it only makes sense to relocate the
Kconfig setting there as well. But that alone won't fix the build
failure; for that we ensure whoever selects FSL_IFC also selects MEMORY.
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit introduces read-only block device emulation on top of UBI volumes.
Given UBI takes care of wear leveling and bad block management it's possible
to add a thin layer to enable block device access to UBI volumes.
This allows to use a block-oriented filesystem on a flash device.
The UBI block devices are meant to be used in conjunction with any
regular, block-oriented file system (e.g. ext4), although it's primarily
targeted at read-only file systems, such as squashfs.
Block devices are created upon user request through new ioctls:
UBI_IOCVOLATTBLK to attach and UBI_IOCVOLDETBLK to detach.
Also, a new UBI module parameter is added 'ubi.block'. This parameter is
needed in order to attach a block device on boot-up time, allowing to
mount the rootfs on a ubiblock device.
For instance, you could have these kernel parameters:
ubi.mtd=5 ubi.block=0,0 root=/dev/ubiblock0_0
Or, if you compile ubi as a module:
$ modprobe ubi mtd=/dev/mtd5 block=/dev/ubi0_0
Artem: amend commentaries and massage the patch a little bit.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
touch freed memory.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J2Up
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.14-rc5' of git://git.infradead.org/linux-ubifs
Pull ubifs fix from Artem Bityutskiy:
"Just a single fix for the UBI module unload path which makes sure we
do not touch freed memory"
* tag 'upstream-3.14-rc5' of git://git.infradead.org/linux-ubifs:
UBI: fix some use after free bugs
This patch excludes reserved-marker byte-position from oobfree->length
calculation. Thus all bytes from oobfree->offset till end of OOB are free.
CC: <stable@vger.kernel.org> # 3.13.x+
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
1) In current implementation, ecclayout->oobfree->offset is calculated with
respect to ecclayout->eccpos[0] which is incorrect because ECC bytes may not
be stored contiguously in OOB.
So, this patch calculates ecclayout->oobfree->offset with respect to last
ECC byte-position 'eccpos[ecclayout->eccbytes-1]'.
2) ECC layout of some ecc-schemes expects reserved-markers at specific eccpos[]
which should not be over-written by any file-system metadata.
So this patch aligns oobfree->offset taking into account of such markers.
CC: <stable@vger.kernel.org> # 3.13.x+
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The problem that the set timings code contains the call of Davinci
platform function davinci_aemif_setup_timing() which is not
accessible if kernel is built for another platform like Keystone.
The Keysone platform is going to use TI AEMIF driver.
If TI AEMIF is used we don't need to set timings and bus width.
It is done by AEMIF driver.
To get rid of davinci-nand driver dependency on aemif platform code
we moved aemif code to davinci platform.
The platform AEMIF code (aemif.c) has to be removed once Davinci
will be converted to DT and use ti-aemif.c driver.
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[nsekhar@ti.com: fixed checkpatch error and a build breakage due to
missing include, rebased onto l2-mtd/master]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/memory
and fix the header file includes.
Also remove module_platform_driver() and instead call
platform_driver_register() from subsys_initcall() to make sure this module
has been loaded before MTD partition parsing starts.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename symbols, variables, functions and structure fields related do
the resume latency device PM QoS type so that it is clear where they
belong (in particular, to avoid confusion with the latency tolerance
device PM QoS type introduced by a subsequent changeset).
Update the PM QoS documentation to better reflect its current state.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move the kmem_cache_free() calls down a couple lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
possible, because the eraseblock may be in an "unstable" state and write
operation sometimes causes NOR chip lock-ups.
* Both UBI and UBIFS changes are now maintainer in one single tree, because the
amount of changes dropped significantly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=pRDO
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.14-rc1' of git://git.infradead.org/linux-ubifs
Pull ubifs updates from Artem Bityutskiy:
- Improve the NOR erasure quirk - now it tries to do as little writes
as possible, because the eraseblock may be in an "unstable" state and
write operation sometimes causes NOR chip lock-ups.
- Both UBI and UBIFS changes are now maintainer in one single tree,
because the amount of changes dropped significantly.
* tag 'upstream-3.14-rc1' of git://git.infradead.org/linux-ubifs:
UBI: avoid program operation on NOR flash after erasure interrupted
MAINTAINERS: keep UBI and UBIFS stuff in the same tree
UBI: fix error return code
Pull more powerpc bits from Ben Herrenschmidt:
"Here are a few more powerpc bits for this merge window. The bulk is
made of two pull requests from Scott and Anatolij that I had missed
previously (they arrived while I was away). Since both their branches
are in -next independently, and the content has been around for a
little while, they can still go in.
The rest is mostly bug and regression fixes, a small series of
cleanups to our pseries cpuidle code (including moving it to the right
place), and one new cpuidle bakend for the powernv platform. I also
wired up the new sched_attr syscalls"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (37 commits)
powerpc: Wire up sched_setattr and sched_getattr syscalls
powerpc/hugetlb: Replace __get_cpu_var with get_cpu_var
powerpc: Make sure "cache" directory is removed when offlining cpu
powerpc/mm: Fix mmap errno when MAP_FIXED is set and mapping exceeds the allowed address space
powerpc/powernv/cpuidle: Back-end cpuidle driver for powernv platform.
powerpc/pseries/cpuidle: smt-snooze-delay cleanup.
powerpc/pseries/cpuidle: Remove MAX_IDLE_STATE macro.
powerpc/pseries/cpuidle: Make cpuidle-pseries backend driver a non-module.
powerpc/pseries/cpuidle: Use cpuidle_register() for initialisation.
powerpc/pseries/cpuidle: Move processor_idle.c to drivers/cpuidle.
powerpc: Fix 32-bit frames for signals delivered when transactional
powerpc/iommu: Fix initialisation of DART iommu table
powerpc/numa: Fix decimal permissions
powerpc/mm: Fix compile error of pgtable-ppc64.h
powerpc: Fix hw breakpoints on !HAVE_HW_BREAKPOINT configurations
clk: corenet: Adds the clock binding
powerpc/booke64: Guard e6500 tlb handler with CONFIG_PPC_FSL_BOOK3E
powerpc/512x: dts: add MPC5125 clock specs
powerpc/512x: clk: support MPC5121/5123/5125 SoC variants
powerpc/512x: clk: enforce even SDHC divider values
...
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
- Add me (Brian Norris) as an additional MTD maintainer (it'd be nice to get
David's "ack" for this; I'm sure he approves, but he's been pretty silent
lately)
- Add Ezequiel Garcie as maintainer for the pxa3xx NAND driver
- Last (?) round of pxa3xx improvements for supporting Armada 370/XP
- Typical churn in driver boilerplate (OOM messages, printk()'s, devm_*, etc.)
- Quad read mode support for SPI NOR driver (m25p80)
- Update Davinci NAND driver to prepare for use on new platforms
- Begin to kill off NAND_MAX_{PAGE,OOB}SIZE macros; more work is pending
- Miscellaneous NAND device support (new IDs)
- Add READ RETRY support for Micron MLC NAND
- Support new GPMI NAND ECC layout device-tree binding
- Avoid mapping stack/vmalloc() memory for GPMI NAND DMA
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=3nT9
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140127' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
- Add me (Brian Norris) as an additional MTD maintainer (it'd be nice to get
David's "ack" for this; I'm sure he approves, but he's been pretty silent
lately)
- Add Ezequiel Garcie as maintainer for the pxa3xx NAND driver
- Last (?) round of pxa3xx improvements for supporting Armada 370/XP
- Typical churn in driver boilerplate (OOM messages, printk()'s, devm_*, etc.)
- Quad read mode support for SPI NOR driver (m25p80)
- Update Davinci NAND driver to prepare for use on new platforms
- Begin to kill off NAND_MAX_{PAGE,OOB}SIZE macros; more work is pending
- Miscellaneous NAND device support (new IDs)
- Add READ RETRY support for Micron MLC NAND
- Support new GPMI NAND ECC layout device-tree binding
- Avoid mapping stack/vmalloc() memory for GPMI NAND DMA
* tag 'for-linus-20140127' of git://git.infradead.org/linux-mtd: (151 commits)
mtd: gpmi: add sanity check when mapping DMA for read_buf/write_buf
mtd: gpmi: allocate a proper buffer for non ECC read/write
mtd: m25p80: Set rx_nbits for Quad SPI transfers
mtd: m25p80: Enable Quad SPI read transfers for s25fl512s
mtd: s3c2410: Merge plat/regs-nand.h into s3c2410.c
mtd: mtdram: add missing 'const'
mtd: m25p80: assign default read command
mtd: nuc900_nand: remove redundant return value check of platform_get_resource()
mtd: plat_nand: remove redundant return value check of platform_get_resource()
mtd: nand: add Intel manufacturer ID
mtd: nand: add SanDisk manufacturer ID
mtd: nand: add support for Samsung K9LCG08U0B
mtd: nand: pxa3xx: Add support for 2048 bytes page size devices
mtd: m25p80: Use OPCODE_QUAD_READ_4B for 4-byte addressing
mtd: nand: don't use {read,write}_buf for 8-bit transfers
mtd: nand: use __packed shorthand
mtd: nand: support Micron READ RETRY
mtd: nand: add generic READ RETRY support
mtd: nand: add ONFI vendor block for Micron
mtd: nand: localize ECC failures per page
...
The buffer pointer passed from the upper layer may points to
a buffer in the stack or a buffer allocated by vmalloc, and etc..
This patch adds more sanity check to this buffer.
After this patch, if we meet a buffer which is allocated by vmalloc or
a buffer in the stack, we will use our own DMA buffer @data_buffer_dma
to do the DMA operations. If the buffer is not the cases above, we will
map it for DMA operations directly.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The @data_buffer_dma buffer is used for non ECC read/write.
Currently, the length of the buffer is PAGE_SIZE, but the NAND chip may
has 8K page or 16K page. So we have to extend it for the large page NAND
chips.
The gpmi_alloc_dma_buffer will be called twice. The first time is to
allocate a temporary buffer for scanning the NAND chip; The second time
is to allocate a buffer to store the real page content.
This patch allocates a buffer of PAGE_SIZE size for scanning the NAND
chip when gpmi_alloc_dma_buffer is called the first time, and allocates a
buffer of the real NAND page size for the second time gpmi_alloc_dma_buffer
is called.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When using the Quad Read opcode, SPI masters still use Single SPI
transfers, as spi_transfer.rx_nbits defaults to SPI_NBITS_SINGLE.
Use SPI_NBITS_QUAD to fix this.
While an earlier version of commit 3487a63955
("drivers: mtd: m25p80: add quad read support") did this correctly, it was
forgotten in the version that got merged.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
plat/regs-nand.h is used only by S3C2410 nand driver. Since there
are no other users, merge this file into the driver code to remove
platform dependency. While at it also remove unused macros.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtdram_init_device() wasn't updated along with mtd_partition.name.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
In the following commit (in -next):
commit 8552b439ab
drivers: mtd: m25p80: convert "bool" read check into an enum
We converted the boolean 'fast_read' property to become an enum
'flash_read', but at the same time, we changed the conditional path so
that it doesn't choose a default value in some cases (technically, we
choose the correct default simply by virtue of devm_kzalloc(), which
zeroes this out to be a NORMAL read operation, but still...).
Fix this by setting a default for the 'else' clause.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource(). And move those two call together
to make the connection between them more clear.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the Intel manufacturer Id.
Tested with Intel JS29F32G08ACMD1(4096 + 224) which is ONFI 2.0 compliant
nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the manufactor ID for SanDisk.
Make preparation for SanDisk SDTNRGAMA-008G.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Assume that:
tmp = ((extid >> 2) & 0x04) | (extid & 0x03));
From the K9LCG08U0B's datasheet, we know that:
the oob size is 640 when tmp is 6;
the oob size is 1024 when tmp is 7;
Signed-off-by: Huang Shijie <b32955@freescale.com>
[Brian: fixed compile issue]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds support for devices with 2048B page sizes and
4-bit ECC strength requirements. This is achieved by enabling the BCH
ECC engine, which provides a higher strength: 16-bit over 2048 bytes.
Additionally, add a proper ECC layout to model the controller's view
of the device (where 'U' means unused and 'B' is the bad block marker):
----------------------------------------------------
| 2048B data | B | B | 30B spare | 30B ECC | U | U |
----------------------------------------------------
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
[Brian: updated with Ezequiel's patch description]
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
commit 3487a63955 ("drivers: mtd: m25p80: add
quad read support") in -next added both the 3-byte OPCODE_QUAD_READ and the
4-byte OPCODE_QUAD_READ_4B, but incorrectly uses OPCODE_QUAD_READ for both
3-byte and 4-byte addressing.
Use OPCODE_QUAD_READ_4B in the 4-byte case to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
According to the Open NAND Flash Interface Specification (ONFI) Revision
3.1 "Parameters are always transferred on the lower 8-bits of the data
bus." for the Get Features and Set Features commands.
So using read_buf and write_buf is wrong for 16-bit wide nand chips as
they use I/O[15:0]. The Get Features command is easily fixed using 4
times the read_byte callback. For Set Features implement a new
overwritable callback "write_byte". Still I expect the default to work
just fine for all controllers and making it overwriteable was just done
for symmetry.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[Brian: fixed warning]
Tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Micron provides READ RETRY support via the ONFI vendor-specific
parameter block (to indicate how many read-retry modes are available)
and the ONFI {GET,SET}_FEATURES commands with a vendor-specific feature
address (to support reading/switching the current read-retry mode).
The recommended sequence is as follows:
1. Perform PAGE_READ operation
2. If no ECC error, we are done
3. Run SET_FEATURES with feature address 89h, mode 1
4. Retry PAGE_READ operation
5. If ECC error and there are remaining supported modes, increment the
mode and return to step 3. Otherwise, this is a true ECC error.
6. Run SET_FEATURES with feature address 89h, mode 0, to return to the
default state.
This patch implements the chip->setup_read_retry() callback for
Micron and fills in the chip->read_retries.
Tested on Micron MT29F32G08CBADA, which supports 8 read-retry modes.
The Micron vendor-specific table was checked against the datasheets for
the following Micron NAND:
Needs retry Cell-type Part number Vendor revision Byte 180
----------- --------- ---------------- --------------- ------------
No SLC MT29F16G08ABABA 1 Reserved (0)
No MLC MT29F32G08CBABA 1 Reserved (0)
No SLC MT29F1G08AACWP 1 0
Yes MLC MT29F32G08CBADA 1 08h
Yes MLC MT29F64G08CBABA 2 08h
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Modern MLC (and even SLC?) NAND can experience a large number of
bitflips (beyond the recommended correctability capacity) due to drifts
in the voltage threshold (Vt). These bitflips can cause ECC errors to
occur well within the expected lifetime of the flash. To account for
this, some manufacturers provide a mechanism for shifting the Vt
threshold after a corrupted read.
The generic pattern seems to be that a particular flash has N read retry
modes (where N = 0, traditionally), and after an ECC failure, the host
should reconfigure the flash to use the next available mode, then retry
the read operation. This process repeats until all bitfips can be
corrected or until the host has tried all available retry modes.
This patch adds the infrastructure support for a
vendor-specific/flash-specific callback, used for setting the read-retry
mode (i.e., voltage threshold).
For now, this patch always returns the flash to mode 0 (the default
mode) after a successful read-retry, according to the flowchart found in
Micron's datasheets. This may need to change in the future if it is
determined that eventually, mode 0 is insufficient for the majority of
the flash cells (and so for performance reasons, we should leave the
flash in mode 1, 2, etc.).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
ECC failures can be tracked at the page level, not the do_read_ops level
(i.e., a potentially multi-page transaction).
This helps prepare for READ RETRY support.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Now that the driver can support the Armada 370/XP SoC NAND controller,
add the devicetree compatible string, enabling its use.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
after device tree based clock lookup became available, the NAND
flash driver need no longer use the previous global "nfc_clk" name,
but should use the "ipg" clock name specific to the OF node
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch kills the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZE by the following
way:
1.) change the @buf field of nand_buf{} from an array to a pointer.
also remove the DENALI_BUF_SIZE macro.
2.) Before we call the nand_scan_ident, we allocate a temporary buffer
whose size is PAGE_SIZE.
3.) After we finish the nand_scan_ident, we have already getten the
page size and oob size. We will allocate the right buffer size
again.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We kill the NAND_MAX_PAGESIZE/NAND_MAX_OOBSIZE by the following way:
1.) Before we call the nand_scan_ident, we allocate a temporary buffer
whose size is PAGE_SIZE.
2.) After we finish the nand_scan_ident, we have already getten the
page size and oob size. We will allocate the right buffer size
again.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
mtd.name is assigned to IFC NAND physical address. Assignment type is u32.
It is not providing correct physical address of IFC NAND.
Update assignment type to u64.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch assigned the type->name to mtd->name when mtd->name is
NULL in function "find_full_id_nand".
mtd->name is NULL may cause some problem.
Signed-off-by: Cai Zhiyong <caizhiyong@huawei.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
commit 93115b7fa8 ("mtd: onenand/samsung: make regs-onenand.h file local")
moved the file to the current location but forgot to remove the pointer to
its previous location. Clean it up.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The kernel already has this information, and individual drivers
shouldn't duplicate that. This also eliminates the use of __DATE__ and
__TIME__, which make the build non-deterministic.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nor_erase_prepare() will be called before erase a NOR flash, it will program '0'
into a block to mark this block. But program data into a erasure interrupted block
can cause program timtout(several minutes at most) error, could impact other
operation on NOR flash. So UBIFS can read this block first to avoid unneeded
program operation.
This patch try to put read operation at head of write operation in
nor_erase_prepare(), read out the data.
If the data is already corrupt, then no need to program any data into this block,
just go to erase this block.
This patch is validated on Micron NOR flash, part number is：JS28F512M29EWHA
Signed-off-by: Qi Wang <qiwang@micron.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some devices (like WNDR3700v3) have board_data without MPFR magic, some
extra header or extra NVRAM around 0x100. In such case we have to look
for another magic which is BD 0B 0D BD (BD probably stands for Board
Data). It's located "far far away", so instead of extending buffer add
another mtd_read.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some devices have even nicer-to-recognize CFE thanks to the magic.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Make this option a hidden one and get a cleaner configuration.
This option just selects a common infrastructure for MTD-based devices
to expose a block interface. There is no point in allowing a separate
enable/disable.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
[Brian: keep symbol as tristate]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fixes this sparse warning:
CHECK drivers/mtd/onenand/generic.c
drivers/mtd/onenand/generic.c:61:62: warning: Using plain integer as NULL pointer
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The omap_{read,write}_buf{8,16}() functions are identical to the default
nand_base versions. Just let nand_base assign them in the
NAND_OMAP_POLLED case.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Pekon Gupta <pekon@ti.com>
We shouldn't try to allocate a resource until we're sure the
of_property_read_u64() call didn't fail. This is especially important if
we use this code for both CONFIG_OF and !CONFIG_OF builds, since
of_property_read_u64() will always return -ENOSYS for !CONFIG_OF.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_warn() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull ARM fixes from Russell King:
"Another set of small fixes for ARM, covering various areas.
Laura fixed a long standing issue with virt_addr_valid() failing to
handle holes in memory. Steve found a problem with dcache flushing
for compound pages. I fixed another bug in footbridge stuff causing
time to tick slowly, and also a problem with the AES code which can
cause linker errors.
A patch from Rob which fixes Xen problems induced by a lack of
consistency in our naming of ioremap_cache() - which thankfully has
very few users"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 7933/1: rename ioremap_cached to ioremap_cache
ARM: fix "bad mode in ... handler" message for undefined instructions
CRYPTO: Fix more AES build errors
ARM: 7931/1: Correct virt_addr_valid
ARM: 7923/1: mm: fix dcache flush logic for compound high pages
ARM: fix footbridge clockevent device
ioremap_cache is more aligned with other architectures.
There are only 2 users of this in the kernel: pxa2xx-flash and Xen.
This fixes Xen build failures on arm64:
drivers/tty/hvc/hvc_xen.c:233:2: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/grant-table.c:1174:3: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
drivers/xen/xenbus/xenbus_probe.c:778:4: error: implicit declaration of function 'ioremap_cached' [-Werror=implicit-function-declaration]
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_kzalloc() to make cleanup paths simpler. Also, checking
return value of devm_kzalloc() is added in order to check if the
allocation succeded.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In order to avoid code duplication, let's consolidate the ECC setting
for all SoC variants. Such decision is based on page size and ECC
strength requirements.
Also, provide a default value for the case where such ECC information
is not provided (non-ONFI devices).
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently, we have two different cmdfunc's implementations:
one for PXA3xx SoC variant and one for Armada 370/XP SoC variant.
The former is the legacy one, typically constrained to devices
with page sizes smaller or equal to the controller's FIFO buffer.
On the other side, the latter _only_ supports the so-called extended
command semantics, which allow to handle devices with larger
page sizes (4 KiB, 8 KiB, ...).
This means we currently don't support devices with smaller pages on the
A370/XP SoC. Fix it by first renaming the cmdfuncs variants, and then
make the choice based on device page size (and SoC variant), rather than
SoC variant alone.
While at it, add a check for page size, to make sure we don't allow larger
pages sizes on the PXA3xx variant.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently the driver assumes all commands will eventually trigger a RnB
transition, and thus a "device is ready" IRQ.
This assumption means that on every issued command, the dev_ready completion
handler is init'ed and the need_wait flag is set.
However this is incorrect: some commands (such as NAND_CMD_STATUS) don't
make the device 'busy' and thus a RnB transition never occurs.
Given, the NAND core never calls waitfunc() after such commands, this
is not a problem.
Therefore, it's possible to only clear the need_wait flag on every command
that is started.
This fixes a current bug that can be reproduced on PXA boards by writing
blank (all 0xff'ed) to a page:
1. The kernel issues NAND_CMD_STATUS and sets need_wait=1. The flag
won't be cleared for this command since no RnB transition is
involved.
2. NAND_CMD_PAGEPROG is issued but since the data is blank, the driver
decides not to execute the command (and no IRQ activity is
involved).
3. The NAND core calls waitfunc() and waits for the dev_ready
completion, which will never end since the device _is_ already ready.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch marks the function is_erased() as static in denali.c because
it is not used outside this file.
This patch elimiates the following warning in nand/denali.c:
drivers/mtd/nand/denali.c:900:6: warning: no previous prototype for ‘is_erased’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch marks the functions do_write_buffer() and do_erase_oneblock()
as static because because they are not used outside this file. It also
removes the unused function word_program() in lpddr/lpddr_cmds.c.
Thus, it also removes the following warnings in lpddr/lpddr_cmds.c:
drivers/mtd/lpddr/lpddr_cmds.c:391:5: warning: no previous prototype for ‘do_write_buffer’ [-Wmissing-prototypes]
drivers/mtd/lpddr/lpddr_cmds.c:472:5: warning: no previous prototype for ‘do_erase_oneblock’ [-Wmissing-prototypes]
drivers/mtd/lpddr/lpddr_cmds.c:751:5: warning: no previous prototype for ‘word_program’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver doesn't need its own custom chip->write_page callback; the
only "custom" requirement is that this driver does not support subpage
writes, which we can avoid using the NAND_NO_SUBPAGE_WRITE flag. With
NAND_NO_SUBPAGE_WRITE, the default routine (nand_write_page()) should
perform the equivalent operations.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Tested-by: Roland Stigge <stigge@antcom.de>
The TI AEMIF driver registers are used to setup timings for each chip
select. The same registers range is used to setup NAND settings.
The AEMIF and NAND drivers not use the same registers in this range.
In case with TI AEMIF driver, the memory address range is requested
already by AEMIF, so we cannot request it twice, just ioremap.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Keystone arch has compatible nand device, so reuse it.
In case with Keystone it depends on TI_AEMIF because AEMIF
driver is responsible to set timings.
See http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The properties davinci-ecc-mode, davinci-nand-use-bbt, davinci-nand-buswidth
are MTD generic. Correct names for them are: nand-ecc-mode, nand-on-flash-bbt,
nand-bus-width accordingly. So rename them in dts and documentation.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is not needed to use a lot of names for err handling.
It complicates code support and reading.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The property "ti,davinci-chipselect" is required. So we have to check
if it is set.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case when memory allocation is failed the driver should return
ENOMEM instead of ENODEV.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When kernel is booted using DT, there is no guarantee that Davinci
NAND device has been created already at the time when driver init
function is executed. Therefore, platform_driver_probe() can't be used
because this may result the Davinci NAND driver will never be probed.
The driver probing has to be made with core mechanism.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
clock source is prepared and enabled by clk_prepare_enable() in
mxcnd_probe() function, but no disable/unprepare in mxcnd_remove().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the of_mtd header provides dummy stubs for !CONFIG_OF, it's safe
to remove the #ifdef CONFIG_OF. Build tested only.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cast pointers to uintptr_t instead of unsigned int. This fixes warnings
on platforms where pointers have a different size than int.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
register_mtd_parser never fails; hence make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
deregister_mtd_parser never fails; hence make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a nice "nand:" prefix to all pr_xxx() messages. This allows
to get rid of the "NAND" words in messages, given the context
is already given by the prefix.
Remove the __func__ report from messages where it's not needed and refactor
the device detection messages to show itself in several lines.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using the IS_ENABLED() macro can make the code shorter and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use new ATTRIBUTE_GROUPS macro to declare attribute groups.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for Micron m25px16 spi flash chip.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ecc_stats.corrected count variable will already be incremented in
the above framework-layer just after this callback.
Cc: stable@vger.kernel.org # 2.6.36+
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The devm_request_irq function allocates irq that is released
when a driver detaches. Thus, there is no reason to explicitly
call devm_free_irq in probe or remove functions.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There are pr_err and dev_err in the gpmi driver now.
It makes people confused.
This patch changes all the pr_err to dev_err except the one
in the gpmi_reset_block(). We also remove the unnecessary
print for OOM message.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The error messages for the failure of dmaengine_prep_slave_sg are
not necessary, this patch removes all these pr_err, and returns with
the proper error code -EINVAL, not -1.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
