eventual replacement for ->get_sb() - does *not* get vfsmount,
return ERR_PTR(error) or root of subtree to be mounted.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
and branch 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm
* 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: register xen pci notifier
xen: initialize cpu masks for pv guests in xen_smp_init
xen: add a missing #include to arch/x86/pci/xen.c
xen: mask the MTRR feature from the cpuid
xen: make hvc_xen console work for dom0.
xen: add the direct mapping area for ISA bus access
xen: Initialize xenbus for dom0.
xen: use vcpu_ops to setup cpu masks
xen: map a dummy page for local apic and ioapic in xen_set_fixmap
xen: remap MSIs into pirqs when running as initial domain
xen: remap GSIs as pirqs when running as initial domain
xen: introduce XEN_DOM0 as a silent option
xen: map MSIs into pirqs
xen: support GSI -> pirq remapping in PV on HVM guests
xen: add xen hvm acpi_register_gsi variant
acpi: use indirect call to register gsi in different modes
xen: implement xen_hvm_register_pirq
xen: get the maximum number of pirqs from xen
xen: support pirq != irq
* 'stable/xen-pcifront-0.8.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (27 commits)
X86/PCI: Remove the dependency on isapnp_disable.
xen: Update Makefile with CONFIG_BLOCK dependency for biomerge.c
MAINTAINERS: Add myself to the Xen Hypervisor Interface and remove Chris Wright.
x86: xen: Sanitse irq handling (part two)
swiotlb-xen: On x86-32 builts, select SWIOTLB instead of depending on it.
MAINTAINERS: Add myself for Xen PCI and Xen SWIOTLB maintainer.
xen/pci: Request ACS when Xen-SWIOTLB is activated.
xen-pcifront: Xen PCI frontend driver.
xenbus: prevent warnings on unhandled enumeration values
xenbus: Xen paravirtualised PCI hotplug support.
xen/x86/PCI: Add support for the Xen PCI subsystem
x86: Introduce x86_msi_ops
msi: Introduce default_[teardown|setup]_msi_irqs with fallback.
x86/PCI: Export pci_walk_bus function.
x86/PCI: make sure _PAGE_IOMAP it set on pci mappings
x86/PCI: Clean up pci_cache_line_size
xen: fix shared irq device passthrough
xen: Provide a variant of xen_poll_irq with timeout.
xen: Find an unbound irq number in reverse order (high to low).
xen: statically initialize cpu_evtchn_mask_p
...
Fix up trivial conflicts in drivers/pci/Makefile
In preparation for the addition of SPI support for the WM831x move the I2C
specific code into a separate file with a separate Kconfig option so the
I2C support can be excluded from the build.
Also update the 1133-EV1 PMIC module support for SMDK6410 to use the new
symbol.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
BUCK1/2 internal voltages and indexes defined in the struct max8998_data
max_get_voltage_register now uses index values to chose proper register
More generic BUCK1/2 registers names provided
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
mc13892 is the companion PMIC for Freescale's i.MX51. It's similar enough
to mc13782 to support it in a single driver.
This patch introduces enough compatibility cruft to keep all users of the
superseded mc13783 driver unchanged.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The last user is gone since v2.6.34-rc1~40
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming VIA VX855 MFD driver needs to communicate resources
to subdevices where the resources may be claimed by ACPI.
Add a flag to mfd_cell to request that resources are not policed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Otherwise sparse warns about a public symbol with no declaration and
the compiler can't spot if the callers and users have different signatures
for the function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for enabling and disabling tps6586x subdevice interrupts
Signed-off-by: Gary King <gking@nvidia.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch makes the ab8500 mixed signal chip expose the same
interface for register access as the ab3100, ab3550 and ab5500 chip.
The ab8500_read() and ab8500_write() is removed and replaced with
abx500_get_register_interruptible() and
abx500_set_register_interruptible().
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit
mode if the hardware supports it.
Tested with the SDHI hardware block included in sh7724.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Magnus Damm <damm@opensource.se>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sh_mmcif controller, so that polling needs
to be used. To overcome the overhead induced by querying the controller
on each poll cycle, card detection can be handled in the platform code
more efficiently.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sdhi hardware, so that polling needs to be used
with tmio_mmc and card detection is handled in the platform code.
This patch allows to set tmio_mmc capabilities (to pass the
MMC_CAP_NEEDS_POLL flag) and exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some controllers, supported by the tmio_mmc driver do not have the card
detect pin of a slot connected, so that polling needs to be used and
card detection is handled by other means.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the RTC provided by the Maxim 8998 chip. This
driver was tested on a GONI board by using the rtc-test application from
the Documentation/rtc.txt.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use genirq and provide seperated file for interrupts support.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8998 chip have regulator and rtc features. The i2c slave address
of regulator and rtc is different, so needs each i2c client on i2c
operation functions.
Also, this patch exports i2c operation functions instead of callback to
make easy to read.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some modules already need to talk to at least PROTECT_KEY
register, while at that, add defines to the entire register
space.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixed warnings about unprototyped global functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
initramfs: Fix build break on symbol-prefixed archs
initramfs: fix initramfs size calculation
initramfs: generalize initramfs_data.xxx.S variants
scripts/kallsyms: Enable error messages while hush up unnecessary warnings
scripts/setlocalversion: update comment
kbuild: Use a single clean rule for kernel and external modules
kbuild: Do not run make clean in $(srctree)
scripts/mod/modpost.c: fix commentary accordingly to last changes
kbuild: Really don't clean bounds.h and asm-offsets.h
Allow machine drivers to explicitly enable the use of the dummy regulator,
enabling simpler support for systems with only a few specific supplies
visible to software.
It is strongly recommended that this is not used on systems with
substantial software control over their PMICs, for maximum functionality
constrints should be as fully specified as possible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3972 PMIC.
This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out
(LDO) regulators. LP3972 PMIC controller uses I2C interface.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV
with DVS support. In this initial release, users can set voltages for
four DVS modes, RAMP delay values, and SYNC frequency.
Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID
is not supported in this release.
If GPIO of EN is not valid in platform data, the driver assumes that it
is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down
VID0 and VID1 to fix DVS mode as 0 and disables DVS support.
We assume that V_OUT is capable to provide every voltage from 770mV to
1.40V in 10mV steps although the data sheet has some ambiguity on it.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
v2:
- Style correction
- Can accept platform_data with invalid GPIOs
- Removed unnecessary features
- Improved error handling
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
This merges the staging-next tree to Linus's tree and resolves
some conflicts that were present due to changes in other trees that were
affected by files here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: add new sdhci-pxa driver for Marvell SoCs
mmc: make number of mmcblk minors configurable
mmc_spi: Recover from CRC errors for r/w operation over SPI.
mmc: sdhci-pltfm: add -pltfm driver for imx35/51
mmc: sdhci-of-esdhc: factor out common stuff
mmc: sdhci_pltfm: pass more data on custom init call
mmc: sdhci: introduce get_ro private write-protect hook
mmc: sdhci-pltfm: move .h file into appropriate subdir
mmc: sdhci-pltfm: Add structure for host-specific data
mmc: fix cb710 kconfig dependency warning
mmc: cb710: remove debugging printk (info duplicated from mmc-core)
mmc: cb710: clear irq handler on init() error path
mmc: cb710: remove unnecessary msleep()
mmc: cb710: implement get_cd() callback
mmc: cb710: partially demystify clock selection
mmc: add a file to debugfs for changing host clock at runtime
mmc: sdhci: allow for eMMC 74 clock generation by controller
mmc: sdhci: highspeed: check for mmc as well as sd cards
mmc: sdhci: Add Moorestown device support
mmc: sdhci: Intel Medfield support
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs: (28 commits)
net/9p: Return error on read with NULL buffer
9p: Add datasync to client side TFSYNC/RFSYNC for dotl
net/9p: Return error if we fail to encode protocol data
fs/9p: Use generic_file_open with lookup_instantiate_filp
fs/9p: Add missing iput in v9fs_vfs_lookup
fs/9p: Use mknod 9p operation on create without open request
net/9p: Add waitq to VirtIO transport.
[net/9p]Serialize virtqueue operations to make VirtIO transport SMP safe.
9p: Implement TREADLINK operation for 9p2000.L
9p: Use V9FS_MAGIC in statfs
9p: Implement TGETLOCK
9p: Implement TLOCK
[9p] Introduce client side TFSYNC/RFSYNC for dotl.
[fs/9p] Add file_operations for cached mode in dotl protocol.
fs/9p: Add access = client option to opt in acl evaluation.
fs/9p: Implement create time inheritance
fs/9p: Update ACL on chmod
fs/9p: Implement setting posix acl
fs/9p: Add xattr callbacks for POSIX ACL
fs/9p: Implement POSIX ACL permission checking function
...
Today's git tree fails to build on !CONFIG_BLOCK, due to upstream commit
367a51a339 ("fs: Add FITRIM ioctl"):
include/linux/fs.h:36: error: expected specifier-qualifier-list before ‘uint64_t’
include/linux/fs.h:36: error: expected specifier-qualifier-list before ‘uint64_t’
include/linux/fs.h:36: error: expected specifier-qualifier-list before ‘uint64_t’
The commit adds uint64_t type usage to fs.h, but linux/types.h is not included
explicitly - it's only included implicitly via linux/blk_types.h, and there only if
CONFIG_BLOCK is enabled.
Add the explicit #include to fix this.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SYNOPSIS
size[4] Tfsync tag[2] fid[4] datasync[4]
size[4] Rfsync tag[2]
DESCRIPTION
The Tfsync transaction transfers ("flushes") all modified in-core data of
file identified by fid to the disk device (or other permanent storage
device) where that file resides.
If datasync flag is specified data will be fleshed but does not flush
modified metadata unless that metadata is needed in order to allow a
subsequent data retrieval to be correctly handled.
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] TReadlink tag[2] fid[4]
size[4] RReadlink tag[2] target[s]
Description
Readlink is used to return the contents of the symoblic link
referred by fid. Contents of symboic link is returned as a
response.
target[s] - Contents of the symbolic link referred by fid.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Use V9FS_MAGIC as the file system type while filling kernel statfs
strucutre instead of using host file system magic number. Also move
the definition of V9FS_MAGIC from v9fs.h to standard magic.h file.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] TGetlock tag[2] fid[4] getlock[n]
size[4] RGetlock tag[2] getlock[n]
Description
TGetlock is used to test for the existence of byte range posix locks on a file
identified by given fid. The reply contains getlock structure. If the lock could
be placed it returns F_UNLCK in type field of getlock structure. Otherwise it
returns the details of the conflicting locks in the getlock structure
getlock structure:
type[1] - Type of lock: F_RDLCK, F_WRLCK
start[8] - Starting offset for lock
length[8] - Number of bytes to check for the lock
If length is 0, check for lock in all bytes starting at the location
'start' through to the end of file
pid[4] - PID of the process that wants to take lock/owns the task
in case of reply
client[4] - Client id of the system that owns the process which
has the conflicting lock
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Synopsis
size[4] TLock tag[2] fid[4] flock[n]
size[4] RLock tag[2] status[1]
Description
Tlock is used to acquire/release byte range posix locks on a file
identified by given fid. The reply contains status of the lock request
flock structure:
type[1] - Type of lock: F_RDLCK, F_WRLCK, F_UNLCK
flags[4] - Flags could be either of
P9_LOCK_FLAGS_BLOCK - Blocked lock request, if there is a
conflicting lock exists, wait for that lock to be released.
P9_LOCK_FLAGS_RECLAIM - Reclaim lock request, used when client is
trying to reclaim a lock after a server restrart (due to crash)
start[8] - Starting offset for lock
length[8] - Number of bytes to lock
If length is 0, lock all bytes starting at the location 'start'
through to the end of file
pid[4] - PID of the process that wants to take lock
client_id[4] - Unique client id
status[1] - Status of the lock request, can be
P9_LOCK_SUCCESS(0), P9_LOCK_BLOCKED(1), P9_LOCK_ERROR(2) or
P9_LOCK_GRACE(3)
P9_LOCK_SUCCESS - Request was successful
P9_LOCK_BLOCKED - A conflicting lock is held by another process
P9_LOCK_ERROR - Error while processing the lock request
P9_LOCK_GRACE - Server is in grace period, it can't accept new lock
requests in this period (except locks with
P9_LOCK_FLAGS_RECLAIM flag set)
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
