Detected these variables by building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Commit f3ddac1918 ("[SCSI] qla2xxx:
Disable adapter when we encounter a PCI disconnect.") has introduced a
code that disables the board, releasing some resources, when reading
0xffffffff.
In case this happens when there is an EEH, this read will trigger EEH
detection and set PCI channel offline. EEH will be able to recover the
card from this state by doing a reset, so it's a better option than
simply disabling the card.
Since eeh_check_failure will mark the channel as offline before
returning the read value, in case there really was an EEH, we can simply
check for pci_channel_offline, preventing the board_disable code from
running if it's true.
Without this patch, EEH code will try to access those same resources
that board_disable will try to free. This race can cause EEH recovery to
fail.
[ 504.370577] EEH: Notify device driver to resume
[ 504.370580] qla2xxx [0001:07:00.0]-9002:2: The device failed to resume I/O from slot/link_reset.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
For FA-WWPN is enabled port, if NPIV created on that port and,
if port link is brought down, then WWPN was restored from flash for both
physical and NPIV port. This will result in NPIV port and physical port
sharing same WWPN. Any application refreshing ports information will
not be able to scan NPIV port because of this behavior. So while restoring WWPN,
only restore physical port WWPN.
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
On some vendor switches, when switch port is toggled (down /up),
then in some condition driver tries to configure virtual port,
before FW is actually in ready state to process any commands on wire.
At this time, configuring virtual port can fail. Add fix in driver
to make driver wait, for FW to be ready state before
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
For FA-WWPN capable device, ISP2031 and ISP27XX, when loop
dead is detected by a driver, restore WWPN from NVRAM.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Parse the retry delay timer field from the FCP response data and if:
- It is not zero
- The SCSI status is busy or queue full
return SCSI_MLQUEUE_TARGET_BUSY for the number of milliseconds specified
in the retry delay timer field.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for the D-port (diagnostic port) fabric switch feature.
(Fabric Switch initiates loopback style port testing)
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Semaphore register does not exist for ISPFx00.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The PCI register read checking introduced in commit fe1b806f4f
("qla2xxx: Disable adapter when we encounter a PCI disconnect") is
active during driver probe. Hold off scheduling any board removal until
the driver probe has completed. This ensures that the the board_disable
work structure is initialized and more importantly, avoids racing
qla2x00_probe_one.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Introduce mutual exclusion between the qla2xxx_remove_one PCI driver
callback and qla2x00_disable_board_on_pci_error, which is scheduled as
board_disable work by qla2x00_check_reg{32,16}_for_disconnect:
* Leave the driver-specific data attached to the underlying PCI device
intact in qla2x00_disable_board_on_pci_error, so that qla2x00_remove_one
has enough breadcrumbs to determine that any board_disable work has been
completed.
* In qla2xxx_remove_one, set a bit to prevent any subsequent
board_disable work from scheduling, then cancel and wait until pending
work has completed.
* Reuse the PCI device enable count check in qla2x00_remove_one to
determine if board_disable has occured. The original purpose of this
check was unnecessary since the driver remove function wasn't called
when the probe fails.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are various callers of qla2x00_check_reg{32,16}_for_disconnect
that may schedule board removal on PCI-disconnect. Test-and-set a
dedicated flag before scheduling board_disable so it is invoked only
once.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add an uint16_t variant of qla2x00_check_reg_for_disconnect and use
these routines to check and schedule a PCI-disconnected board from a
centralized place.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Limiting which port update events will allow the driver to kick off a
name server scan has been problematic in some corner cases so remove the
restriction and restore the previous semantic. Also move the link
up/down informational messages to the LOOP_UP and LOOP_DOWN events.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Log message code 0x00c6 preserved, although it is reported
after successful call to pci_enable_msix_range(), not before
possibly unsuccessful call to pci_enable_msix(). Consumers
of the error code should not notice the difference.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: qla2xxx-upstream@qlogic.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add support for T10-Dif for Target Mode to qla driver.
The driver will look for firmware attribute that support
this feature. When the feature is present, the capabilities
will be report to TCM layer.
Add CTIO CRC2 iocb to build T10-Dif commands.
Add support routines to process good & error cases.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If an adapter reset is already in progress, do not schedule another one when
we receive an invalid status handle.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Send aborts to the firmware via the request/response queue mechanism.
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Fix interpreting the wrong IOCB type for task management
functions in the response path.
- Merge the task management function handling for various adapters.
Signed-off-by: Armen Baloyan <armen.baloyan@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fixes requesting of the MSI-X vectors for the base response queue.
The iteration in the for loop in qla24xx_enable_msix() was incorrect.
We should only iterate of the first two MSI-X vectors and not the total
number of MSI-X vectors that have given to the driver for this device
from pci_enable_msix() in this function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If we become disconnected from the PCI bus/PCIe fabric, there can be long delays
in register reads which can cause erroneous decisions to be made and cause a
soft lockup if a lock is held too long. As a preventative measure, check for a
disconnection (register reads that return -1) and then disable the board if we
find ourselves in this condition. For now, check in our interrupt handlers and
the per adapter one second timer.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If an invalid IOCB is returned on the response queue then the index into the
request queue map could be invalid and could return to us a bogus value. This
could cause us to try to deference an invalid pointer and cause an exception.
If we encounter this condition, simply return as no context can be established
for this response.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Earlier IDC-TIME-EXTEND aen was a nop and ignored by driver.
We now have to handle the aen so that other protocol drivers can use time
extension during some loopback operations.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The patch changes a specifier used to output some variables. Instead of using
stack for each byte the '%*ph[CN]' allows to take a one pointer and prints
entire buffer as a hexadecimal string with the separator ':' or ''.
Signed-off-by: Oleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change the 'rval' variable from QLA_FUNCTION_TIMEOUT into QLA_SUCCESS
before starting a loop that is only executed if rval is initialized
to QLA_SUCCESS. Coverity reported that loop as "dead code".
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The driver uses ha->mbx_cmd_flags variable to pass information between
its ISR and mailbox routines, however, it does so without the protection of
any locks. Under certain conditions, this can lead to multiple mailbox
command completions being signaled, which, in turn, leads to a false
mailbox timeout error for the subsequently issued mailbox command.
The issue occurs frequently but intermittenly with the Qlogic 8GFC mezz
card during card initialization, resulting in card initialization failure.
Signed-off-by: Gurinder (Sunny) Shergill <gurinder.shergill@hp.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wait for the IDC complete AEN before returning the loopback operation back to
the application to make sure the port is put back into normal operations.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently,the driver is processes RSCNs for each new NPIV ports that is created.
Processing the RSCN includes a name server query to see what has changed at the
name server side. The name server query is performed by the physical port and
each virtual port on the physical adapter (since the RSCN is passed to each
virtual port for processing). As the number of virtual ports being created
increases, this causes a lot of traffic and busies the firmware.
Processing the RSCN for a virtual port we already have a priori knowledge of is
not necessary so check the 24-bit fabric ID of the RSCN entry and skip
processing it if the RSCN is for a virtual port we already know about.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the following error handling for loopback diagnostic mode with ISP83xx:
1. If we do not receive an MBA_DCBX_COMPLETE after our initial set port
configuration command, try to reset the port back into normal operation.
If that fails, take a FCoE dump and then reset the chip.
2. After completing the loopback diagnostic operation, if the reset of the port
back into normal operation fails then reset the port so we take a FCoE dump
and then reset the chip.
3. When we receive an IDC notification and the requested operation is loopback
extend the loop down timer so the link does not appear to down for an
extended period of time.
[jejb: fix checkpatch issue]
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Parameterize qla2x00_get_link_speed_str() to be generic on link speed.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
