After triggering the mm switch with a load of PD_DIR, which may be
deferred unto the MI_SET_CONTEXT on rcs, serialise the next commands
with that load by posting a read of PD_DIR (or else those subsequent
commands may access the stale page tables).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611171825.13678-2-chris@chris-wilson.co.uk
The HW only accepts offsets within ring->size, and fails peculiarly if
the RING_HEAD or RING_TAIL is set to ring->size. Therefore whenever we
set ring->head/ring->tail we want to make sure it is within value (using
intel_ring_wrap()).
v2: Double check execlists as well
v3: Remove redundancy with assert_ring_tail_valid()
v4: Just assert in intel_ring_reset() rather than be over-defensive.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20180611110845.31890-2-chris@chris-wilson.co.uk
The discovery with trying to enable full-ppgtt was that we were
completely failing to the load both the mm and context following the
reset. Although we were performing mmio to set the PP_DIR (per-process
GTT) and CCID (context), these were taking no effect (the assumption was
that this would trigger reload of the context and restore the page
tables). It was not until we performed the LRI + MI_SET_CONTEXT in a
following context switch would anything occur.
Since we are then required to reset the context image and PP_DIR using
CS commands, we place those commands into every batch. The hardware
should recognise the no-ops and eliminate the expensive context loads,
but we still have to pay the cost of using cross-powerwell register
writes. In practice, this has no effect on actual context switch times,
and only adds a few hundred nanoseconds to no-op switches. We can improve
the latter by eliminating the w/a around known no-op switches, but there
is an ulterior motive to keeping them.
Always emitting the context switch at the beginning of the request (and
relying on HW to skip unneeded switches) does have one key advantage.
Should we implement request reordering on Haswell, we will not know in
advance what the previous executing context was on the GPU and so we
would not be able to elide the MI_SET_CONTEXT commands ourselves and
always have to emit them. Having our hand forced now actually prepares
us for later.
Now since that context and mm follow the request, we no longer (and not
for a long time since requests took over!) require a trace point to tell
when we write the switch into the ring, since it is always. (This is
even more important when you remember that simply writing into the ring
bears no relation to the current mm.)
v2: Sandybridge has to agree to use LRI as well.
Testcase: igt/drv_selftests/live_hangcheck
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180611110845.31890-1-chris@chris-wilson.co.uk
We want to be able to reset the GPU from inside a timer callback
(hardirq context). One step requires us to copy the default context
state over to the guilty context, which means we need to plan in advance
to have that object accessible from within an atomic context. The atomic
context prevents us from pinning the object or from peeking into the
shmemfs backing store (all may sleep), so we choose to pin the
default_state into memory when the engine becomes active. This
compromise allows us to swap out the default state when idle, when
required.
References: 5692251c25 ("drm/i915/lrc: Scrub the GPU state of the guilty hanging request")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180518090212.5349-2-chris@chris-wilson.co.uk
To ease the frequent and ugly pointer dance of
&request->gem_context->engine[request->engine->id] during request
submission, store that pointer as request->hw_context. One major
advantage that we will exploit later is that this decouples the logical
context state from the engine itself.
v2: Set mock_context->ops so we don't crash and burn in selftests.
Cleanups from Tvrtko.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180517212633.24934-3-chris@chris-wilson.co.uk
We cannot call kthread_park() from softirq context, so let's avoid it
entirely during the reset. We wanted to suspend the signaler so that it
would not mark a request as complete at the same time as we marked it as
being in error. Instead of parking the signaling, stop the engine from
advancing so that the GPU doesn't emit the breadcrumb for our chosen
"guilty" request.
v2: Refactor setting STOP_RING so that we don't have the same code thrice
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michałt Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180516183355.10553-8-chris@chris-wilson.co.uk
In preparation to more carefully handling incomplete preemption during
reset by execlists, we move the existing code wholesale to the backends
under a couple of new reset vfuncs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
CC: Michel Thierry <michel.thierry@intel.com>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180516183355.10553-4-chris@chris-wilson.co.uk
We need to move to a more flexible timeline that doesn't assume one
fence context per engine, and so allow for a single timeline to be used
across a combination of engines. This means that preallocating a fence
context per engine is now a hindrance, and so we want to introduce the
singular timeline. From the code perspective, this has the notable
advantage of clearing up a lot of mirky semantics and some clumsy
pointer chasing.
By splitting the timeline up into a single entity rather than an array
of per-engine timelines, we can realise the goal of the previous patch
of tracking the timeline alongside the ring.
v2: Tweak wait_for_idle to stop the compiling thinking that ret may be
uninitialised.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502163839.3248-2-chris@chris-wilson.co.uk
In the future, we want to move a request between engines. To achieve
this, we first realise that we have two timelines in effect here. The
first runs through the GTT is required for ordering vma access, which is
tracked currently by engine. The second is implied by sequential
execution of commands inside the ringbuffer. This timeline is one that
maps to userspace's expectations when submitting requests (i.e. given the
same context, batch A is executed before batch B). As the rings's
timelines map to userspace and the GTT timeline an implementation
detail, move the timeline from the GTT into the ring itself (per-context
in logical-ring-contexts/execlists, or a global per-engine timeline for
the shared ringbuffers in legacy submission.
The two timelines are still assumed to be equivalent at the moment (no
migrating requests between engines yet) and so we can simply move from
one to the other without adding extra ordering.
v2: Reinforce that one isn't allowed to mix the engine execution
timeline with the client timeline from userspace (on the ring).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502163839.3248-1-chris@chris-wilson.co.uk
We don't need to track every ring for its lifetime as they are managed
by the contexts/engines. What we do want to track are the live rings so
that we can sporadically clean up requests if userspace falls behind. We
can simply restrict the gt->rings list to being only gt->live_rings.
v2: s/live/active/ for consistency with gt.active_requests
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180430131503.5375-4-chris@chris-wilson.co.uk
In the next patch, rings are the central timeline as requests may jump
between engines. Therefore in the future as we retire in order along the
engine timeline, we may retire out-of-order within a ring (as the ring now
occurs along multiple engines), leading to much hilarity in miscomputing
the position of ring->head.
As an added bonus, retiring along the ring reduces the penalty of having
one execlists client do cleanup for another (old legacy submission
shares a ring between all clients). The downside is that slow and
irregular (off the critical path) process of cleaning up stale requests
after userspace becomes a modicum less efficient.
In the long run, it will become apparent that the ordered
ring->request_list matches the ring->timeline, a fun challenge for the
future will be unifying the two lists to avoid duplication!
v2: We need both engine-order and ring-order processing to maintain our
knowledge of where individual rings have completed upto as well as
knowing what was last executing on any engine. And finally by decoupling
retiring the contexts on the engine and the timelines along the rings,
we do have to keep a reference to the context on each request
(previously it was guaranteed by the context being pinned).
v3: Not just a reference to the context, but we need to keep it pinned
as we manipulate the rings; i.e. we need a pin for both the manipulation
of the engine state during its retirements, and a separate pin for the
manipulation of the ring state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180430131503.5375-3-chris@chris-wilson.co.uk
We can convert engine stats from a spinlock to seqlock to ensure interrupt
processing is never even a tiny bit delayed by parallel readers.
There is a smidgen bit more cost on the write lock side, and an extremely
unlikely chance that readers will have to retry a few times in face of
heavy interrupt load. But it should be extremely unlikely given how
lightweight read side section is compared to the interrupt processing
side, and also compared to the rest of the code paths which can lead into
it. Furthermore, writer is the ones doing the real, latency sensitive
work, while readers are only informative.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426074716.7352-1-tvrtko.ursulin@linux.intel.com
Today we only want to pass along the priority to engine->schedule(), but
in the future we want to have much more control over the various aspects
of the GPU during a context's execution, for example controlling the
frequency allowed. As we need an ever growing number of parameters for
scheduling, move those into a struct for convenience.
v2: Move the anonymous struct into its own function for legibility and
ye olde gcc.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180418184052.7129-3-chris@chris-wilson.co.uk
This has grown to be a sizable amount of code, so move it to
its own file before we try to refactor anything. For the moment,
we are leaving behind the WA BB code and the WAs that get applied
(incorrectly) in init_clock_gating, but we will deal with it later.
v2: Use intel_ prefix for code that deals with the hardware (Chris)
v3: Rebased
v4:
- Rebased
- New license header
v5:
- Rebased
- Added some organisational notes to the file (Chris)
v6: Include DOC section in the documentation build (Jani)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[ickle: appease checkpatch, mostly]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1523376767-18480-1-git-send-email-oscar.mateo@intel.com
Let's avoid having to delve down the pointer chain to see if the i915
device has support for preemption and store that on the engine, which
made the decision in the first place!
v2: Refactor common preemption policy between execlists/guc.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180403183537.5522-1-chris@chris-wilson.co.uk
We would like to start doing some bookkeeping at the beginning, between
contexts and at the end of execlists submission. We already mark the
beginning and end using EXECLISTS_ACTIVE_USER, to provide an indication
when the HW is idle. This give us a pair of sequence points we can then
expand on for further bookkeeping.
v2: Refactor guc submission to share the same begin/end.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180331130626.10712-1-chris@chris-wilson.co.uk
ICL 11 has a greater number of maximum subslices. This patch
reflects this.
v2: GEN11 updates to MCR_SELECTOR (Oscar)
v3: Copypasta error in the new defines (Lionel)
Bspec: 21139
BSpec: 21108
Signed-off-by: Kelvin Gardiner <kelvin.gardiner@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com> (v1)
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> (v1)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180316121456.11577-3-mika.kuoppala@linux.intel.com
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
The only usage outside the intel_lrc.c file is in the ringbuffer
init, but the irq mask calculated there is then overwritten for
all engines that have a non-zero shift, so we can drop it.
This change is not aimed at code saving but at removing from
intel_engines information that does not apply to all gens that have
the engine. When checking without the temporary WARN_ON, code size
is basically unchanged.
v2: make the irq_shifts array static const
v3: rebase, move irq_shifts array to logical_ring_default_irqs
v4: move array inside the if and use u8 for it (Chris)
Suggested-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314182653.26981-4-daniele.ceraolospurio@intel.com
There is some redundancy between dma_fence->ops->enable_signaling (via
i915_fence_enable_signaling) and our backend,
intel_engine_enable_signaling() in that both levels recheck the fence
status multiple times. If we convert intel_engine_enable_signaling() to
return the information desired by dma_fence->ops->enable_signaling, we
can reduce i915_fence_enable_signaling to a simple stub and avoid
trying to reinterpret the same information.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308140732.25090-1-chris@chris-wilson.co.uk
Header intel_ringbuffer.h is using definitions from i915_reg.h
but forget to include it. Remove this hidden dependency by
explicitly include missing header.
v2: add reminder (Chris)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180308095037.18264-2-michal.wajdeczko@intel.com
Up to now, subslice mask was assumed to be uniform across slices. But
starting with Cannonlake, slices can be asymmetric (for example slice0
has different number of subslices as slice1+). This change stores all
subslices masks for all slices rather than having a single mask that
applies to all slices.
v2: Rework how we store total numbers in sseu_dev_info (Tvrtko)
Fix CHV eu masks, was reading disabled as enabled (Tvrtko)
Readability changes (Tvrtko)
Add EU index helper (Tvrtko)
v3: Turn ALIGN(v, 8) / 8 into DIV_ROUND_UP(v, BITS_PER_BYTE) (Tvrtko)
Reuse sseu_eu_idx() for setting eu_mask on CHV (Tvrtko)
Reformat debug prints for subslices (Tvrtko)
v4: Change eu_mask helper into sseu_set_eus() (Tvrtko)
v5: With Haswell reporting masks & counts, bump sseu_*_eus() functions
to use u16 (Lionel)
v6: Fix sseu_get_eus() for > 8 EUs per subslice (Lionel)
v7: Change debugfs enabels for number of subslices per slice, will
need a small igt/pm_sseu change (Lionel)
Drop subslice_total field from sseu_dev_info, rely on
sseu_subslice_total() to recompute the value instead (Lionel)
v8: Remove unused function compute_subslice_total() (Lionel)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306122857.27317-2-lionel.g.landwerlin@intel.com
Enhanced Execlists is an upgraded version of execlists which supports
up to 8 ports. The lrcs to be submitted are written to a submit queue
(the ExecLists Submission Queue - ELSQ), which is then loaded on the
HW. When writing to the ELSP register, the lrcs are written cyclically
in the queue from position 0 to position 7. Alternatively, it is
possible to write directly in the individual positions of the queue
using the ELSQC registers. To be able to re-use all the existing code
we're using the latter method and we're currently limiting ourself to
only using 2 elements.
v2: Rebase.
v3: Switch from !IS_GEN11 to GEN < 11 (Daniele Ceraolo Spurio).
v4: Use the elsq registers instead of elsp. (Daniele Ceraolo Spurio)
v5: Reword commit, rename regs to be closer to specs, turn off
preemption (Daniele), reuse engine->execlists.elsp (Chris)
v6: use has_logical_ring_elsq to differentiate the new paths
v7: add preemption support, rename els to submit_reg (Chris)
v8: save the ctrl register inside the execlists struct, drop CSB
handling updates (superseded by preempt_complete_status) (Chris)
v9: s/drm_i915_gem_request/i915_request (Mika)
v10: resolved conflict in inject_preempt_context (Mika)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302161501.28594-4-mika.kuoppala@linux.intel.com
Previously, we would spin waiting for all waiters to wake up and notice
their request had completed before we would reset the seqno upon
wraparound. However, we can mark their waits as complete and wake them
up directly using the existing machinery for handling the flushing of
missed wakeups when idling.
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306130143.13312-2-chris@chris-wilson.co.uk
The goal here is to try and reduce the latency of signaling additional
requests following the wakeup from interrupt by reducing the list of
to-be-signaled requests from an rbtree to a sorted linked list. The
original choice of using an rbtree was to facilitate random insertions
of request into the signaler while maintaining a sorted list. However,
if we assume that most new requests are added when they are submitted,
we see those new requests in execution order making a insertion sort
fast, and the reduction in overhead of each signaler iteration
significant.
Since commit 56299fb7d9 ("drm/i915: Signal first fence from irq handler
if complete"), we signal most fences directly from notify_ring() in the
interrupt handler greatly reducing the amount of work that actually
needs to be done by the signaler kthread. All the thread is then
required to do is operate as the bottom-half, cleaning up after the
interrupt handler and preparing the next waiter. This includes signaling
all later completed fences in a saturated system, but on a mostly idle
system we only have to rebuild the wait rbtree in time for the next
interrupt. With this de-emphasis of the signaler's role, we want to
rejig it's datastructures to reduce the amount of work we require to
both setup the signal tree and maintain it on every interrupt.
References: 56299fb7d9 ("drm/i915: Signal first fence from irq handler if complete")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222092545.17216-1-chris@chris-wilson.co.uk
Gen11 will add more VCS and VECS rings so prepare the
infrastructure to support that.
Bspec: 7021
v2: Rebase.
v3: Rebase.
v4: Rebase.
v5: Rebase.
v6:
- Update for POR changes. (Daniele Ceraolo Spurio)
- Add provisional guc engine ids - to be checked and confirmed.
v7:
- Rebased.
- Added the new ring masks.
- Added the new HW ids.
v8:
- Introduce I915_MAX_VCS/VECS to avoid magic numbers (Michal)
v9: increase MAX_ENGINE_INSTANCE to 3
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180228101153.7224-1-mika.kuoppala@linux.intel.com
Sometimes we need to boost the priority of an in-flight request, which
may lead to the situation where the second submission port then contains
a higher priority context than the first and so we need to inject a
preemption event. To do so we must always check inside
execlists_dequeue() whether there is a priority inversion between the
ports themselves as well as the head of the priority sorted queue, and we
cannot just skip dequeuing if the queue is empty.
As Michał noted, this doesn't simply extend to handling more than 2-port
submission, as we may need to reorder within the array of executing
requests which themselves are lower priority than the first. A task for
later!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180222142229.14517-1-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
We want to de-emphasize the link between the request (dependency,
execution and fence tracking) from GEM and so rename the struct from
drm_i915_gem_request to i915_request. That is we may implement the GEM
user interface on top of requests, but they are an abstraction for
tracking execution rather than an implementation detail of GEM. (Since
they are not tied to HW, we keep the i915 prefix as opposed to intel.)
In short, the spatch:
@@
@@
- struct drm_i915_gem_request
+ struct i915_request
A corollary to contracting the type name, we also harmonise on using
'rq' shorthand for local variables where space if of the essence and
repetition makes 'request' unwieldy. For globals and struct members,
'request' is still much preferred for its clarity.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221095636.6649-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
When dumping the engine, we print out the current register values. This
requires the rpm wakeref. If the device is alseep, we can assume the
engine is asleep (and the register state is uninteresting) so skip and
only acquire the rpm wakeref if the device is already awake.
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180212102415.24246-1-chris@chris-wilson.co.uk
If we remove some hardcoded assumptions about the preempt context having
a fixed id, reserved from use by normal user contexts, we may only
allocate the i915_gem_context when required. Then the subsequent
decisions on using preemption reduce to having the preempt context
available.
v2: Include an assert that we don't allocate the preempt context twice.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180207210544.26351-3-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Commit 99e48bf98d ("drm/i915: Lock out execlist tasklet while peeking
inside for busy-stats") added a tasklet_disable call in busy stats
enabling, but we failed to understand that the PMU enable callback runs
as an hard IRQ (IPI).
Consequence of this is that the PMU enable callback can interrupt the
execlists tasklet, and will then deadlock when it calls
intel_engine_stats_enable->tasklet_disable.
To fix this, I realized it is possible to move the engine stats enablement
and disablement to PMU event init and destroy hooks. This allows for much
simpler implementation since those hooks run in normal context (can
sleep).
v2: Extract engine_event_destroy. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 99e48bf98d ("drm/i915: Lock out execlist tasklet while peeking inside for busy-stats")
Testcase: igt/perf_pmu/enable-race-*
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205093448.13877-1-tvrtko.ursulin@linux.intel.com
Pass in a format string (and args) to specify the header to be emitted
along with the engine state when pretty-printing. This allows the header
to be emitted inside the drm_printer stream, so sharing the same prefix
and output characteristics (e.g. debug level and filtering).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171208012303.25504-2-chris@chris-wilson.co.uk
Chris requested this backmerge for a reconciliation on
drm_print.h between drm-misc-next and drm-intel-next-queued
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Currently on every submission, we recalculate the ELSP register offset
for the engine, after chasing the pointers to find the iomem base. Since
this is fixed for the lifetime of the driver, record the offset in the
execlists struct.
In practice the difference is negligible, it just happens to remove 27
bytes of eyesore pointer dancing from next to the hottest instruction
(which is itself due to stalling for a cache miss) in perf profiles of
the execlists_submission_tasklet().
v2: Trim off one more elsp local.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171207222434.17686-1-chris@chris-wilson.co.uk
- Init clock gate fix (Ville)
- Execlists event handling corrections (Chris, Michel)
- Improvements on GPU Cache invalidation and context switch (Chris)
- More perf OA changes (Lionel)
- More selftests improvements and fixes (Chris, Matthew)
- Clean-up on modules parameters (Chris)
- Clean-up around old ringbuffer submission and hw semaphore on old platforms (Chris)
- More Cannonlake stabilization effort (David, James)
- Display planes clean-up and improvements (Ville)
- New PMU interface for perf queries... (Tvrtko)
- ... and other subsequent PMU changes and fixes (Tvrtko, Chris)
- Remove success dmesg noise from rotation (Chris)
- New DMC for Kabylake (Anusha)
- Fixes around atomic commits (Daniel)
- GuC updates and fixes (Sagar, Michal, Chris)
- Couple gmbus/i2c fixes (Ville)
- Use exponential backoff for all our wait_for() (Chris)
- Fixes for i915/fbdev (Chris)
- Backlight fixes (Arnd)
- Updates on shrinker (Chris)
- Make Hotplug enable more robuts (Chris)
- Disable huge pages (TPH) on lack of a needed workaround (Joonas)
- New GuC images for SKL, KBL, BXT (Sagar)
- Add HW Workaround for Geminilake performance (Valtteri)
- Fixes for PPS timings (Imre)
- More IPS fixes (Maarten)
- Many fixes for Display Port on gen2-gen4 (Ville)
- Retry GPU reset making the recover from hang more robust (Chris)
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaIf0wAAoJEPpiX2QO6xPK/wAH/0JrYX+oml+ZJ7xV4wxm0S5S
K8jcSWQPlF78xkuiVaA0200qOPJP4Yp32Gmv7dVBFKq7IaLn3c8B2DjqE3D0QPue
ZPSMMFz7NTMVjfKpmkCp9V3ln87Cc/Cj0L66CKRuFnvefDCGLN4hULj3NAxQfkwm
9CsUH+p5d7usXgIB7tIovNEKw4hLiTQiTUd5bwok6iJ3EB79DHxxlY8nG6n5ukEr
9XryS1ADGmTUy7YifIdJKPyDLjEeP+xRMApUva67y7zaTk7iW6mETkBJ7WpQbCCL
fQaLlmU/SrBD8ViJBx19U6ofKIVJ+vVMoU9JNg4Ak5WZOfjw7aIPiZaaHU3Aj+w=
=IutN
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2017-12-01' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
[airlied: fix conflict in intel_dsi.c]
drm-intel-next-2017-12-01:
- Init clock gate fix (Ville)
- Execlists event handling corrections (Chris, Michel)
- Improvements on GPU Cache invalidation and context switch (Chris)
- More perf OA changes (Lionel)
- More selftests improvements and fixes (Chris, Matthew)
- Clean-up on modules parameters (Chris)
- Clean-up around old ringbuffer submission and hw semaphore on old platforms (Chris)
- More Cannonlake stabilization effort (David, James)
- Display planes clean-up and improvements (Ville)
- New PMU interface for perf queries... (Tvrtko)
- ... and other subsequent PMU changes and fixes (Tvrtko, Chris)
- Remove success dmesg noise from rotation (Chris)
- New DMC for Kabylake (Anusha)
- Fixes around atomic commits (Daniel)
- GuC updates and fixes (Sagar, Michal, Chris)
- Couple gmbus/i2c fixes (Ville)
- Use exponential backoff for all our wait_for() (Chris)
- Fixes for i915/fbdev (Chris)
- Backlight fixes (Arnd)
- Updates on shrinker (Chris)
- Make Hotplug enable more robuts (Chris)
- Disable huge pages (TPH) on lack of a needed workaround (Joonas)
- New GuC images for SKL, KBL, BXT (Sagar)
- Add HW Workaround for Geminilake performance (Valtteri)
- Fixes for PPS timings (Imre)
- More IPS fixes (Maarten)
- Many fixes for Display Port on gen2-gen4 (Ville)
- Retry GPU reset making the recover from hang more robust (Chris)
* tag 'drm-intel-next-2017-12-01' of git://anongit.freedesktop.org/drm/drm-intel: (101 commits)
drm/i915: Update DRIVER_DATE to 20171201
drm/i915/cnl: Mask previous DDI - PLL mapping
drm/i915: Remove unsafe i915.enable_rc6
drm/i915: Sleep and retry a GPU reset if at first we don't succeed
drm/i915: Interlaced DP output doesn't work on VLV/CHV
drm/i915: Pass crtc state to intel_pipe_{enable,disable}()
drm/i915: Wait for pipe to start on i830 as well
drm/i915: Fix vblank timestamp/frame counter jumps on gen2
drm/i915: Fix deadlock in i830_disable_pipe()
drm/i915: Fix has_audio readout for DDI A
drm/i915: Don't add the "force audio" property to DP connectors that don't support audio
drm/i915: Disable DP audio for g4x
drm/i915/selftests: Wake the device before executing requests on the GPU
drm/i915: Set fake_vma.size as well as fake_vma.node.size for capture
drm/i915: Tidy up signed/unsigned comparison
drm/i915: Enable IPS with only sprite plane visible too, v4.
drm/i915: Make ips_enabled a property depending on whether IPS is enabled, v3.
drm/i915: Avoid PPS HW/SW state mismatch due to rounding
drm/i915: Skip switch-to-kernel-context on suspend when wedged
drm/i915/glk: Apply WaProgramL3SqcReg1DefaultForPerf for GLK too
...
- Many improvements for selftests and other igt tests (Chris)
- Forcewake with PUNIT->PMIC bus fixes and robustness (Hans)
- Define an engine class for uABI (Tvrtko)
- Context switch fixes and improvements (Chris)
- GT powersavings and power gating simplification and fixes (Chris)
- Other general driver clean-ups (Chris, Lucas, Ville)
- Removing old, useless and/or bad workarounds (Chris, Oscar, Radhakrishna)
- IPS, pipe config, etc in preparation for another Fast Boot attempt (Maarten)
- OA perf fixes and support to Coffee Lake and Cannonlake (Lionel)
- Fixes around GPU fault registers (Michel)
- GEM Proxy (Tina)
- Refactor of Geminilake and Cannonlake plane color handling (James)
- Generalize transcoder loop (Mika Kahola)
- New HW Workaround for Cannonlake and Geminilake (Rodrigo)
- Resume GuC before using GEM (Chris)
- Stolen Memory handling improvements (Ville)
- Initialize entry in PPAT for older compilers (Chris)
- Other fixes and robustness improvements on execbuf (Chris)
- Improve logs of GEM_BUG_ON (Mika Kuoppala)
- Rework with massive rename of GuC functions and files (Sagar)
- Don't sanitize frame start delay if pipe is off (Ville)
- Cannonlake clock fixes (Rodrigo)
- Cannonlake HDMI 2.0 support (Rodrigo)
- Add a GuC doorbells selftest (Michel)
- Add might_sleep() check to our wait_for() (Chris)
Many GVT changes for 4.16:
- CSB HWSP update support (Weinan)
- GVT debug helpers, dyndbg and debugfs (Chuanxiao, Shuo)
- full virtualized opregion (Xiaolin)
- VM health check for sane fallback (Fred)
- workload submission code refactor for future enabling (Zhi)
- Updated repo URL in MAINTAINERS (Zhenyu)
- other many misc fixes
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaD2cyAAoJEPpiX2QO6xPKuiEH/2/J7Ebf5IRZtaTU+ke2uOI4
2YCdrn9F1guz6d+cZtsLPkJ9JwQlz9EftfB7KT+9dT8viEG0FFna9bV+Xz3wyGQ6
DRlP9tCFnCDaOyZBI5QshubuzldabPpfscPJI7/EMr91jtveGhKIhsRzHBxKCEZF
LKlAHtXAWSkTozmh6bU+wf5TEOFzYv2oquTVn5ZJrpYlqup/wEKh+KnL9eBQ3+Qp
FLnmKjInaadOV/uXQfeWstJuohG/pfcNm68OmDOxYNmwpeNnwbtfKT9eZeDtDZDy
dXj9mokeTwg4fBrXX/tyxuKogywxQSNFTqCU2yY9up+35ykmjVN8p/1BYi+GGe0=
=ePes
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2017-11-17-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
More change sets for 4.16:
- Many improvements for selftests and other igt tests (Chris)
- Forcewake with PUNIT->PMIC bus fixes and robustness (Hans)
- Define an engine class for uABI (Tvrtko)
- Context switch fixes and improvements (Chris)
- GT powersavings and power gating simplification and fixes (Chris)
- Other general driver clean-ups (Chris, Lucas, Ville)
- Removing old, useless and/or bad workarounds (Chris, Oscar, Radhakrishna)
- IPS, pipe config, etc in preparation for another Fast Boot attempt (Maarten)
- OA perf fixes and support to Coffee Lake and Cannonlake (Lionel)
- Fixes around GPU fault registers (Michel)
- GEM Proxy (Tina)
- Refactor of Geminilake and Cannonlake plane color handling (James)
- Generalize transcoder loop (Mika Kahola)
- New HW Workaround for Cannonlake and Geminilake (Rodrigo)
- Resume GuC before using GEM (Chris)
- Stolen Memory handling improvements (Ville)
- Initialize entry in PPAT for older compilers (Chris)
- Other fixes and robustness improvements on execbuf (Chris)
- Improve logs of GEM_BUG_ON (Mika Kuoppala)
- Rework with massive rename of GuC functions and files (Sagar)
- Don't sanitize frame start delay if pipe is off (Ville)
- Cannonlake clock fixes (Rodrigo)
- Cannonlake HDMI 2.0 support (Rodrigo)
- Add a GuC doorbells selftest (Michel)
- Add might_sleep() check to our wait_for() (Chris)
Many GVT changes for 4.16:
- CSB HWSP update support (Weinan)
- GVT debug helpers, dyndbg and debugfs (Chuanxiao, Shuo)
- full virtualized opregion (Xiaolin)
- VM health check for sane fallback (Fred)
- workload submission code refactor for future enabling (Zhi)
- Updated repo URL in MAINTAINERS (Zhenyu)
- other many misc fixes
* tag 'drm-intel-next-2017-11-17-1' of git://anongit.freedesktop.org/drm/drm-intel: (260 commits)
drm/i915: Update DRIVER_DATE to 20171117
drm/i915: Add a policy note for removing workarounds
drm/i915/selftests: Report ENOMEM clearly for an allocation failure
Revert "drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk"
drm/i915: Calculate g4x intermediate watermarks correctly
drm/i915: Calculate vlv/chv intermediate watermarks correctly, v3.
drm/i915: Pass crtc_state to ips toggle functions, v2
drm/i915: Pass idle crtc_state to intel_dp_sink_crc
drm/i915: Enable FIFO underrun reporting after initial fastset, v4.
drm/i915: Mark the userptr invalidate workqueue as WQ_MEM_RECLAIM
drm/i915: Add might_sleep() check to wait_for()
drm/i915/selftests: Add a GuC doorbells selftest
drm/i915/cnl: Extend HDMI 2.0 support to CNL.
drm/i915/cnl: Simplify dco_fraction calculation.
drm/i915/cnl: Don't blindly replace qdiv.
drm/i915/cnl: Fix wrpll math for higher freqs.
drm/i915/cnl: Fix, simplify and unify wrpll variable sizes.
drm/i915/cnl: Remove useless conversion.
drm/i915/cnl: Remove spurious central_freq.
drm/i915/selftests: exercise_ggtt may have nothing to do
...
Sagar noticed the check can be consolidated between the engine stats
implementation and the PMU.
My first choice was a static inline helper but that got into include
ordering mess quickly fast so I went with a macro instead. At some point
we should perhaps looking into taking out the non-ringubffer bits from
intel_ringbuffer.h into a new intel_engine.h or something.
v2: Use engine->flags. (Chris Wilson)
v3: Rebase and mark GuC as not yet supported. (Chris Wilson)
v4: Move flag setting to intel_engines_reset_default_submission.
(Chris Wilson)
v5: Move flag setting to logical_ring_setup.
v6: intel_engines_reset_default_submission is the wrong place to set the
flag - it needs to be in execlists_set_default_submission. (Sagar)
v7: Flag setting in logical_ring_setup is not required. (Chris)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com> (v6)
Link: https://patchwork.freedesktop.org/patch/msgid/20171129102805.22690-1-tvrtko.ursulin@linux.intel.com
Will be adding a new per-engine flags shortly so it makes sense
to consolidate.
v2: Keep the original code flow in intel_engine_cleanup_cmd_parser.
(Joonas Lahtinen)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129082409.18189-1-tvrtko.ursulin@linux.intel.com
The legacy context switch for ringbuffer submission is multistaged,
where each of those stages may fail. However, we were updating global
state after some stages, and so we had to force the incomplete request
to be submitted because we could not unwind. Save the global state
before performing the switches, and so enable us to unwind back to the
previous global state should any phase fail. We then must cancel the
request instead of submitting it should the construction fail.
v2: s/saved_ctx/from_ctx/; s/ctx/to_ctx/ etc.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123152631.31385-1-chris@chris-wilson.co.uk
We have agreed during the engine classes discussion that fields marked as
non-ABI are better left out altogether from uapi headers.
v2: Use a local define for maintanability. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171123100701.18430-1-tvrtko.ursulin@linux.intel.com
We can use engine busy stats instead of the sampling timer for
better accuracy.
By doing this we replace the stohastic sampling with busyness
metric derived directly from engine activity. This is context
switch interrupt driven, so as accurate as we can get from
software tracking.
As a secondary benefit, we can also not run the sampling timer
in cases only busyness metric is enabled.
v2: Rebase.
v3:
* Rebase, comments.
* Leave engine busyness controls out of workers.
v4: Checkpatch cleanup.
v5: Added comment to pmu_needs_timer change.
v6:
* Rebase.
* Fix style of some comments. (Chris Wilson)
v7: Rebase and commit message update. (Chris Wilson)
v8: Add delayed stats disabling to improve accuracy in face of
CPU hotplug events.
v9: Rebase.
v10: Rebase - i915_modparams.enable_execlists removal.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171121181852.16128-6-tvrtko.ursulin@linux.intel.com
Track total time requests have been executing on the hardware.
We add new kernel API to allow software tracking of time GPU
engines are spending executing requests.
Both per-engine and global API is added with the latter also
being exported for use by external users.
v2:
* Squashed with the internal API.
* Dropped static key.
* Made per-engine.
* Store time in monotonic ktime.
v3: Moved stats clearing to disable.
v4:
* Comments.
* Don't export the API just yet.
v5: Whitespace cleanup.
v6:
* Rename ref to active.
* Drop engine aggregate stats for now.
* Account initial busy period after enabling stats.
v7:
* Rebase.
v8:
* Move context in notification after the notifier. (Chris Wilson)
v9:
In cases where stats tracking is getting disabled while there is
an active context on an engine, add up the current value to the
total. This also implies we don't clear the total when tracking
is disabled any longer. There is no real need to do so because
we define the stats as relative while enabled, meaning
comparison between two samples while tracking is enabled is the
valid usage. However, when busy stats will later be plugged into
the perf PMU API, it is beneficial to not reset the total, since
the PMU core likes to do some counter disable/enable cycles on
startup, and while doing so during a single long context
executing on an engine we would lose some accuracy and so make
unit testing more difficult than needs to be.
v10:
* Fix accounting for preemption.
v11:
* Rebase for i915_modparams.enable_execlists removal.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171121181852.16128-5-tvrtko.ursulin@linux.intel.com
From: Chris Wilson <chris@chris-wilson.co.uk>
From: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
From: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
The first goal is to be able to measure GPU (and invidual ring) busyness
without having to poll registers from userspace. (Which not only incurs
holding the forcewake lock indefinitely, perturbing the system, but also
runs the risk of hanging the machine.) As an alternative we can use the
perf event counter interface to sample the ring registers periodically
and send those results to userspace.
Functionality we are exporting to userspace is via the existing perf PMU
API and can be exercised via the existing tools. For example:
perf stat -a -e i915/rcs0-busy/ -I 1000
Will print the render engine busynnes once per second. All the performance
counters can be enumerated (perf list) and have their unit of measure
correctly reported in sysfs.
v1-v2 (Chris Wilson):
v2: Use a common timer for the ring sampling.
v3: (Tvrtko Ursulin)
* Decouple uAPI from i915 engine ids.
* Complete uAPI defines.
* Refactor some code to helpers for clarity.
* Skip sampling disabled engines.
* Expose counters in sysfs.
* Pass in fake regs to avoid null ptr deref in perf core.
* Convert to class/instance uAPI.
* Use shared driver code for rc6 residency, power and frequency.
v4: (Dmitry Rogozhkin)
* Register PMU with .task_ctx_nr=perf_invalid_context
* Expose cpumask for the PMU with the single CPU in the mask
* Properly support pmu->stop(): it should call pmu->read()
* Properly support pmu->del(): it should call stop(event, PERF_EF_UPDATE)
* Introduce refcounting of event subscriptions.
* Make pmu.busy_stats a refcounter to avoid busy stats going away
with some deleted event.
* Expose cpumask for i915 PMU to avoid multiple events creation of
the same type followed by counter aggregation by perf-stat.
* Track CPUs getting online/offline to migrate perf context. If (likely)
cpumask will initially set CPU0, CONFIG_BOOTPARAM_HOTPLUG_CPU0 will be
needed to see effect of CPU status tracking.
* End result is that only global events are supported and perf stat
works correctly.
* Deny perf driver level sampling - it is prohibited for uncore PMU.
v5: (Tvrtko Ursulin)
* Don't hardcode number of engine samplers.
* Rewrite event ref-counting for correctness and simplicity.
* Store initial counter value when starting already enabled events
to correctly report values to all listeners.
* Fix RC6 residency readout.
* Comments, GPL header.
v6:
* Add missing entry to v4 changelog.
* Fix accounting in CPU hotplug case by copying the approach from
arch/x86/events/intel/cstate.c. (Dmitry Rogozhkin)
v7:
* Log failure message only on failure.
* Remove CPU hotplug notification state on unregister.
v8:
* Fix error unwind on failed registration.
* Checkpatch cleanup.
v9:
* Drop the energy metric, it is available via intel_rapl_perf.
(Ville Syrjälä)
* Use HAS_RC6(p). (Chris Wilson)
* Handle unsupported non-engine events. (Dmitry Rogozhkin)
* Rebase for intel_rc6_residency_ns needing caller managed
runtime pm.
* Drop HAS_RC6 checks from the read callback since creating those
events will be rejected at init time already.
* Add counter units to sysfs so perf stat output is nicer.
* Cleanup the attribute tables for brevity and readability.
v10:
* Fixed queued accounting.
v11:
* Move intel_engine_lookup_user to intel_engine_cs.c
* Commit update. (Joonas Lahtinen)
v12:
* More accurate sampling. (Chris Wilson)
* Store and report frequency in MHz for better usability from
perf stat.
* Removed metrics: queued, interrupts, rc6 counters.
* Sample engine busyness based on seqno difference only
for less MMIO (and forcewake) on all platforms. (Chris Wilson)
v13:
* Comment spelling, use mul_u32_u32 to work around potential GCC
issue and somne code alignment changes. (Chris Wilson)
v14:
* Rebase.
v15:
* Rebase for RPS refactoring.
v16:
* Use the dynamic slot in the CPU hotplug state machine so that we are
free to setup our state as multi-instance. Previously we were re-using
the CPUHP_AP_PERF_X86_UNCORE_ONLINE slot which is neither used as
multi-instance, nor owned by our driver to start with.
* Register the CPU hotplug handlers after the PMU, otherwise the callback
will get called before the PMU is initialized which can end up in
perf_pmu_migrate_context with an un-initialized base.
* Added workaround for a probable bug in cpuhp core.
v17:
* Remove workaround for the cpuhp bug.
v18:
* Rebase for drm_i915_gem_engine_class getting upstream before us.
v19:
* Rebase. (trivial)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171121181852.16128-2-tvrtko.ursulin@linux.intel.com
Since removing the module parameter to force selection of ringbuffer
emission for gen8, the code is defunct. Remove it.
To put the difference into perspective, a couple of microbenchmarks
(bdw i7-5557u, 20170324):
ring execlists
exec continuous nops on all rings: 1.491us 2.223us
exec sequential nops on each ring: 12.508us 53.682us
single nop + sync: 9.272us 30.291us
vblank_mode=0 glxgears: ~11000fps ~9000fps
Since the earlier submission, gen8 ringbuffer submission has fallen
further and further behind in features. So while ringbuffer may hold the
throughput crown, in terms of interactive latency, execlists is much
better. Alas, we have no convenient metrics for such, other than
demonstrating things we can do with execlists but can not using
legacy ringbuffer submission.
We have made a few improvements to lowlevel execlists throughput,
and ringbuffer currently panics on boot! (bdw i7-5557u, 20171026):
ring execlists
exec continuous nops on all rings: n/a 1.921us
exec sequential nops on each ring: n/a 44.621us
single nop + sync: n/a 21.953us
vblank_mode=0 glxgears: n/a ~18500fps
References: https://bugs.freedesktop.org/show_bug.cgi?id=87725
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Once-upon-a-time-Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171120205504.21892-2-chris@chris-wilson.co.uk
The hardware needs some time to process the information received in the
ExecList Submission Port, and expects us to not write anything more until
it has 'acknowledged' this new submission by sending an IDLE_ACTIVE or
PREEMPTED CSB event.
If we do not follow this, the driver could write new data into the ELSP
before HW had finishing fetching the previous one, putting us in
'undefined behaviour' space.
This seems to be the problem causing the spurious PREEMPTED & COMPLETE
events after a COMPLETE like the one below:
[] vcs0: sw rd pointer = 2, hw wr pointer = 0, current 'head' = 3.
[] vcs0: Execlist CSB[0]: 0x00000018 _ 0x00000007
[] vcs0: Execlist CSB[1]: 0x00000001 _ 0x00000000
[] vcs0: Execlist CSB[2]: 0x00000018 _ 0x00000007 <<< COMPLETE
[] vcs0: Execlist CSB[3]: 0x00000012 _ 0x00000007 <<< PREEMPTED & COMPLETE
[] vcs0: Execlist CSB[4]: 0x00008002 _ 0x00000006
[] vcs0: Execlist CSB[5]: 0x00000014 _ 0x00000006
The ELSP writes that lead to this CSB sequence show that the HW hadn't
started executing the previous execlist (the one with only ctx 0x6) by the
time the new one was submitted; this is a bit more clear in the data
show in the EXECLIST_STATUS register at the time of the ELSP write.
[] vcs0: ELSP[0] = 0x0_0 [execlist1] - status_reg = 0x0_302
[] vcs0: ELSP[1] = 0x6_fedb2119 [execlist0] - status_reg = 0x0_8302
[] vcs0: ELSP[2] = 0x7_fedaf119 [execlist1] - status_reg = 0x0_8308
[] vcs0: ELSP[3] = 0x6_fedb2119 [execlist0] - status_reg = 0x7_8308
Note that having to wait for this ack does not disable lite-restores,
although it may reduce their numbers.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=102035
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/<20171118003038.7935-1-michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171120123458.23242-4-chris@chris-wilson.co.uk
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
intel_lrc_irq_handler and i915_guc_irq_handler are HW submission related
tasklet functions. Name them with "submission_tasklet" suffix and
remove intel/i915 prefix as they are static. Also rename irq_tasklet
as just tasklet for clarity.
v2: s/_bh/_tasklet (Chris)
Suggested-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1510839162-25197-2-git-send-email-sagar.a.kamble@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
At the start of building a request, we would wait for roughly enough
space to fit the average request (to reduce the likelihood of having to
wait and abort partway through request construction). To achieve we
would try to begin a 0-length command packet, this just adds extra
confusion so make the wait-for-space explicit, as in the next patch we
want to move it from the backend to the i915_gem_request_alloc() so it
can ensure that the wait-for-space is the first operation in building a
new request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115151204.8105-2-chris@chris-wilson.co.uk
As we now record the default HW state and so only emit the "golden"
renderstate once to prepare the HW, there is no advantage in keeping the
renderstate batch around as it will never be used again.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171110142634.10551-8-chris@chris-wilson.co.uk
