"skb" is non-NULL here, for example we dereference it in skb_clone().
The intent was to test "nskb" which was just set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In case of a client X roaming from a generic node A to another node B, it is
possible that a third node C gets A's OGM but not B's. At this point in time, if
C wants to send data to X it will send a unicast packet destined to A. The
packet header will contain A's last ttvn (C got A's OGM and so it knows it).
The packet will travel towards A without being intercepted because the ttvn
contained in its header is the newest for A.
Once A will receive the packet, A's state will not report to be in a "roaming
phase" (because, after a roaming, once A sends out its OGM, all the changes are
committed and the node is considered not to be in the roaming state anymore)
and it will match the ttvn carried by the packet. Therefore there is no reason
for A to try to alter the packet's route, thus dropping the packet because the
destination client is not there anymore.
However, C is well aware that it's routing information towards the client X is
outdated as it received an OGM from A saying that the client roamed away.
Thanks to this detail, this patch introduces a small change in behaviour: as
long as C is in the state of not knowing the new location of client X it will
forward the traffic to its last known location using ttvn-1 of the destination.
By using an older ttvn node A will be forced to re-route the packet.
Intermediate nodes are also allowed to update the packet's destination as long
as they have the information about the client's new location.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Whenever we want to access headers only, we do not need to linearise the whole
packet. Instead we can use pskb_may_pull()
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Pull networking fixes from David S. Miller:
1) Since we do RCU lookups on ipv4 FIB entries, we have to test if the
entry is dead before returning it to our caller.
2) openvswitch locking and packet validation fixes from Ansis Atteka,
Jesse Gross, and Pravin B Shelar.
3) Fix PM resume locking in IGB driver, from Benjamin Poirier.
4) Fix VLAN header handling in vhost-net and macvtap, from Basil Gor.
5) Revert a bogus network namespace isolation change that was causing
regressions on S390 networking devices.
6) If bonding decides to process and handle a LACPDU frame, we
shouldn't bump the rx_dropped counter. From Jiri Bohac.
7) Fix mis-calculation of available TX space in r8169 driver when doing
TSO, which can lead to crashes and/or hung device. From Julien
Ducourthial.
8) SCTP does not validate cached routes properly in all cases, from
Nicolas Dichtel.
9) Link status interrupt needs to be handled in ks8851 driver, from
Stephen Boyd.
10) Use capable(), not cap_raised(), in connector/userns netlink code.
From Eric W. Biederman via Andrew Morton.
11) Fix pktgen OOPS on module unload, from Eric Dumazet.
12) iwlwifi under-estimates SKB truesizes, also from Eric Dumazet.
13) Cure division by zero in SFC driver, from Ben Hutchings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ks8851: Update link status during link change interrupt
macvtap: restore vlan header on user read
vhost-net: fix handle_rx buffer size
bonding: don't increase rx_dropped after processing LACPDUs
connector/userns: replace netlink uses of cap_raised() with capable()
sctp: check cached dst before using it
pktgen: fix crash at module unload
Revert "net: maintain namespace isolation between vlan and real device"
ehea: fix losing of NEQ events when one event occurred early
igb: fix rtnl race in PM resume path
ipv4: Do not use dead fib_info entries.
r8169: fix unsigned int wraparound with TSO
sfc: Fix division by zero when using one RX channel and no SR-IOV
openvswitch: Validation of IPv6 set port action uses IPv4 header
net: compare_ether_addr[_64bits]() has no ordering
cdc_ether: Ignore bogus union descriptor for RNDIS devices
bnx2x: bug fix when loading after SAN boot
e1000: Silence sparse warnings by correcting type
igb, ixgbe: netdev_tx_reset_queue incorrectly called from tx init path
openvswitch: Release rtnl_lock if ovs_vport_cmd_build_info() failed.
...
af_inet6.c:80: ERROR: do not initialise statics to 0 or NULL
af_inet6.c:259: ERROR: spaces required around that '=' (ctx:VxV)
af_inet6.c:394: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:412: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:422: ERROR: do not use assignment in if condition
af_inet6.c:425: ERROR: do not use assignment in if condition
af_inet6.c:433: ERROR: do not use assignment in if condition
af_inet6.c:437: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:446: ERROR: spaces required around that '=' (ctx:VxV)
af_inet6.c:478: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:485: ERROR: that open brace { should be on the previous line
af_inet6.c:485: ERROR: space required before the open parenthesis '('
af_inet6.c:513: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:629: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:647: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:687: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:709: WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
af_inet6.c:1073: ERROR: space required before the open parenthesis '('
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
translation_table.{c,h} have been heavily modified by another contributor and
for legal purposes it is better to include his name into the contributor list
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
batman-adv would forward OGMs from non-besthops while replacing the the TQ
and TTL values with the values from the best hop. In certain corner cases
this leads to a temporary routing loop.
This patch changes this behavior: Only packets from best next hops are
forwarded - TQ and TTL values won't be replaced anymore. However, the protocol
needs to rebroadcast OGMs from single hop neighbors regardless of whether or
not they are the best hop. To handle this case a new flag is introduced to
alert neighboring nodes about the forwarded OGM that is not from my best
next hop. It is to be discarded by all nodes except for the one originating
the OGM.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Daniele Furlan <daniele.furlan@gmail.com>
Tested-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
This allows us to easily add a sysfs parameter for an unsigned int
later, which is not for a batman mesh interface (e.g. bat0), but for a
common interface instead. It allows reading and writing an atomic_t in
hard_iface (instead of bat_priv compared to the mesh variant).
Developed by Linus during a 6 months trainee study period in Ascom
(Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Reported-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Announce the (un)registration of a key type in the core key code rather than
in the callers.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The B.A.T.M.A.N. IV OGM receive function still was hard-coded although
it is a routing protocol specific function. This patch takes advantage
of the dynamic packet handler registration to remove the hard-coded
function calls.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The packet handler array replaces the growing switch statement, thus
dealing with incoming packets in a more efficient way. It also adds
to possibility to register packet handlers on the fly.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In is_type_dhcprequest(), while parsing a DHCP message, if the entry we found in
the option list is neither a padding nor the dhcp-type, we have to ignore it and
jump as many bytes as its length + 1. The "+ 1" byte is given by the subtype
field itself that has to be jumped too.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
According to the RFC4944 (Transmission of IPv6 Packets over
IEEE 802.15.4 Networks), chapter 7:
The IPv6 link-local address [RFC4291] for an IEEE 802.15.4 interface
is formed by appending the Interface Identifier, as defined above, to
the prefix FE80::/64.
10 bits 54 bits 64 bits
+----------+-----------------------+----------------------------+
|1111111010| (zeros) | Interface Identifier |
+----------+-----------------------+----------------------------+
This patch adds IPv6 address generation support for the 6lowpan
interfaces.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An implementation of CoDel AQM, from Kathleen Nichols and Van Jacobson.
http://queue.acm.org/detail.cfm?id=2209336
This AQM main input is no longer queue size in bytes or packets, but the
delay packets stay in (FIFO) queue.
As we don't have infinite memory, we still can drop packets in enqueue()
in case of massive load, but mean of CoDel is to drop packets in
dequeue(), using a control law based on two simple parameters :
target : target sojourn time (default 5ms)
interval : width of moving time window (default 100ms)
Based on initial work from Dave Taht.
Refactored to help future codel inclusion as a plugin for other linux
qdisc (FQ_CODEL, ...), like RED.
include/net/codel.h contains codel algorithm as close as possible than
Kathleen reference.
net/sched/sch_codel.c contains the linux qdisc specific glue.
Separate structures permit a memory efficient implementation of fq_codel
(to be sent as a separate work) : Each flow has its own struct
codel_vars.
timestamps are taken at enqueue() time with 1024 ns precision, allowing
a range of 2199 seconds in queue, and 100Gb links support. iproute2 uses
usec as base unit.
Selected packets are dropped, unless ECN is enabled and packets can get
ECN mark instead.
Tested from 2Mb to 10Gb speeds with no particular problems, on ixgbe and
tg3 drivers (BQL enabled).
Usage: tc qdisc ... codel [ limit PACKETS ] [ target TIME ]
[ interval TIME ] [ ecn ]
qdisc codel 10: parent 1:1 limit 2000p target 3.0ms interval 60.0ms ecn
Sent 13347099587 bytes 8815805 pkt (dropped 0, overlimits 0 requeues 0)
rate 202365Kbit 16708pps backlog 113550b 75p requeues 0
count 116 lastcount 98 ldelay 4.3ms dropping drop_next 816us
maxpacket 1514 ecn_mark 84399 drop_overlimit 0
CoDel must be seen as a base module, and should be used keeping in mind
there is still a FIFO queue. So a typical setup will probably need a
hierarchy of several qdiscs and packet classifiers to be able to meet
whatever constraints a user might have.
One possible example would be to use fq_codel, which combines Fair
Queueing and CoDel, in replacement of sfq / sfq_red.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
Cc: Kathleen Nichols <nichols@pollere.com>
Cc: Van Jacobson <van@pollere.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Class bytes/packets stats can be misleading because they are updated in
enqueue() while packet might be dropped later.
We already fixed all qdiscs but sch_atm.
This patch makes the final cleanup.
class rate estimators can now match qdisc ones.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal_64bits to add
some clarity and reduce the likelihood for misuse of
compare_ether_addr_64bits for sorting.
Done via cocci script:
$ cat compare_ether_addr_64bits.cocci
@@
expression a,b;
@@
- !compare_ether_addr_64bits(a, b)
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- compare_ether_addr_64bits(a, b)
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !ether_addr_equal_64bits(a, b) == 0
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !ether_addr_equal_64bits(a, b) != 0
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- ether_addr_equal_64bits(a, b) == 0
+ !ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- ether_addr_equal_64bits(a, b) != 0
+ ether_addr_equal_64bits(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal_64bits(a, b)
+ ether_addr_equal_64bits(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If enabled, L2TP data packets have sequence numbers which a receiver
can use to drop out of sequence frames or try to reorder them. The
first frame has sequence number 0, but the L2TP code currently expects
it to be 1. This results in the first data frame being handled as out
of sequence.
This one-line patch fixes the problem.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When L2TP data packet reordering is enabled, packets are held in a
queue while waiting for out-of-sequence packets. If a packet gets
lost, packets will be held until the reorder timeout expires, when we
are supposed to then advance to the sequence number of the next packet
but we don't currently do so. As a result, the data channel is stuck
because we are waiting for a packet that will never arrive - all
packets age out and none are passed.
The fix is to add a flag to the session context, which is set when the
reorder timeout expires and tells the receive code to reset the next
expected sequence number to that of the next packet in the queue.
Tested in a production L2TP network with Starent and Nortel L2TP gear.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As proposed by Eric, make the tcp_input.o thinner.
add/remove: 1/1 grow/shrink: 1/4 up/down: 868/-1329 (-461)
function old new delta
tcp_try_rmem_schedule - 864 +864
tcp_ack 4811 4815 +4
tcp_validate_incoming 817 815 -2
tcp_collapse 860 858 -2
tcp_send_rcvq 555 353 -202
tcp_data_queue 3435 3033 -402
tcp_prune_queue 721 - -721
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Eric, no checks are performed on the data size we're
putting in the read queue during repair. Thus, validate the given
data size with the common rmem management routine.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It actually works on the input queue and will use its read mem
routines, thus it's better to have in in the tcp_input.c file.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst_check() will take care of SA (and obsolete field), hence
IPsec rekeying scenario is taken into account.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vlad Yaseivch <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8a83a00b07.
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
Conflicts:
drivers/net/macvlan.c
net/8021q/vlan_dev.c
net/core/dev.c
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows comparing hash and len in one operation on 64-bit
architectures. Right now only __d_lookup_rcu() takes advantage of this,
since that is the case we care most about.
The use of anonymous struct/unions hides the alternate 64-bit approach
from most users, the exception being a few cases where we initialize a
'struct qstr' with a static initializer. This makes the problematic
cases use a new QSTR_INIT() helper function for that (but initializing
just the name pointer with a "{ .name = xyzzy }" initializer remains
valid, as does just copying another qstr structure).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to RCU lookups and RCU based release, fib_info objects can
be found during lookup which have fi->fib_dead set.
We must ignore these entries, otherwise we risk dereferencing
the parts of the entry which are being torn down.
Reported-by: Yevgen Pronenko <yevgen.pronenko@sonymobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix for the NFSv4 security negotiation:
- Ensure that the security negotiation tries all registered security flavours
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xNqW
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.4-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull a NFS client bugfix from Trond Myklebust:
"Fix for the NFSv4 security negotiation: ensure that the security
negotiation tries all registered security flavours"
* tag 'nfs-for-3.4-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
auth_gss: the list of pseudoflavors not being parsed correctly
ETHTOOL_GMODULEINFO returns a new struct ethtool_modinfo that will return the
type and size of plug-in module eeprom (such as SFP+) for parsing
by userland program.
ETHTOOL_GMODULEEEPROM returns the raw eeprom information
using the existing ethtool_eeprom structture to return the data
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We want to support reading module (SFP+, XFP, ...) EEPROMs as well as
NIC EEPROMs. They will need a different command number and driver
operation, but the structure and arguments will be the same and so we
can share most of the code here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spatch/coccinelle isn't perfect. It doesn't understand
__aligned(x) and doesn't convert functions it can't parse.
Convert the remaining compare_ether_addr uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
I removed a conversion from scan.c/cmp_bss_core
that appears to be a sorting function.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spatch/coccinelle isn't perfect. It doesn't understand
__aligned(x) and doesn't convert functions it can't parse.
Convert the remaining compare_ether_addr uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
can be used e.g. for ingress traffic policing or
to detect when a host/port consumes more bandwidth than expected.
This is done by optionally making cost to mean
"cost per 16-byte-chunk-of-data" instead of "cost per packet".
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
followup patch would bloat main match function too much.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The target allows you to create rules in the "raw" and "mangle" tables
which set the skbuff mark by means of hash calculation within a given
range. The nfmark can influence the routing method (see "Use netfilter
MARK value as routing key") and can also be used by other subsystems to
change their behaviour.
[ Part of this patch has been refactorized and modified by Pablo Neira Ayuso ]
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds the flags parameter to ipv6_find_hdr. This flags
allows us to:
* know if this is a fragment.
* stop at the AH header, so the information contained in that header
can be used for some specific packet handling.
This patch also adds the offset parameter for inspection of one
inner IPv6 header that is contained in error messages.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The dot1q ethertype number (0x8100) is embedded in the code, although
it is already defined in included headers.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Use more common code for ERTM and streaming mode segmentation and
transmission, and begin using skb control block data for delaying
extended or enhanced header generation until just before the packet is
transmitted. This code is also better suited for resegmentation,
which is needed when L2CAP links are reconfigured after an AMP channel
move.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
hlen has a fixed size of L2CAP_HDR_SIZE, use this instead.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth Low Energy support so far was disabled by default via
a module parameter. With this change the module parameter will be removed
and Low Energy is enabled by default.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
No one is using hci_le_ltk_neg_reply() in bluetooth subsystem.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
hlen - L2CAP_HDR_SIZE = 0, so we don't need to add them in the
calculation.
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In this API, we were using sizeof operator for an array
given as function argument, which is invalid.
However this API is not used anywhere.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Adding Code Aurora Forum copyright information due to significant
additions of code.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
L2CAP sockets contain a pointer to l2cap_chan that needs to be
reference counted in order to prevent a possible dangling pointer when
the channel is freed.
There were a few other cases where an l2cap_chan pointer on the stack
was dereferenced after a call to l2cap_chan_del. Those pointers are
also now reference counted.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
l2cap_get_chan_by_ident was not used, but didn't generate a compiler
warning because it was an inline function.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Structure members used by ERTM or streaming mode need to be
initialized when an ERTM or streaming mode link is configured. Some
duplicate code is also eliminated by moving in to the ERTM init
function.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
These values are now in the nested l2cap_ctrl struct.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
User-space pass the remote device address type to kernel through
struct sockaddr_l2 what makes the advertising useless. This patch
removes all advertising cache code.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In order to establish a LE connection we need the address type
information. User-space already pass this information to kernel
through struct sockaddr_l2.
This patch adds the dst_type parameter to l2cap_chan_connect so we
are able to pass the address type info from user-space down to
hci_conn layer.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the dst_type parameter to hci_connect function.
Instead of searching the address type in advertising cache, we
use the dst_type parameter to establish LE connections.
The dst_type is ignored for BR/EDR connection establishment.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the helper function bdaddr_to_le to hci_core, so it
can be used in mgmt.c and hci_conn.c.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since address type macros are not only related to Management
Interface anymore, it makes sense to rename the helper function
mgmt_to_le to bdaddr_to_le.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since address type macros are not only related to Management
Interface anymore, it makes sense to rename the helper function
link_to_mgmt to link_to_bdaddr.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves address type macros to bluetooth.h since they will be
used by management interface and Bluetooth socket interface. It also
replaces the macro prefix MGMT_ADDR_ by BDADDR_.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes unneeded variable assignments in hci_connect.
'sec_level' is already assigned to BT_SECURITY_LOW in hci_le_connect
and 'pending_sec_level' and 'auth_type' are assigned right after
if statement.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As most LE devices leave advertising mode when they enter the connected
state, we may want to "pass" that connection to other users.
The first user will be the pairing procedure, the connection is
established without an associated socket, after the pairing is
complete, userspace may want to discover via GATT what services the
newly bonded device has.
If userspace establishes the connection while the timeout still
hasn't expired, the connection will be re-used.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Tested-by: João Paulo Rechi Vita <jprvita@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The cid or psm and the source address might not be enough to uniquely
identify a global channel, especially when the source address is our
own.
For instance, when trying to communicate with two LE devices in master
mode, data received from the both devices is sent to the same socket.
Fix this by taking the destination address into account when choosing
the socket.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Tested-by: João Paulo Rechi Vita <jprvita@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
We allocate memory with kzalloc() so there is no need to call
memset(..., 0, ...) or similar.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We currently initialize locks, lists, works, etc. in hci_register_dev()
(hci_alloc_dev() was added later) which is bogus because an hdev is in an
invalid state if it is not registered.
This patch moves all memory initialization to hci_alloc_dev(). Device
registering and registration of sub-modules is still left in
hci_register_dev() as it belongs there.
The benefit is (despite cleaning up the code-base) we can now always be
sure that an hdev is a valid object and can be locked and worked on even
though it may not be registered.
This patch also reorders the initialization to be easier to understand.
First the memory is initialized, then all generic structures and as last
step the sub-init functions are called. This guarantees that all
dependencies are initialized in the right order and makes it also easier
to find a specific line. We previously initialized it in the same order as
the "struct hci_dev" is declared which seems pretty random.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
alloc() and register() (and free() and unregister()) are closely related
so move them more closely together. This will also allow to move
functionality from register() to alloc() without needing
forward-declarations.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SCO sockets are only identified by its address. So only allow one
SCO socket in listening state per address or BDADDR_ANY.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Checking the source address in SCO bind function will prevent from
having an incoming and outgoing SCO socket. However that might be
needed in case of multiple SCO connections on a single device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
When adding HCI devices hci_register_dev assigns the same name
hci1 for subsequently added AMP devices.
...
[ 6958.381886] sysfs: cannot create duplicate filename
'/devices/virtual/bluetooth/hci1
...
We assume id starts with the number we'll try to add the new device
and keep iterating until we find the proper place. The only difference
is we start with 0 for BR/EDR device and 1 for AMP devices (thus AMP
devices will never receive register as index 0). Then every hdev->id in
the _ordered_ list <= to the id we want we increment id and move the
variable head. In the end we'll have id as the first available one and
head is where you need to add hdev after to keep the list ordered.
Reported-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sco_conn_add is called from two places and always with status = 0.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Split the checks for sk->sk_state and sk->sk_type for SCO listen
sockets. This makes the code more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Split the checks for sk->sk_state and sk->sk_type for L2CAP listen
sockets. This makes the code more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
SMP Keys should only be distributeed when encryption is successful.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
It does make sense to print hdev name after allocation.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the address type while loading long term keys when BT is
switched on. Without this fix pairing is reinitated even though LTK
exists for remote device because of mismatch of address type.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove goto statements that do nothing else than jump to the next line
of code.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The function already fails if the given size is greater than the MTU, so
there is no need to consider that case afterwards.
Signed-off-by: Mikel Astiz <mikel.astiz.oss@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
The involved values are all unsigned and thus unsigned int should be
used instead of signed int. Assigning ~0 to a signed int results in -1,
which is confusing and error-prone, while the code is trying to set the
maximum value possible.
The code still works because the C standard defines that unsigned
comparison will be performed in these cases, when comparing an unsigned
int and a signed int.
Signed-off-by: Mikel Astiz <mikel.astiz.oss@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
These functions encode or decode ERTM control fields (extended or
enhanced) to or from the new l2cap_ctrl structure.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A sequence list is a data structure used to track frames that need to
be retransmitted, and frames that have been requested for
retransmission by the remote device. It can compactly represent a
list of sequence numbers within the ERTM transmit window. Memory for
the list is allocated once at connection time, and common operations
in ERTM are O(1).
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some parameters in L2CAP chan are set to default similar way in
socket based channels and A2MP channels. Adds common function which
sets all defaults.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
AMP Info will be used in Discovery Response.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch adds management connect failed event when LE Create Connection
Command fails to inform user space that LE Connection failed to get
established.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch prevents resetting of discovery type while stopping
discovery, since otherwise the wrong type might be send in case of
discovery failure. It also doesn't matter that we are "lazy" with
updating the type since it is anyway reset when starting discovery again
and it's not needed to know the current discovery state.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch removes the MGMT_ADDR_INVALID macro. If the address type
isn't LE, we consider it is BR/EDR type.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch updates the address type sent from kernel to management
interface of BlueZ while sending the Long Term Key.
Signed-off-by: Hemant Gupta <hemant.gupta@stericsson.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove zero initialization since channel is allocated with kzalloc
in l2cap_chan_create.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
For each kernel release where commands or events are added to the
management interface, the revision field should be increment by one.
The increment should only happen once per kernel release and not
for every command/event that gets added. The revision value is for
informational purposes only, but this simple policy would make any
future debugging a lot simple.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Following the separation if core and sock code this change avoid
manipulation of sk inside l2cap_chan_create().
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Remove sparse warnings below:
...
net/bluetooth/l2cap_core.c:302:6: warning: symbol '__l2cap_chan_add' was
not declared. Should it be static?
net/bluetooth/l2cap_core.c:351:6: warning: symbol 'l2cap_chan_add' was
not declared. Should it be static?
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch changes inquiry result function handlers so they ignore
inquiry result events if periodic inquiry is enabled.
Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch adds a HCI_PERIODIC_INQ check to start_discovery.
If periodic inquiry is enabled, we fail MGMT Start Discovery
command with MGMT_STATUS_BUSY code.
Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch adds the HCI_PERIODIC_INQ flag to dev_flags. This flag
tracks if periodic inquiry is enabled or not.
Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch adds a handler function to Periodic Inquiry command
complete event.
Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch does a trivial code refactoring in stop_discovery
function by using a switch statement instead of an if-return-else
approach.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
We should return -EALREADY in hci_cancel_inquiry since it is more
suitable than -EPERM error code.
Signed-off-by: Andre Guedes <aguedespe@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
Reply with MGMT_STATUS_INVALID_PARAMS when userspace is trying to set
source with out-of-scope value.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds LE support to MGMT stop discovery command. So,
now we are able to cancel LE discovery procedures (LE-only and
interleaved).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds to hci_core the hci_cancel_le_scan function which
should be used to cancel an ongoing LE scan.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix sparse warnings related to incorrect type in assignment and static
symbol. Also use const keyword. Warnings are shown below:
...
net/bluetooth/mgmt.c:305:28: warning: incorrect type in assignment
(different base types)
net/bluetooth/mgmt.c:305:28: expected unsigned short [usertype] *opcode
net/bluetooth/mgmt.c:305:28: got restricted __le16 *<noident>
...
net/bluetooth/mgmt.c:2609:3: warning: symbol 'mgmt_handlers' was not declared.
Should it be static?
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case the struct is already __packed, there is no need to use unaligned
access to the data. So just use __le16_to_cpu in these cases.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
opcode to be accessed is in le16 format so convert it
first to cpu byte order.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In L2CAP we use le16 format so change direction of conversion
from le16_to_cpu to cpu_to_le16.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Create Chan Rsp shall put result and status in le format.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
L2CAP channel id is used in host format in internal L2CAP code.
Fix sparse warnings about wrong endian conversion.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
cmd->len is in le format so convert it to host format before use.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ediv is already in little endian order.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case the struct is already __packed, there is no need to use
unaligned access to the data. So just use cpu_to_le16 or
__constant_cpu_to_le16 in these cases.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Device ID details need to be programmed into the kernel for every
controller at least once. So provide management command for this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Device ID information can be provided via Extended Inquiry Data
as well. If a valid source is present, then include it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Inquiry Response TX power tag should be added to the Extended
Inquiry Data (EIR) as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We initialize the "struct device" in hci_alloc_dev() for a long time now
so we can access hdev->dev.parent directly. Hence, we can drop the
temporary field hdev->parent which is used in no other place than
hci_add_sysfs().
SET_HCIDEV_DEV() is never called after registering a device by the
drivers so we do not overwrite internal device-state. Furthermore,
hdev->dev is initialized to 0 by kzalloc() inside hci_alloc_dev() so the
default behavior with dev.parent = NULL is kept.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In order to do interleaved discovery we should be in DISCOVERY_
FINDING state. Otherwise, discovery should be stopped.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
chan->psm is kept in __le16 format which was not always taken
into account. Fix several bugs related to extra conversion.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Value to be converted is already in __le32 format.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Correct type warnings reported by sparse to show that this
functions takes ediv argument in __le16 format.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Correct endian conversion reported by sparse
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch introduces a new mesh configuration parameter "ht_opmode" and will
allow user to check the current HT protection mode selected. Users could
configure the protection mode by the command "iw mesh_iface set mesh_param
mesh_ht_protection_mode=2". The default protection mode of mesh is set to
non-HT mixed mode.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we have protection enabled, allow non-HT and HT20 stations to peer
with HT40+/- stations. Peering is still disallowed for HT40+/- mismatch.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Section 9.23.3.5 of IEEE 80211s standard describes the protection rules for
HT mesh STA in a MBSS. Three HT protection modes are supported for now:
non-HT mixed mode - is selected if any non-HT peers are present in our MBSS.
20MHz-protection mode - is selected if all peers in our 20/40MHz MBSS support
HT and atleast one HT20 peer is present.
no-protection mode - is selected otherwise.
This is a limited implementation of 9.23.3.5, which only considers mesh peers
when determining the HT protection mode. Station's channel_type needs to be
maintained.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Reviewed-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the BSS table is organized in a RB tree, the BSSs need to be
comparable. This means that we must define a < and > operator to
the BSS object.
compare_ethr_addr isn't enough since it returns only a binary value.
Since Felix's
cfg80211: use compare_ether_addr on MAC addresses instead of memcmp
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSS table is corrupted: rb_find_bss can't find the bss.
As a result BSSes are duplicated in the BSS table, and we get stuck
while probing an AP before associating (in STA mode).
Change-Id: I85928756f4328028230832c1565ece7f412f3843
CC: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The signal and noise are forced to be positive since ethtool
deals in unsigned 64-bit values and this number should be human
readable. This gives easy access to some of the data formerly
exposed in the deprecated /proc/net/wireless file.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds hooks to call into the driver to get additional
stats for the ethtool API.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets ethtool print out stats related to stations
connected to the interface. Does not yet get stats
from the underlying driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a mesh peer indicates it is operating as 20MHz-only in its HT
operation IE, have the rate control algorithm respect this by disabling
the equivalent bit in the ieee80211_sta HT capabilities.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need the station rate info when inserting a new sta_info. The
patch "mac80211: refactor mesh peer initialization" wrongly assumed the
rate info could be applied after insertion. After further review, this
is clearly not the case.
This fixes a regression where HT parameters were not applied before
inserting the sta_info, causing performance degradation.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate control updation never be called on 2040 BSS change.
The station should update its rate control on receiving beacon
with different HT mode in the HT operation IE. Not doing so,
leads to sending frames with higher(ht40) rates whereas AP is
operating in lower mode (ht20).
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes ip_queue support which was marked as obsolete
years ago. The nfnetlink_queue modules provides more advanced
user-space packet queueing mechanism.
This patch also removes capability code included in SELinux that
refers to ip_queue. Otherwise, we break compilation.
Several warning has been sent regarding this to the mailing list
in the past month without anyone rising the hand to stop this
with some strong argument.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Explicit helper attachment via the CT target is broken with NAT
if non-standard ports are used. This problem was hidden behind
the automatic helper assignment routine. Thus, it becomes more
noticeable now that we can disable the automatic helper assignment
with Eric Leblond's:
9e8ac5a netfilter: nf_ct_helper: allow to disable automatic helper assignment
Basically, nf_conntrack_alter_reply asks for looking up the helper
up if NAT is enabled. Unfortunately, we don't have the conntrack
template at that point anymore.
Since we don't want to rely on the automatic helper assignment,
we can skip the second look-up and stick to the helper that was
attached by iptables. With the CT target, the user is in full
control of helper attachment, thus, the policy is to trust what
the user explicitly configures via iptables (no automatic magic
anymore).
Interestingly, this bug was hidden by the automatic helper look-up
code. But it can be easily trigger if you attach the helper in
a non-standard port, eg.
iptables -I PREROUTING -t raw -p tcp --dport 8888 \
-j CT --helper ftp
And you disabled the automatic helper assignment.
I added the IPS_HELPER_BIT that allows us to differenciate between
a helper that has been explicitly attached and those that have been
automatically assigned. I didn't come up with a better solution
(having backward compatibility in mind).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This refreshes the "timeout" attribute in existing expectations if one is
given.
The use case for this would be for userspace helpers to extend the lifetime
of the expectation when requested, as this is not possible right now
without deleting/recreating the expectation.
I use this specifically for forwarding DCERPC traffic through:
DCERPC has a port mapper daemon that chooses a (seemingly) random port for
future traffic to go to. We expect this traffic (with a reasonable
timeout), but sometimes the port mapper will tell the client to continue
using the same port. This allows us to extend the expectation accordingly.
Signed-off-by: Kelvie Wong <kelvie@ieee.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
To build ip_vs as a module sysctl_rmem_max and sysctl_wmem_max
needs to be exported.
The dependency was added by "ipvs: wakeup master thread" patch.
Signed-off-by: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol '__ipvs_proto_data_get' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Functions not referenced outside of a source file should be marked
static to prevent it from being exposed globally.
This quiets the sparse warnings:
warning: symbol 'ip_vs_ftp_init' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
cp->flags is marked volatile but ip_vs_bind_dest
can safely modify the flags, so save some CPU cycles by
using temp variable.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Allow master and backup servers to use many threads
for sync traffic. Add sysctl var "sync_ports" to define the
number of threads. Every thread will use single UDP port,
thread 0 will use the default port 8848 while last thread
will use port 8848+sync_ports-1.
The sync traffic for connections is scheduled to many
master threads based on the cp address but one connection is
always assigned to same thread to avoid reordering of the
sync messages.
Remove ip_vs_sync_switch_mode because this check
for sync mode change is still risky. Instead, check for mode
change under sync_buff_lock.
Make sure the backup socks do not block on reading.
Special thanks to Aleksey Chudov for helping in all tests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add two new sysctl vars to control the sync rate with the
main idea to reduce the rate for connection templates because
currently it depends on the packet rate for controlled connections.
This mechanism should be useful also for normal connections
with high traffic.
sync_refresh_period: in seconds, difference in reported connection
timer that triggers new sync message. It can be used to
avoid sync messages for the specified period (or half of
the connection timeout if it is lower) if connection state
is not changed from last sync.
sync_retries: integer, 0..3, defines sync retries with period of
sync_refresh_period/8. Useful to protect against loss of
sync messages.
Allow sysctl_sync_threshold to be used with
sysctl_sync_period=0, so that only single sync message is sent
if sync_refresh_period is also 0.
Add new field "sync_endtime" in connection structure to
hold the reported time when connection expires. The 2 lowest
bits will represent the retry count.
As the sysctl_sync_period now can be 0 use ACCESS_ONCE to
avoid division by zero.
Special thanks to Aleksey Chudov for being patient with me,
for his extensive reports and helping in all tests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
High rate of sync messages in master can lead to
overflowing the socket buffer and dropping the messages.
Fixed sleep of 1 second without wakeup events is not suitable
for loaded masters,
Use delayed_work to schedule sending for queued messages
and limit the delay to IPVS_SYNC_SEND_DELAY (20ms). This will
reduce the rate of wakeups but to avoid sending long bursts we
wakeup the master thread after IPVS_SYNC_WAKEUP_RATE (8) messages.
Add hard limit for the queued messages before sending
by using "sync_qlen_max" sysctl var. It defaults to 1/32 of
the memory pages but actually represents number of messages.
It will protect us from allocating large parts of memory
when the sending rate is lower than the queuing rate.
As suggested by Pablo, add new sysctl var
"sync_sock_size" to configure the SNDBUF (master) or
RCVBUF (slave) socket limit. Default value is 0 (preserve
system defaults).
Change the master thread to detect and block on
SNDBUF overflow, so that we do not drop messages when
the socket limit is low but the sync_qlen_max limit is
not reached. On ENOBUFS or other errors just drop the
messages.
Change master thread to enter TASK_INTERRUPTIBLE
state early, so that we do not miss wakeups due to messages or
kthread_should_stop event.
Thanks to Pablo Neira Ayuso for his valuable feedback!
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As the goal is to mirror the inactconns/activeconns
counters in the backup server, make sure the cp->flags are
updated even if cp is still not bound to dest. If cp->flags
are not updated ip_vs_bind_dest will rely only on the initial
flags when updating the counters. To avoid mistakes and
complicated checks for protocol state rely only on the
IP_VS_CONN_F_INACTIVE bit when updating the counters.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Tested-by: Aleksey Chudov <aleksey.chudov@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Initially, when the synced connection is created we
use the forwarding method provided by master but once we
bind to destination it can be changed. As result, we must
update the application and the transmitter.
As ip_vs_try_bind_dest is called always for connections
that require dest binding, there is no need to validate the
cp and dest pointers.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As the IP_VS_CONN_F_INACTIVE bit is properly set
in cp->flags for all kind of connections we do not need to
add special checks for synced connections when updating
the activeconns/inactconns counters for first time. Now
logic will look just like in ip_vs_unbind_dest.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As IP_VS_CONN_F_NOOUTPUT is derived from the
forwarding method we should get it from conn_flags just
like we do it for IP_VS_CONN_F_FWD_MASK bits when binding
to real server.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Use GFP_KERNEL instead of GFP_ATOMIC when registering an ipvs protocol.
This is safe since it will always run from a process context.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Schedulers are initialized and bound to services only
on commands.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
They are called only on initialization.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
if net.bridge.bridge-nf-filter-vlan-tagged sysctl is enabled, bridge
netfilter removes the vlan header temporarily and then feeds the packet
to ip(6)tables.
When the new "bridge-nf-pass-vlan-input-device" sysctl is on
(default off), then bridge netfilter will also set the
in-interface to the vlan interface; if such an interface exists.
This is needed to make iptables REDIRECT target work with
"vlan-on-top-of-bridge" setups and to allow use of "iptables -i" to
match the vlan device name.
Also update Documentation with current brnf default settings.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch allows you to disable automatic conntrack helper
lookup based on TCP/UDP ports, eg.
echo 0 > /proc/sys/net/netfilter/nf_conntrack_helper
[ Note: flows that already got a helper will keep using it even
if automatic helper assignment has been disabled ]
Once this behaviour has been disabled, you have to explicitly
use the iptables CT target to attach helper to flows.
There are good reasons to stop supporting automatic helper
assignment, for further information, please read:
http://www.netfilter.org/news.html#2012-04-03
This patch also adds one message to inform that automatic helper
assignment is deprecated and it will be removed soon (this is
spotted only once, with the first flow that gets a helper attached
to make it as less annoying as possible).
Signed-off-by: Eric Leblond <eric@regit.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* ret variable initialization removed as useless
* similar code strings concatenated and functions code
flow became more plain
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, struct mreq has not been recognized and it was worked with
as with struct in_addr. That means imr_multiaddr was copied to
imr_address. So do recognize struct mreq here and copy that correctly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kernel validates set TCP/UDP port actions, it looks at
the ports in the existing flow to make sure that the L4 header exists.
However, these actions always use the IPv4 version of the struct.
Following patch fixes this by checking for flow ip protocol first.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
If we get an error code from crush_do_rule(), print an error to the
console.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Fix the node weight lookup for tree buckets by using a correct accessor.
Reflects ceph.git commit d287ade5bcbdca82a3aef145b92924cf1e856733.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
These were used for the ill-fated forcefeed feature. Remove them.
Reflects ceph.git commit ebdf80edfecfbd5a842b71fbe5732857994380c1.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Remove forcefeed functionality from CRUSH. This is an ugly misfeature that
is mostly useless and unused. Remove it.
Reflects ceph.git commit ed974b5000f2851207d860a651809af4a1867942.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Conflicts:
net/ceph/crush/mapper.c
Use a temporary variable here to avoid repeated array lookups and clean up
the code a bit.
This reflects ceph.git commit 6b5be27634ad307b471a5bf0db85c4f5c834885f.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
If we get a map that doesn't make sense, error out or ignore the badness
instead of BUGging out. This reflects the ceph.git commits
9895f0bff7dc68e9b49b572613d242315fb11b6c and
8ded26472058d5205803f244c2f33cb6cb10de79.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
This small adjustment reflects a change that was made in ceph.git commit
af6a9f30696c900a2a8bd7ae24e8ed15fb4964bb, about 6 months ago. An N-1
search is not exhaustive. Fixed ceph.git bug #1594.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Move various types from int -> __u32 (or similar), and add const as
appropriate.
This reflects changes that have been present in the userland implementation
for some time.
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
This was an ill-conceived feature that has been removed from Ceph. Do
this gracefully:
- reject attempts to specify a preferred_osd via the ioctl
- stop exposing this information via virtual xattrs
- always fill in -1 for requests, in case we talk to an older server
- don't calculate preferred_osd placements/pgids
Reviewed-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
There are three Kconfig entries with "--- help ---" attributes, and over
2000 Kconfig entries with "---help---" attributes. Apparently the three
attributes with embedded spaces are valid. Still, I see little reason
for using this obscure variant. And replacing those three attributes
with the common variant makes grepping Kconfig files for help texts a
bit easier too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With the recent changes for how we compute the skb truesize it occurs to me
we are probably going to have a lot of calls to skb_end_pointer -
skb->head. Instead of running all over the place doing that it would make
more sense to just make it a separate inline skb_end_offset(skb) that way
we can return the correct value without having gcc having to do all the
optimization to cancel out skb->head - skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is now only one spot that actually uses "fastpath" there isn't
much point in carrying it. Instead we can just use a check for skb_cloned
to verify if we can perform the fast-path free for the head or not.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fast-path for pskb_expand_head contains a check where the size plus the
unaligned size of skb_shared_info is compared against the size of the data
buffer. This code path has two issues. First is the fact that after the
recent changes by Eric Dumazet to __alloc_skb and build_skb the shared info
is always placed in the optimal spot for a buffer size making this check
unnecessary. The second issue is the fact that the check doesn't take into
account the aligned size of shared info. As a result the code burns cycles
doing a memcpy with nothing actually being shifted.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In each remaining case the tty_lock is associated with a specific tty. This
means we can now lock on a per tty basis. We do need tty_lock_pair() for
the pty case. Uglier but still a step in the right direction.
[fixed up calls in 3 missing drivers - gregkh]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears some networks play bad games with the two bits reserved for
ECN. This can trigger false congestion notifications and very slow
transferts.
Since RFC 3168 (6.1.1) forbids SYN packets to carry CT bits, we can
disable TCP ECN negociation if it happens we receive mangled CT bits in
the SYN packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Perry Lorier <perryl@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Wilmer van der Gaast <wilmer@google.com>
Cc: Ankur Jain <jankur@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Dave Täht <dave.taht@bufferbloat.net>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPnb50AAoJEHm+PkMAQRiGAE0H/A4zFZIUGmF3miKPDYmejmrZ
oVDYxVAu6JHjHWhu8E3VsinvyVscowjV8dr15eSaQzmDmRkSHAnUQ+dB7Di7jLC2
MNopxsWjwyZ8zvvr3rFR76kjbWKk/1GYytnf7GPZLbJQzd51om2V/TY/6qkwiDSX
U8Tt7ihSgHAezefqEmWp2X/1pxDCEt+VFyn9vWpkhgdfM1iuzF39MbxSZAgqDQ/9
JJrBHFXhArqJguhENwL7OdDzkYqkdzlGtS0xgeY7qio2CzSXxZXK4svT6FFGA8Za
xlAaIvzslDniv3vR2ZKd6wzUwFHuynX222hNim3QMaYdXm012M+Nn1ufKYGFxI0=
=4d4w
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc5' into next
Linux 3.4-rc5
Merge to pull in prerequisite change for Smack:
86812bb0de
Requested by Casey.
This patch fixes a possible lock-up bug where rtnl_lock might not
get released.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Pull networking fixes from David Miller:
1) Transfer padding was wrong for full-speed USB in ASIX driver, fix
from Ingo van Lil.
2) Propagate the negative packet offset fix into the PowerPC BPF JIT.
From Jan Seiffert.
3) dl2k driver's private ioctls were letting unprivileged tasks make
MII writes and other ugly bits like that. Fix from Jeff Mahoney.
4) Fix TX VLAN and RX packet drops in ucc_geth, from Joakim Tjernlund.
5) OOPS and network namespace fixes in IPVS from Hans Schillstrom and
Julian Anastasov.
6) Fix races and sleeping in locked context bugs in drop_monitor, from
Neil Horman.
7) Fix link status indication in smsc95xx driver, from Paolo Pisati.
8) Fix bridge netfilter OOPS, from Peter Huang.
9) L2TP sendmsg can return on error conditions with the socket lock
held, oops. Fix from Sasha Levin.
10) udp_diag should return meaningful values for socket memory usage,
from Shan Wei.
11) Eric Dumazet is so awesome he gets his own section:
Socket memory cgroup code (I never should have applied those
patches, grumble...) made erroneous changes to
sk_sockets_allocated_read_positive(). It was changed to
use percpu_counter_sum_positive (which requires BH disabling)
instead of percpu_counter_read_positive (which does not).
Revert back to avoid crashes and lockdep warnings.
Adjust the default tcp_adv_win_scale and tcp_rmem[2] values
to fix throughput regressions. This is necessary as a result
of our more precise skb->truesize tracking.
Fix SKB leak in netem packet scheduler.
12) New device IDs for various bluetooth devices, from Manoj Iyer,
AceLan Kao, and Steven Harms.
13) Fix command completion race in ipw2200, from Stanislav Yakovlev.
14) Fix rtlwifi oops on unload, from Larry Finger.
15) Fix hard_mtu when adjusting hard_header_len in smsc95xx driver.
From Stephane Fillod.
16) ehea driver registers it's IRQ before all the necessary state is
setup, resulting in crashes. Fix from Thadeu Lima de Souza
Cascardo.
17) Fix PHY connection failures in davinci_emac driver, from Anatolij
Gustschin.
18) Missing break; in switch statement in bluetooth's
hci_cmd_complete_evt(). Fix from Szymon Janc.
19) Fix queue programming in iwlwifi, from Johannes Berg.
20) Interrupt throttling defaults not being actually programmed into the
hardware, fix from Jeff Kirsher and Ying Cai.
21) TLAN driver SKB encoding in descriptor busted on 64-bit, fix from
Benjamin Poirier.
22) Fix blind status block RX producer pointer deref in TG3 driver, from
Matt Carlson.
23) Promisc and multicast are busted on ehea, fixes from Thadeu Lima de
Souza Cascardo.
24) Fix crashes in 6lowpan, from Alexander Smirnov.
25) tcp_complete_cwr() needs to be careful to not rewind the CWND to
ssthresh if ssthresh has the "infinite" value. Fix from Yuchung
Cheng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
sungem: Fix WakeOnLan
tcp: change tcp_adv_win_scale and tcp_rmem[2]
net: l2tp: unlock socket lock before returning from l2tp_ip_sendmsg
drop_monitor: prevent init path from scheduling on the wrong cpu
usbnet: fix failure handling in usbnet_probe
usbnet: fix leak of transfer buffer of dev->interrupt
ucc_geth: Add 16 bytes to max TX frame for VLANs
net: ucc_geth, increase no. of HW RX descriptors
netem: fix possible skb leak
sky2: fix receive length error in mixed non-VLAN/VLAN traffic
sky2: propogate rx hash when packet is copied
net: fix two typos in skbuff.h
cxgb3: Don't call cxgb_vlan_mode until q locks are initialized
ixgbe: fix calling skb_put on nonlinear skb assertion bug
ixgbe: Fix a memory leak in IEEE DCB
igbvf: fix the bug when initializing the igbvf
smsc75xx: enable mac to detect speed/duplex from phy
smsc75xx: declare smsc75xx's MII as GMII capable
smsc75xx: fix phy interrupt acknowledge
smsc75xx: fix phy init reset loop
...
This patch adds support for a skb_head_is_locked helper function. It is
meant to be used any time we are considering transferring the head from
skb->head to a paged frag. If the head is locked it means we cannot remove
the head from the skb so it must be copied or we must take the skb as a
whole.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO is very optimistic in skb truesize estimates, only taking into
account the used part of fragments.
Be conservative, and use more precise computation, so that bloated GRO
skbs can be collapsed eventually.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gss_mech_list_pseudoflavors() parses a list of registered mechanisms.
On that list contains a list of pseudo flavors which was not being
parsed correctly, causing only the first pseudo flavor to be found.
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
These function are no longer needed replace them with their more useful equivalents.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
As a first step to converting struct cred to be all kuid_t and kgid_t
values convert the group values stored in group_info to always be
kgid_t values. Unless user namespaces are used this change should
have no effect.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
This change cleans up the last bits of tcp_try_coalesce so that we only
need one goto which jumps to the end of the function. The idea is to make
the code more readable by putting things in a linear order so that we start
execution at the top of the function, and end it at the bottom.
I also made a slight tweak to the code for handling frags when we are a
clone. Instead of making it an if (clone) loop else nr_frags = 0 I changed
the logic so that if (!clone) we just set the number of frags to 0 which
disables the for loop anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change reorders the code related to the use of an skb->head_frag so it
is placed before we check the rest of the frags. This allows the code to
read more linearly instead of like some sort of loop.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses several issues in the way we were tracking the
truesize in tcp_try_coalesce.
First it was using ksize which prevents us from having a 0 sized head frag
and getting a usable result. To resolve that this patch uses the end
pointer which is set based off either ksize, or the frag_size supplied in
build_skb. This allows us to compute the original truesize of the entire
buffer and remove that value leaving us with just what was added as pages.
The second issue was the use of skb->len if there is a mergeable head frag.
We should only need to remove the size of an data aligned sk_buff from our
current skb->truesize to compute the delta for a buffer with a reused head.
By using skb->len the value of truesize was being artificially reduced
which means that head frags could use more memory than buffers using
standard allocations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant ot prevent stealing the skb->head to use as a page in
the event that the skb->head was cloned. This allows the other clones to
track each other via shinfo->dataref.
Without this we break down to two methods for tracking the reference count,
one being dataref, the other being the page count. As a result it becomes
difficult to track how many references there are to skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend tcp coalescing implementing it from tcp_queue_rcv(), the main
receiver function when application is not blocked in recvmsg().
Function tcp_queue_rcv() is moved a bit to allow its call from
tcp_data_queue()
This gives good results especially if GRO could not kick, and if skb
head is a fragment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before stealing fragments or skb head, we must make sure skbs are not
cloned.
Alexander was worried about destination skb being cloned : In bridge
setups, a driver could be fooled if skb->data_len would not match skb
nr_frags.
If source skb is cloned, we must take references on pages instead.
Bug happened using tcpdump (if not using mmap())
Introduce kfree_skb_partial() helper to cleanup code.
Reported-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_adv_win_scale default value is 2, meaning we expect a good citizen
skb to have skb->len / skb->truesize ratio of 75% (3/4)
In 2.6 kernels we (mis)accounted for typical MSS=1460 frame :
1536 + 64 + 256 = 1856 'estimated truesize', and 1856 * 3/4 = 1392.
So these skbs were considered as not bloated.
With recent truesize fixes, a typical MSS=1460 frame truesize is now the
more precise :
2048 + 256 = 2304. But 2304 * 3/4 = 1728.
So these skb are not good citizen anymore, because 1460 < 1728
(GRO can escape this problem because it build skbs with a too low
truesize.)
This also means tcp advertises a too optimistic window for a given
allocated rcvspace : When receiving frames, sk_rmem_alloc can hit
sk_rcvbuf limit and we call tcp_prune_queue()/tcp_collapse() too often,
especially when application is slow to drain its receive queue or in
case of losses (netperf is fast, scp is slow). This is a major latency
source.
We should adjust the len/truesize ratio to 50% instead of 75%
This patch :
1) changes tcp_adv_win_scale default to 1 instead of 2
2) increase tcp_rmem[2] limit from 4MB to 6MB to take into account
better truesize tracking and to allow autotuning tcp receive window to
reach same value than before. Note that same amount of kernel memory is
consumed compared to 2.6 kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_ip_sendmsg could return without releasing socket lock, making it all the
way to userspace, and generating the following warning:
[ 130.891594] ================================================
[ 130.894569] [ BUG: lock held when returning to user space! ]
[ 130.897257] 3.4.0-rc5-next-20120501-sasha #104 Tainted: G W
[ 130.900336] ------------------------------------------------
[ 130.902996] trinity/8384 is leaving the kernel with locks still held!
[ 130.906106] 1 lock held by trinity/8384:
[ 130.907924] #0: (sk_lock-AF_INET){+.+.+.}, at: [<ffffffff82b9503f>] l2tp_ip_sendmsg+0x2f/0x550
Introduced by commit 2f16270 ("l2tp: Fix locking in l2tp_ip.c").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I just noticed after some recent updates, that the init path for the drop
monitor protocol has a minor error. drop monitor maintains a per cpu structure,
that gets initalized from a single cpu. Normally this is fine, as the protocol
isn't in use yet, but I recently made a change that causes a failed skb
allocation to reschedule itself . Given the current code, the implication is
that this workqueue reschedule will take place on the wrong cpu. If drop
monitor is used early during the boot process, its possible that two cpus will
access a single per-cpu structure in parallel, possibly leading to data
corruption.
This patch fixes the situation, by storing the cpu number that a given instance
of this per-cpu data should be accessed from. In the case of a need for a
reschedule, the cpu stored in the struct is assigned the rescheule, rather than
the currently executing cpu
Tested successfully by myself.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementing the advanced early retransmit (sysctl_tcp_early_retrans==2).
Delays the fast retransmit by an interval of RTT/4. We borrow the
RTO timer to implement the delay. If we receive another ACK or send
a new packet, the timer is cancelled and restored to original RTO
value offset by time elapsed. When the delayed-ER timer fires,
we enter fast recovery and perform fast retransmit.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements RFC 5827 early retransmit (ER) for TCP.
It reduces DUPACK threshold (dupthresh) if outstanding packets are
less than 4 to recover losses by fast recovery instead of timeout.
While the algorithm is simple, small but frequent network reordering
makes this feature dangerous: the connection repeatedly enter
false recovery and degrade performance. Therefore we implement
a mitigation suggested in the appendix of the RFC that delays
entering fast recovery by a small interval, i.e., RTT/4. Currently
ER is conservative and is disabled for the rest of the connection
after the first reordering event. A large scale web server
experiment on the performance impact of ER is summarized in
section 6 of the paper "Proportional Rate Reduction for TCP”,
IMC 2011. http://conferences.sigcomm.org/imc/2011/docs/p155.pdf
Note that Linux has a similar feature called THIN_DUPACK. The
differences are THIN_DUPACK do not mitigate reorderings and is only
used after slow start. Currently ER is disabled if THIN_DUPACK is
enabled. I would be happy to merge THIN_DUPACK feature with ER if
people think it's a good idea.
ER is enabled by sysctl_tcp_early_retrans:
0: Disables ER
1: Reduce dupthresh to packets_out - 1 when outstanding packets < 4.
2: (Default) reduce dupthresh like mode 1. In addition, delay
entering fast recovery by RTT/4.
Note: mode 2 is implemented in the third part of this patch series.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This a prepartion patch that refactors the code to enter recovery
into a new function tcp_enter_recovery(). It's needed to implement
the delayed fast retransmit in ER.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_checksum_help(skb) can return an error, we must free skb in this
case. qdisc_drop(skb, sch) can also be feeded with a NULL skb (if
skb_unshare() failed), so lets use this generic helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ECN (Explicit Congestion Notification) marking capability to netem
tc qdisc add dev eth0 root netem drop 0.5 ecn
Instead of dropping packets, try to ECN mark them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP or UDP stacks have big enough latencies that prefetching next
pointer is worth it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink API lets users create unmanaged L2TPv3 tunnels using
iproute2. Until now, a request to create an unmanaged L2TPv3 IP
encapsulation tunnel over IPv6 would be rejected with
EPROTONOSUPPORT. Now that l2tp_ip6 implements sockets for L2TP IP
encapsulation over IPv6, we can add support for that tunnel type.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2TPv3 defines an IP encapsulation packet format where data is carried
directly over IP (no UDP). The kernel already has support for L2TP IP
encapsulation over IPv4 (l2tp_ip). This patch introduces support for
L2TP IP encapsulation over IPv6.
The implementation is derived from ipv6/raw and ipv4/l2tp_ip.
Signed-off-by: Chris Elston <celston@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implementing other protocols on top of IPv6, such as L2TPv3's IP
encapsulation over ipv6, we'd like to call some IPv6 functions which
are not currently exported. This patch exports them.
Signed-off-by: Chris Elston <celston@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for unmanaged L2TPv3 tunnels over IPv6 using
the netlink API. We already support unmanaged L2TPv3 tunnels over
IPv4. A patch to iproute2 to make use of this feature will be
submitted separately.
Signed-off-by: Chris Elston <celston@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an L2TP tunnel uses IPv6, make sure the l2tp debugfs file shows the
IPv6 address correctly.
Signed-off-by: Chris Elston <celston@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userspace uses connect() to associate a pppol2tp socket with a tunnel
socket. This needs to allow the caller to supply the new IPv6
sockaddr_pppol2tp structures if IPv6 is used.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The l2tp_ip socket currently maintains packet/byte stats in its
private socket structure. But these counters aren't exposed to
userspace and so serve no purpose. The counters were also
smp-unsafe. So this patch just gets rid of the stats.
While here, change a couple of internal __u32 variables to u32.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the l2tp_ip code to make use of an existing ipv4 support function.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2TP uses 64-bit counters but since these are not updated atomically,
we need to make them safe for smp. This patch addresses that.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the hid drivers of the bus drivers to a common generic hid
driver, and make it a proper module. This ought to simplify device
handling moving forward.
Cc: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Devices that do not have a special driver are handled by the generic
driver. This patch does the same thing using device groups; Instead of
forcing a particular driver, the appropriate driver is picked up by
udev. As a consequence, one can now move a device from generic to
specific handling by a simple rebind. By adding a new device id to the
generic driver, the same thing can be done in reverse.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
__skb_splice_bits() can check if skb to be spliced has its skb->head
mapped to a page fragment, instead of a kmalloc() area.
If so we can avoid a copy of the skb head and get a reference on
underlying page.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP coalesce can check if skb to be merged has its skb->head mapped to a
page fragment, instead of a kmalloc() area.
We had to disable coalescing in this case, for performance reasons.
We 'upgrade' skb->head as a fragment in itself.
This reduces number of cache misses when user makes its copies, since a
less sk_buff are fetched.
This makes receive and ofo queues shorter and thus reduce cache line
misses in TCP stack.
This is a followup of patch "net: allow skb->head to be a page fragment"
Tested with tg3 nic, with GRO on or off. We can see "TCPRcvCoalesce"
counter being incremented.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO can check if skb to be merged has its skb->head mapped to a page
fragment, instead of a kmalloc() area.
We 'upgrade' skb->head as a fragment in itself
This avoids the frag_list fallback, and permits to build true GRO skb
(one sk_buff and up to 16 fragments), using less memory.
This reduces number of cache misses when user makes its copy, since a
single sk_buff is fetched.
This is a followup of patch "net: allow skb->head to be a page fragment"
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->head is currently allocated from kmalloc(). This is convenient but
has the drawback the data cannot be converted to a page fragment if
needed.
We have three spots were it hurts :
1) GRO aggregation
When a linear skb must be appended to another skb, GRO uses the
frag_list fallback, very inefficient since we keep all struct sk_buff
around. So drivers enabling GRO but delivering linear skbs to network
stack aren't enabling full GRO power.
2) splice(socket -> pipe).
We must copy the linear part to a page fragment.
This kind of defeats splice() purpose (zero copy claim)
3) TCP coalescing.
Recently introduced, this permits to group several contiguous segments
into a single skb. This shortens queue lengths and save kernel memory,
and greatly reduce probabilities of TCP collapses. This coalescing
doesnt work on linear skbs (or we would need to copy data, this would be
too slow)
Given all these issues, the following patch introduces the possibility
of having skb->head be a fragment in itself. We use a new skb flag,
skb->head_frag to carry this information.
build_skb() is changed to accept a frag_size argument. Drivers willing
to provide a page fragment instead of kmalloc() data will set a non zero
value, set to the fragment size.
Then, on situations we need to convert the skb head to a frag in itself,
we can check if skb->head_frag is set and avoid the copies or various
fallbacks we have.
This means drivers currently using frags could be updated to avoid the
current skb->head allocation and reduce their memory footprint (aka skb
truesize). (thats 512 or 1024 bytes saved per skb). This also makes
bpf/netfilter faster since the 'first frag' will be part of skb linear
part, no need to copy data.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the comment blocks are floating in limbo between two
functions, or between blocks of code. Delete the extra line
feeds between any comment and its associated following block
of code, to be consistent with the majority of the rest of
the kernel. Also delete trailing newlines at EOF and fix
a couple trivial typos in existing comments.
This is a 100% cosmetic change with no runtime impact. We get
rid of over 500 lines of non-code, and being blank line deletes,
they won't even show up as noise in git blame.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the cwnd reduction is done, ssthresh may be infinite
if TCP enters CWR via ECN or F-RTO. If cwnd is not undone, i.e.,
undo_marker is set, tcp_complete_cwr() falsely set cwnd to the
infinite ssthresh value. The correct operation is to keep cwnd
intact because it has been updated in ECN or F-RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately it seems that I didn't properly test the case of
an expired external querier in the recent multicast bridge series.
The setup of the timer in that case is completely broken and leads
to a NULL-pointer dereference. This patch fixes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
