We need to add mcasp l3 port ranges for mcasp to use a correct l3
data port address for dma. And we're also missing the optional clocks
that we have tagged with HWMOD_OPT_CLKS_NEEDED in omap_hwmod_7xx_data.c.
Note that for reading the module revision register HWMOD_OPT_CLKS_NEEDED
do not seem to be needed. So they could be probably directly managed
only by the mcasp driver, and then we could leave them out for the
interconnect target module.
Fixes: 4ed0dfe3cf ("ARM: dts: dra7: Move l4 child devices to probe
them with ti-sysc")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like I missed the ranges for am335x epwmss. Let's set it up the
same way as for am437x and dra7.
Fixes: 87fc89ced3 ("ARM: dts: am335x: Move l4 child devices to probe
them with ti-sysc")
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While reviewing the missing mcasp ranges I noticed omap4 hsi range
for gdd is wrong so let's fix it.
I'm not aware of any omap4 devices in mainline kernel though that use
hsi though.
Fixes: 84badc5ec5 ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier attempt to move am335x mcasp to probe with ti-sysc
interconnect target module caused audio to stop working and and
the dts changes were reverted by commit 5d2632a577 ("ARM: dts:
Revert am335x mcasp ti-sysc changes").
Turns out we were missing the l3 data port ranges for mcasp. This
caused mcasp dma to attempt to use wrong port address. So let's
try again essentially reverting the earlier revert and adding the
missing l3 data port ranges.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to add mcasp l3 port ranges for mcasp to use a correct l3
data port address for dma.
Fixes: d95adfd458 ("ARM: dts: am437x: Move l4 child devices to
probe them with ti-sysc")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hwmod parses the DT hierarchically from root to search for matching
ti,hwmod property. With the introduction of L4 data, we have two nodes
with the ti,hwmod = "gmac" declaration, and the hwmod core only matches
the first one found, which is the target-module one. This node incorrectly
dropped the ti,no-idle flag, which causes number of problems, like ignoring
errata i877, and also causing an intermittent boot failure on certain dra7
boards.
Fix the issue by moving the ti,no-idle flag to the proper node.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this McASP FIFO would constantly underflow. EDMA
test via dmatest works though.
Let's revert the change for now until we know the root cause.
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove unused parameter from HASH1 dmas property on stm32mp157c SoC.
Fixes: 1e726a40e0 ("ARM: dts: stm32: Add HASH support on stm32mp157c")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[Olof: Bug doesn't cause any harm, so shouldn't need stable backport]
Signed-off-by: Olof Johansson <olof@lixom.net>
There are close to 800 indivudal changesets in this branch again, which
feels like a lot. There are particularly many changes for the NVIDIA
Tegra platform this time, in fact more than it has seen in the two years
since the v4.9 merge window. Aside from this, it's been fairly normal,
with lots of changes going into Renesas R-CAR, NXP i.MX, Allwinner Sunxi,
Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5
is a minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core
Marvell Armada 8040 network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in
the BMC.
NXP i.MX usually sees a lot of new boards each release. This time there
we only add one minor variant: ConnectCore 6UL SBC Pro uses the same
SoM design as the ConnectCore 6UL SBC Express added later. However,
there is a new chip, the i.MX6ULZ, which is an even smaller variant
of the i.MX6ULL, with features removed. There is also support for the
reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute module
based on bcm2837, it was launched in early 2017 but only now added to
the kernel, both as 32-bit and as 64-bit files, as we tend to do for
Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time
are:
Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana
Pi M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit
Asus Tinker board, the model 'S' based on rk3288, and three now
boards based on the popular RK3399 chip:
ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
Rock960: https://www.96boards.org/product/rock960/
RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and
the RK3399 is the same chip used in several Chromebooks. Finally,
we get support for the PX30 (aka rk3326) chip, which is based on the
low-end 64-bit Cortex-A35 CPU core. So far, only the evaluation board
is supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is based
on the MT7622 WiFi router platform, and the first product I've seen with
a 64-bit Mediatek chip in that market: http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2),
another quad-core Cortex-A53 SoC, and its evaluation platform.
On the 32-bit side, we gain support for an actual end-user product,
the Endless Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform. This
chip is commonly known as the Snapdragon 835, and is used in high-end
phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the previously
added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the M3NULCB
Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing files,
the only board that gets added is the Toradex Colibri T20 on Colibri
Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the (formerly
Marvell) Berlin line of set-top-box chips used e.g. in the various Google
Chromecast. Only the .dtsi gets added at this point, no actual machines.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yaED
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
-----BEGIN PGP SIGNATURE-----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=Cc6D
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new dvb frontend driver: lnbh29
- new sensor drivers: imx319 and imx 355
- some old soc_camera driver renames to avoid conflict with new
drivers
- new i.MX Pixel Pipeline (PXP) mem-to-mem platform driver
- a new V4L2 frontend for the FWHT codec
- several other improvements, bug fixes, code cleanups, etc
* tag 'media/v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (289 commits)
media: rename soc_camera I2C drivers
media: cec: forgot to cancel delayed work
media: vivid: Support 480p for webcam capture
media: v4l2-tpg: fix kernel oops when enabling HFLIP and OSD
media: vivid: Add 16-bit bayer to format list
media: v4l2-tpg-core: Add 16-bit bayer
media: pvrusb2: replace `printk` with `pr_*`
media: venus: vdec: fix decoded data size
media: cx231xx: fix potential sign-extension overflow on large shift
media: dt-bindings: media: rcar_vin: add device tree support for r8a7744
media: isif: fix a NULL pointer dereference bug
media: exynos4-is: make const array config_ids static
media: cx23885: make const array addr_list static
media: ivtv: make const array addr_list static
media: bttv-input: make const array addr_list static
media: cx18: Don't check for address of video_dev
media: dw9807-vcm: Fix probe error handling
media: dw9714: Remove useless error message
media: dw9714: Fix error handling in probe function
media: cec: name for RC passthrough device does not need 'RC for'
...
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----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=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Pull ARM updates from Russell King:
"The main item in this pull request are the Spectre variant 1.1 fixes
from Julien Thierry.
A few other patches to improve various areas, and removal of some
obsolete mcount bits and a redundant kbuild conditional"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8802/1: Call syscall_trace_exit even when system call skipped
ARM: 8797/1: spectre-v1.1: harden __copy_to_user
ARM: 8796/1: spectre-v1,v1.1: provide helpers for address sanitization
ARM: 8795/1: spectre-v1.1: use put_user() for __put_user()
ARM: 8794/1: uaccess: Prevent speculative use of the current addr_limit
ARM: 8793/1: signal: replace __put_user_error with __put_user
ARM: 8792/1: oabi-compat: copy oabi events using __copy_to_user()
ARM: 8791/1: vfp: use __copy_to_user() when saving VFP state
ARM: 8790/1: signal: always use __copy_to_user to save iwmmxt context
ARM: 8789/1: signal: copy registers using __copy_to_user()
ARM: 8801/1: makefile: use ARMv3M mode for RiscPC
ARM: 8800/1: use choice for kernel unwinders
ARM: 8798/1: remove unnecessary KBUILD_SRC ifeq conditional
ARM: 8788/1: ftrace: remove old mcount support
ARM: 8786/1: Debug kernel copy by printing
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Note that we are not yet moving dss or wkup_m3, those will be moved
later after some related driver changes.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to
their proper location and enable probing using ti-sysc.
In general the first child device address range starts at range 0
from the ti-sysc interconnect target so the move involves adjusting
the child device reg properties for that.
In case of any regressions, problem devices can be reverted to probe
with legacy platform data as needed by moving them back and removing
the related interconnect target module node.
Note that we are not yet moving dss or wkup_m3, those will be moved
later after some related driver changes.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to commit 8f42cb7f64 ("ARM: dts: omap4: Add l4 interconnect
hierarchy and ti-sysc data"), let's add proper interconnect hierarchy
for l4 interconnect instances with the related ti-sysc interconnect
module data as in Documentation/devicetree/bindings/bus/ti-sysc.txt.
Using ti-sysc driver binding allows us to start dropping legacy platform
data in arch/arm/mach-omap2/omap*hwmod*data.c files later on in favor of
ti-sysc dts data.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that we cannot yet include this file from the SoC dtsi file until
the child devices are moved to their proper locations in the
interconnect hierarchy in the following patch. Otherwise we would have
the each module probed twice.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert DRA7xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM isntance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert AM43xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM isntance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert AM33xx to use the new clockdomain based layout. Previously the
clkctrl split was based on CM instance boundaries. The new layout
helps with introducing the interconnect driver instances.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Two last minute bugfixes, both for NXP platforms:
* The Layerscape 'qbman' infrastructure suffers from probe ordering
bugs in some configurations, a two-patch series adds a hotfix for
this. 4.20 will have a longer set of patches to rework it.
* The old imx53-qsb board regressed in 4.19 after the addition
of cpufreq support, adding a set of explicit operating points
fixes this.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WY74
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Arnd writes:
"ARM: SoC fixes for 4.19
Two last minute bugfixes, both for NXP platforms:
* The Layerscape 'qbman' infrastructure suffers from probe ordering
bugs in some configurations, a two-patch series adds a hotfix for
this. 4.20 will have a longer set of patches to rework it.
* The old imx53-qsb board regressed in 4.19 after the addition
of cpufreq support, adding a set of explicit operating points
fixes this."
* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
ARM: dts: imx53-qsb: disable 1.2GHz OPP
Not all boards use two ethernet devices and/or use them in different
order. As almost all in-tree boards already define their own ethernet
aliases, remove them from the dtsi and add the aliases to the two boards,
that are missing their own definition.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[dinguyen@kernel.org: rebased to latest dts changes]
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Auto-detect nand ECC on the armada-385 based board db-88f6820-amc
instead of hard coded them in the device tree.
-----BEGIN PGP SIGNATURE-----
iFwEABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW7Y3KgAKCRALBhiOFHI7
1UBvAJiH2KUDbW343DFDnrUsePLsvZQRAJ9WcERzrI5pWPm+m1ix0Gj7Kp1L8g==
=FOy5
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.20-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.20 (part 2)
Auto-detect nand ECC on the armada-385 based board db-88f6820-amc
instead of hard coded them in the device tree.
* tag 'mvebu-dt-4.20-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is required for the imx pci driver to send the PME_Turn_Off TLP.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
As the v4l2-fwnode now allows drivers to set defaults, and eventually
override them by specifying properties in DTS, use defaults for the CEU
driver.
Also remove endpoint properties from the gr-peach-audiocamerashield as
they match the defaults now specified in the driver code
(h/vsync-active and bus-width) or are not relevant to the interface
as they cannot be configured (pclk-sample).
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
- Fix crash of qman_portal by deferring its probe if qman is not probed
-----BEGIN PGP SIGNATURE-----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=qVf2
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-fix-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into fixes
NXP/FSL SoC driver fixes for v4.19 round 2
- Fix crash of qman_portal by deferring its probe if qman is not probed
* tag 'soc-fsl-fix-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
soc: fsl: qe: Fix copy/paste bug in ucc_get_tdm_sync_shift()
soc: fsl: qbman: qman: avoid allocating from non existing gen_pool
ARM: dts: BCM63xx: Fix incorrect interrupt specifiers
MAINTAINERS: update the Annapurna Labs maintainer email
ARM: dts: sun8i: drop A64 HDMI PHY fallback compatible from R40 DT
ARM: dts: at91: sama5d2_ptc_ek: fix nand pinctrl
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This board has a Micron MT29F8G08ABACAWP chip which requires a ECC
strength of 8/512. Rather than hard coding any particular strength the
the nand controller auto-detect the ECC strength based on the ONFI data.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
- i.MX53 QSB board stops working when cpufreq driver is enabled,
because the default OPP table has the maximum CPU frequency at
1.2GHz, while the board is only capable of running 1GHz. Fix up
the OPP table for the board to get it work with cpufreq driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbtCuVAAoJEFBXWFqHsHzOHDEH/RXzkCIZCmvVhdXIQDa/PC7b
GupBi+UJE2iQMS3Z3RNYnZQ2yK8zq7AZNIjZtR7/8dm6ALFjXMGvfj19Cs0wThdt
VQ3g7FyS76lwvb2sVl6yGZTOcZfn7nIwFC9NNfY1FSt87QXKBPG0UmnMpCxR7m+1
V1d0T3y0WejpRigtzGJZJwibkOFoKy8HbAn09BBzyE+eRnNcXSp6NunIr+82AGgo
yA3rtcoDXD997wXMUUgnFzh0VjqH5wrrbMtplWOFpDtKEFxwiHGOjWsIm6S2xi/8
SKkk13M+GBHtPR0ygTtRngV1TF0z0kTdArhS/GGGTzWbpZ5sri5khyCfNP+i0LA=
=xyJS
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.19, round 2:
- i.MX53 QSB board stops working when cpufreq driver is enabled,
because the default OPP table has the maximum CPU frequency at
1.2GHz, while the board is only capable of running 1GHz. Fix up
the OPP table for the board to get it work with cpufreq driver.
* tag 'imx-fixes-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx53-qsb: disable 1.2GHz OPP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
----------------------------
- A non-critical fix to reduce errors on A/DC on Lego Mindstorms EV3
- Support for GPIO expander on DA850 EVM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVmP
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.20/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
DaVinci DT updates for v4.20
----------------------------
- A non-critical fix to reduce errors on A/DC on Lego Mindstorms EV3
- Support for GPIO expander on DA850 EVM
* tag 'davinci-for-v4.20/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dtc warning, gpio setting for the sdmmc regulator on radxarock and a
new board the "S" variant of the rk3288-based Tinker board, that sports
an added emmc.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAluyKz0QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgSxkB/9hXQysAvkRD0oCsBhRpRse/XkE99IyqoFD
QixXrUVdO21P5h/x0seJoqVE/dFrl2iQUBhgL9jyRHEZGPoTbZw0KoSe50KwGQp4
WkMqj9MukWdM11HDmonaQR+CcyoOkZHhWjGHuSIUSJKWi8wugVzL/X9IzHd7VdqB
TZ6DDnFqbxOsCMDw4jcPIRMO/wkePR7g3sL3u+Wn/9owsfho4pvP+kX/b8DOwS1N
mI30Ga+0O19XtGx3psc+xh7PSjKbw5UzVFz7EtHgeQHl0YjYUGh+RRf4nJmg17+T
YfxzVuvFLol6cKITI+iU5CGaJdazR1cThekCEyxFMHXlLIlxogLq
=MloN
-----END PGP SIGNATURE-----
Merge tag 'v4.20-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Nodes for the newly support rk3188 display controller, a fix for a new
dtc warning, gpio setting for the sdmmc regulator on radxarock and a
new board the "S" variant of the rk3288-based Tinker board, that sports
an added emmc.
* tag 'v4.20-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add rk3288-based Tinker board S
ARM: dts: rockchip: move shared tinker-board nodes to a common dtsi
ARM: dts: rockchip: explicitly set vcc_sd0 pin to gpio on rk3188-radxarock
ARM: dts: rockchip: Fix erroneous SPI bus dtc warnings on rk3036
ARM: dts: rockchip: add rk3188 lcd controller nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Due to the electrical design of the A/DC circuits on LEGO MINDSTORMS EV3,
if we are reading analog values as fast as possible (i.e. using DMA to
service the SPI) the A/DC chip will read incorrect values - as much as
0.1V off when the SPI is running at 10MHz. (This has to do with the
capacitor charge time when channels are muxed in the A/DC.)
This patch slows down the SPI as much as possible (if CPU is at 456MHz,
SPI runs at 1/2 of that, so 228MHz and has a max prescalar of 256, so
we could get ~891kHz, but we're just rounding it to 1MHz). We also use
the max allowable value for WDELAY to slow things down even more.
These changes reduce the error of the analog values to about 5mV, which
is tolerable.
Commits a3762b13a5 ("spi: spi-davinci: Add support for SPI_CS_WORD")
and e2540da86e ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") introduce changes that allow DMA transfers to be used, so
this slow down is needed now.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There is a GPIO expander on both the UI board as well as the
baseboard. This patch enables the second tca6416 and identifies
it as being on the baseboard using _bb as the suffix.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There's a patch for previously merged dts changes to remove the last
remaining use of legacy phy_id property.
For dra7, we have a non-urgent PCIe dts fix, enable a PCIe errata for
unaligned access.
For omap5, we enable omap5 USB OTG mode for DWC3 controller.
And we add support for am335x based Moxa UC-2100 series of industrial
computers.
-----BEGIN PGP SIGNATURE-----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=EQcw
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.20/dt-signed-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
More devicetree changes for omap variants
There's a patch for previously merged dts changes to remove the last
remaining use of legacy phy_id property.
For dra7, we have a non-urgent PCIe dts fix, enable a PCIe errata for
unaligned access.
For omap5, we enable omap5 USB OTG mode for DWC3 controller.
And we add support for am335x based Moxa UC-2100 series of industrial
computers.
* tag 'omap-for-v4.20/dt-signed-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x: Replace remaining legacy phy_id with phy-handle
ARM: dts: am335x: add support for Moxa UC-2101 open platform
ARM: dts: am335x: add common file for UC-2100 series
ARM: dts: omap5: enable OTG role for DWC3 controller
ARM: dts: dra7: Enable workaround for errata i870 in PCIe host mode
ARM: dts: dra7: Fix up unaligned access setting for PCIe EP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for Pro4, PXs2 and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
sama5d4_xplained, ssam9x5cm, sama5d2_ptc_ek and sama5d3_xplained nand
flashes have a common memory map. Even the nand memory partitions to
match our NAND flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
sama5d3_xplained, sam9x5cm, sama5d2_ptc_ek and sama5d4_xplained nand
flashes have a common memory map. Even the nand memory partitions to
match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
sam9x5cm, sama5d2_ptc_ek, sama5d3_xplained and sama5d4_xplained nand
flashes have a common memory map. Even the nand memory partitions to
match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
