This patch also includes the required removal of (unused) inclusion of
<asm/a.out.h> <linux/a.out.h>'s in the arch/ code for these
architectures.
[dwmw2: updated for 2.6.27-rc]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using just 'unsigned' will make flags an unsigned int. While this is
arguably not an error on blackfin where sizeof(int) == sizeof(long),
the patch is still justified on the grounds of principle.
The patch was generated using the Coccinelle semantic patch framework.
Cc: Julia Lawall <julia@diku.dk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
AFAIR there exists blackfin hardware with PCI support, but the support
currently in the kernel fails to build starting with:
...
CC drivers/pci/probe.o
probe.c: In function 'pci_scan_slot':
probe.c:1056: error: implicit declaration of function 'pcibios_scan_all_fns'
make[3]: *** [drivers/pci/probe.o] Error 1
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- remove cheesy read_iloc() function
- move invalidate_entire_icache function to lock.S
- export proper prototypes for functions in lock.S
- only build lock.S when BFIN_ICACHE_LOCK is enabled
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
as pointed out by Michael McTernan in the forums, when expanding
the trace buffer, it does not print out the decoded instruction.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- Disable all bits in SIC_IWR unless we are going into a real (DPMC)
power saving mode. Any Interrupt can wake the core form it's idle state.
- Remove deep sleep mode as it is not going to be used anywhere:
We support sleep, sleep deeper and hibernate.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- Skip single step if global interrupt disable bit is set.
- Extend bernds' patch r4673 to skip single step in any interrupt entry
that interrupts the code which is under single stepping. Bernds' patch
only allow user space single stepping.
Singed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
these are highly board specific, so putting into generic doesnt make much sense
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (30 commits)
Blackfin arch: If we double fault, rather than hang forever, reset
Blackfin arch: When icache is off, make sure people know it
Blackfin arch: Fix bug - skip single step in high priority interrupt handler instead of disabling all interrupts in single step debugging.
Blackfin arch: cache the values of vco/sclk/cclk as the overhead of doing so (~24 bytes) is worth avoiding the software mult/div routines
Blackfin arch: fix bug - IMDMA is not type struct dma_register
Blackfin arch: check the EXTBANKS field of the DDRCTL1 register to see if we are using both memory banks
Blackfin arch: Apply Bluetechnix CM-BF527 board support patch
Blackfin arch: Add unwinding for stack info, and a little more detail on trace buffer
Blackfin arch: Add ISP1760 board resources to BF548-EZKIT
Blackfin arch: fix bug - detect 0.1 silicon revision BF527-EZKIT as 0.0 version
Blackfin arch: add missing IORESOURCE_MEM flags to UART3
Blackfin arch: Add return value check in bfin_sir_probe(), remove SSYNC().
Blackfin arch: Extend sram malloc to handle L2 SRAM.
Blackfin arch: Remove useless config option.
Blackfin arch: change L1 malloc to base on slab cache and lists.
Blackfin arch: use local labels and ENDPROC() markings
Blackfin arch: Do not need this dualcore test module in kernel.
Blackfin arch: Allow ptrace to peek and poke application data in L1 data SRAM.
Blackfin arch: Add ANOMALY_05000368 workaround
Blackfin arch: Functional power management support
...
Remove arch-specific show_mem() in favor of the generic version.
This also removes the following redundant information display:
- free pages, printed by show_free_areas()
- pages in swapcache, printed by show_swap_cache_info()
where show_mem() calls show_free_areas(), which calls
show_swap_cache_info().
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Skip single step if event priority of current instruction is higher than
that of the first instruction, from which gdb starts single step.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
Also includes a few Kconfig files (xtensa, blackfin)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Remove the sram piece limitation and improve the performance to
alloc/free sram piece data.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Enable: PM_SUSPEND_MEM -> Blackfin Hibernate to SDRAM
This feature requires a special bootloader (u-boot)
supporting return from hibernate.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
use kernel command line mem and max_mem bootargs to limit
availabe memory instead.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Don't write conflicting data to EBIU_SDBCTL after the SDRAM is
configured. This can cause data corruption, since we might change SDRAM
row and column addressing modes.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
--
WARNING: vmlinux.o(.text+0x721a): Section mismatch in reference from the function ___fill_code_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_code_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_code_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.
WARNING: vmlinux.o(.text+0x7238): Section mismatch in reference from the function ___fill_code_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_code_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_code_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.
WARNING: vmlinux.o(.text+0x7250): Section mismatch in reference from the function ___fill_code_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_code_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_code_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.
WARNING: vmlinux.o(.text+0x7264): Section mismatch in reference from the function ___fill_code_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_code_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_code_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.
WARNING: vmlinux.o(.text+0x72a2): Section mismatch in reference from the function ___fill_data_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_data_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_data_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.
WARNING: vmlinux.o(.text+0x72bc): Section mismatch in reference from the function ___fill_data_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_data_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_data_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.
WARNING: vmlinux.o(.text+0x72d4): Section mismatch in reference from the function ___fill_data_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_data_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_data_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.
WARNING: vmlinux.o(.text+0x72e8): Section mismatch in reference from the function ___fill_data_cplbtab() to the function .init.text:_fill_cplbtab()
The function ___fill_data_cplbtab() references
the function __init _fill_cplbtab().
This is often because ___fill_data_cplbtab lacks a __init
annotation or the annotation of _fill_cplbtab is wrong.
--
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Initialize the lock of bad_irq_desc properly.
The content of irq_desc array is replaced by bad_irq_desc in blackfin
arch irqchip init code. So, do it properly as common irq init code.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The dm9000 driver accepts either 2 or 3 resources to describe the platform
devices. The 2 resources case abuses the ioresource mechanism by passing
ioremap()ed memory through the platform device resources. This patch removes
converts boards that were using it to the 3 resources scheme.
CC: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
AD7877 use SSEL_2 (P9.9) and IRQ_PF8 (P9.14) on BF527
- populating JP3 to enable STAMP
- disable SW11.2 to disconnect SSEL_2/PF12 from Rotary NAND
- disable SW18.1 to disconnect SSEL_2 from MAX1233 touchscreen chip
Signed-off-by: Bryan Wu <cooloney@kernel.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] return to old errno choice in mkdir() et.al.
[Patch] fs/binfmt_elf.c: fix wrong return values
[PATCH] get rid of leak in compat_execve()
[Patch] fs/binfmt_elf.c: fix a wrong free
[PATCH] avoid multiplication overflows and signedness issues for max_fds
[PATCH] dup_fd() part 4 - race fix
[PATCH] dup_fd() - part 3
[PATCH] dup_fd() part 2
[PATCH] dup_fd() fixes, part 1
[PATCH] take init_files to fs/file.c
I2C_BOARD_INFO() now sets the type field so no need to set it
separatetly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Bryan Wu <cooloney@kernel.org>
support two cascaded AD73322 cards, more uncached DMA
memory is needed, so add a choice to provide 4M DMA memory
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
so that we always send the same signal and we handle the NULL ptr condition properly
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
IMDMA does not operate to full speed for 600MHz and higher devices
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- move all kconfig board settings into board resources
- fixup casting style according to lkml feedback
- rewrite driver so that it can handle arbitrary
of instances according to the declared platform resources
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Cc: Joern Engel <joern@logfs.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
FSVOtest in this case, since I don't have the hardware...
However, all changes seen by gcc are actually
- explicit cast to unsigned short in return expression of functions
returning unsigned short
- csum_fold() return type changed from unsigned int to __sum16
(unsigned short), same as for all other architecture and as net/* expects;
expression actually returned is ((~(sum << 16)) >> 16) with sum being
unsigned 32bit, so it's (a) going to fit into the range of unsigned short
and (b) had been unsigned all along, so no sign expansion mess happened.
Tested-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Miller <davem@davemloft.net>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Remove module will not free L1 memory used which caused by
memory access after free. This patch fixes it.
Signed-off-by: Meihui Fan <mhfan@hhcn.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
When transferring to IRQ5 from an exception, save SYSCFG in memory across the
transfer and clear the trace bit.
When we get a single step exception, check whether we can safely clear the
trace bit in SYSCFG. We can (and should) clear it after the first instruction
of the interrupt handler; the first insn saves SYSCFG to the stack in all
handlers.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
When delivering a signal, disable single stepping but call
ptrace_notify if it was enabled before. The idea was taken
from the x86 port.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Fix some really ancient code that was correct only for the m68k port.
Delete unused (i.e. copied from m68k) entries in asm-offsets.c.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
In the double fault handler, set up the PT_RETI slot so that
we print out the correct return address in the dumping code.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The following cleanup patch:
add __user markings to a few userspace system functions
mysteriously added a "&" operator that doesn't belong in there, breaking the
atomic sections code.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
This replaces the duplicated arch-specific versions of "sys_pipe()" with
one unified implementation. This removes almost 250 lines of duplicated
code.
It's marked __weak, so that *if* an architecture wants to override the
default implementation it can do so by simply having its own replacement
version, since many architectures use alternate calling conventions for
the 'pipe()' system call for legacy reasons (ie traditional UNIX
implementations often return the two file descriptors in registers)
I still haven't changed the cris version even though Linus says the BKL
isn't needed. The arch maintainer can easily do it if there are really
no obstacles.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Remove the circular buffering mechanism for exceptions. Instead, point RETX
at a safe location from which to fetch three NOPs.
This safe location is now in the fixed code area, and also used for certain
anomaly workarounds, to ensure that user space can find a valid ICPLB when
things are built with CONFIG_MPU.
Also, save I/DCPLB_FAULT_ADDRESS when lowering to level 5, since the hardware
reg is valid only at exception level.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- add platform device resources in board files
- add new bfin_sir.h to each machines
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The irq setup code no longer calls gpio request and free.
This patch also changes the default gpio_free behavior on Blackfin.
A freed GPIO keeps it's last state, and is not defaulted back to
an input. This is also what all other architectures do.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
detect the memory available in the system on the fly by default
rather than forcing people to set this manually in the kconfig
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3978
Section data_l1_cacheline_aligned should be defined in
link script of kernel, when L1 data sram bank A is not available.
In bf536 with all data cache is enabled, there is no L1 data sram.
Current link script won't define section data_l1.cacheline_aligned in
this case. But, if user select put cacheline_aligned data into l1 sram
in kernel menuconfig, these data will be dropped and access to these
data will trigger data CPLB exception.
Do panic in l1 relocation code as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- allow bootrom to be readable from supervisor mode
- delete unused local variable "addr"
- punt unused local defines of cplbinfo.c
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The DMA base registers are available in a global named "base_addr" for
every Blackfin variant. Give this a more descriptive name, and remove
duplicate tables from some drivers.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
theres no need to declare ram{end,start,base} in the head.S files
when declaring them with the other memory related variables in setup.c
is so much simpler/nicer
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
remove duplicated prototypes for internal cplb structures from
the global blackfin header as nothing else should be accessing these
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
