Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
Both phy-tegra-usb.c and ehci-tegra.c export symbols used by the other one,
which does not work if one of them or both are loadable modules, resulting
in an error like:
drivers/built-in.o: In function `utmi_phy_clk_disable':
drivers/usb/phy/phy-tegra-usb.c:302: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_clk_enable':
drivers/usb/phy/phy-tegra-usb.c:324: undefined reference to `tegra_ehci_set_phcd'
drivers/built-in.o: In function `utmi_phy_power_on':
drivers/usb/phy/phy-tegra-usb.c:447: undefined reference to `tegra_ehci_set_pts'
This turns the interface into a one-way dependency by letting the tegra ehci
driver pass two function pointers for callbacks that need to be called by
the phy driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bunch of changes here, the most interesting one subsystem wise being
Morimoto-san's work to create snd_soc_component which doesn't do much
for now but will be pretty important going forwards:
- Add a new component object type which will form the basis of moving
to a more generic handling of SoC and off-SoC components, contributed
by Kuninori Morimoto.
- A fairly large set of cleanups for the dmaengine integration from
Lars-Peter Clausen, starting to move towards being able to have a
generic driver based on the library.
- Performance optimisations to DAPM from Ryo Tsutsui.
- Support for mixer control sharing in DAPM from Stephen Warren.
- Multiplatform ARM cleanups from Arnd Bergmann.
- New CODEC drivers for AK5385 and TAS5086 from Daniel Mack.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=lx37
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.10
A bunch of changes here, the most interesting one subsystem wise being
Morimoto-san's work to create snd_soc_component which doesn't do much
for now but will be pretty important going forwards:
- Add a new component object type which will form the basis of moving
to a more generic handling of SoC and off-SoC components, contributed
by Kuninori Morimoto.
- A fairly large set of cleanups for the dmaengine integration from
Lars-Peter Clausen, starting to move towards being able to have a
generic driver based on the library.
- Performance optimisations to DAPM from Ryo Tsutsui.
- Support for mixer control sharing in DAPM from Stephen Warren.
- Multiplatform ARM cleanups from Arnd Bergmann.
- New CODEC drivers for AK5385 and TAS5086 from Daniel Mack.
The link change is detected via the interrupt pipe, and bulk
pipes are responsible for transfering packets, so it is reasonable
to stop bulk transfer after link is reported as off.
Two adavantages may be obtained with stopping bulk transfer
after link becomes off:
- USB bus bandwidth is saved(USB bus is shared bus except for
USB3.0), for example, lots of 'IN' token packets and 'NYET'
handshake packets is transfered on 2.0 bus.
- probabaly power might be saved for usb host controller since
cancelling bulk transfer may disable the asynchronous schedule of
host controller.
With this patch, when link becomes off, about ~10% performance
boost can be found on bulk transfer of anther usb device which
is attached to same bus with the usbnet device, see below
test on next-20130410:
- read from usb mass storage(Sandisk Extreme USB 3.0) on pandaboard
with below command after unplugging ethernet cable:
dd if=/dev/sda iflag=direct of=/dev/null bs=1M count=800
- without the patch
1, 838860800 bytes (839 MB) copied, 36.2216 s, 23.2 MB/s
2, 838860800 bytes (839 MB) copied, 35.8368 s, 23.4 MB/s
3, 838860800 bytes (839 MB) copied, 35.823 s, 23.4 MB/s
4, 838860800 bytes (839 MB) copied, 35.937 s, 23.3 MB/s
5, 838860800 bytes (839 MB) copied, 35.7365 s, 23.5 MB/s
average: 23.6MB/s
- with the patch
1, 838860800 bytes (839 MB) copied, 32.3817 s, 25.9 MB/s
2, 838860800 bytes (839 MB) copied, 31.7389 s, 26.4 MB/s
3, 838860800 bytes (839 MB) copied, 32.438 s, 25.9 MB/s
4, 838860800 bytes (839 MB) copied, 32.5492 s, 25.8 MB/s
5, 838860800 bytes (839 MB) copied, 31.6178 s, 26.5 MB/s
average: 26.1MB/s
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the API of usbnet_link_change, so that
usbnet can handle link change centrally, which may help to
implement killing traffic URBs for saving USB bus bandwidth
and host controller power.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRXG8GAAoJEIaOsuA1yqREJzYQAKMLW3J/TKTWS1DDuf7qMtMz
Ug6qChKZXgT1/QrNjsq2tx4jYIkNdSMtRKiUx0BnIptlUx6gM22gcsN8mXX/UJjC
FYAiWl+tYe85e9uayqqt+qVCZjTZCc7St4wQalugDHefvA7yCbiZpSaJRGlJMK+x
mePJ7MfrulDsYBXr0u+m2LOJ0qxMDi40k3/UN3aUu5yzrmBiRpVq1mySruvLwGFp
Pr6vBnprEc6bW5sRdUR4SICKLvLk5sHwHpvpkzDLYBIb/jXQwbfQri/HKeh4VMk8
trbsvHZyB7H8uuFsCHiBc6VtjcbZ4mxPUK+1PCq8hG077avdkm3ox0BERk9aRTeC
jg4mdpyWjgovwi882woPEQXNZoaAXpVDyI8tBRx92a+rGJjXSHhLQI+4Ffi4ZvzV
d+q1ZzrHxuzwa/BwcPETY76umXQqXWXg+ap1bHDY0RZFoPLdXMpl583NXGSn3gOD
dUlD0UlgYwb75333tRIPNQn3qOx0HVd6MlYPMNzl9t9c9qqfX78AYRny6ZucupRg
t9VZ6FO3D2yre9W7u3U3q2c9H7uSAKr/8xaNfvdsIWPncgvvYVIyE8MnR7AiHoPv
ZYESs/Gs6w9vUsHa9K4J16Ape7D3AMcGpXUoPUxTBHrwBexzt4j27VWtcL4ns/9r
0kcltUJ4Zq+PIjc7xgxe
=aF4r
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.10 merge window
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Signed-of-by: Felipe Balbi <balbi@ti.com>
|# modprobe dummy_hcd num=2
|# modprobe libcomposite
|# lsmod
|Module Size Used by
|libcomposite 31648 0
|dummy_hcd 19871 0
|# mkdir /sys/kernel/config/usb_gadget/oha
|# cd /sys/kernel/config/usb_gadget/oha
|# mkdir configs/def.1
|# mkdir configs/def.2
|# mkdir functions/acm.ttyS1
|# mkdir strings/0x1
|mkdir: cannot create directory `strings/0x1': Invalid argument
|# mkdir strings/0x409
|# mkdir strings/1033
|mkdir: cannot create directory `strings/1033': File exists
|# mkdir strings/1032
|# mkdir configs/def.1/strings/0x409
|# mkdir configs/def.2/strings/0x409
|#find . -ls
| 975 0 drwxr-xr-x 5 root root 0 Dec 23 17:40 .
| 978 0 drwxr-xr-x 4 root root 0 Dec 23 17:43 ./strings
| 4100 0 drwxr-xr-x 2 root root 0 Dec 23 17:43 ./strings/1032
| 995 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/1032/serialnumber
| 996 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/1032/product
| 997 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/1032/manufacturer
| 2002 0 drwxr-xr-x 2 root root 0 Dec 23 17:41 ./strings/0x409
| 998 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/0x409/serialnumber
| 999 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/0x409/product
| 1000 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./strings/0x409/manufacturer
| 977 0 drwxr-xr-x 4 root root 0 Dec 23 17:41 ./configs
| 4081 0 drwxr-xr-x 3 root root 0 Dec 23 17:41 ./configs/def.2
| 4082 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 ./configs/def.2/strings
| 2016 0 drwxr-xr-x 2 root root 0 Dec 23 17:42 ./configs/def.2/strings/0x409
| 1001 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.2/strings/0x409/configuration
| 1002 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.2/bmAttributes
| 1003 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.2/MaxPower
| 979 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 ./configs/def.1
| 980 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 ./configs/def.1/strings
| 5122 0 drwxr-xr-x 2 root root 0 Dec 23 17:42 ./configs/def.1/strings/0x409
| 1004 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.1/strings/0x409/configuration
| 1005 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.1/bmAttributes
| 1006 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./configs/def.1/MaxPower
| 976 0 drwxr-xr-x 3 root root 0 Dec 23 17:41 ./functions
| 981 0 drwxr-xr-x 2 root root 0 Dec 23 17:41 ./functions/acm.ttyS1
| 1007 0 -r--r--r-- 1 root root 4096 Dec 23 17:43 ./functions/acm.ttyS1/port_num
| 1008 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./UDC
| 1009 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bcdUSB
| 1010 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bcdDevice
| 1011 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./idProduct
| 1012 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./idVendor
| 1013 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bMaxPacketSize0
| 1014 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bDeviceProtocol
| 1015 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bDeviceSubClass
| 1016 0 -rw-r--r-- 1 root root 4096 Dec 23 17:43 ./bDeviceClass
|# cat functions/acm.ttyS1/port_num
|0
|# ls -lah /dev/ttyGS*
|crw-rw---T 1 root dialout 252, 0 Dec 23 17:41 /dev/ttyGS0
|
|# echo 0x1234 > idProduct
|# echo 0xabcd > idVendor
|# echo 1122 > strings/0x409/serialnumber
|# echo "The manufacturer" > strings/0x409/manufacturer
|# echo 1 > strings/1032/manufacturer
|# echo 1sa > strings/1032/product
|# echo tada > strings/1032/serialnumber
|echo "Primary configuration" > configs/def.1/strings/0x409/configuration
|# echo "Secondary configuration" > configs/def.2/strings/0x409/configuration
|# ln -s functions/acm.ttyS1 configs/def.1/
|# ln -s functions/acm.ttyS1 configs/def.2/
|find configs/def.1/ -ls
| 979 0 drwxr-xr-x 3 root root 0 Dec 23 17:49 configs/def.1/
| 6264 0 lrwxrwxrwx 1 root root 0 Dec 23 17:48 configs/def.1/acm.ttyS1 -> ../../../../usb_gadget/oha/functions/acm.ttyS1
| 980 0 drwxr-xr-x 3 root root 0 Dec 23 17:42 configs/def.1/strings
| 5122 0 drwxr-xr-x 2 root root 0 Dec 23 17:49 configs/def.1/strings/0x409
| 6284 0 -rw-r--r-- 1 root root 4096 Dec 23 17:47 configs/def.1/strings/0x409/configuration
| 6285 0 -rw-r--r-- 1 root root 4096 Dec 23 17:49 configs/def.1/bmAttributes
| 6286 0 -rw-r--r-- 1 root root 4096 Dec 23 17:49 configs/def.1/MaxPower
|
|echo 120 > configs/def.1/MaxPower
|
|# ls -lh /sys/class/udc/
|total 0
|lrwxrwxrwx 1 root root 0 Dec 23 17:50 dummy_udc.0 -> ../../devices/platform/dummy_udc.0/udc/dummy_udc.0
|lrwxrwxrwx 1 root root 0 Dec 23 17:50 dummy_udc.1 -> ../../devices/platform/dummy_udc.1/udc/dummy_udc.1
|# echo dummy_udc.0 > UDC
|# lsusb
|Bus 001 Device 002: ID abcd:1234 Unknown
|
|lsusb -d abcd:1234 -v
|Device Descriptor:
…
| idVendor 0xabcd Unknown
| idProduct 0x1234
| bcdDevice 3.06
| iManufacturer 1 The manufacturer
| iProduct 2
| iSerial 3 1122
| bNumConfigurations 2
…
|echo "" > UDC
v5…v6
- wired up strings with usb_gstrings_attach()
- add UDC attribe. Write "udc-name" will bind the gadget. Write an empty
string (it should contain \n since 0 bytes write get optimzed away)
will unbind the UDC from the gadget. The name of available UDCs can be
obtained from /sys/class/udc/
v4…v5
- string rework. This will add a strings folder incl. language code like
strings/409/manufacturer
as suggested by Alan.
- rebased ontop reworked functions.c which has usb_function_instance
which is used prior after "mkdir acm.instance" and can be directly
used for configuration via configfs.
v3…v4
- moved functions from the root folde down to the gadget as suggested
by Michał
- configs have now their own configs folder as suggested by Michał.
The folder is still name.bConfigurationValue where name becomes the
sConfiguration. Is this usefull should we just stilc
configs/bConfigurationValue/ ?
- added configfs support to the ACM function. The port_num attribute is
exported by f_acm. An argument has been added to the USB alloc
function to distinguish between "old" (use facm_configure() to
configure and configfs interface (expose a config_node).
The port_num is currently a dumb counter. It will
require some function re-work to make it work.
scheduled for v5:
- sym linking function into config.
v2…v3
- replaced one ifndef by ifdef as suggested by Micahał
- strstr()/strchr() function_make as suggested by Micahł
- replace [iSerialNumber|iProduct|iManufacturer] with
[sSerialNumber|sProduct|sManufacturer] as suggested by Alan
- added creation of config descriptors
v1…v2
- moved gadgets from configfs' root directory into /udcs/ within our
"usb_gadget" folder. Requested by Andrzej & Michał
- use a dot as a delimiter between function's name and its instance's name
as suggested by Michał
- renamed all config_item_type, configfs_group_operations, make_group,
drop_item as suggested by suggested by Andrzej to remain consisten
within this file and within other configfs users
- Since configfs.c and functions.c are now part of the udc-core module,
the module itself is now called udc. Also added a tiny ifdef around
init code becuase udc-core is subsys init and this is too early for
configfs in the built-in case. In the module case, we can only have
one init function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixup below sparse errors
CHECK ${RENESAS_USB}/common.c
${RENESAS_USB}/common.c:313:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:322:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:384:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:524:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:545:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:574:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:606:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/mod_gadget.c:233:28: warning: symbol 'req_clear_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:274:28: warning: symbol 'req_set_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:375:28: warning: symbol 'req_get_status' was not declared. Should it be static?
[ balbi@ti.com : added three sparse fixes to mod_gadget.c ]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch (as1675) removes the CONFIG_USB_SUSPEND option, essentially
replacing it everywhere with CONFIG_PM_RUNTIME (except for one place
in hub.c, where it is replaced with CONFIG_PM because the code needs
to be used in both runtime and system PM). The net result is code
shrinkage and simplification.
There's very little point in keeping CONFIG_USB_SUSPEND because almost
everybody enables it. The few that don't will find that the usbcore
module has gotten somewhat bigger and they will have to take active
measures if they want to prevent hubs from being runtime suspended.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the port MSR-wait queue now that all drivers have been migrated
to the tty-port queue.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic get_icount implementation that subdrivers relying on the
port interrupt counters can use.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add generic TIOCMIWAIT implementation which correctly handles hangup,
USB-device disconnect, does not rely on the deprecated sleep_on
functions and hence does not suffer from the races currently affecting
several usb-serial drivers.
This makes it much easier to add TIOCMIWAIT support to subdrivers as the
tricky details related to hangup and disconnect (e.g. atomicity, that
the private port data may have been freed when woken up, and waking up
processes at disconnect) have been handled once and for all.
To add support to a subdriver, simply set the tiocmiwait-port-operation
field, update the port icount fields and wake up any process sleeping on
the tty-port modem-status-change wait queue on changes.
Note that the tty-port initialised flag can be used to detect
disconnected as the port will be hung up as part of disconnect (and
cannot be reactivated due to the disconnected flag). However, as the
tty-port implementation currently wakes up processes before calling port
shutdown, the tty-hupping flag must also be checked to detect hangup for
now.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove empty generic release implementation and make the release
callback non-mandatory (like attach, probe and disconnect).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the now empty generic disconnect callback and make the disconnect
callback non-mandatory.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace applications need to know the maximum supported message
size.
The cdc-wdm driver translates between a character device stream
and a message based protocol. Each message is transported as a
usb control message with no further encapsulation or syncronization.
Each read or write on the character device should translate to
exactly one usb control message to ensure that message boundaries
are kept intact. That means that the userspace application must
know the maximum message size supported by the device and driver,
making this size a vital part of the cdc-wdm character device API.
CDC WDM and CDC MBIM functions export the maximum supported
message size through CDC functional descriptors. The cdc-wdm and
cdc_mbim drivers will parse these descriptors and use the value
chosen by the device. The only current way for a userspace
application to retrive the value is by duplicating the descriptor
parsing. This is an unnecessary complex task, and application
writers are likely to postpone it, using a fixed value and adding
a "todo" item.
QMI functions have no way to tell the host what message size they
support. The qmi_wwan driver use a fixed value based on protocol
recommendations and observed device behaviour. Userspace
applications must know and hard code the same value. This scheme
will break if we ever encounter a QMI device needing a device
specific message size quirk. We are currently unable to support
such a device because using a non default size would break the
implicit userspace API.
The message size is currently a hidden attribute of the cdc-wdm
userspace API. Retrieving it is unnecessarily complex, increasing
the possibility of drivers and applications using different limits.
The resulting errors are hard to debug, and can only be replicated
on identical hardware.
Exporting the maximum message size from the driver simplifies the
task for the userspace application, and creates a unified
information source independent of device and function class. It also
serves to document that the message size is part of the cdc-wdm
userspace API.
This proposed API extension has been presented for the authors of
userspace applications and libraries using the current API: libmbim,
libqmi, uqmi, oFono and ModemManager. The replies were:
Aleksander Morgado:
"We do really need max message size for MBIM; and as you say, it may be
good to have the max message size info also for QMI, so the new ioctl
seems a good addition. So +1 from my side, for what it's worth."
Dan Williams:
"Yeah, +1 here. I'd prefer the sysfs file, but the fact that that
doesn't work for fd passing pretty much kills it."
No negative replies are so far received.
Cc: Aleksander Morgado <aleksander@lanedo.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().
Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.
All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
(1) root port that doesn't have an entry
(2) root port with unknown speed
(3) root port that is listed twice and with different speeds.
So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Here are a number of USB fixes that resolve issues that have been reported
against 3.9-rc3.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlFMnR0ACgkQMUfUDdst+yliJwCeNOJ0bz7Crzs3NepnRWHaHJ0Z
OmQAnRvQMX1OpqDCsjnc7RW2gL/2TDNd
=05gg
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of USB fixes that resolve issues that have been
reported against 3.9-rc3."
* tag 'usb-3.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (37 commits)
USB: ti_usb_3410_5052: fix use-after-free in TIOCMIWAIT
USB: ssu100: fix use-after-free in TIOCMIWAIT
USB: spcp8x5: fix use-after-free in TIOCMIWAIT
USB: quatech2: fix use-after-free in TIOCMIWAIT
USB: pl2303: fix use-after-free in TIOCMIWAIT
USB: oti6858: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix use-after-free in TIOCMIWAIT
USB: mos7840: fix broken TIOCMIWAIT
USB: mct_u232: fix use-after-free in TIOCMIWAIT
USB: io_ti: fix use-after-free in TIOCMIWAIT
USB: io_edgeport: fix use-after-free in TIOCMIWAIT
USB: ftdi_sio: fix use-after-free in TIOCMIWAIT
USB: f81232: fix use-after-free in TIOCMIWAIT
USB: cypress_m8: fix use-after-free in TIOCMIWAIT
USB: ch341: fix use-after-free in TIOCMIWAIT
USB: ark3116: fix use-after-free in TIOCMIWAIT
USB: serial: add modem-status-change wait queue
USB: serial: fix interface refcounting
USB: io_ti: fix get_icount for two port adapters
USB: garmin_gps: fix memory leak on disconnect
...
Add modem-status-change wait queue to struct usb_serial_port that
subdrivers can use to implement TIOCMIWAIT.
Currently subdrivers use a private wait queue which may have been
released when waking up after device disconnected.
Note that we're adding a new wait queue rather than reusing the tty-port
one as we do not want to get woken up at hangup (yet).
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building a kernel for imx_v4_v5_defconfig with CONFIG_USB_ULPI disabled, results
in the following error:
arch/arm/mach-imx/built-in.o: In function 'pca100_init':
platform-mx2-emma.c:(.init.text+0x6788): undefined reference to 'otg_ulpi_create'
platform-mx2-emma.c:(.init.text+0x682c): undefined reference to 'mxc_ulpi_access_ops'
Fix this by providing a no-op definition of *otg_ulpi_create for the case when
CONFIG_USB_ULPI is not defined.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull networking fixes from David Miller:
1) Fix ARM BPF JIT handling of negative 'k' values, from Chen Gang.
2) Insufficient space reserved for bridge netlink values, fix from
Stephen Hemminger.
3) Some dst_neigh_lookup*() callers don't interpret error pointer
correctly, fix from Zhouyi Zhou.
4) Fix transport match in SCTP active_path loops, from Xugeng Zhang.
5) Fix qeth driver handling of multi-order SKB frags, from Frank
Blaschka.
6) fec driver is missing napi_disable() call, resulting in crashes on
unload, from Georg Hofmann.
7) Don't try to handle PMTU events on a listening socket, fix from Eric
Dumazet.
8) Fix timestamp location calculations in IP option processing, from
David Ward.
9) FIB_TABLE_HASHSZ setting is not controlled by the correct kconfig
tests, from Denis V Lunev.
10) Fix TX descriptor push handling in SFC driver, from Ben Hutchings.
11) Fix isdn/hisax and tulip/de4x5 kconfig dependencies, from Arnd
Bergmann.
12) bnx2x statistics don't handle 4GB rollover correctly, fix from
Maciej Żenczykowski.
13) Openvswitch bug fixes for vport del/new error reporting, missing
genlmsg_end() call in netlink processing, and mis-parsing of
LLC/SNAP ethernet types. From Rich Lane.
14) SKB pfmemalloc state should only be propagated from the head page of
a compound page, fix from Pavel Emelyanov.
15) Fix link handling in tg3 driver for 5715 chips when autonegotation
is disabled. From Nithin Sujir.
16) Fix inverted test of cpdma_check_free_tx_desc return value in
davinci_emac driver, from Mugunthan V N.
17) vlan_depth is incorrectly calculated in skb_network_protocol(), from
Li RongQing.
18) Fix probing of Gobi 1K devices in qmi_wwan driver, and fix NCM
device mode backwards compat in cdc_ncm driver. From Bjørn Mork.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
inet: limit length of fragment queue hash table bucket lists
qeth: Fix scatter-gather regression
qeth: Fix invalid router settings handling
qeth: delay feature trace
tcp: dont handle MTU reduction on LISTEN socket
bnx2x: fix occasional statistics off-by-4GB error
vhost/net: fix heads usage of ubuf_info
bridge: Add support for setting BR_ROOT_BLOCK flag.
bnx2x: add missing napi deletion in error path
drivers: net: ethernet: ti: davinci_emac: fix usage of cpdma_check_free_tx_desc()
ethernet/tulip: DE4x5 needs VIRT_TO_BUS
isdn: hisax: netjet requires VIRT_TO_BUS
net: cdc_ncm, cdc_mbim: allow user to prefer NCM for backwards compatibility
rtnetlink: Mask the rta_type when range checking
Revert "ip_gre: make ipgre_tunnel_xmit() not parse network header as IP unconditionally"
Fix dst_neigh_lookup/dst_neigh_lookup_skb return value handling bug
smsc75xx: configuration help incorrectly mentions smsc95xx
net: fec: fix missing napi_disable call
net: fec: restart the FEC when PHY speed changes
skb: Propagate pfmemalloc on skb from head page only
...
Update irq handling code to notify all possible link status changes of
AB8500 and AB8505 to the ux500-musb glue driver. The additional event
codes will be used for pm-runtime implementation, and are defined in a
separate ux500-specific header.
This also modify the irq registration code to use devm_* helpers and
drop all non necessary fail path code.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
in cases where PHY layer isn't enabled, we want
to still return an error code (actually an error
pointer) so that our users don't need to cope with
either error pointer of NULL.
This will simplify users as below:
- return IS_ERR(phy) ? PTR_ERR(phy) : -ENODEV;
+ return PTR_ERR(phy);
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
return -EPROBE_DEFER from dwc3_omap_mailbox in dwc3-omap.c, if the probe of
dwc3-omap has not yet been executed or failed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this method will be used to enable or disable
the charge pump.
Whenever we have DRD devices, we need to be
able to turn VBUS on or off whenever we want.
Note that in the ideal case, this would be
controlled by the ID-pin Interrupt, but not
all devices have ID-pin properly routed since
manufacturers can choose to save that trace
if they're building a host-only product out
of a DRD IP.
This is also useful during debugging where
we might not have the proper cable hanging
around.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We already have a considerable amount of USB
PHY drivers, making it a menuconfig just
prevents us from adding too much churn to
USB's menuconfig.
While at that, also select USB_OTG_UTILS from
this new menuconfig just to keep backwards
compatibility until we manage to remove
that symbol.
Signed-off-by: Felipe Balbi <balbi@ti.com>
otg.c only had a single function definition
which might make more sense to be placed in
usb-common.c. While doing that, we also delete
otg.c since it's now empty.
Signed-off-by: Felipe Balbi <balbi@ti.com>
all other functions under drivers/usb/ start
with usb_, let's do the same thing.
This patch is in preparation for moving otg_state_string
to usb-common.c and deleting otg.c completely.
Signed-off-by: Felipe Balbi <balbi@ti.com>
not all UDC drivers need a proper release function,
for those which don't need it, we udc-core will provide
a no-op release method so we can remove "redefinition"
of such methods in almost every UDC driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this function will receive enum usb_device_state
and return a human-readable string from it or,
case an unknown value is passed as argument,
the string "UNKNOWN".
Signed-off-by: Felipe Balbi <balbi@ti.com>
We don't need the ->register_my_device flag
anymore because all UDC drivers have been
properly converted.
Let's remove every history of it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently all UDC drivers are calling
device_register() before calling
usb_add_gadget_udc(). In order to avoid
code duplication, we can allow udc-core.c
register that device.
However that would become a really large patch,
so to cope with the meanwhile and allow us
to write bite-sized patches, we're adding
a flag which will be set by UDC driver once
it removes the code for registering the
gadget device.
Once all are converted, the new flag will
be removed.
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add clk_rate parameter to platform data. If supplied, the
NOP phy driver will program the clock to that rate during probe.
Also add 2 flags, needs_vcc and needs_reset.
If the flag is set and the regulator couldn't be found
then the driver will bail out with -EPROBE_DEFER.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
UAC2 compliant audio devices may announce the capability to transport
raw audio data on their endpoints. Catch this and handle it as
'special' stream on the ALSA side.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit bd329e1 ("net: cdc_ncm: do not bind to NCM compatible MBIM devices")
introduced a new policy, preferring MBIM for dual NCM/MBIM functions if
the cdc_mbim driver was enabled. This caused a regression for users
wanting to use NCM.
Devices implementing NCM backwards compatibility according to section
3.2 of the MBIM v1.0 specification allow either NCM or MBIM on a single
USB function, using different altsettings. The cdc_ncm and cdc_mbim
drivers will both probe such functions, and must agree on a common
policy for selecting either MBIM or NCM. Until now, this policy has
been set at build time based on CONFIG_USB_NET_CDC_MBIM.
Use a module parameter to set the system policy at runtime, allowing the
user to prefer NCM on systems with the cdc_mbim driver.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Reported-by: Geir Haatveit <nospam@haatveit.nu>
Reported-by: Tommi Kyntola <kynde@ts.ray.fi>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54791
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few trivial fixes for composite driver:
Warning(include/linux/usb/composite.h:165): No description found for parameter
'fs_descriptors'
Warning(include/linux/usb/composite.h:165): Excess struct/union/enum/typedef
member 'descriptors' description in 'usb_function'
Warning(include/linux/usb/composite.h:321): No description found for parameter
'gadget_driver'
Warning(drivers/usb/gadget/composite.c:1777): Excess function parameter 'bind'
description in 'usb_composite_probe'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUSUyPGCrR//JCVInAQI4YA/+Nb0FaA7qMmTPuJhm7aZNfnwBcGxZ7IZp
s2xByEl3r5zbLKlKGNGE0x7Q7ETHV4y9tohzi9ZduH2b60dMRYgII06CEmDPu6/h
4vBap2oLzfWfs9hwpCIh7N9wNzxSj/R42vlXHhNmspHlw7cFk1yw5EeJ+ocxmZPq
H9lyjAxsGErkZyM/xstNQ1Uvhc8XHAFSUzWrg8hvf6AVVR8hwpIqVzfIizv6Vpk6
ryBoUBHfdTztAOrafK54CdRc7l6kVMomRodKGzMyasnBK3ZfFca3IR7elnxLyEFJ
uPDu5DKOdYrjXC8X2dPM6kYiE41YFuqOV2ahBt9HqRe6liNBLHQ6NAH7f7+jBWSI
eeWe84c2vFaqhAGlci/xm4GaP0ud5ZLudtiVPlDY5tYIADqLygNcx1HIt/5sT7QI
h34LMjc4+/TGVWTVf5yRmIzTrCXZv5YoAak3UWFoM4nVBo/eYVyNLEt5g9YsfjrC
P/GWrXJJvOCB3gAi31pgGYJzZg8K7kTTAh/dgxjqzU4f6nGRm5PBydiJe18/lWkH
qtfNE0RbhxCi3JEBnxW48AIEndVSRbd7jf8upC/s9rPURtFSVXp4APTHVyNUKCip
gojBxcRYtesyG/53nrwdTyiyHx6GocmWnMNZJoDo0UQEkog2dOef+StdC3zhc2Vm
9EttcFqWJ+E=
=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZ/kACgkQMUfUDdst+ylEhwCgyM0JEOgLuW7M8D+oNcitZn51
g7oAniD0IkLG8RCB8plLj+82AvthalCo
=bHSs
-----END PGP SIGNATURE-----
Merge tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB merge for 3.9-rc1
Nothing major, lots of gadget fixes, and of course, xhci stuff.
All of this has been in linux-next for a while, with the exception of
the last 3 patches, which were reverts of patches in the tree that
caused problems, they went in yesterday."
* tag 'usb-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (190 commits)
Revert "USB: EHCI: make ehci-vt8500 a separate driver"
Revert "USB: EHCI: make ehci-orion a separate driver"
Revert "USB: update host controller Kconfig entries"
USB: update host controller Kconfig entries
USB: EHCI: make ehci-orion a separate driver
USB: EHCI: make ehci-vt8500 a separate driver
USB: usb-storage: unusual_devs update for Super TOP SATA bridge
USB: ehci-omap: Fix autoloading of module
USB: ehci-omap: Don't free gpios that we didn't request
USB: option: add Huawei "ACM" devices using protocol = vendor
USB: serial: fix null-pointer dereferences on disconnect
USB: option: add Yota / Megafon M100-1 4g modem
drivers/usb: add missing GENERIC_HARDIRQS dependencies
USB: storage: properly handle the endian issues of idProduct
testusb: remove all mentions of 'usbfs'
usb: gadget: imx_udc: make it depend on BROKEN
usb: omap_control_usb: fix compile warning
ARM: OMAP: USB: Add phy binding information
ARM: OMAP2: MUSB: Specify omap4 has mailbox
ARM: OMAP: devices: create device for usb part of control module
...
that were dropped from linux next because of the merge conflicts
as requested by me and Olof. The reason was that at this point
we really should be able to do the arch/arm related changes
separately from driver changes to avoid dependencies between
branches.
These patches were initially part of the USB related MFD patches.
Based on our comments, Roger Quadros quickly reworked these
patches into a shared branch between ARM SoC tree and the MFD
tree, then separate patches for the OMAP platform data and
MFD driver.
Note that this branch will conflict with c1d1cd597f
("ARM: OMAP2+: omap_device: remove obsolete pm_lats and
early_device code"). Please see http://lkml.org/lkml/2013/2/11/16
for the merge resolution.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=svW/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.9/usb-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
These changes contain the OMAP USB related platform data changes
that were dropped from linux next because of the merge conflicts
as requested by me and Olof. The reason was that at this point
we really should be able to do the arch/arm related changes
separately from driver changes to avoid dependencies between
branches.
These patches were initially part of the USB related MFD patches.
Based on our comments, Roger Quadros quickly reworked these
patches into a shared branch between ARM SoC tree and the MFD
tree, then separate patches for the OMAP platform data and
MFD driver.
Note that this branch will conflict with c1d1cd597f
("ARM: OMAP2+: omap_device: remove obsolete pm_lats and
early_device code"). Please see http://lkml.org/lkml/2013/2/11/16
for the merge resolution.
[arnd - resolved the merge conflict]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull networking fixes from David Miller:
1) Revert iwlwifi reclaimed packet tracking, it causes problems for a
bunch of folks. From Emmanuel Grumbach.
2) Work limiting code in brcmsmac wifi driver can clear tx status
without processing the event. From Arend van Spriel.
3) rtlwifi USB driver processes wrong SKB, fix from Larry Finger.
4) l2tp tunnel delete can race with close, fix from Tom Parkin.
5) pktgen_add_device() failures are not checked at all, fix from Cong
Wang.
6) Fix unintentional removal of carrier off from tun_detach(),
otherwise we confuse userspace, from Michael S. Tsirkin.
7) Don't leak socket reference counts and ubufs in vhost-net driver,
from Jason Wang.
8) vmxnet3 driver gets it's initial carrier state wrong, fix from Neil
Horman.
9) Protect against USB networking devices which spam the host with 0
length frames, from Bjørn Mork.
10) Prevent neighbour overflows in ipv6 for locally destined routes,
from Marcelo Ricardo. This is the best short-term fix for this, a
longer term fix has been implemented in net-next.
11) L2TP uses ipv4 datagram routines in it's ipv6 code, whoops. This
mistake is largely because the ipv6 functions don't even have some
kind of prefix in their names to suggest they are ipv6 specific.
From Tom Parkin.
12) Check SYN packet drops properly in tcp_rcv_fastopen_synack(), from
Yuchung Cheng.
13) Fix races and TX skb freeing bugs in via-rhine's NAPI support, from
Francois Romieu and your's truly.
14) Fix infinite loops and divides by zero in TCP congestion window
handling, from Eric Dumazet, Neal Cardwell, and Ilpo Järvinen.
15) AF_PACKET tx ring handling can leak kernel memory to userspace, fix
from Phil Sutter.
16) Fix error handling in ipv6 GRE tunnel transmit, from Tommi Rantala.
17) Protect XEN netback driver against hostile frontend putting garbage
into the rings, don't leak pages in TX GOP checking, and add proper
resource releasing in error path of xen_netbk_get_requests(). From
Ian Campbell.
18) SCTP authentication keys should be cleared out and released with
kzfree(), from Daniel Borkmann.
19) L2TP is a bit too clever trying to maintain skb->truesize, and ends
up corrupting socket memory accounting to the point where packet
sending is halted indefinitely. Just remove the adjustments
entirely, they aren't really needed. From Eric Dumazet.
20) ATM Iphase driver uses a data type with the same name as the S390
headers, rename to fix the build. From Heiko Carstens.
21) Fix a typo in copying the inner network header offset from one SKB
to another, from Pravin B Shelar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
net: sctp: sctp_endpoint_free: zero out secret key data
net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfree
atm/iphase: rename fregt_t -> ffreg_t
net: usb: fix regression from FLAG_NOARP code
l2tp: dont play with skb->truesize
net: sctp: sctp_auth_key_put: use kzfree instead of kfree
netback: correct netbk_tx_err to handle wrap around.
xen/netback: free already allocated memory on failure in xen_netbk_get_requests
xen/netback: don't leak pages on failure in xen_netbk_tx_check_gop.
xen/netback: shutdown the ring if it contains garbage.
net: qmi_wwan: add more Huawei devices, including E320
net: cdc_ncm: add another Huawei vendor specific device
ipv6/ip6_gre: fix error case handling in ip6gre_tunnel_xmit()
tcp: fix for zero packets_in_flight was too broad
brcmsmac: rework of mac80211 .flush() callback operation
ssb: unregister gpios before unloading ssb
bcma: unregister gpios before unloading bcma
rtlwifi: Fix scheduling while atomic bug
net: usbnet: fix tx_dropped statistics
tcp: ipv6: Update MIB counters for drops
...
This pulls in a bunch of fixes that are in Linus's tree because we need them
here for testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 6509141f9c ("usbnet: add new
flag FLAG_NOARP for usb net devices"), the newly added flag NOARP was
using an already defined value, which broke drivers using flag
MULTI_PACKET.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OMAP_CONTROL_USB isn't enabled,
there's a compile warning stating that a
particular function isn't a prototype.
Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added has_mailbox to the musb platform data to specify that omap uses
an external mailbox (in control module) to communicate with the musb
core during device connect and disconnect.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few tiny USB fixes for 3.8-rc6.
Nothing major here, some host controller bug fixes to resolve a number
of bugs that people have reported, and a bunch of additional device ids
are added to a number of drivers (which caused code to be deleted from
the usb-storage driver, always nice.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlERRT4ACgkQMUfUDdst+ylxAQCghY23x/0vT9oCsrWZzKeOFOMB
J64AoNjVngpCpIcmh/yk1tgjSRSQu3dn
=p4nA
-----END PGP SIGNATURE-----
Merge tag 'usb-3.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a few tiny USB fixes for 3.8-rc6.
Nothing major here, some host controller bug fixes to resolve a number
of bugs that people have reported, and a bunch of additional device
ids are added to a number of drivers (which caused code to be deleted
from the usb-storage driver, always nice)"
* tag 'usb-3.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
USB: storage: optimize to match the Huawei USB storage devices and support new switch command
USB: storage: Define a new macro for USB storage match rules
USB: ftdi_sio: add Zolix FTDI PID
USB: option: add Changhong CH690
USB: ftdi_sio: add PID/VID entries for ELV WS 300 PC II
USB: add OWL CM-160 support to cp210x driver
USB: EHCI: fix bug in scheduling periodic split transfers
USB: EHCI: fix for leaking isochronous data
USB: option: add support for Telit LE920
USB: qcserial: add Telit Gobi QDL device
USB: EHCI: fix timer bug affecting port resume
USB: UHCI: notify usbcore about port resumes
USB: EHCI: notify usbcore about port resumes
USB: add usb_hcd_{start,end}_port_resume
USB: EHCI: unlink one async QH at a time
USB: EHCI: remove ASS/PSS polling timeout
usb: Using correct way to clear usb3.0 device's remote wakeup feature.
usb: Prevent dead ports when xhci is not enabled
USB: XHCI: fix memory leak of URB-private data
drivers: xhci: fix incorrect bit test
...
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8pTe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: USB driver cleanup
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
* tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
usb: host: tegra: make use of PHY pointer of HCD
ARM: tegra: Add reset GPIO information to PHY DT node
usb: host: tegra: don't touch EMC clock
usb: add APIs to access host registers from Tegra PHY
USB: PHY: tegra: Get rid of instance number to differentiate PHY type
USB: PHY: tegra: get rid of instance number to differentiate legacy controller
ARM: tegra: add clocks properties to USB PHY nodes
ARM: tegra: add DT nodes for Tegra USB PHY
usb: phy: remove unused APIs from Tegra PHY.
usb: host: tegra: Resetting PORT0 based on information received via DT.
ARM: tegra: Add new DT property to USB node.
usb: phy: use kzalloc to allocate struct tegra_usb_phy
ARM: tegra: remove USB address related macros from iomap.h
A device sending 0 length frames as fast as it can has been
observed killing the host system due to the resulting memory
pressure.
Temporarily disable RX skb allocation and URB submission when
the current error ratio is high, preventing us from trying to
allocate an infinite number of skbs. Reenable as soon as we
are finished processing the done queue, allowing the device
to continue working after short error bursts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointer to PHY structure can be stored in struct usb_hcd
making use of it, to call Tegra PHY APIs.
Call to usb_phy_shutdown() is moved up in tegra_ehci_remove(),
so that to avoid dereferencing of hcd after its freed up.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
As Tegra PHY driver needs to access one of the host registers,
added few APIs.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[swarren: moved assignment of phy->is_ulpi_phy to previous patch.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra20 USB has 3 PHY instances:
Instance 1 and 3 are UTMI. Instance 2 is ULPI.
As instance number was used to differentiate ULPI from UTMI,
used DT param to get this info and processed accordingly.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[swarren: moved assignment of phy->is_ulpi_phy into this patch out
of next patch.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra20 USB has 3 PHY instances. Instance 0 is based on
legacy PHY interface and other two are standard interfaces.
As instance number was used to differentiate legacy from
standard interfaces, used DT param to get this info and
processed accordingly.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
As tegra_usb_phy_clk_disable/enable() are not being
used, removing them.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch (as1649) adds a mechanism for host controller drivers to
inform usbcore when they have begun or ended resume signalling on a
particular root-hub port. The core will then make sure that the root
hub does not get runtime-suspended while the port resume is going on.
Since commit 596d789a21 (USB: set hub's
default autosuspend delay as 0), the system tries to suspend hubs
whenever they aren't in use. While a root-hub port is being resumed,
the root hub does not appear to be in use. Attempted runtime suspends
fail because of the ongoing port resume, but the PM core just keeps on
trying over and over again. We want to prevent this wasteful effort.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c796
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: xceiv: patches for v3.9 merge window
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
finally getting rid of the old ->start()/->stop() methods
in favor of the better and improved ->udc_start()/->udc_stop().
There were surprisingly quite a few users left, but all of them
have been converted.
f_mass_storage removed some dead code, which is always great ;-)
There's also a big cleanup to the gadget framework from Sebastian
which gets us a lot closer to having only function drivers in
kernel and move over to configfs-based binding.
Other than these, there's the usual set of cleanups: s3c UDCs are
moving over to devm_regulator_bulk_get() API, at91_udc removed
an unnecessary check for work_pending() before scheduling and
there's the removal of an unused variable from uac2_pcm_trigger().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PCP4
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: gadget: patches for v3.9 merge window
finally getting rid of the old ->start()/->stop() methods
in favor of the better and improved ->udc_start()/->udc_stop().
There were surprisingly quite a few users left, but all of them
have been converted.
f_mass_storage removed some dead code, which is always great ;-)
There's also a big cleanup to the gadget framework from Sebastian
which gets us a lot closer to having only function drivers in
kernel and move over to configfs-based binding.
Other than these, there's the usual set of cleanups: s3c UDCs are
moving over to devm_regulator_bulk_get() API, at91_udc removed
an unnecessary check for work_pending() before scheduling and
there's the removal of an unused variable from uac2_pcm_trigger().
Added a driver for usb3 phy that handles the interaction between usb phy
device and dwc3 controller.
This also includes device tree support for usb3 phy driver and
the documentation with device tree binding information is updated.
Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Start using the control module driver for powering on the PHY and for
writing to the mailbox instead of writing to the control module
registers on their own.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added a new driver for the usb part of control module. This has an API
to power on the USB2 phy and an API to write to the mailbox depending on
whether MUSB has to act in host mode or in device mode.
Writing to control module registers for doing the above task which was
previously done in omap glue and in omap-usb2 phy will be removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added an API devm_usb_get_phy_by_phandle(), to get usb phy by passing a
device node phandle value. This function will return a pointer to
the phy on success, -EPROBE_DEFER if there is a device_node for the phandle,
but the phy has not been added, or a ERR_PTR() otherwise.
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to add support for multipe PHY's of the same type, new API's
for adding PHY and getting PHY has been added. Now the binding
information for the PHY and controller should be done in platform file
using usb_bind_phy API. And for getting a PHY, the device pointer of the
USB controller and an index should be passed. Based on the binding
information that is added in the platform file, usb_get_phy_dev will return the
appropriate PHY.
Already existing API's to add and get phy by type is not removed. These
API's are deprecated and will be removed once all the platforms start to
use the new API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to support platforms which has multiple PHY's (of same type) and
which has multiple USB controllers, a new design is adopted wherin the binding
information (between the PHY and the USB controller) should be passed to the
PHY library from platform specific file (board file).
So added a new API to pass the binding information.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add an API in the omap glue layer to write to the mailbox register which
can be used by comparator driver(twl). To pass the detection of the attached
device (signified by VBUS, ID) to the dwc3 core, dwc3 core has to write
to the mailbox regiter.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Those have been deprecated for a long time and
previous patches just converted all remaining
users of those.
Since there are no in-tree users and we don't
want any new users for them, let's obliterate
every piece of code related to those calls.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Updating the names of usb-phy types to more generic names:
USB_PHY_TYPE_DEIVCE & USB_PHY_TYPE_HOST; and further update
its dependencies.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We do have some USB net devices, which cannot do ARP.
so we can introduce a new flag FLAG_NOARP, then client drivers
can easily handle this kind of devices
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB strings don't (yet) fully work in multiple configs/gadget
environment. The string id is assigned to the descriptor and the struct
usb_strings. We create a copy of the individual descriptor so we don't
clash if we use a function more than once. However, we have only one
struct usb_string for each string.
Currently each function which is used multiple times checks for
"id != 0" and only assigns string ids if it did not happen yet. This
works well if we use the same function multiple times as long as we do
it within the "one" gadget we have. Trouble starts once we use the same
function in a second gadget.
In order to solve this I introduce usb_gstrings_attach(). This function will
crate a copy all structs except for the strings which are not copied.
After the copy it will assign USB ids and attach it to cdev.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The configfs can't use all of composite's hooks because ->bind() and
->unbind() has to be done a little differently. ->disconnect() and
->setup() on the hand can be recycled.
This patch exports them both so configfs can use them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch factors out two helper functions from composite_bind()
that is composite_dev_prepare() and its counterpart
composite_dev_cleanup().
This will be used by the configfs which requries a slightly different
bind/setup code because part of its configurations (i.e. config
descripts, cdev, …) are setup in advance and VID/PID and so one should
not be overwritten. Also the setup of ep0 endpoint can be delayed until
the UDC is assigned.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds udc_attach_driver() which allows to bind an UDC which is
specified by name to a driver. The name of available UDCs can be
obtained from /sys/class/udc. This interface is intended for configfs
interface.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We can have multiple usb_functions which origin is the same "instance".
Within one USB configuration there should be only one function of an
instance. This back pointer helps configfs to recoginze to which
instance a given usb_function belongs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will be used to remove a single function from a given config. Right
now "ignore" that an error at ->bind() time and cleanup later during
composite_unbind() / remove_config().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch provides an infrastructure to register & unregister a USB
function. This allows to turn a function into a module and avoid the
'#include "f_.*.c"' magic and we get a clear API / cut between the bare
gadget and its functions.
The concept is simple:
Each function defines the DECLARE_USB_FUNCTION_INIT macro whith an unique
name of the function and two allocation functions.
- one to create an "instance". The instance holds the current configuration
set. In case there are two usb_configudations with one function there will
be one instance and two usb_functions
- one to create an "function" from the instance.
The name of the instance is used to automaticaly load the module if it the
instance is not yet available.
The usb_function callbacks are slightly modified and extended:
- usb_get_function()
creates a struct usb_function inclunding all pointers (bind,
unbind,…). It uses the "instance" to map its configuration. So we can
have _two_ struct usb_function, one for each usb_configuration.
- ->unbind()
Since the struct usb_function was not allocated in ->bind() it should
not kfree()d here. This function should only reverse what happens in
->bind() that is request cleanup and the cleanup of allocated
descriptors.
- ->free_func()
a simple kfree() of the struct usb_function
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The USB 2.0 specification says that bMaxPower is the maximum power
consumption expressed in 2 mA units and the USB 3.0 specification says
that it is expressed in 8 mA units.
This patch renames bMaxPower to MaxPower and the various /2 and *2 are
removed. Before reporting the config descriptor, the proper value is
computer based on the speed, all in-tree users are updated. MaxPower is
also increased to u16 so we can store the nokia gadget value which is
larger than the max value allowed for u8.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Empty files can get deleted by the patch program, so remove empty Kbuild
files and their links from the parent Kbuilds.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Centralise common code for manage_power() in usbnet
by making a generic simple implementation
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a device fails to do remote wakeup, this is no reason
to abort an open totally. This patch just continues without
runtime PM.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
The old parameter "port" is useless for phy notify, as one usb
phy is only for one usb port. New parameter "speed" stands for
the device's speed which is on the port, this "speed" parameter
is needed at some platforms which will do some phy operations
according to device's speed.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Mike Thompson <mpthompson@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
renesas_usbhs implements ->pullup() method, switches over
to devm_request_irq(), adds support for DMA Engine and
got a few miscelaneous cleanups.
The NCM gadget got an endianness fix and the Ethernet
gadget a frame size fix.
We're finally removing the g_file_storage gadget and
sticking to g_mass_storage and the new tcm_usb_gadget
gadgets since that was a huge duplicaton of effort anyway.
While removing g_file_storage, we also had to fix a bunch
of defconfigs which were still pointing to the old gadget.
There's a big series getting us closer to being able to
introduce our configfs interface. The series converts
functions into loadable modules which will, eventually,
be registered to the configfs interface.
Other than that there's the usual typo fixes and miscelaneous
cleanups all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQnXPMAAoJEIaOsuA1yqREkygQALIuhY6veRPZoZJltuADeAOV
h7lBkuseJxvlJsbMLnjqP5tw4W/haE1deGR+ee1ZItkPrERCX1++jkQ6hmm7e00R
mvr8rI+n3eBHSKUO89tUfCaz5UBsTl0cowPWdTwxRrV4VRJ1wVBw/oII9sfyss03
jDo+11DSjTGTB+Bz72p2NTkRiv9my2Kz+ihhqFR5VSl5FyoutG53RNKRmciJKGB+
i+RptOI+prdW1uOURHbie5FAI0xOBrE1Up2XdNiZ9blT6zcsK754Lc8erFJEZXX5
7s8Ys/HJZLQCF/fRt4WAw8e1lSPELD2xuDMqV+WKu93aXOiAWL1SbzqK3Y+PaUDg
Red07jOxgPqgq0F1mAp3+0Rs1RnshSvKREtQhZqsttg7suXhDB0q7h61CX8uQbRA
hBZh8eFexRjqOZxveeV+h4ATz00c2nlEa8cJscr5zLf4R/LSxJWT7LV5227BDkBV
9NUMA3dunDYZLqnxBv5lS2gQzmYO6G11wzdpgjnABL2WlM8Pv1lUDhY+erwvTRzd
BM+9qMd7K40BuI1JyUsbBdmuEpJAD/yWE77pT2aBrr4767x0CYjBPZqQAxXFcWi8
5NG1BzqWmH9HhwxKyWueWgNgY253cRcAzFlUN80NRA2UuNkMAeOAeJjvK48isAqJ
T1MUkQgIFNvSecpRPrEl
=umtl
-----END PGP SIGNATURE-----
Merge tag 'gadget-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
USB gadget patches from Felipe:
"usb: gadget: patches for v3.8
renesas_usbhs implements ->pullup() method, switches over
to devm_request_irq(), adds support for DMA Engine and
got a few miscelaneous cleanups.
The NCM gadget got an endianness fix and the Ethernet
gadget a frame size fix.
We're finally removing the g_file_storage gadget and
sticking to g_mass_storage and the new tcm_usb_gadget
gadgets since that was a huge duplicaton of effort anyway.
While removing g_file_storage, we also had to fix a bunch
of defconfigs which were still pointing to the old gadget.
There's a big series getting us closer to being able to
introduce our configfs interface. The series converts
functions into loadable modules which will, eventually,
be registered to the configfs interface.
Other than that there's the usual typo fixes and miscelaneous
cleanups all over the place."
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the below two helpers to prepare for solving
the usbnet runtime PM problem, which may cause some network utilities
(ifconfig, ethtool,...) touch a suspended device.
usbnet_read_cmd_nopm()
usbnet_write_cmd_nopm()
The above two helpers should be called by usbnet resume/suspend
callback to avoid deadlock.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1623) removes the ehci_port_power() routine and all the
places that call it. There's no reason for ehci-hcd to change the
port power settings; the hub driver takes care of all that stuff.
There is one exception: When the controller is resumed from
hibernation or following a loss of power, the ports that are supposed
to be handed over to a companion controller must be powered on first.
Otherwise the handover won't work. This process is not visible to the
hub driver, so it has to be handled in ehci-hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HS and SS descriptors are staticaly created. They are updated during the
bind process with the endpoint address, string id or interface numbers.
After that, the descriptor chain is linked to struct usb_function which
is used by composite in order to serve the GET_DESCRIPTOR requests,
number of available configs and so on.
There is no need to assign the HS descriptor only if the UDC supports
HS speed because composite won't report those to the host if HS support
has not been reached. The same reasoning is valid for SS.
This patch makes sure each function updates HS/SS descriptors
unconditionally and uses the newly introduced helper function to create a
copy the descriptors for the speed which is supported by the UDC.
While at that, also rename f->descriptors to f->fs_descriptors in order
to make it more explicit what that means.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The 5+4 magic for HS tries to aim 32ms which is also what is intended
with 1 << 5 for FS. This little macro should make this easier to
understand.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces the below 3 usb command helpers:
usbnet_read_cmd / usbnet_write_cmd / usbnet_write_cmd_async
so that each low level driver doesn't need to implement them
by itself, and the dma buffer allocation for usb transfer and
runtime PM things can be handled just in one place.
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ezusb code was split out, support was added for the fx2 chip
type, but no one is using these functions, so comment it out. If
someone needs it, it can be added back in the future.
Also properly include <linux/usb/ezusb.h> into the ezusb.c file, to
ensure we catch any function prototype mis-matches
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CDC Mobile Broadband Interface Model (MBIM) specification
extends CDC NCM by
- removing the redundant ethernet header from the point-to-point
USB channel
- adding support for multiple IP (v4 and/or v6) sessions multiplexed
on the same USB channel
- adding a MBIM control channel encapsulated in CDC
- adding Device Service Streams (DSS), which are non IP generic data
streams multiplexed on the same USB channel as the IP sessions
MBIM devices are managed using the dedicated control channel, and no
data will flow on the data channel until a control session has been
established. This driver has no knowledge of MBIM control messages.
It just exports the control channel to a /dev/cdc-wdmX character
device for userspace management applications. Such an application is
therefore required to use this driver.
This patch implements basic MBIM support, reusing the NCM and WDM driver
APIs, currently limited to IP sessions with SessionID 0. DSS and
multiplexed IP sessions are not yet supported.
Signed-off-by: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move symbols and definitons which can be shared with a
MBIM driver in a new header.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on revision 1.0 of "Universal Serial Bus Communications
Class Subclass Specification for Mobile Broadband Interface
Model" available from www.usb.org
Signed-off-by: Greg Suarez <gsuarez@smithmicro.com>
[bmork: added DSS defines]
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the ohci platform driver to accept the num_ports
parameter to be set via platform_data. Setting the number of ports must be
done after the call to ohci_hcd_init().
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enhance the ehci-platform driver to also accept no_io_watchdog as a platform
data parameter. When no_io_watchdog is set to 1, the ehci controller will set
ehci->need_io_watchdog to 0. Since most EHCI controllers do need the I/O
watchdog to be on, only let those which need it to turn the watchdog off.
Make sure that we change need_io_watchdog after the call to ehci_setup()
because ehci_setup() will unconditionnaly set need_io_watchdog to 1.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some device types support a form of power management in which
the device suggests to the host that the device may be suspended
now. Support for that is best located in usbnet.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Fix the issue that EHCI registers, hostpc[0] and usbmode_ex,
are not correctly accessed on Tegra3 platform.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Patch adds support for the newer Cypress FX2LP. It also adapts
three drivers currently using ezusb to the interface change. (whiteheat
and keyspan[_pda])
Signed-off-by: René Bürgel <rene.buergel@sohard.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like for the in-tree early console debug port driver, the
hypervisor - when using a debug port based console - also needs to be
told about controller resets, so it can suppress using and then
re-initialize the debug port accordingly.
Other than the in-tree driver, the hypervisor driver actually cares
about doing this only for the device where the debug is port actually
in use, i.e. it needs to be told the coordinates of the device being
reset (quite obviously, leveraging the addition done for that would
likely benefit the in-tree driver too).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
