Add info->charging validation to avoid repeated charge or discharge
operation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The USB charger status can be notified before the charger driver registers
the USB phy notifier, so we should check the charger status in probe() in
case we missed the USB charger notification.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since the USB notifier context is atomic, we can not start or stop charging
in atomic context. Thus this patch adds one work to help to charge or
discharge.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Remove at91_ramc_of_match[] since it is not used anywhere in this code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use only one poweroff function and adapt it to work for both scenarios
(with LPDDR or not). The assignement of pm_power_off was moved at the
end of probe after all initializations are OK. This patch adapt the idea
from commit 4e018c1e9b ("power: reset: at91-poweroff: use only one
poweroff function").
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The bq24196 is another variant of the bq24190 charger ic.
Its register set is identical to the bq24192 and it even reuses
the same part number (0x5).
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add extcon support so that we can notify USB drivers of cable state
changes. Based on work from Jonathan Marek. USB OTG was tested on a LG
Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds an of_match for the usb-otg-vbus regulator to
bq24190_charger.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds support for the bq24192 variant to bq24190_charger.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
[masneyb@onstation.org: Changed if statement to a switch based on
feedback from Sebastian Reichel.]
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Switch the SI to boot mode so on a warm reboot, the SI is able to access
the flash.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Similar to gpio-reset allow to specify active and inactive delays
while keeping the 100ms defaults that were used previously all the time.
The dt-properties are named the same as in gpio-reset but get an "-ms"
suffix as properties should contain such a suffix specifying its unit.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Trivial fix to clean up indentation issue, remove an extraneous tab
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
changes related to axp813.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=FoKv
-----END PGP SIGNATURE-----
Merge tag 'psy-mfd-axp813-immutable-for-v4.21-signed' into psy-next
Immutable branch between mfd and power-supply for driver
changes related to axp813.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
AXP813 and AXP803 PMICs can control input current and minimum voltage.
Both of these values are configurable.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make use of the recommended BIT() macro for bit defines.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The axp20x_usb_power driver uses BIT() operations but lacks the include
for it. Include the bitops.h header file.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Don't populate the array cpcap_battery_irqs on the stack but instead
make it static. Makes the object code smaller by 99 bytes:
Before:
text data bss dec hex filename
13673 2448 0 16121 3ef9 cpcap-battery.o
After:
text data bss dec hex filename
13510 2512 0 16022 3e96 cpcap-battery.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Sebastian Reichel <sre@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
According to [1] and [2], the temperature values are in tenths of degree
Celsius. Exposing the Celsius value makes the battery appear on fire:
$ upower -i /org/freedesktop/UPower/devices/battery_olpc_battery
...
temperature: 236.9 degrees C
Tested on OLPC XO-1 and OLPC XO-1.75 laptops.
[1] include/linux/power_supply.h
[2] Documentation/power/power_supply_class.txt
Fixes: fb972873a7 ("[BATTERY] One Laptop Per Child power/battery driver")
Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix build errors when FUEL_GUAGE_SC27XX is enabled but IIO is either
not enabled or IIO=m and FUEL_GUAGE_SC27XX=y.
ld: drivers/power/supply/sc27xx_fuel_gauge.o: in function `sc27xx_fgu_get_temp':
sc27xx_fuel_gauge.c:(.text+0x1d2): undefined reference to `iio_read_channel_processed'
ld: drivers/power/supply/sc27xx_fuel_gauge.o: in function `sc27xx_fgu_probe':
sc27xx_fuel_gauge.c:(.text+0x97f): undefined reference to `devm_iio_channel_get'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-pm@vger.kernel.org
Acked-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds the Spreadtrum SC27XX serial PMICs fuel gauge support,
which is used to calculate the battery capacity.
Original-by: Yuanjiang Yu <yuanjiang.yu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We have introduced some battery properties to present the OCV table
temperatures and OCV capacity table values. Thus this patch add OCV
temperature and OCV table for battery information, as well as providing
some helper functions to use the OCV capacity table for users.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add one field for 'struct power_supply_battery_info' to present the battery
factory internal resistance.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral bindings
out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAlvTKWYQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhw8J5EACMAnrTxWQmXfQXOZEVxztcFavH6LP8mh2e
7FZIZ38jzHXXvl81tAg1nBhzFUU/qtvqW8NDCZ9OBxKvp6PFDNhWu241ZodSB1Kw
MZWy2A9QC+qbHYCC+SB5gOT0+Py3v7LNCBa5/TxhbFd35THJM8X0FP7gmcCGX593
9Ml1rqawT4mK5XmCpczT0cXxyC4TgVtpfDWZH2KgJTR/kwXVQlOQOGZ8a1y/wrt7
8TLIe7Qy4SFRzjhwbSta1PUehyYfe4uTSsXIJ84kMvNMxinLXQtvd7t9TfsK8p/R
WjYUneJskVjtxVrMQfdV4MxyFL1YEt2mYcr0PMKIWxMCgGDAZsHPoUZmjyh/PrCI
uiZtEHn3fXpUZAV/xEHHNirJxYyQfHGiksAT+lPrUXYYLCcZ3ZmqiTEYhGoQAfH5
CQPMuxA6yXxp6bov6zJwZSTZtkXciju8aQRhUhlxIfHTqezmGYeql/bnWd+InNuR
upANLZBh6D2jTWzDyobconkCCLlVkSqDoqOx725mMl6hIcdH9d2jVX7hwRf077VI
5i3CyPSJOkSOLSdB8bAPYfBoaDtH2bthxieUrkkSbIjbwHO1H6a2lxPeG/zah0a3
ePMGhi7J84UM4VpJEi000cP+bhPumJtJrG7zxP7ldXdfAF436sQ6KRptlcpLpj5i
IwMhUQNH+g==
=335v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
Use the new of_get_compatible_child() helper to lookup the usb sibling
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(non-sibling) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the parent device node).
While at it, also fix the related phy-node reference leak.
Fixes: f5e4edb8c8 ("power: twl4030_charger: find associated phy by more reliable means.")
Cc: stable <stable@vger.kernel.org> # 4.2
Cc: NeilBrown <neilb@suse.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 201510 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Trivial fix to spelling mistake in MODULE_DESCRIPTION text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
omap_sr_register_pmic() was introduced in 2010 in commit
984aa6dbf4 ("OMAP3: PM: Adding smartreflex driver support.")
. There was never any caller of this function in mainline resulting in a
warning
sr_init: No PMIC hook to init smartreflex
for each machine where this driver is enabled. So remove the unused
function and the pr_warn.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update the binding and driver for pms405 pon.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
According to the datasheet, bq27411 is similar to bq27421.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds the SC2731 PMIC switch charger support.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This avoids getting woken up from suspend after power interruptions
when the bci wrongly thinks the battery is full just because
of input current going low because of low input power
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
the charging current uses unsigned int variables, if we step back
if the current is still low, we would run into negative which
means setting the target to a huge value.
Better add checks here.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f1 ("mfd: max8998: Add support for Device Tree")
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Immutable branch between mfd and power-supply for driver
changes in CROS USBPD charger driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=ya3t
-----END PGP SIGNATURE-----
Merge tag 'psy-mfd-cros-immutable-for-v4.20-signed' into psy-next
Immutable branch for mfd and power-supply for v4.20
Immutable branch between mfd and power-supply for driver
changes in CROS USBPD charger driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
ChromeOS devices can have one optional dedicated port.
The Dedicated port is unique and similar to the USB PD ports
except that it doesn't support as many properties.
The presence of a dedicated port is determined from whether the
EC's charger port count is equal to 'number of USB PD port' + 1.
The dedicated port ID is always the last valid port ID.
This commit keeps compatibility with Embedded Controllers that do not
support the new EC_CMD_CHARGE_PORT_COUNT command by setting
the number of charger port to be equal to the number of USB PD port
when this command fails.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Immutable branch between mach-at91 and power-supply for driver
changes in at91-poweroff.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----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=n/Lz
-----END PGP SIGNATURE-----
Merge tag 'psy-at91-poweroff-immutable-for-v4.20-signed' into psy-next
Immutable branch for mach-at91 and power-supply for v4.20
Immutable branch between mach-at91 and power-supply for driver
changes in at91-poweroff.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There should be only one instance of struct shdwc in the system. This is
referenced through at91_shdwc. Return in probe if at91_shdwc is already
allocated.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Rename at91_shdwc_base member of struct shdwc to shdwc_base. There is
already an "at91" string in at91_shdwc object.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make sclk part of struct shdwc to have all the data specific to SHDWC
grouped together in one structure.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Make mpddrc_base part of struct shdwc since there is also only one
instance of struct shdwc *at91_shdwc in system and to have all data
specific to SHDWC grouped together.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use only one poweroff function for sama5d2 and adapt it to work for both
scenarios (having LPDDR or not).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The SAMA5D2 NRST input signal is resynchronized with the SLCK clock and it
can take up to 2 SLCK cycles (about 90us) for the internal reset to be
effective. During this delay, the VDDCORE current consumption may still be
high (application-dependent) with the VDDCORE regulator already OFF. Under
such conditions, VDDCORE may operate below its operating range leading to
potential register corruption.
To prevent such situation, it is recommended to decrease significantly the
power consumption of the device once the voltage regulator is turned-off.
This can be achieved by operating the device at a much lower low frequency.
To solve this switch the master clock to slock clock just before writing
shutdown command to shutdown controller.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Suggested-by: Patrice Vilchez <patrice.vilchez@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If kstrtoul() fails then we print "charge_full" when it's uninitialized.
The debug printk doesn't add anything so I deleted it and cleaned these
two functions up a bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This adds rate limiting to the message that is printed when reading a
power supply property via sysfs returns an error. This will prevent
userspace applications from unintentionally dDOSing the system by
continuously reading a property that returns an error.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BQ2589x family has the capability of reading the current battery voltage.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BQ25896 is almost identical to the BQ25890.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There are a few table entries that aren't used. Drop them.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
To ease adding a new part variant some debugging is handy.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Replace GPL v2.0 and v2.0+ license statements with SPDX license
identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
simple_strtoul is obsolete, and use kstrtoint instead
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pointer 'dev' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Almost all files in the kernel are either plain text or UTF-8 encoded. A
couple however are ISO_8859-1, usually just a few characters in a C
comments, for historic reasons.
This converts them all to UTF-8 for consistency.
Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms@verge.net.au> [IPVS portion]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> [IIO]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The URL of bq27441-g1 and bq27426 are missing and bq27520-g4 is duplicated.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
It seems that a *break* is missing in order to avoid a fall-through.
Otherwise, the calculation of *data* makes no sense.
Addresses-Coverity-ID: 1271172 ("Missing break in switch")
Fixes: 87c2d90678 ("power: max77693: Add charger driver for Maxim 77693")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1394724 ("Missing break in switch")
Addresses-Coverity-ID: 114958 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This fixes the value that accounts for the Vce of a transistor in the
LEGO MINDSTORMS EV3 power supply driver. The old value (200mV) was the
max value from the data sheet. After testing, the actual value has been
found to be 50mV. By using 50mV we get a more accurate voltage
indication.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This changes the LEGO MINDSTORMS EV3 power supply driver to return an
error if iio_read_channel_processed() fails.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add a matching table for devicetree probing, and optionally set the module
parameter variables from DT properties.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This patch removes the w1 slave driver that used to register the w1 family
and instanciate a platform device at runtime. The code now lives in the
supply driver instead to avoid that level of indirection.
The old device name "ds2760-battery.0" is preserved, so userspace
applications can access the same virtual device nodes as before.
Note that because the w1 core does not currently have a framework for
suspend/resume, the driver now registers a PM notifier callback.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We end up reading one element beyond the end of the adp5061_vmax[] array
here.
Fixes: fe8e81b7e8 ("adp5061: New driver for ADP5061 I2C battery charger")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds basic support for Analog Devices I2C programmable linear
battery charger.
With this driver, some parameters can be read and configured such as:
* trickle charge current level (PRECHARGE_CURRENT)
* trickle charge voltage threshold (VOLTAGE_MIN)
* weak charge threshold (VOLTAGE_AVG)
* constant current (CONSTANT_CHARGE_CURRENT)
* constant charge voltage limit (CONSTANT_CHARGE_VOLTAGE_MAX)
* battery full (CAPACITY_LEVEL)
* input current limit (INPUT_CURRENT_LIMIT)
* charger status (STATUS)
* battery status (CAPACITY_LEVEL)
* termination current (CHARGE_TERM_CURRENT)
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADP5061.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
If an iio channel defines a basic property, there are duplicate entries
in /sys/class/power/*/uevent.
So add a check to avoid duplicates. Since all channels may be duplicates,
we have to modify the related error check.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We did have sporadic problems in the pinctrl framework during boot
where a pin group name unexpectedly became NULL leading to a NULL
dereference in strcmp.
Detailled analysis of the failing cases did reveal that there were
two devm allocated objects close to each other. The second one was
the affected group_desc in pinmux and the first one was the
psy_desc->properties buffer of the gab driver.
Review of the gab code showed that the address calculation for
one memcpy() is wrong. It does
properties + sizeof(type) * index
but C is defined to do the index multiplication already for
pointer + integer additions. Hence the factor was applied twice
and the memcpy() does write outside of the properties buffer.
Sometimes it happened to be the pinctrl and triggered the strcmp(NULL).
Anyways, it is overkill to use a memcpy() here instead of a simple
assignment, which is easier to read and has less risk for wrong
address calculations. So we change code to a simple assignment.
If we initialize the index to the first free location, we can even
remove the local variable 'properties'.
This bug seems to exist right from the beginning in 3.7-rc1 in
commit e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Fixes: e60fea794e ("power: battery: Generic battery driver using IIO")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We should look at val which contains the value read from the register,
not ret which is always 0 on a successful read.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: eac53b3664 ("power: supply: axp288_charger: Drop platform_data dependency")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
getnstimeofday64() is deprecated in favor of the ktime_get() family.
The direct replacement would be ktime_get_real_ts64(), but we only need
the seconds value, and it seems better to use boottime than real time
to avoid unexpected behavior with a concurrent settimeofday().
ktime_get_seconds() might also work, but it seems better to use
boottime than monotonic time since I assume that the charging
process continues during suspend.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Even after the previous fix I have experienced more spurious
poweroffs on the gemini SoC. After this fix it finally seems
to go away.
Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Vexpress platforms provide two different restart handlers: SYS_REBOOT
that restart the entire system, while DB_RESET only restarts the
daughter board containing the CPU. DB_RESET is overridden by SYS_REBOOT
if it exists.
notifier_chain_register used in register_restart_handler by design
relies on notifiers to be registered once only, however vexpress restart
notifier can get registered twice. When this happen it corrupts list
of notifiers, as result some notifiers can be not called on proper
event, traverse on list can be cycled forever, and second unregister
can access already freed memory.
So far, since this was the only restart handler in the system, no issue
was observed even if the same notifier was registered twice. However
commit 6c5c0d48b6 ("watchdog: sp805: add restart handler") added
support for SP805 restart handlers and since the system under test
contains two vexpress restart and two SP805 watchdog instances, it was
observed that during the boot traversing the restart handler list looped
forever as there's a cycle in that list resulting in boot hang.
This patch fixes the issues by ensuring that the notifier is installed
only once.
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: 46c99ac662 ("power/reset: vexpress: Register with kernel restart handler")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver gets various bits of information about what is connected to
USB PD ports from the EC and converts that into power_supply properties.
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Trivial fix to spelling mistake in dev_warn message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
zx_reboot_probe() increments refcnt of zx296702-pcu device node by
of_find_compatible_node() and leaves it undecremented on both
successful and error paths.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver was originally submitted for the TI BQ20Z75 battery IC
(commit a7640bfa10 ("power_supply: Add driver for TI BQ20Z75 gas gauge
IC")) and later renamed to express generic SBS support. While it's
mostly true that this driver implemented a standard SBS command set, it
takes liberties with the REG_MANUFACTURER_DATA register. This register
is specified in the SBS spec, but it doesn't make any mention of what
its actual contents are.
We've sort of noticed this optionality previously, with commit
17c6d3979e ("sbs-battery: make writes to ManufacturerAccess
optional"), where we found that some batteries NAK writes to this
register.
What this really means is that so far, we've just been lucky that most
batteries have either been compatible with the TI chip, or else at least
haven't reported highly-unexpected values.
For instance, one battery I have here seems to report either 0x0000 or
0x0100 to the MANUFACTURER_ACCESS_STATUS command -- while this seems to
match either Wake Up (bits[11:8] = 0000b) or Normal Discharge
(bits[11:8] = 0001b) status for the TI part [1], they don't seem to
actually correspond to real states (for instance, I never see 0101b =
Charge, even when charging).
On other batteries, I'm getting apparently random data in return, which
means that occasionally, we interpret this as "battery not present" or
"battery is not healthy".
All in all, it seems to be a really bad idea to make assumptions about
REG_MANUFACTURER_DATA, unless we already know what battery we're using.
Therefore, this patch reimplements the "present" and "health" checks to
the following on most SBS batteries:
1. HEALTH: report "unknown" -- I couldn't find a standard SBS command
that gives us much useful here
2. PRESENT: just send a REG_STATUS command; if it succeeds, then the
battery is present
Also, we stop sending MANUFACTURER_ACCESS_SLEEP to non-TI parts. I have
no proof that this is useful and supported.
If someone explicitly provided a 'ti,bq20z75' compatible property, then
we continue to use the existing TI command behaviors, and we effectively
revert commit 17c6d3979e ("sbs-battery: make writes to
ManufacturerAccess optional") to again make these commands required.
[1] http://www.ti.com/lit/er/sluu265a/sluu265a.pdf
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
* bq27xxx: Add BQ27426 support
* ab8500: Drop AB8540/9540 support
* Introduced new usb_type property
* Properly document the power-supply ABI
* misc. cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=UB16
-----END PGP SIGNATURE-----
Merge tag 'for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- bq27xxx: Add BQ27426 support
- ab8500: Drop AB8540/9540 support
- Introduced new usb_type property
- Properly document the power-supply ABI
- misc. cleanups and fixes
* tag 'for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
MAINTAINERS: add entry for LEGO MINDSTORMS EV3
power: supply: ab8500_charger: fix spelling mistake: "faile" -> "failed"
power: supply: axp288_fuel_gauge: Remove polling from the driver
power: supply: axp288_fuelguage: Do not bind when the fg function is not used
power: supply: axp288_charger: Do not bind when the charge function is not used
power: supply: axp288_charger: Support 3500 and 4000 mA input current limit
power: supply: s3c-adc-battery: fix driver data initialization
power: supply: charger-manager: Verify polling interval only when polling requested
power: supply: sysfs: Use enum to specify property
power: supply: ab8500: Drop AB8540/9540 support
power: supply: ab8500_fg: fix spelling mistake: "Disharge" -> "Discharge"
power: supply: simplify getting .drvdata
power: supply: bq27xxx: Add support for BQ27426
gpio-poweroff: Use gpiod_set_value_cansleep
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
To allow users of the power supply framework to be hw description
agnostic, this commit adds the ability to pass a fwnode pointer,
via the power_supply_config structure, to the initialisation code
of the core, instead of explicitly specifying of_ndoe. If that
fwnode pointer is provided then it will automatically resolve down
to of_node on platforms which support it, otherwise it will be NULL.
In the future, when ACPI support is added, this can be modified to
accommodate ACPI without the need to change calling code which
already provides the fwnode handle in this manner.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary data for handling io voltage domains on PX30.
As interesting tidbit, the PX30 contains two separate iodomain areas.
One in the regular General Register Files (GRF) and one in PMUGRF in the
pmu power domain.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
trivial fix to spelling mistake in dev_error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This is a signed tag/merge point to handle the cross-tree merge of the
USB and power supply subsystems for the patch series:
Subject: [PATCH v8 0/6] typec: tcpm: Add sink side support for PPS
It is based on the usb.git tree, in the usb-next branch, for merging in
4.18-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWuGASg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylqPACcDdrowGIQp0vVa7VrOJNMy9pL5K0An1cjnaUt
0sXkKK8YWC3EQSSYtr3Q
=McRU
-----END PGP SIGNATURE-----
Merge tag 'tags/tcpm-pps-4.18' into psy-next
Tag/Merge point for adding typeC power supply support
This is a signed tag/merge point to handle the cross-tree merge of the
USB and power supply subsystems for the patch series:
Subject: [PATCH v8 0/6] typec: tcpm: Add sink side support for PPS
It is based on the usb.git tree, in the usb-next branch, for merging in
4.18-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Userspace class/power_supply consumers such as upower, already know some
supplies need to be polled to get up2date info. Doing this in the kernel
and then waking up userspace just causes unnecessary wakeups and i2c
transfers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some devices with an AXP288 PMIC do not have a battery at all, or use
external charger and fuelgauge ICs instead of the AXP288 builtin
functionality.
On such devices we should not bind to the fuelgauge function to avoid
exporting a non working power_supply class device.
This also avoids the following errors repeating over and over again in
dmesg:
axp288_fuel_gauge axp288_fuel_gauge: capacity measurement not valid
axp288_fuel_gauge axp288_fuel_gauge: Error 0xe2 contents not valid
power_supply axp288_fuel_gauge: driver failed to report 'charge_now'
property: -6
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some devices with an AXP288 PMIC do not have a battery at all, or use
external charger and fuelgauge ICs instead of the AXP288 builtin
functionality.
On such devices we should not bind to the charge function to avoid
exporting a non working power_supply class device.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The AXP288 supports an input-current-limit of up to 4000 mA, this
commit adds support for the 3500 and 4000 mA settings which were
missing until now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
For power_supply_get_drvdata() routine to work correctly the driver data
has to be provided when registering power supply, otherwise driver gives up
immediately with these errors:
power_supply main-battery: no battery infos ?!
power_supply main-battery: driver failed to report `status' property: -22
Signed-off-by: Sergiy Kibrik <sakib@darkstar.site>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Driver bails out with -EINVAL when no polling specififaion is requested.
Fix that by verifing polling interval only if polling_mode is different
from CM_POLL_DISABLE.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Power supply property is in fact enum, so reflect it in code.
Also use switch statement in show property function as is done
for storing property.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Trivial fix to spelling mistake in dev_dbg message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This device is software similar to the BQ27426 except it has
different data memory offsets. Add support here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The power-off call is done in a context that must be able to sleep, so
use gpiod_set_value_cansleep instead of the atomic gpiod_set_value call.
This fixes a kernel warning at shutdown when the gpio is controlled
through an IO expander for example.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This commit adds the 'usb_type' property to represent USB supplies
which can report a number of different types based on a connection
event.
Examples of this already exist in drivers whereby the existing 'type'
property is updated, based on an event, to represent what was
connected (e.g. USB, USB_DCP, USB_ACA, ...). Current implementations
however don't show all supported connectable types, so this knowledge
has to be exlicitly known for each driver that supports this.
The 'usb_type' property is intended to fill this void and show users
all possible USB types supported by a driver. The property, when read,
shows all available types for the driver, and the one currently chosen
is highlighted/bracketed. It is expected that the 'type' property
would then just show the top-level type 'USB', and this would be
static.
Currently the 'usb_type' enum contains all of the USB variant types
that exist for the 'type' enum at this time, and in addition has
SDP and PPS types. The mirroring is intentional so as to not impact
existing usage of the 'type' property.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently there's no error checking of this parameter in the
registration function and it's blindly added to psy class and
subsequently used as is. For example if this is NULL the call
to psy_register_thermal() will try to dereference the pointer
thus causing a kernel dump.
This commit updates the registration code to add some basic
checks on the desc pointer validity, name, and presence of
properties.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
* Microsemi Ocelot reset support
* Spreadtrum SC27xx reset support
* generic gpio charger: lot's of cleanups
* axp20x fuel gauge: add AXP813 support
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=VY8H
-----END PGP SIGNATURE-----
Merge tag 'for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- Microsemi Ocelot reset support
- Spreadtrum SC27xx reset support
- generic gpio charger: lot's of cleanups
- axp20x fuel gauge: add AXP813 support
- misc fixes, including one devicetree change for the Nokia N900, that
has been Acked-by Tony Lindgren
* tag 'for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (27 commits)
power: reset: at91-reset: Switch from the pr_*() to the dev_*() logging functions
power: reset: at91-poweroff: Remove redundant dev_err call in at91_poweroff_probe()
power: reset: at91-poweroff: Switch from the pr_*() to the dev_*() logging functions
power: reset: make function sc27xx_poweroff_shutdown static
power: supply: da9150-fg: remove VLA usage
ARM: dts: omap3-n900: Add link between battery and charger
power: supply: bq2415x: add DT referencing support
power: supply: bq27xxx: support missing supplier device
max17042: propagate of_node to power supply device
power: supply: axp288_fuel_gauge: Fix full status reporting
power: supply: axp288_fuel_gauge: Do not register FG on ECS EF20EA
power: reset: gpio-poweroff: Support for timeout from device property
dt-bindings: power: reset: gpio-poweroff: Add 'timeout-ms' property
power: reset: Add Spreadtrum SC27xx PMIC power off support
power: supply: axp20x_battery: add support for AXP813
dt-bindings: power: supply: axp20x: add AXP813 battery DT binding
power: supply: axp20x_battery: use data struct for variant specific code
power: supply: gpio-charger: Remove pdata from gpio_charger
power: supply: gpio-charger: Use GPIOF_ACTIVE_LOW for legacy setup
power: supply: gpio-charger: Remove redundant dev_err call in probe function
...
Use dev_info() instead of pr_info().
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
There is an error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundancy.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use dev_info() instead of pr_info().
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The function sc27xx_poweroff_shutdown is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/power/reset/sc27xx-poweroff.c:28:6: warning: symbol
'sc27xx_poweroff_shutdown' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
In preparation to enabling -Wvla, remove VLA usage and replace it
with fixed-length arrays.
DA9150_QIF_LONG_SIZE (4 bytes) is the biggest size of an attribute which can
be accessed [1].
Fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621
[1] https://marc.info/?l=kernel-hardening&m=152059600524753&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
power_supply_am_i_supplied() can return negative error
codes. In this case we should assume, that no charger
is connected and the battery should be marked as
DISCHARGING instead of NOT_CHARGING.
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
max17042_get_status uses the core power_supply_am_i_supplied. That
function relies on DT properties to figure out the power supply
topology, and will error out without DT.
Fixes max17042 battery status being reported as "unknown".
Signed-off-by: Pierre Bourdon <delroth@google.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Commit 2b5a4b4bf2 ("power: supply: axp288_fuel_gauge: Rework
get_status()"), switched from 0A current detection to using the capacity
register for full detection.
It turns out this fixes full reporting on some devices which keep trickle
charging long after the capacity register reach 100%, but breaks it on
some other devices where the charger stops charging before the capacity
register reaches 100%. This commit fixes this by also checking for
0A current when the reported capacity is above 90%.
Fixes: 2b5a4b4bf2 ("psy: axp288_fuel_gauge: Rework get_status()")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The ECS EF20EA laptop ships an AXP288 but it is actually using a
different, separate FG chip for AC and battery monitoring. On this
laptop we need to keep using the regular ACPI driver and disable the
AXP288 FG to avoid reporting two batteries to userspace.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add support for reading a timeout value from device property.
Fall back to previous default of 3s if nothing is specified.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
On Spreadtrum platform, we need power off system through external SC27xx
series PMICs including the SC2720, SC2721, SC2723, SC2730 and SC2731 chips.
Thus this patch adds SC27xx series PMICs power-off support.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The X-Powers AXP813 PMIC has got some slight differences from
AXP20X/AXP22X PMICs:
- the maximum voltage supplied by the PMIC is 4.35 instead of 4.36/4.24
for AXP20X/AXP22X,
- the constant charge current formula is different,
It also has a bit to tell whether the battery percentage returned by the
PMIC is valid.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We used to use IDs to select a function or a feature depending on the
variant. It's easier to maintain the code by adding data structure
storing the few differences between variants so that we don't add a pile
of if conditions.
Let's use this data structure and update the code to use it.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
[updated POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN write property to use
the introduced set_max_voltage() callback]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Platform data are now used only during probe time, so remove
them from gpio_charger structure and consolidate probing
function accordingly.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[Replace of_property_read_string with dev_property_read_string]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Setting GPIOF_ACTIVE_LOW flag based on platform data gpio_active_low
makes return value of gpiod_get_value_cansleep directly usable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
There is an error message within devm_kzalloc already.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We are currently probing smartreflex with omap_device while we are
already probing smartreflex related interconnect target module with
ti-sysc driver and dts data.
Before we can flip things on for ti-sysc, we need to prepare the
smartreflex driver a bit:
1. The smartreflex clock is really for the whole interconnect target
module. So it may be configured at the parent device level with
ti-sysc
2. With ti-sysc, we have the child device manage interconnect target
module directly if pm_runtime_irq_safe() is set and there is only
one child. In that case nobody else is going to call pm_runtime_get
and put, so we need to add these calls to idle smartreflex properly
after probe if not fully configured
3. With ti-sysc, the parent driver may rebind. So we want to use
platform_driver_register() and don't want probe to be __init
Note that this patch depends on the related changes to ti-sysc driver
and omap_device probing to prevent both ti-sysc and omap_device to
try to probe smartreflex.
Cc: linux-pm@vger.kernel.org
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the D-Link DIR-685 we get spurious poweroff from
infrared. Since that block (CIR) doesn't even have a
driver this can be safely ignored, we can revisit this
code once we have a device supporting CIR.
On the D-Link DNS-313 we get spurious poweroff from
the power button. This appears to be an initialization
issue: we need to enable the block (start the state
machine) before we clear any dangling IRQ.
This patch fixes both issues.
Fixes: f7a388d6cd ("power: reset: Add a driver for the Gemini poweroff")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Temperature is measured in tenths of degree Celsius.
Fixes: 085bc24d15 ("Add LTC2941/LTC2943 Battery Gauge Driver")
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This patch adds the to_power_supply macro to upcast
a device to a power_supply struct.
This is needed because the same piece of code using
container_of is used in various other places, so we
abstract away such low-level operations via a macro.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ognjen Galic <smclt30p@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Using explicit struct device variable makes code a bit more readable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Simplify error unwinding using devm_* allocators. This also
makes driver remove function empty, so remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add properties for charge empty and charge full thresholds.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The Microsemi Ocelot SoC has a register allowing to reset the MIPS core.
Unfortunately, the syscon-reboot driver can't be used directly (but almost)
as the reset control may be disabled using another register.
Cc: linux-pm@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
* bq27xxx: add bq27521 support
* drop unused imx-snvs-poweroff driver
* improve axp288 driver
* misc. fixes
-----BEGIN PGP SIGNATURE-----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=XIx5
-----END PGP SIGNATURE-----
Merge tag 'for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- bq27xxx: add bq27521 support
- drop unused imx-snvs-poweroff driver
- improve axp288 driver
- misc fixes
* tag 'for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (32 commits)
power: supply: max17042_battery: Always fall back to default platform-data
power: supply: max17042_battery: Check battery current for status when supplied
MAINTAINERS: Add AXP288 PMIC entry
power: supply: axp288_fuel_gauge: Do not register our psy on (some) HDMI sticks
power: supply: axp288_fuel_gauge: Optimize get_current()
power: supply: axp288_fuel_gauge: Rework get_status()
power: reset: account for const type of of_device_id.data
power: supply: account for const type of of_device_id.data
bq24190: Simplify code in property_is_writeable
power: supply: axp288_fuel_gauge: Get iio-channels once during boot
power: supply: axp288_charger: Properly stop work on probe-error / remove
power: supply: axp288_charger: Simplify extcon cable handling
power: supply: axp288_charger: Use the right property for the input current limit
power: supply: axp288_charger: Pick lower input current limit not higher
power: supply: axp288_charger: Do not cache input current limit value
power: supply: axp288_charger: Remove no longer needed locking
power: supply: axp288_charger: Use regmap_update_bits to set the input limits
power: supply: axp288_charger: Cleanup some double empty lines
power: supply: axp288_charger: Remove charger-enabled state tracking
power: supply: axp288_charger: Add missing newlines to some messages
...
It is possible to have CONFIG_OF enabled on x86 builds, where we have no
firmware provided max17042_platform_data. The CONFIG_OF implementation of
max17042_get_pdata would return NULL in this case, causing the probe to
fail.
Instead always fallback to the default platform-data, as used on x86 sofar,
when there is no firmware provided pdata, independent of CONFIG_OF.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Even though the system is supplied, it may still be discharging if the
supply is e.g. only delivering 5V 0.5A. Check the avg battery current if
available for more accurate status reporting.
Cc: James <kernel@madingley.org>
Suggested-by: James <kernel@madingley.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The Intel Compute Stick (Cherry Trail version) and the Meegopad T08 HDMI
stick, both use an axp288 PMIC. They also both have this wired up in such
a way that the detection logic in the PMIC claims that a valid battery is
present, resuling in GNOME and KDE showing a full-battery in their status
bar and power-settings, while these devices do not have a battery.
For lack of a better fix add a DMI blacklist and do not register the
axp288_fuel_gauge psy on devices on the blacklist.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
First check the discharge current, and when that is non 0 use that without
also checking the charge current (which will be 0 then). This makes
get_current() do only 1 i2c read instead of 2 when on battery.
This is esp. important given the pmic i2c bus mutex stuff used on boards
with an axp288 because the SoC's own punit also may access the axp288,
which makes i2c accesses more expensive then normal.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Relying on the (dis)charge current reporting for reporting FULL back to
userspace does not work really well and often leads to the reported status
getting stuck at e.g. 98/99% (the fuelgauge is not perfect) for hours.
What happens is that when the battery is full the axp288 keeps charging it
with a very low current. Until it is really really full and once really
really full, some inaccuracies in the adc lead to it then sometimes
reporting a small discharging rate, even though an external pwr source is
used. So we end up with a status of "charging" for hours after the battery
is actually already full and sometimes this then flip-flops to discharging.
This commit fixes this by first checking if a valid Vbus is present and if
it is present using the fuel-gauge's reported percentage to check for a
full battery.
This commit also changes how get_status() determines if the battery is
charging or discharging when not reporting it as full. We still use the
current direction for this, but instead of reading 4 extra registers for
this (2 16 bit regs), simplify things by using the current-direction bit
in the power-status register, which already gets read anyways.
This also reduces the amount of i2c reads to 1 when on battery and 2
when a valid Vbus is present.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver creates a const structure that it stores in the data
field of an of_device_id array.
Add const to the declaration of the location that receives a value
from the data field to ensure that the compiler will continue to check
that the value is not modified and remove the const-dropping cast on
the access to the data field.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This driver creates two const structures that it stores in the data
field of an of_device_id array.
The data field of an of_device_id structure has type const void *, so
there is no need for a const-discarding cast when putting const values
into such a structure.
Furthermore, adding const to the declaration of the location that
receives a const value from such a field ensures that the compiler
will continue to check that the value is not modified. The
const-discarding cast on the extraction from the data field is thus
no longer needed.
Done using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Simplify function that should be trivial.
Signed-off-by: Pavel machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Get iio-channels once during boot, delaying the probe if the axp288_adc
drivers has not loaded yet, instead of getting them on demand each time
we need them.
This fixes the following errors in dmesg:
axp288_fuel_gauge axp288_fuel_gauge: ADC charge current read failed:-19
Which were caused by the ondemand iio-channel read code not finding the
channel when the axp288_adc driver had not loaded yet.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Properly stop any work we may have queued on probe-errors / remove.
Rather then adding a remove driver callback for this, and goto style
error handling to probe, use a devm_action for this.
The devm_action gets registered before we register any of the extcon
notifiers which may queue the work, devm does cleanup in reverse order,
so this ensures that the notifiers are removed before we cancel the work.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Simplify extcon cable handling using the new
devm_extcon_register_notifier_all function to listen to all cables
in one go.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Use the right property for the input current limit and make it writable.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The code before this commit would pick 900 mA when asking for an input
current limit of 600mA, rather then 500 mA, not good.
While touching almost all code using the silly xxxMA defines anyways,
also get rid of these simply typing out the numbers and switch the
unit to uA as that is the psy class standard unit for currents.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The hardware may change this underneath us.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
