Titan Ridge supports Display Port 1.4 which adds HBR3 (High Bit Rate)
rates that may be up to 8.1 Gb/s over 4 lanes. This translates to
effective data bandwidth of 25.92 Gb/s (as 8/10 encoding is removed by
the DP adapters when going over Thunderbolt fabric). If another high
rate monitor is connected we may need to reduce the bandwidth it
consumes so that it fits into the total 40 Gb/s available on the
Thunderbolt fabric.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To perform proper Display Port tunneling for Thunderbolt 3 devices we
need to allocate DP resources for DP IN port before they can be used.
The reason for this is that the user can also connect a monitor directly
to the Type-C ports in which case the Thunderbolt controller acts as
re-driver for Display Port (no tunneling takes place) taking the DP
sinks away from the connection manager. This allocation is done using
special sink allocation registers available through the link controller.
We can pair DP IN to DP OUT only if
* DP IN has sink allocated via link controller
* DP OUT port receives hotplug event
For DP IN adapters (only for the host router) we first query whether
there is DP resource available (it may be the previous instance of the
driver for example already allocated it) and if it is we add it to the
list. We then update the list when after each plug/unplug event to a DP
IN/OUT adapter. Each time the list is updated we try to find additional
DP IN <-> DP OUT pairs for tunnel establishment. This strategy also
makes it possible to establish another tunnel in case there are 3
monitors connected and one gets unplugged releasing the DP IN adapter
for the new tunnel.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Titan Ridge needs an additional connection manager handshake in order to
do proper Display Port tunneling so implement it here.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Lane bonding allows aggregating two 10/20 Gb/s (depending on the
generation) lanes into a single 20/40 Gb/s bonded link. This allows
sharing the full bandwidth more efficiently. In order to establish lane
bonding we need to check that lane bonding is possible through link
controller and that both ends of the link actually supports 2x widths.
This also means that all the paths should be established through the
primary port so update tb_path_alloc() to handle this as well.
Lane bonding is supported starting from Falcon Ridge (2nd generation)
controllers.
We also expose the current speed and number of lanes under each device
except the host router following similar attribute naming than USB bus.
Expose speed and number of lanes for both directions to allow possibility
of asymmetric link in the future.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that USB4 spec has names for these DP adapter registers we can use
them instead. This makes it easier to match certain register to the spec.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that USB4 spec has names for these PCIe adapter registers we can use
them instead. This makes it easier to match certain register to the spec.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now that USB4 spec has names for these basic registers we can use them
instead. This makes it easier to match certain register to the spec.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In addition to PCIe and Display Port tunnels it is also possible to
create tunnels that forward DMA traffic from the host interface adapter
(NHI) to a NULL port that is connected to another domain through a
Thunderbolt cable. These tunnels can be used to carry software messages
such as networking packets.
To support this we introduce another tunnel type (TB_TUNNEL_DMA) that
supports paths from NHI to NULL port and back.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Display Port tunnels are somewhat more complex than PCIe tunnels as it
requires 3 tunnels (AUX Rx/Tx and Video). In addition we are not
supposed to create the tunnels immediately when a DP OUT is enumerated.
Instead we need to wait until we get hotplug event to that adapter port
or check if the port has HPD set before tunnels can be established. This
adds Display Port tunneling support to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
NFC (non flow control) credits is actually 20-bit field so update
tb_port_add_nfc_credits() to handle this properly. This allows us to set
NFC credits for Display Port path in subsequent patches.
Also make sure the function does not update the hardware if the
underlying switch is already unplugged.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To be able to tunnel non-PCIe traffic, separate tunnel functionality
into generic and PCIe specific parts. Rename struct tb_pci_tunnel to
tb_tunnel, and make it hold an array of paths instead of just two.
Update all the tunneling functions to take this structure as parameter.
We also move tb_pci_port_active() to switch.c (and rename it) where we
will be keeping all port and switch related functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We need to wait until all buffers have been drained before the path can
be considered disabled. Do this for every hop in a path.
This adds another bit field to struct tb_regs_hop even if we are trying
to get rid of them but we can clean them up another day.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Thunderbolt 2 devices and beyond link controller needs to be notified
when a switch is going to be suspended by setting bit 31 in LC_SX_CTRL
register. Add this functionality to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Thunderbolt 2 devices and beyond need to have additional bits set in
link controller specific registers. This includes two bits in LC_SX_CTRL
that tell the link controller which lane is connected and whether it is
upstream facing or not.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We will be adding more link controller functionality in subsequent
patches and it does not make sense to keep all that in switch.c, so
separate LC functionality into its own file.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel has done pretty major changes to the driver and we continue to do
so in the future as well. Add Intel as copyright holder of the files we
have done changes.
While there drop "Cactus Ridge" from the headers because this driver
works also with other Thunderbolt controllers.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes small variable name typo and the associated
checkpatch spelling warning.
Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Organization of the capabilities in switches and ports is not so random
after all. Rework the capability handling functionality so that it
follows how capabilities are organized and provide two new functions
(tb_switch_find_vse_cap() and tb_port_find_cap()) which can be used to
extract capabilities for ports and switches. Then convert the current
users over these.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix typo in tb_cfg_print_error() message. Fix bytecount in struct
tb_drom_entry_port comment. Replace magic number in tb_switch_alloc().
Rename tb_sw_set_unpplugged() and TB_CAL_IECS to fix typos.
[bhelgaas: no functional change intended]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Every thunderbolt device consists (logically) of a switch with multiple
ports. Every port contains up to four config regions (HOPS, PORT,
SWITCH, COUNTERS) which are used to configure the device.
The tb_regs.h file contains all known registers and capabilities from
these config regions.
Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
