With the introduction of ACPI scan handlers, an ACPI device object
with an ACPI scan handler attached to it must not be bound to an ACPI
driver any more. Therefore it doesn't make sense to match those
ACPI device objects against a newly registered ACPI driver in
acpi_bus_match(), so make that function return 0 if the device
object passed to it has an ACPI scan handler attached.
This also addresses a regression related to a broken ACPI table in
the BIOS, where it has defined a _ROM method under the PCI root
bridge object. This causes the video module to treat that object
as a display controller device (since only display devices are
supposed to have a _ROM method defined according to the ACPI spec).
As a result, the ACPI video driver binds to the PCI root bridge
object and overwrites the previously assigned driver_data field of
it, causing subsequent calls to acpi_get_pci_dev() to fail.
[rjw: Subject and changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091
Reported-by: Jason Cassell <bluesloth600@gmail.com>
Reported-and-bisected-by: Dmitry S. Demin <dmitryy.demin@gmail.com>
Cc: 3.9+ <stable@kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix to return a negative error code in the acpi_gsi_to_irq() and
request_irq() error handling case instead of 0, as done elsewhere
in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 4b31e774 (Always set P-state on initialization) fixed bug
#4634 and caused the driver to always set the target P-State at
least once since the initial P-State may not be the desired one.
Commit 5a1c0228 (cpufreq: Avoid calling cpufreq driver's target()
routine if target_freq == policy->cur) caused a regression in
this behavior.
This fixes the regression by setting policy->cur based on the CPU's
target frequency rather than the CPU's current reported frequency
(which may be different). This means that the P-State will be set
initially if the CPU's target frequency is different from the
governor's target frequency.
This fixes an issue where setting the default governor to
performance wouldn't correctly enable turbo mode on all cores.
Signed-off-by: Ross Lagerwall <rosslagerwall@gmail.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.8+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking fixes from David Miller:
1) Fix timeouts with direct mode authentication in mac80211, from
Stanislaw Gruszka.
2) Aggregation sessions can deadlock in ath9k, from Felix Fietkau.
3) Netfilter's xt_addrtype doesn't work with ipv6 due to route lookups
creating undesirable cache entries, from Florian Westphal.
4) Fix netfilter's ipt_ULOG from generating non-NULL terminated
strings.
5) Fix netdev transmit queue crashes in mac80211, from Johannes Berg.
6) Fix copy and paste error in 802.11 stack that broke reporting of
64-bit station tx statistics, from Felix Fietkau.
7) When qlge_probe fails, it leaks the netdev. Fix from Wei Yongjun.
8) SKB control block (where we store the IP options information,
amongst other things) must be cleared properly otherwise ICMP
sending can crash for IP tunnels. Fix from Eric Dumazet.
9) Verification of Energy Efficient Ether support was coded wrongly,
the test was inversed. Fix from Giuseppe CAVALLARO.
10) TCP handles redirects improperly because the wrong flow key is used
for the route lookup. From Michal Kubecek.
11) Don't interpret MSG_CMSG_COMPAT from userspace, fix from Andy
Lutomirski.
12) The new AF_VSOCK was missing from the lockdep string table, fix from
Federico Vaga.
13) be2net doesn't handle checksumming of IP fragments properly, from
Somnath Kotur.
14) Fix several bugs in the device address list code that lead to
crashes and other misbehaviors. From Jay Vosburgh.
15) Fix ipv6 segmentation handling of fragmented GRE tunnel traffic,
from Pravin B Shalr.
16) Fix usage of stale policies in IPSEC layer, from Paul Moore.
17) Fix team driver dump of ports when there are a large number of them,
from Jiri Pirko.
18) Fix softlockups in UDP ipv4 socket lookup causes by and error in the
hlist_nulls_for_each_entry_rcu() macro. From Eric Dumazet.
19) Fix several regressions added by the high rate accuracy changes to
the htb packet scheduler. From Eric Dumazet.
20) Fix DMA'ing onto the stack in esd_usb2 and peak_usb CAN drivers,
from Olivier Sobrie and Marc Kleine-Budde.
21) Fix unremovable network devices due to missing route pointer
installation in the per-device ipv6 address list entries. From Gao
feng.
22) Apply the tg3 5719 DMA workaround on 5720 chips as well, otherwise
we get stalls. From Nithin Sujir.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits)
net_sched: htb: do not mix 1ns and 64ns time units
net: fix sk_buff head without data area
tg3: Add read dma workaround for 5720
net: ethernet: xilinx_emaclite: set protocol selector bits when writing ANAR
bnx2x: Fix bridged GSO for 57710/57711 chips
net: fec: add fallback to random MAC address
bnx2x: fix TCP offload for tunneling ipv4 over ipv6
ipv6: assign rt6_info to inet6_ifaddr in init_loopback
net/mlx4_core: Keep VF assigned MAC in the PF admin table
net/mlx4_en: Handle unassigned VF MAC address correctly
net/mlx4_core: Return -EPROBE_DEFER when a VF is probed before PF is sufficiently initialized
net/mlx4_en: Fix adaptive moderation cq update
net: can: peak_usb: Do not do dma on the stack
net: can: esd_usb2: Do not do dma on the stack
net: can: kvaser_usb: fix reception on "USBcan Pro" and "USBcan R" type hardware.
net_sched: restore "overhead xxx" handling
net: force a reload of first item in hlist_nulls_for_each_entry_rcu
hyperv: Fix vlan_proto setting in netvsc_recv_callback()
team: fix port list dump for big number of ports
list: introduce list_first_entry_or_null
...
The sahara crypto driver has an incorrect MODULE_DEVICE_TABLE, which
prevents us from actually building this driver as a loadable module.
sahara_dt_ids is a of_device_id array, so we have to use
MODULE_DEVICE_TABLE(of, ...).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It appears that the performance of 'vpgatherdd' is suboptimal for this kind of
workload (tested on Core i5-4570) and causes blowfish-avx2 to be significantly
slower than blowfish-amd64. So disable the AVX2 implementation to avoid
performance regressions.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It appears that the performance of 'vpgatherdd' is suboptimal for this kind of
workload (tested on Core i5-4570) and causes twofish_avx2 to be significantly
slower than twofish_avx. So disable the AVX2 implementation to avoid
performance regressions.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Error out of ecryptfs_fsync() if filemap_write_and_wait() fails.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Paul Taysom <taysom@chromium.org>
Cc: Olof Johansson <olofj@chromium.org>
Cc: stable@vger.kernel.org # v3.6+
Multiple nouveau regression fixes, hdmi audio, s/r and dac load detection
* 'drm-nouveau-fixes-3.10' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nv50/kms: use dac loadval from vbios, where it's available
drm/nv50/disp: force dac power state during load detect
drm/nv50-nv84/fifo: fix resume regression introduced by playlist race fix
drm/nv84/disp: Fix HDMI audio regression
Daniel writes:
Three regression fixes and one no-lvds quirk update. The regression Egbert
Eich tracked down goes back to 2.6.37 ... ugh. The other two are pretty
minor: One bogus modeset state checker WARN and a patch to prevent X
dying in a SIGBUS after a gpu hang with failed (or not implement as on
gen2/3) gpu reset.
* tag 'drm-intel-fixes-2013-06-04' of git://people.freedesktop.org/~danvet/drm-intel: (368 commits)
drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC.
drm/i915: no lvds quirk for hp t5740
drm/i915: Quirk the pipe A quirk in the modeset state checker
drm/i915: Fix spurious -EIO/SIGBUS on wedged gpus
Linux 3.10-rc4
parisc: parport0: fix this legacy no-device port driver!
parport_pc: disable PARPORT_PC_SUPERIO on parisc architecture
parisc/PCI: lba: fix: convert to pci_create_root_bus() for correct root bus resources (v2)
parisc/PCI: Set type for LBA bus_num resource
MAINTAINERS: update parisc architecture file list
parisc: kernel: using strlcpy() instead of strcpy()
parisc: rename "CONFIG_PA7100" to "CONFIG_PA7000"
parisc: fix kernel BUG at arch/parisc/include/asm/mmzone.h:50
parisc: memory overflow, 'name' length is too short for using
powerpc/cputable: Fix typo on P7+ cputable entry
powerpc/perf: Add missing SIER support
powerpc/perf: Revert to original NO_SIPR logic
powerpc/pci: Remove the unused variables in pci_process_bridge_OF_ranges
powerpc/pci: Remove the stale comments of pci_process_bridge_OF_ranges
powerpc/pseries: Always enable CONFIG_HOTPLUG_CPU on PSERIES SMP
...
Alex writes:
Just a few fixes for radeon. The big one is a fix for hangs on older
asics due to the ordering of interrupt initialization.
* 'drm-fixes-3.10' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: don't allow audio on DCE6
drm/radeon: Use direct mapping for fast fb access on RS780/RS880 (v2)
radeon: Fix system hang issue when using KMS with older cards
Regression from merging the old nv50/nvd9 code together, and may be
needed to fully fix fdo#64904.
The value is ignored completely by the hardware starting from nva3.
Reported-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Maarten Maathuis <madman2003@gmail.com>
Reported-by: Sven Joachim <svenjoac@gmx.de>
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Code refactoring in commit 8e9e3d2dea
(drm/nv84/disp: move hdmi control into core) disabled HDMI audio on my
nv84 by removing too much old code without adding it in the new one.
This patch adds the missing code within the new code layout resulting in
HDMI audio working again.
It should work on any HDMI head, but due to lacking ahrdware I could
only test the (1st) one.
It also might be possible that similar code is needed for nva3, which I
can't test.
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
commit 56b765b79 ("htb: improved accuracy at high rates") added another
regression for low rates, because it mixes 1ns and 64ns time units.
So the maximum delay (mbuffer) was not 60 second, but 937 ms.
Lets convert all time fields to 1ns as 64bit arches are becoming the
norm.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet spotted that we have to check skb->head instead
of skb->data as skb->head points to the beginning of the
data area of the skbuff. Similarly, we have to initialize the
skb->head pointer, not skb->data in __alloc_skb_head.
After this fix, netlink crashes in the release path of the
sk_buff, so let's fix that as well.
This bug was introduced in (0ebd0ac net: add function to
allocate sk_buff head without data area).
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 091f0ea300 "tg3: Add New 5719 Read
DMA workaround" added a workaround for TX DMA stall on the 5719. This
workaround needs to be applied to the 5720 as well.
Cc: stable@vger.kernel.org
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the protocol selector bits (4:0) of the PHY's MII_ADVERTISE
register (ANAR) when writing ADVERTISE_ALL. The protocol selector bits are
indicating IEEE 803.3u support and are fixed / read-only on some PHYs. Not
setting them correctly on others (like TI DP83630) makes the PHY fall back
to 10M HDX mode which should be avoided.
Tested for TI DP83630 PHY on Microblaze platform.
Signed-off-by: Jens Renner <renner@efe-gmbh.de>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently found out that GSO on 57710/57711 was broken, due to packets
being sent without a valid IP checksum.
Commit 057cf65 "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this
issue, but failed to set the correct IP checksum when receiving GSO packets
via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed
to calculate IP checksum were erroneously set in the incorrect
buffer descriptor.
This patch re-enables GSO in said scenario for 57710/57711 chips.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull input fixes from Dmitry Torokhov:
"Just a 2 small driver fixups here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - fix a typo for Cintiq 22HDT
Input: synaptics - fix sync lost after resume on some laptops
Pull kvm bugfixes from Gleb Natapov:
"The bulk of the fixes is in MIPS KVM kernel<->userspace ABI. MIPS KVM
is new for 3.10 and some problems were found with current ABI. It is
better to fix them now and do not have a kernel with broken one"
* 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Fix race in apic->pending_events processing
KVM: fix sil/dil/bpl/spl in the mod/rm fields
KVM: Emulate multibyte NOP
ARM: KVM: be more thorough when invalidating TLBs
ARM: KVM: prevent NULL pointer dereferences with KVM VCPU ioctl
mips/kvm: Use ENOIOCTLCMD to indicate unimplemented ioctls.
mips/kvm: Fix ABI by moving manipulation of CP0 registers to KVM_{G,S}ET_ONE_REG
mips/kvm: Use ARRAY_SIZE() instead of hardcoded constants in kvm_arch_vcpu_ioctl_{s,g}et_regs
mips/kvm: Fix name of gpr field in struct kvm_regs.
mips/kvm: Fix ABI for use of 64-bit registers.
mips/kvm: Fix ABI for use of FPU.
Pull gfs2 fixes from Steven Whitehouse:
"There are four patches this time.
The first fixes a problem where the wrong descriptor type was being
written into the log for journaled data blocks.
The second fixes a race relating to the deallocation of allocator
data.
The third provides a fallback if kmalloc is unable to satisfy a
request to allocate a directory hash table.
The fourth fixes the iopen glock caching so that inodes are deleted in
a more timely manner after rmdir/unlink"
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Don't cache iopen glocks
GFS2: Fall back to vmalloc if kmalloc fails for dir hash tables
GFS2: Increase i_writecount during gfs2_setattr_size
GFS2: Set log descriptor type for jdata blocks
Pull fuse fixes from Miklos Szeredi:
"One patch fixes an Oops introduced in 3.9 with the readdirplus
feature. The rest are fixes for async-dio in 3.10"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix alignment in short read optimization for async_dio
fuse: return -EIOCBQUEUED from fuse_direct_IO() for all async requests
fuse: fix readdirplus Oops in fuse_dentry_revalidate
fuse: update inode size and invalidate attributes on fallocate
fuse: truncate pagecache range on hole punch
fuse: allocate for_background dio requests based on io->async state
Add entry for the iSER initiator driver and which is maintained by Or
Gerlitz and Roi Dayan below the kernel InfiniBand subsystem.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add Mellanox copyright to the iser initiator source code which I maintain.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Change the code to destroy the "last opened" rdma_cm id after making
sure we released all other objects (QP, CQs, PD, etc) associated with
the IB device.
Since iser accesses the IB device using the rdma_cm id, we need to
free any objects that are related to the device that is associated
with the rdma_cm id prior to destroying that id. When this isn't
done, the low level driver that created this device can be unloaded
before iser has a chance to free all the objects and a such a call may
invoke code segment which isn't valid any more and crash.
Cc: Sean Hefty <sean.hefty@intel.com
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull microblaze fixes from Michal Simek:
"One is fixing warning reported by sparse and the second warning was
reported by Geert in his build regressions/improvements status update
for -rc4."
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Use static inline functions in cacheflush.h
microblaze: Fix sparse warnings
If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW was initialized with data from wrong header, this caused TSO packets
have wrong IP csum.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 25fb6ca4ed
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
forgot to assign rt6_info to the inet6_ifaddr.
When disable the net device, the rt6_info which allocated
in init_loopback will not be destroied in __ipv6_ifa_notify.
This will trigger the waring message below
[23527.916091] unregister_netdevice: waiting for tap0 to become free. Usage count = 1
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here are there fixes for the v3.10 release cycle:
The first patch by Jonas Peterson and Olivier Sobrie fixes the reception of CAN
frames on Kvaser's "USBcan Pro" and "USBcan R" type hardware.
The last two patches by Olivier Sobrie (for esd_usb2) and me (for peak_usb)
change the memory handling for the USB messages from stack to kmalloc(), as
memory used for DMA should not be allocated on stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC addresses assigned by the PF to VFs were not kept in the PF driver
admin table. As a result, displaying the VF MACs from the PF interface
to user space showed zero address where in fact the VF got non-zero
address from the PF, fix that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF sense they didn't get MAC address, use random one. This will
address the case of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the PF initialization, SRIOV is enabled before the PF is fully initialized.
This allows the kernel to probe the newly-exposed VFs before the PF is ready
to handle them (nested probes).
Have the probe method return the -EPROBE_DEFER value in this situation (instead
of the VF probe method retrying its initialization in a loop, and returning -EIO
on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel
itself will retry the probe after a suitable delay.
Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When turning on adaptive_rx under adaptive moderation, the CQ's moderation
count wasn't updated according to rx_frames which resulted in too many
interrupts and bandwidth drop.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of little bits and pieces, some delayed due to traveling.
1) A memory leak fix in the callback buffer.
2) Wrong exit path due to a return when it should have been a goto.
3) Bug in a mask value in ad4350
4) Reading the wrong value in raw to processed utility function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=5y7r
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.10b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second round of IIO fixes for the 3.10 cycle.
A couple of little bits and pieces, some delayed due to traveling.
1) A memory leak fix in the callback buffer.
2) Wrong exit path due to a return when it should have been a goto.
3) Bug in a mask value in ad4350
4) Reading the wrong value in raw to processed utility function.
Current HSPI driver is using msleep(20) on hspi_status_check_timeout(),
but it was too long delay for SPI device.
Bock-W board SPI access was too slow without this patch.
This patch uses udelay(10) for it.
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ISR currently consumes the rx buffer data and re-enables transmission
from within interrupt context. This is bad because if the interrupt
occurs again before the ISR exits, the new interrupt will be erroneously
cleared by the still completing ISR.
Simplified the ISR by just setting the completion variable and exiting with
no action. Then just looped the transmit functionality in
xilinx_spi_txrx_bufs().
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
