In recent allwinner kernel sources the mmc clk-delay settings have been
slightly tweaked, and for sun9i they are completely different then what
we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (introduced in A23 sdk)
This also drops the clk-delay calculation for clocks > 50 MHz, we do
not need this as we've: mmc->f_max = 50000000, and the delays in the
old code were not correct (at 100 MHz the delay must be a multiple of 60,
at 200 MHz a multiple of 120).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that support for platforms which have optional regulator is added,
remove CONFIG_REGULATOR check in omap_hsmmc.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
vdd voltage is set in mmc core to ios->vdd and vmmc should actually
be set to this voltage. Modify omap_hsmmc_enable_supply
to not take vdd as argument since now it's directly set to
the voltage in ios->vdd.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use regulator_is_enabled of pbias regulator to find pbias regulator
status instead of maintaining a custom bookkeeping
pbias_enabled variable.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
enable vmmc_aux regulator only if it is in disabled state and disable
vmmc_aux regulator only if it is in enabled state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the regulator is enabled on boot (checked using regulator_is_enabled),
invoke regulator_enable() so that the usecount reflects the correct
state of the regulator and then disable the regulator so that the
initial state of the regulator is disabled. Avoid using ->set_power,
since set_power also takes care of setting the voltages which is not
needed at this point.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix omap_hsmmc_set_power so that pbias regulator is not enabled
during power off.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions to set pbias and invoke it from omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Cleanup omap_hsmmc_set_power by adding separate
functions for enable/disable supply and invoke it from
omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return error if any of the regulator APIs (regulator_enable,
regulator_disable, regulator_set_voltage) fails in
omap_hsmmc_set_power to avoid undefined behavior.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the unnecessary pbias regulator_set_voltage done after
pbias regulator_disable in omap_hsmmc_set_power.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Instead of using omap_hsmmc_host's vcc and vcc_aux
members, use vmmc and vqmmc present in mmc_host which is present
for the same purpose.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the vmmc regulator provides a valid ocrmask, use it. By this even if
the pdata has a valid ocrmask, it will be overwritten with the ocrmask
of the vmmc regulator.
Also remove the unnecessary compatibility check between the ocrmask in
the pdata and the ocrmask from the vmmc regulator.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No functional change. Instead of using a local regulator variable
in omap_hsmmc_reg_get() for holding the return value of
devm_regulator_get_optional() and then assigning to omap_hsmmc_host
regulator members: vcc, vcc_aux and pbias, directly use the
omap_hsmmc_host regulator members.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now return error only if the return value of
devm_regulator_get_optional() is not the same as -ENODEV, since with
-EPROBE_DEFER, the regulator can be obtained later and all other
errors are fatal.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since vmmc can be optional for some platforms, use
devm_regulator_get_optional() for vmmc. Now return error only
if the return value of devm_regulator_get_optional() is not the
same as -ENODEV, since with -EPROBE_DEFER, the regulator can be
obtained later and all other errors are fatal.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: ludovic.desroches@atmel.com <ludovic.desroches@atmel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock should be enable when SDHI registers are accessed.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Propagate error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intent appears to be to clear only the bits which are set in status
(by setting them to zero in the ack write), like in the other interrupt
handlers, and not to always clear everything (by always writing zero).
Use the correct not operator.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->sg is only set when we're transferring multiple blocks. Check for
its availibility before dereferencing it in the timeout work debug
print.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We ignore errors from mmc_regulator_get_supply() because the usage of
the regulators is optional for the driver, but we still need to check
for and handle EPROBE_DEFER, like it's done in for example dw_mmc.
Otherwise we might end up not using the specified regulators just
because of probe order.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds the compatible string in sdhci-of-arasan.c to
support sdhci-arasan5.1 version of controller. No documented
controller IP version is found in the TRM, so we use ths version
of command queueing engine integrated into this controller by arasan
to specify our controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit bb8175a8aa ("mmc: sdhci: clarify DDR timing mode between
SD-UHS and eMMC") added MMC_DDR52 as eMMC's DDR mode to be
distinguished from SD-UHS, but it missed setting driver type for
MMC_DDR52 timing mode.
So sometimes we get the following error on Marvell BG2Q DMP board:
[ 1.559598] mmcblk0: error -84 transferring data, sector 0, nr 8, cmd
response 0x900, card status 0xb00
[ 1.569314] mmcblk0: retrying using single block read
[ 1.575676] mmcblk0: error -84 transferring data, sector 2, nr 6, cmd
response 0x900, card status 0x0
[ 1.585202] blk_update_request: I/O error, dev mmcblk0, sector 2
[ 1.591818] mmcblk0: error -84 transferring data, sector 3, nr 5, cmd
response 0x900, card status 0x0
[ 1.601341] blk_update_request: I/O error, dev mmcblk0, sector 3
This patches fixes this by adding the missing driver type setting.
Fixes: bb8175a8aa ("mmc: sdhci: clarify DDR timing mode ...")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 250ms timeout is too short.
On my system enabling the oclk takes under 50ms and disabling slightly
over 100ms when idle. Under load disabling the clock can take over
350ms.
This does not make mmc clock gating look like good option to have on
sunxi but the system should not crash with mmc clock gating enabled
nonetheless.
This patch sets the timeout to 750ms.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the current quirk set is for an old FPGA, and this patch corrects
quirks according to real SoC.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By default, for all imx SoC types, the watermark level is 16, and the
burst length is 8. But if the SDIO/SD/MMC I/O speed is fast enough,
this default watermark level and burst length will be the performance
bottleneck.
For example, i.MX7D support eMMC HS400 mode, this mode can run in 8 bit,
200MHZ DDR mode. So the I/O speed improve a lot compare to SD3.0.
The default burst length is 8, if we don't change this value, in
HS400 mode, when we do eMMC read operation, we can find that the
clock signal will stop for a period of time. This means the speed
of data moving on AHB bus is slower than I/O speed. So we should
improve the speed of data moving on AHB bus.
This patch set the default burst length as 16, and set the default
watermark level as 64. The test result is the clock signal has
no stop during the eMMC HS400 operation.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently we find that if a usdhc is choosed to boot system, then ROM
code will set the burst length enable bit of this usdhc as 0.
This will make performance drop a lot if this usdhc's burst length is
configed. So this patch set back the burst_length_enable bit as 1,
which is the default value, and means burst length is enabled for INCR.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tuning-step is the delay cell steps in tuning procedure. The default value
of tuning-step is 1. Some boards or cards need another value to pass the
tuning procedure. For example, imx7d-sdb board need the tuning-step value
as 2, otherwise it can't pass the tuning procedure.
So this patch add the tuning-step setting in driver, so that user can set
the tuning-step value in dts.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.
So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For eSDHC(version < 2.3), the pre divider only could divide base clock
by 2 at least. Add workaround for this to avoid unexpected issue.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Fixes: bd455029d0 ("mmc: sdhci-of-esdhc: Pre divider starts at 1")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently one mrq->data maybe execute dma_map_sg() twice
when mmc subsystem prepare over one new request, and the
following log show up:
sdhci[sdhci_pre_dma_transfer] invalid cookie: 24, next-cookie 25
In this condition, mrq->date map a dma-memory(1) in sdhci_pre_req
for the first time, and map another dma-memory(2) in sdhci_prepare_data
for the second time. But driver only unmap the dma-memory(2), and
dma-memory(1) never unmapped, which cause the dma memory leak issue.
This patch use another method to map the dma memory for the mrq->data
which can fix this dma memory leak issue.
Fixes: 348487cb28 ("mmc: sdhci: use pipeline mmc requests to improve performance")
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixes MMC not working issue on O2Micro/BayHub Host, which
requires transfer mode register to be cleared when sending no DMA
command.
Signed-off-by: Peter Guo <peter.guo@bayhubtech.com>
Signed-off-by: Adam Lee <adam.lee@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the problem which timeout occurs at the time of command request with
several cards.
The timeout value was insufficient as a verification of several cards,
so it was changed 5 seconds from 2 seconds.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci
compliant controller.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In programmable mode, if the clock frequency is too high, the divider
can be too small to meet the clock frequency requirement especially to
init the SD card. In this case, switch to the divided clock mode.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add a new quirk to add a s/w timer to notify the driver
to terminate current transfer and report a data timeout to the core,
if DTO interrupt does NOT come within the given time.
dw_mmc call mmc_request_done func to finish transfer depends on
DTO interrupt. If DTO interrupt does not come in sending data state,
the current transfer will be blocked.
We got the reply from synopsys:
There are two counters but both use the same value of [31:8] bits.
Data timeout counter doesn't wait for stop clock and you should get
DRTO even when the clock is not stopped.
Host Starvation timeout counter is triggered with stop clock condition.
This means that host should get DRTO and DTO interrupt.
But this case really exists, when driver reads tuning data from
card on RK3288-pink2 board. I measured waveforms by oscilloscope
and found that card clock was always on and data lines were always
holded high level in sending data state.
There are two possibility that data over interrupt doesn't come in
reading data state on RK3X SoCs:
- get command done interrupt, but doesn't get any data-related interrupt.
- get data error interrupt, but doesn't get data over interrupt.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
The dw_mci_init_dma() may decide to not use dma, but pio instead, caused
by things like wrong dma settings in the system.
Till now the code dw_mci_init_slot() always assumed that dma is available
when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var
set during dma init.
So when now the dma init failed for whatever reason, the transfer sizes
would still be set for dma transfers, especially including the maximum
block-count calculated from host->ring_size and resulting in a
[ 4.991109] ------------[ cut here ]------------
[ 4.991111] kernel BUG at drivers/mmc/core/core.c:256!
[ 4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM
because host->ring_size is 0 in this case and the slot init code uses
the wrong code to calculate the values.
Fix this by selecting the correct calculations using the host->use_dma
variable instead of the CONFIG_MMC_DW_IDMAC config option.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This patch fixes the following issues reported by checkpatch.pl:
- use -EINVAL instead of -ENOSYS, to fix warning message:
"ENOSYS means 'invalid syscall nr' and nothing else"
- split lines whose length is greater than 80 characters
- avoid quoted string split across lines
- use min_t instead of min, to fix warning message:
"min() should probably be min_t(int, cnt, host->part_buf_count)"
- fix missing a blank line after declarations
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
As per DW MobileStorage databook "each descriptor can transfer up to 4kB
of data in chained mode", moreover buffer size that is put in "des1" is
limited to 13 bits, i.e. for example on attempt to
IDMAC_SET_BUFFER1_SIZE(desc, 8192) size value that's effectively written
will be 0.
On the platform with 8kB PAGE_SIZE I see dw_mmc gets data blocks in
SG-list of 8kB size and that leads to unpredictable behavior of the
SD/MMC controller.
In particular on write to FAT partition of SD-card the controller will
stuck in the middle of DMA transaction.
Solution to the problem is simple - we need to pass large (> 4kB) data
buffers to the controller via multiple descriptors. And that's what
that change does.
What's interesting I did try original driver on same platform but
configured with 4kB PAGE_SIZE and may confirm that data blocks passed
in SG-list to dw_mmc never exeed 4kB limit - that explains why nobody
ever faced a problem I did.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
eSDHC supports high speed mode, but has no enabling bit for it.
Add this quirk to avoid writing to eSDHC_PROCTL[DTW] by mistake.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If no pdata.set_power was set by the platform code, the driver
was updating pdata with its own fallback function. This is a no-no
since pdata shall be read-only.
This patch pushes the check 'pdata->set_power != NULL' down into
the fallback functions. If pdata.set_power is really set, it calls them
and exits, otherwise the fallback code is used.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Controller could have both NO_CARD_NO_RESET and BROKEN_CARD_DETECTION
quirks set. Use sdhci_do_get_cd() when applying NO_CARD_NO_RESET, which
properly check for BROKEN_CARD_DETECTION quirk.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>