Bcache only does recoverable I/O for read operations by calling
cached_dev_read_error(). For write opertions there is no I/O recovery for
failed requests.
But in bch_count_io_errors() no matter read or write I/Os, before errors
counter reaches io error limit, pr_err() always prints "IO error on %,
recoverying". For write requests this information is misleading, because
there is no I/O recovery at all.
This patch adds a parameter 'is_read' to bch_count_io_errors(), and only
prints "recovering" by pr_err() when the bio direction is READ.
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the control system would wait for at least half a second, and there's
been no reqs hitting the backing disk for awhile: use an alternate mode
where we have at most one contiguous set of writebacks in flight at a
time. (But don't otherwise delay). If front-end IO appears, it will
still be quick, as it will only have to contend with one real operation
in flight. But otherwise, we'll be sending data to the backing disk as
quickly as it can accept it (with one op at a time).
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Writeback keys are presently iterated and dispatched for writeback in
order of the logical block address on the backing device. Multiple may
be, in parallel, read from the cache device and then written back
(especially when there are contiguous I/O).
However-- there was no guarantee with the existing code that the writes
would be issued in LBA order, as the reads from the cache device are
often re-ordered. In turn, when writing back quickly, the backing disk
often has to seek backwards-- this slows writeback and increases
utilization.
This patch introduces an ordering mechanism that guarantees that the
original order of issue is maintained for the write portion of the I/O.
Performance for writeback is significantly improved when there are
multiple contiguous keys or high writeback rates.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Tested-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
in bch_debug_init(), ret is always 0, and the return value is useless,
change it to return 0 if be success after calling debugfs_create_dir(),
else return a non-zero value.
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bcache is the only user of bio_alloc_pages(), so move this function into
bcache, and avoid it being misused in the future.
Also rename it to bch_bio_allo_pages() since it is bcache only.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The time spent searching for things to write back "counts" for the
actual rate achieved, so don't flush the accumulated rate with each
chunk.
This will maintain better fidelity to user-commanded rates, but it
may slightly increase the burstiness of writeback. The writeback
lock needs improvement to help mitigate this.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The previous code artificially limited writeback rate to 1000000
blocks/second (NSEC_PER_MSEC), which is a rate that can be met on fast
hardware. The rate limiting code works fine (though with decreased
precision) up to 3 orders of magnitude faster, so use NSEC_PER_SEC.
Additionally, ensure that uint32_t is used as a type for rate throughout
the rate management so that type checking/clamp_t can work properly.
bch_next_delay should be rewritten for increased precision and better
handling of high rates and long sleep periods, but this is adequate for
now.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reported-by: Coly Li <colyli@suse.de>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This works in conjunction with the new PI controller. Currently, in
real-world workloads, the rate controller attempts to write back 1
sector per second. In practice, these minimum-rate writebacks are
between 4k and 60k in test scenarios, since bcache aggregates and
attempts to do contiguous writes and because filesystems on top of
bcachefs typically write 4k or more.
Previously, bcache used to guarantee to write at least once per second.
This means that the actual writeback rate would exceed the configured
amount by a factor of 8-120 or more.
This patch adjusts to be willing to sleep up to 2.5 seconds, and to
target writing 4k/second. On the smallest writes, it will sleep 1
second like before, but many times it will sleep longer and load the
backing device less. This keeps the loading on the cache and backing
device related to writeback more consistent when writing back at low
rates.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bcache uses a control system to attempt to keep the amount of dirty data
in cache at a user-configured level, while not responding excessively to
transients and variations in write rate. Previously, the system was a
PD controller; but the output from it was integrated, turning the
Proportional term into an Integral term, and turning the Derivative term
into a crude Proportional term. Performance of the controller has been
uneven in production, and it has tended to respond slowly, oscillate,
and overshoot.
This patch set replaces the current control system with an explicit PI
controller and tuning that should be correct for most hardware. By
default, it attempts to write at a rate that would retire 1/40th of the
current excess blocks per second. An integral term in turn works to
remove steady state errors.
IMO, this yields benefits in simplicity (removing weighted average
filtering, etc) and system performance.
Another small change is a tunable parameter is introduced to allow the
user to specify a minimum rate at which dirty blocks are retired.
There is a slight difference from earlier versions of the patch in
integral handling to prevent excessive negative integral windup.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If an IO operation fails, and we didn't successfully read data from the
cache, don't writeback invalid/partial data to the backing disk.
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bcache uses a Proportion-Differentiation Controller algorithm to control
writeback rate to cached devices. In the PD controller algorithm, dirty
stripes of thin flash device should not be counted in, because flash only
volumes never write back dirty data.
Currently dirty stripe counter for thin flash device is not initialized
when the thin flash device starts. Which means the following calculation
in PD controller will reference an undefined dirty stripes number, and
all cached devices attached to the same cache set where the thin flash
device lies on may have an inaccurate writeback rate.
This patch calles bch_sectors_dirty_init() in flash_dev_run(), to
correctly initialize dirty stripe counter when the thin flash device
starts to run. This patch also does following parameter data type change,
-void bch_sectors_dirty_init(struct cached_dev *dc);
+void bch_sectors_dirty_init(struct bcache_device *);
to call this function conveniently in flash_dev_run().
(Commit log is composed by Coly Li)
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
__update_write_rate() uses a Proportion-Differentiation Controller
algorithm to control writeback rate. A dirty target number is used in
this PD controller to control writeback rate. A larger target number
will make the writeback rate smaller, on the versus, a smaller target
number will make the writeback rate larger.
bcache uses the following steps to calculate the target number,
1) cache_sectors = all-buckets-of-cache-set * buckets-size
2) cache_dirty_target = cache_sectors * cached-device-writeback_percent
3) target = cache_dirty_target *
(sectors-of-cached-device/sectors-of-all-cached-devices-of-this-cache-set)
The calculation at step 1) for cache_sectors is incorrect, which does
not consider dirty blocks occupied by flash only volume.
A flash only volume can be took as a bcache device without cached
device. All data sectors allocated for it are persistent on cache device
and marked dirty, they are not touched by bcache writeback and garbage
collection code. So data blocks of flash only volume should be ignore
when calculating cache_sectors of cache set.
Current code does not subtract dirty sectors of flash only volume, which
results a larger target number from the above 3 steps. And in sequence
the cache device's writeback rate is smaller then a correct value,
writeback speed is slower on all cached devices.
This patch fixes the incorrect slower writeback rate by subtracting
dirty sectors of flash only volumes in __update_writeback_rate().
(Commit log composed by Coly Li to pass checkpatch.pl checking)
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Coly Li <colyli@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some drivers often use external bvec table, so introduce
this helper for this case. It is always safe to access the
bio->bi_io_vec in this way for this case.
After converting to this usage, it will becomes a bit easier
to evaluate the remaining direct access to bio->bi_io_vec,
so it can help to prepare for the following multipage bvec
support.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixed up the new O_DIRECT cases.
Signed-off-by: Jens Axboe <axboe@fb.com>
bio_free_pages is introduced in commit 1dfa0f68c0
("block: add a helper to free bio bounce buffer pages"),
we can reuse the func in other modules after it was
imported.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Separate the op from the rq_flag_bits and have bcache
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
bch_writeback_thread() is calling try_to_freeze(), but that's just an
expensive no-op given the fact that the thread is not marked freezable.
I/O helper kthreads, exactly such as the bcache writeback thread, actually
shouldn't be freezable, because they are potentially necessary for
finalizing the image write-out.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Previously, it would only scan the entire disk if it was starting from
the very start of the disk - i.e. if the previous scan got to the end.
This was broken by refill_full_stripes(), which updates last_scanned so
that refill_dirty was never triggering the searched_from_start path.
But if we change refill_dirty() to always scan the entire disk if
necessary, regardless of what last_scanned was, the code gets cleaner
and we fix that bug too.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
The bcache driver has always accepted arbitrarily large bios and split
them internally. Now that every driver must accept arbitrarily large
bios this code isn't nessecary anymore.
Cc: linux-bcache@vger.kernel.org
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: add more description in commit message]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
There were two issues here:
- writeback thread did not start until the device first became dirty
- writeback thread used uninterruptible sleep once running
Without this patch I see kernel warnings printed and a load average of
1.52 after booting my test VM. With this patch the warnings are gone and
the load average is near 0.00 as expected.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJSwLfoAAoJEHm+PkMAQRiGi6QH/1U1B7lmHChDTw3jj1lfm9gA
189Si4QJlnxFWCKHvKEL+pcaVuACU+aMGI8+KyMYK4/JfuWVjjj5fr/SvyHH2/8m
LdSK8aHMhJ46uBS4WJ/l6v46qQa5e2vn8RKSBAyKm/h4vpt+hd6zJdoFrFai4th7
k/TAwOAEHI5uzexUChwLlUBRTvbq4U8QUvDu+DeifC8cT63CGaaJ4qVzjOZrx1an
eP6UXZrKDASZs7RU950i7xnFVDQu4PsjlZi25udsbeiKcZJgPqGgXz5ULf8ZH8RQ
YCi1JOnTJRGGjyIOyLj7pyB01h7XiSM2+eMQ0S7g54F2s7gCJ58c2UwQX45vRWU=
=/4/R
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc6' into for-3.14/core
Needed to bring blk-mq uptodate, since changes have been going in
since for-3.14/core was established.
Fixup merge issues related to the immutable biovec changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Conflicts:
block/blk-flush.c
fs/btrfs/check-integrity.c
fs/btrfs/extent_io.c
fs/btrfs/scrub.c
fs/logfs/dev_bdev.c
The old writeback PD controller could get into states where it had throttled all
the way down and take way too long to recover - it was too complicated to really
understand what it was doing.
This rewrites a good chunk of it to hopefully be simpler and make more sense,
and it also pays more attention to units which should make the behaviour a bit
easier to understand.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
at the beginning (schedule_timout_interuptible) and others
do his on their own
This prevents wrong load average calculation (load of 1 per thread)
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Last of the btree_map() conversions. Main visible effect is
bch_btree_insert() is no longer taking a struct btree_op as an argument
anymore - there's no fancy state machine stuff going on, it's just a
normal function.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
When we convert bch_btree_insert() to bch_btree_map_leaf_nodes(), we
won't be passing struct btree_op to bch_btree_insert() anymore - so we
need a different way of returning whether there was a collision (really,
a replace collision).
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This is prep work for converting bch_btree_insert to
bch_btree_map_leaf_nodes() - we have to convert all its arguments to
actual arguments. Bunch of churn, but should be straightforward.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Lots of stuff has been open coding its own btree traversal - which is
generally pretty simple code, but there are a few subtleties.
This adds new new functions, bch_btree_map_nodes() and
bch_btree_map_keys(), which do the traversal for you. Everything that's
open coding btree traversal now (with the exception of garbage
collection) is slowly going to be converted to these two functions;
being able to write other code at a higher level of abstraction is a
big improvement w.r.t. overall code quality.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This simplifies the writeback flow control quite a bit - previously, it
was conceptually two coroutines, refill_dirty() and read_dirty(). This
makes the code quite a bit more straightforward.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Slowly working on pruning struct btree_op - the aim is for it to only
contain things that are actually necessary for traversing the btree.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Some refactoring - better to explicitly pass stuff around instead of
having it all in the "big bag of state", struct btree_op. Going to prune
struct btree_op quite a bit over time.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Originally I got this right... except that the divides didn't use
do_div(), which broke 32 bit kernels. When I went to fix that, I forgot
that the raid stripe size usually isn't a power of two... doh
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Background writeback works by scanning the btree for dirty data and
adding those keys into a fixed size buffer, then for each dirty key in
the keybuf writing it to the backing device.
When read_dirty() finishes and it's time to scan for more dirty data, we
need to wait for the outstanding writeback IO to finish - they still
take up slots in the keybuf (so that foreground writes can check for
them to avoid races) - without that wait, we'll continually rescan when
we'll be able to add at most a key or two to the keybuf, and that takes
locks that starves foreground IO. Doh.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of bcache's utility code has made it into the rest of the kernel,
so drop the bcache versions.
Bcache used to have a workaround for allocating from a bio set under
generic_make_request() (if you allocated more than once, the bios you
already allocated would get stuck on current->bio_list when you
submitted, and you'd risk deadlock) - bcache would mask out __GFP_WAIT
when allocating bios under generic_make_request() so that allocation
could fail and it could retry from workqueue. But bio_alloc_bioset() has
a workaround now, so we can drop this hack and the associated error
handling.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Now that we're tracking dirty data per stripe, we can add two
optimizations for raid5/6:
* If a stripe is already dirty, force writes to that stripe to
writeback mode - to help build up full stripes of dirty data
* When flushing dirty data, preferentially write out full stripes first
if there are any.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
To make background writeback aware of raid5/6 stripes, we first need to
track the amount of dirty data within each stripe - we do this by
breaking up the existing sectors_dirty into per stripe atomic_ts
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Previously, dirty_data wouldn't get initialized until the first garbage
collection... which was a bit of a problem for background writeback (as
the PD controller keys off of it) and also confusing for users.
This is also prep work for making background writeback aware of raid5/6
stripes.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
The tracepoints were reworked to be more sensible, and fixed a null
pointer deref in one of the tracepoints.
Converted some of the pr_debug()s to tracepoints - this is partly a
performance optimization; it used to be that with DEBUG or
CONFIG_DYNAMIC_DEBUG pr_debug() was an empty macro; but at some point it
was changed to an empty inline function.
Some of the pr_debug() statements had rather expensive function calls as
part of the arguments, so this code was getting run unnecessarily even
on non debug kernels - in some fast paths, too.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
