eeprom-length is a switch property, not a dsa property, and thus
needs to be attached to the switch node, not to the dsa node.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6793abb4e8 ("net: dsa: Add support for switch EEPROM access")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit da4759c (sysfs: Use only return value from is_visible for
the file mode), it is possible to reduce the permissions of a file.
So declare temp1_max with the DEVICE_ATTR_RW macro and remove the write
permission in dsa_hwmon_attrs_visible if set_temp_limit isn't provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to description in 'include/net/dsa.h', in cascade switches
configurations where there are more than one interconnected devices,
'rtable' array in 'dsa_chip_data' structure is used to indicate which
port on this switch should be used to send packets to that are destined
for corresponding switch.
However, dsa_of_setup_routing_table() fills 'rtable' with port numbers
of the _target_ switch, but not current one.
This commit removes redundant devicetree parsing and adds needed port
number as a function argument. So dsa_of_setup_routing_table() now just
looks for target switch number by parsing parent of 'link' device node.
To remove possible misunderstandings with the way of determining target
switch number, a corresponding comment was added to the source code and
to the DSA device tree bindings documentation file.
This was tested on a custom board with two Marvell 88E6095 switches with
following corresponding routing tables: { -1, 10 } and { 8, -1 }.
Signed-off-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide callbacks for ndo_fdb_add, ndo_fdb_del, and ndo_fdb_dump.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch. In that case, do nothing instead of asking
the switch driver to remove a port from a bridge that it didn't join.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bd76a11670 made all DSA drivers
depend on NET_DSA rather than selecting them. However, as the only way
to select this option was to actually select a driver, it made DSA
impossible to enable at all.
This patch adds an explicit entry which the user will have to enable
prior selecting a driver.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This would fix randconfig compile error:
net/built-in.o: In function `netdev_switch_fib_ipv4_abort':
(.text+0xf7811): undefined reference to `fib_flush_external'
Also it fixes following warnings:
warning: (NET_DSA) selects NET_SWITCHDEV which has unmet direct dependencies (NET && INET)
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6131 && NET_DSA_MV88E6123_61_65 && NET_DSA_MV88E6171 && NET_DSA_MV88E6352 && NET_DSA_BCM_SF2) selects NET_DSA which has unmet direct dependencies (NET && HAVE_NET_DSA && NET_SWITCHDEV)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move swdev wrappers over to new swdev ops (from previous ndo ops). No
functional changes to the implementation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
rocker: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
dsa: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cd28a1a9ba ("net: dsa: fully divert PHY reads/writes if
requested") introduced a check for particular PHYs that need to be
accessed using the slave MII bus created by DSA, but this check was too
inclusive. This would prevent fixed PHYs from being successfully
registered because those should not go through the slave MII bus created
by DSA.
Make sure we check that the PHY is not a fixed PHY to prevent that from
happening.
Fixes: cd28a1a9ba ("net: dsa: fully divert PHY reads/writes if requested")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a PHY is found via Device Tree, and is also flagged by the
switch driver as needing indirect reads/writes using the switch driver
implemented MDIO bus, make sure that we bind this PHY to the slave MII
bus in order for this to happen.
Without this, we would succeed in having the PHY driver probe()'s
function to use slave MII bus read/write functions, because this is done
during dsa_slave_mii_init(), but past that point, the PHY driver would
not go through these diverted reads and writes.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for dealing with indirect reads and writes towards
certain PHY devices, move the code which deals with binding the PHY
device to the slave MII bus created by DSA to its own function:
dsa_slave_phy_connect().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using of_find_device_by_node() restricts the search to platform_device that
match the specified device_node pointer. This is not even remotely true for
network devices backed by a pci_device for instance.
of_find_net_device_by_node() allows us to do a more thorough lookup to find the
struct net_device corresponding to a particular device_node pointer.
For symetry with the non-OF code path, we hold the net_device pointer in
dsa_probe() just like what dev_to_net_dev() does when we call this
function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the core logic that setups a 'struct dsa_switch_tree' and
removes it, update dsa_probe() and dsa_remove() to use the two helper
functions. This will be useful to allow for other callers to setup
this structure differently.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support the new DSA device driver model, a dsa_switch should
be able to advertise the type of tagging protocol supported by the
underlying switch device. This also removes constraints on how tagging
can be stacked to each other.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the part of dsa_switch_setup() which is responsible for allocating
and initializing a 'struct dsa_switch' and the part which is doing a
given switch device setup and slave network device creation.
This is a preliminary change to allow a separate caller of
dsa_switch_setup_one() which may have externally initialized the
dsa_switch structure, outside of dsa_switch_setup().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing a different model to register DSA switches,
update dsa_of_probe() and dsa_probe() to return -EPROBE_DEFER where
appropriate.
Failure to find a phandle or Device Tree property is still fatal, but
looking up the internal device structure associated with a Device Tree
node is something that might need to be delayed based on driver probe
ordering.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing a different mechanism to register DSA switch
devices and driver, update dsa_of_probe and dsa_of_remove to take a
struct device pointer since neither of these two functions uses the
struct platform_device pointer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid race conditions when using the ds->ports[] array,
we need to check if the accessed port has been initialized.
Introduce and use helper function dsa_is_port_initialized
for that purpose and use it where needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support bridging offloads in DSA switch drivers, select
NET_SWITCHDEV to get access to the port_stp_update and parent_get_id
NDOs that we are required to implement.
To facilitate the integratation at the DSA driver level, we implement 3
types of operations:
- port_join_bridge
- port_leave_bridge
- port_stp_update
DSA will resolve which switch ports that are currently bridge port
members as some Switch hardware/drivers need to know about that to limit
the register programming to just the relevant registers (especially for
slow MDIO buses).
We also take care of setting the correct STP state when slave network
devices are brought up/down while being bridge members.
Finally, when a port is leaving the bridge, we make sure we set in
BR_STATE_FORWARDING state, otherwise the bridge layer would leave it
disabled as a result of having left the bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A network device notifier can be called for one or more of the created
slave devices before all slave devices have been registered. This can
result in a mismatch between ds->phys_port_mask and the registered devices
by the time the call is made, and it can result in a slave device being
added to a bridge before its entry in ds->ports[] has been initialized.
Rework the initialization code to initialize entries in ds->ports[] in
dsa_slave_create. With this change, dsa_slave_create no longer needs
to return slave_dev but can return an error code instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the phy interface mode is not found in devicetree, or if devicetree
is not configured, of_get_phy_mode returns -ENODEV. The current code
sets the phy interface mode to the return value from of_get_phy_mode
without checking if it is valid.
This invalid phy interface mode is passed as parameter to of_phy_connect
or to phy_connect_direct. This sets the phy interface mode to the invalid
value, which in turn causes problems for any code using phydev->interface.
Fixes: b31f65fb43 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_phy_setup() finds the phy for the port via device tree and
using of_phy_connect(), or it uses the fall back of taking a phy from
the switch internal mdio bus and calling phy_connect_direct(). Either
way, if a phy is found, phy_attach_direct() is called to attach the
phy to the slave device.
In dsa_slave_create(), a second call to phy_attach() is made. This
results in the warning "PHY already attached". Remove this second,
redundant attaching of the phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of connected switches was sourced from the number of
children to the DSA node, change it to the number of available
children, skipping any disabled switches.
Fixes: 5e95329b70 ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering a mdio bus, Linux assumes than every port has a PHY and tries
to scan it. If a switch port has no PHY registered, DSA will fail to register
the slave MII bus. To fix this, set the slave MII bus PHY mask to the switch
PHYs mask.
As an example, if we use a Marvell MV88E6352 (which is a 7-port switch with no
registered PHYs for port 5 and port 6), with the following declared names:
static struct dsa_chip_data switch_cdata = {
[...]
.port_names[0] = "sw0",
.port_names[1] = "sw1",
.port_names[2] = "sw2",
.port_names[3] = "sw3",
.port_names[4] = "sw4",
.port_names[5] = "cpu",
};
DSA will fail to create the switch instance. With the PHY mask set for the
slave MII bus, only the PHY for ports 0-4 will be scanned and the instance will
be successfully created.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
In case we cannot attach to our slave netdevice PHY, error out and
propagate that error up to the caller: dsa_slave_create().
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case there is no PHY at the designated address on the internal
switch, we would basically de-reference a null pointer here:
dsa_slave_phy_setup(...)
{
p->phy = ds->slave_mii_bus->phy_map[p->port];
phy_connect_direct(slave_dev, p->phy, dsa_slave_adjust_link,
^------
This can be triggered when the platform configuration (platform_data or
Device Tree) indicates there should be a PHY device at this address, but
the HW is non-responsive, such that we cannot attach a PHY device at
this specific location.
Fix this by checking the return value prior to calling
phy_connect_direct().
CC: Andrew Lunn <andrew@lunn.ch>
Fixes: b31f65fb43 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neaten and standardize the logging output.
Other miscellanea:
o Use pr_notice_once instead of a guard flag.
o Convert existing pr_<level> uses too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ports phys are connected to the switches internal MDIO bus,
we need to connect the phy to the slave netdev, otherwise
auto-negotiation etc, does not work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading switch registers with 'ethtool -d'.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some chips it is possible to access the switch eeprom.
Add infrastructure support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches provide chip temperature data.
Add support for reporting it through the hwmon subsystem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting skb->protocol to a private protocol type may result in warning
messages such as
e1000e 0000:00:19.0 em1: checksum_partial proto=dada!
This happens if the L3 protocol is IP or IPv6 and skb->ip_summed is set
to CHECKSUM_PARTIAL. Looking through the code, it appears that changing
skb->protocol for transmitted packets is not necessary and may actually
be harmful. For example, it prevents purposely unmodified (from a DSA
perspective) network drivers from properly setting up their transmit
checksum offload pointers since they inspect skb->protocol to set up the
IPv4 header or IPv6 header pointers. So don't unnecessarily change the
protocol field.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a mismatch between enabled tagging protocols and the
protocol the switch supports, error out, rather than continue with a
situation which is unlikely to work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
cc: alexander.h.duyck@intel.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for the presence or not of the optional switch function
get_phy_flags() called the function, rather than checked to see if it
is a NULL pointer. This causes a derefernce of a NULL pointer on all
switch chips except the sf2, the only switch to implement this call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6819563e64 ("net: dsa: allow switch drivers to specify phy_device::dev_flags")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/dsa/slave.c uses functions and structures declared in phy_fixed.h
but does not explicitely include it, while dsa.h needs structure
declarations for 'struct ethtool_wolinfo' and 'struct ethtool_eee', fix
those by including the correct header files.
Fixes: ec9436baed ("net: dsa: allow drivers to do link adjustment")
Fixes: ce31b31c68 ("net: dsa: allow updating fixed PHY link information")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f7f1de51ed ("net: dsa: start and stop the PHY state machine")
add calls to phy_start() in dsa_slave_open() respectively phy_stop() in
dsa_slave_close().
We also call phy_start_aneg() in dsa_slave_create(), and this call is
messing up with the PHY state machine, since we basically start the
auto-negotiation, and later on restart it when calling phy_start().
phy_start() does not currently handle the PHY_FORCING or PHY_AN states
properly, but such a fix would be too invasive for this window.
Fixes: f7f1de51ed ("net: dsa: start and stop the PHY state machine")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch_suspend() and dsa_switch_resume() functions are only used
when PM_SLEEP is enabled, so they need #ifdef CONFIG_PM_SLEEP protection
to avoid a compiler warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switches driver to query and enable/disable EEE on a per-port
basis by implementing the ethtool_{get,set}_eee settings and delegating
these operations to the switch driver.
set_eee() will need to coordinate with the PHY driver to make sure that
EEE is enabled, the link-partner supports it and the auto-negotiation
result is satisfactory.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a per-port network device is used/unused, invoke the switch
driver port_enable/port_disable callbacks to allow saving as much power
as possible by disabling unused parts of the switch (RX/TX logic, memory
arrays, PHYs...). We supply a PHY device argument to make sure the
switch driver can act on the PHY device if needed (like putting/taking
the PHY out of deep low power mode).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_open() should start the PHY library state machine for its PHY
interface, and dsa_slave_close() should stop the PHY library state
machine accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switch drivers to implement per-port Wake-on-LAN getter and
setters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
