The return value of pci_enable_device() must be checked even in resume
callback:
sound/pci/ca0106/ca0106_main.c:1779: warning: ignoring return value of ‘pci_enable_device’, declared with attribute warn_unused_result
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the restoration of the standard PCI configuration registers
in the snd_hda_intel driver to a ->resume_early() callback executed
with interrupts disabled, since doing that with interrupts enabled
may lead to problems in some cases.
This patch addresses the regression from 2.6.26 tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12121 .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code overrides the event type on input pins always to
PWR_EVENT. Although this still works (PWR_EVENT and INSERT_EVENT
are handled samely), it'd be better to avoid such overrides.
Also, currently the unsol events are registered even for fixed pins
which will never raise the pin-detection event.
This patch fixes both issues.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pin-detection function used in patch_sigmatel.c shouldn't be specific
to HP pin because it's used for input pins in general, too.
This patch fixes the detection function, removes the HP check from it
and moves to stac92xx_hp_detect().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reduce the command timeout to 0.5sec. Should be enough to allow a
working command interface but removes a RCU stall and slow resume on
some revisions where the AC97 revision detection stalls in resume.
Signed-off-by: Peter Gruber <nokos@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the conversion (drop) from 24bit in the DSP to 16bit in AC97,
the maximum capture level on Audigy seems lower than it could be.
This patch adds a workaround to enable the artificial capture boost
switch. When this switch is on, the whole analog capature level is
boost up. However, this results in the lower capture resolution.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM9715 is software compatible with the WM9711 and WM9712.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- compatibility issue : change firmware filenames
the pcxhr driver version <= 1.0.18a does not work
with new firmware > 1.0.17. Keep the old firmware files
and add new firmware files with different names
Signed-off-by: Markus Bollinger <bollinger@digigram.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The power-state changes in patch_sigmatel.c are accessed via *_cached()
but they shouldn't be really cached. Fixed to the normal write.
Also, stac92hd71xx_suspend and resume are no longer necessary as the
power-state changes are handled properly in the common routine.
Removed these hacks now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amp switch of SPDIF outputs have to be cached in the amp cache
instead of codec cache. Otherwise it conflicts with the IEC958
playback switch control in hda_codec.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Gateway notebooks have their ID inside codec vendor ID, not at PCI ID. Due to
that, model auto-detection were not possible with the standard seek method.
This is what is found at lspci -vnn:
00:14.2 Audio device [0403]: ATI Technologies Inc SB450 HDA Audio [1002:437b] (rev 01)
Subsystem: ATI Technologies Inc SB450 HDA Audio [1002:437b]
Yet, autodetection is possible, since the codec properly reflects the vendor at
the Subsystem ID:
$ cat /proc/asound/card0/codec#0 |head -4
Codec: SigmaTel STAC9250
Address: 0
Vendor Id: 0x83847634
Subsystem Id: 0x107b0367
This patch adds a new autodetection function that seeks for codec subsystem ID.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The global functions in hda_codec.c and other core parts are only
for HD-audio codec and controller drivers. When the HD-audio driver
is built in kernel, all stuff have to be statically linked, thus
we don't need any exports.
This patch introduces a conditional macro to do export only
when needed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a hook for proc outputs of codec-specific stuff.
Moved realtek-specific coeff output into patch_realtek.c as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Moved power_save field initialization inside a proper ifdef
to fix a build error without CONFIG_SND_HDA_POWER_SAVE.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Split the monolithc HD-audio driver into several pieces:
- snd-hda-intel HD-audio PCI controller driver; loaded via udev
- snd-hda-codec HD-audio codec bus driver
- snd-hda-codec-* Specific HD-audio codec drivers
When built as modules, snd-hda-codec (that is invoked by snd-hda-intel)
looks up the codec vendor ID and loads the corresponding codec module
automatically via request_module().
When built in a kernel, each codec drivers are statically hooked up
before probing the PCI.
This patch adds appropriate EXPORT_SYMBOL_GPL()'s and the module
information for each driver, and driver-linking codes between
codec-bus and codec drivers.
TODO:
- Avoid EXPORT_SYMBOL*() when built-in kernel
- Restore __devinit appropriately depending on the condition
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function snd_mixart_create creates a link between mgr and card that
allows snd_mixart_free to free card as well. But if snd_mixart_create
fails, then the link has not been created and card has to be freed explicitly.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S,S1;
position p1,p2,p3;
expression E,E1;
type T,T1;
expression *ptr != NULL;
@@
(
if ((x@p1 = snd_card_new(...)) == NULL) S
|
x@p1 = snd_card_new(...);
)
... when != snd_card_free(...,(T)x,...)
when != if (...) { <+... snd_card_free(...,(T)x,...) ...+> }
when != true x == NULL || ...
when != x = E
when != E = (T)x
when any
(
if (x == NULL || ...) S1
|
if@p2 (...) {
... when != snd_card_free(...,(T1)x,...)
when != if (...) { <+... snd_card_free(...,(T1)x,...) ...+> }
when != x = E1
when != E1 = (T1)x
(
return \(0\|<+...x...+>\|ptr\);
|
return@p3 ...;
)
}
)
@ script:python @
p1 << r.p1;
p3 << r.p3;
@@
print "* file: %s snd_card_new: %s return: %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The reconfiguration of PCM affected all PCM streams on the bus, but
this this should be done rather only for the target codec.
This patch does the following:
- introduce bitmap indicating the PCM device usages on a hda_bus
- refactor the PCM build functions
- fix __devinit prefix in some fucntions
- add a proper ifdef around HDA-reconfig-specific functions
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move power_save option into hda_intel.c, and make a field in hda_bus,
instead of keeping module parameters in separate files.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Minor clean ups: move snd_hda_codecs_inuse() into hda_intel.c and
make static. Also, make snd_hda_query_supported_pcm() static
as it's used only in hda_codec.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no argument named @state in snd_hda_resume,
remove its' comment.
Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the model type instead of PCI SSID for detection of the mic types
on Dell laptops with IDT 92HD73xx codecs. In this way, a new laptop
can be tested via model module option.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed the quirk string for Dell studio 1535 (the product name wasn't
published at the time the patch was made).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC/IDT driver creates "Headphone as Line-Out" switch even if there
is no line-out pins on the machine. For devices only with headpohnes
and speaker-outs, this switch shouldn't be created.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- add support for pcxhr stereo cards mixer controls
- adjust tlv db scales to real dBu values
- fix bug with monitoring volume control pcxhr_monitor_vol_put
- do some cleanup
Signed-off-by: Markus Bollinger <bollinger@digigram.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Add support for pcxhr stereo cards and their firmware
- autorize sound cards without analog IO
- do some cleanup
Signed-off-by: Markus Bollinger <bollinger@digigram.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Add support for pcxhr stereo cards
- minor bugfixes : period and buffer size consraints
- fix PLL register values
- do some clean up
Signed-off-by: Markus Bollinger <bollinger@digigram.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Add support for pcxhr stereo cards
- do some clean up
Signed-off-by: Markus Bollinger <bollinger@digigram.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we need to handle many unsolicited events assigned to different
widgets, allocate the event dynamically using the existing events
array, and use the tag appropriately instead of combination of fixed
number and widget nid. (Note that widget nid can be over 4 bits!)
Also, replaced the call of unsol_event handler with a dedicated
function to be more readable.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AFG pin power-mapping isn't properly set for the fixed I/O pins
on IDT 92HD* codecs. This resulted in the low power mode after the
boot until any jack detection is executed, thus no output from the
speaker.
This patch fixes the power mapping for the fixed pins, and also fixes
the GPIO bits and digital I/O pin settings properly in stac92xx_ini().
Reference: Novell bnc#446025
https://bugzilla.novell.com/show_bug.cgi?id=446025
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SPDIF status bits controls are written via snd_hda_codec_write()
without caching. This causes a regression at resume that the bits
are lost.
Simply replacing it with the cached version fixes the problem.
Reference:
http://lkml.org/lkml/2008/11/24/324
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Medion MD96630 has ALC268 codec on slot#2 although it's not used
for any purpose. This codec conflicts with the primiary codec ALC888
on slot#0, and gives mixer errors.
This patch adds a corresponding entry to probe_mask blacklist.
Reference: Novell bnc#412528
https://bugzilla.novell.com/show_bug.cgi?id=412528
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes the bug 0004240: ALC888 - Intel HDA - Headphone Controlling.
It is made against the 2008-11-23 snapshot.
Added Realtek ALC888 model entry for the Fujitsu-Siemens Amilo Xa3530
laptop. It has 4 jacks: HP out, Mic-in, Line-in and Line-out/Side/SPDIF
(this one is on the laptop side, the other ones are on the rear).
Model detection works.
Headphone jack sense works now.
Front mic works now, was same as Acer Aspire 4930G.
Added channel mode from 2 to 8 channels.
In 2ch and 4ch modes, the front is also sent to the Line-out/side jack
for convenience instead of just muting the Line-out/side jack like other
models do.
When using the Mic-in jack as CLFE, the sound is very low (bug?). To
work it around, in 6ch mode the CLFE channel is duplicated to the
Line-out/side jack because this one has a better amp.
Cc: manu@frogged.de
Signed-off-by: Vincent Petry <PVince81@yahoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC/IDT driver creates "Headphone as Line-Out" switch even if there
is no line-out pins on the machine. For devices only with headpohnes
and speaker-outs, this switch shouldn't be created.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix "defined but not used" build warning by moving eld_versoin_names[]
and cea_edid_version_names[] into hdmi_print_eld_info().
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DisplayPort is a digital display interface standard put forth by
the Video Electronics Standards Association (VESA). It defines a
new license-free, royalty-free, digital audio/video interconnect,
intended to be used primarily between a computer and its display monitor,
or a computer and a home-theater system.
- From Wikipedia, the free encyclopedia
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- rename ELD proc write routine to hdmi_write_eld_info()
- support modifying WMAPro's profile
Write to some ELD fields (monitor_name, manufacture_id, product_id,
eld_version, edid_version) are deliberately not supported, since that
won't correct wrong behaviors and only leads to confusions.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- make some messages more user friendly
- add message prefix "HDMI:" to indicate the problem's domain
(also easier to do `dmesg | grep HDMI` ;-)
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Print some CA selecting info, which could be valuable for debugging when
something goes wrong.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_print_pcm_rates() and snd_print_pcm_bits() are used by both
hda_proc.c and hda_eld.c, thus they have to be defined in the common
place.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed the quirk string for Dell studio 1535 (the product name wasn't
published at the time the patch was made).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the following sparse warning:
sound/pci/hda/patch_nvhdmi.c:161:25: warning: symbol
'snd_hda_preset_nvhdmi' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the codec re-configuration feature selectable via Kconfig,
CONFIG_SND_HDA_RECONFIG.
Also mark it as experimental (as it really is).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The jack instances created in patch_sigmatel.c may be double-freed.
The device management code checks the invalid element, and thus there
is no real breakage, but it spews annoying warning messages.
But, we can't simply remove the release calls of these jack instances
because they have to be freed when the codec is re-configured.
Now, a new flag, bus->shutdown is introduced to indicate that the bus
is really being unloaded, i.e. the objects managed by the device
manager will be automatically deleted. We release these objects only
when this flag isn't set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow users to fix quicks of ELD ROMs by writing new values to the ELD proc
interface. The format is one or more lines of "name hex_value".
Users can add/remove/modify up to 32 SAD(Short Audio Descriptor) entries.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename "monitor name" to "monitor_name" to conform with the keyword style.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added STAC_DELL_M4_3 quirk for Dell systems, also reorganized the
board config switch to assign number of digital muxes, microphones,
and SPDIF muxes via the PCI quirk defined.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The changes specific for Samsung laptops seem unapplicable to other
hardware models like ASUS. The mic inputs are lost on such hardware
by the change 5d5d5f43f1.
This patch adds back the old laptop-eapd model, and create a new
model "samsung" for the new one specific to Samsung laptops with
automatic mic selection feature.
Reference: kernel bugzilla #12070http://bugzilla.kernel.org/show_bug.cgi?id=12070
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for EAPD on system suspend and disabling EAPD on headphone jack
detection for STAC_DELL_M6 laptops.
This patch fixes the regressions, the silent output on HP of some Dell
laptops (see Novell bnc#446025):
https://bugzilla.novell.com/show_bug.cgi?id=446025
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added Realtek ALC888 model entry for the Acer Aspire 4930G laptop that
fixes the following features:
- internal microphone
- heaphone jack sense
- channel mode
Signed-off-by: Vincent Petry <PVince81@yahoo.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace 5 free-and-return-err blocks with goto-out-free ones.
This makes the main logic more outstanding.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Strip out some ELD printk messages that end user won't care,
and make the output compact.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a global function snd_print_pcm_bits() and use it in the ELD code.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Moved support for EAPD mute on suspend from stac92hd71xx_suspend
to the generic stac92xx_suspend function.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Refactor the channel mapping code for consistent naming
and make it more informed about channel allocations.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To play a 3+ channels LPCM/DSD stream via HDMI,
- HDMI sink must tell HDMI source about its speaker placements
(via ELD, speaker-allocation field)
- HDMI source must tell the HDMI sink about channel allocation
(via audio infoframe, channel-allocation field)
(related docs: HDMI 1.3a spec section 7.4, CEA-861-D section 7.5.3 and 6.6)
This patch attempts to set the CA(channel-allocation) byte in the audio infoframe
according to
- the number of channels in the current stream
- the speakers attached to the HDMI sink
A channel_allocations[] line must meet the following two criteria to be
considered as a valid candidate for CA:
1) its number of allocated channels = substream->runtime->channels
2) its speakers are a subset of the available ones on the sink side
If there are multiple candidates, the first one is selected. This simple
policy shall cheat the sink into playing music, but may direct data to the
wrong speakers.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
code refactor: make a global function snd_print_channel_allocation().
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
code refactor: make a standalone function hdmi_fill_audio_infoframe().
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the multiple imux instances for matrix-type mixers like ALC882.
So far, only ALC260 used this feature, but other codecs may need a
similar stuff.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed the GPIO mask and co initialization in patch_stac92hd71bxx()
so that the gpio_maks for HP_M4 model is set properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed the restore of pin configs at resume for some STAC/IDT codec
models. These models set explicitly the pin configs after the default
init configs, and these aren't restored properly at resume.
This patch introduces two changes:
- Allocate always pin_configs array in stac_spec so that the driver
can overwrite the value freely
- Introduce stac_change_pin_config() to change the pin config value
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call the init callback and remove duplicated codes in stac92xx_resume().
This also fixes the missing initialization such as digital I/O pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The jack detection input elements should be created in build_controls
callback instead of init callback because init can be called multiple
times by suspend/resume and power-saving.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create /proc/asound/card<card_no>/eld#<codec_no> to reflect the audio
configurations and capabilities of the attached HDMI sink.
Some notes:
- Shall we show an empty file if the ELD content is not valid?
Well it's not that simple. There could be partially populated ELD,
and there may be malformed ELD provided by buggy drivers/monitors.
So expose ELD as it is.
- The ELD retrieval routines rely on the Intel HDA interface,
others are/could be universal and independent ones.
- How do we name the proc file?
If there are going to be two HDMI pins per codec, then the current naming
scheme (eld#<codec no>) will fail. Luckily the user space dependencies should
be minimal, so it would be trivial to do the rename if that happens.
- The ELD proc file content is designed to be easy for scripts and human reading.
Its lines all have the pattern:
<item_name>\t[\t]*<item_value>
where <item_name> is a keyword in c language, while <item_value> could be any
contents, including white spaces. <item_value> could also be a null value.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ELD handling routines can be shared by all HDMI codecs,
and they are large enough to make a standalone source file.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We want to share some code with print_pcm_rates(),
so extract a common routine snd_print_pcm_rates() from it.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove get_amp_nid(): it duplicates the one defined in hda_local.h
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reorder HDMI audio enabling sequence so that
1) the sink knows about the coming audio stream
2) unmute
3) start transferring audio samples
The theory is that in the path A=>B=>C, we first make C ready, and then
enable B, and lastly allow A to send audio samples.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for EAPD on system suspend and disabling EAPD on headphone jack
detection for STAC_DELL_M6 laptops.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new alc883 model ALC1200_ASUS_P5Q for ASUS P5Q-EM boards.
It is the same as ALC883_6ST_DIG except that the SPDIF digital
output nid is 0x10.
Tested-by: Andrei Tanas <andrei@tanas.ca>
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check board preset model instead of codec->subsystem_id in
patch_92hd71bxx() so that other hardwares configured via the model
option work like the given model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Error handling code following a kzalloc should free the allocated data.
The error handling code is adjusted to call pci_disable_device(pci); as
well, as done later in the function
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Changed value for STAC_VREF_EVENT from 0x40 to 0x00 because the
unsol response value is only 6-bits width and the former value
was 1<<6 which is an overrun.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Split the bound Master control to individual Headphone and Speaker
volume controls for VAIO with STAC982x codecs.
The Master controls is still created as a vmaster.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The digital beep widget may have no mute control, and always enabling
the beep is ofen pretty annoying, especially on laptops.
This patch adds a mixer control "PC Beep Playback Switch" when there
is no mixer amp mute is found, and controls it on software.
Reference: Novell bnc#444572
https://bugzilla.novell.com/show_bug.cgi?id=444572
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch uses HD Audio PCI class code to detect AMD HD Audio cards.
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the handling of SiI1392 HDMI codec from patch_atihdmi.c to
patch_intelhdmi.c, which makes our ASUS P5E-VM HDMI board work.
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The card->id (card text identification) can be changed at runtime.
It might be confusing to have old text identification in device name.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the recent change for multiple HP as line-out switch, only
one of the multiple headphons (usually a wrong one) is toggled
and the other pins are still disabled. This causes the silent output
problem on some Dell laptops.
Also, the hp_switch check is screwed up when a line-in or a mic-in
jack exists. This is added as an additional output, but hp_switch
check doesn't take it into account.
This patch fixes these issues: simplify hp_switch check by using
the NID instead of bool, and clean up / fix the toggle of HP pins
in unsol event handler code.
Reference: Novell bnc#443267
https://bugzilla.novell.com/show_bug.cgi?id=443267
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The input pins are sometimes not initialized properly because
of the optimization check of the current pinctl code.
Force to initialize the mic input pins so that they can be set up
properly even if they were in a weird state. But keep other input
pins if already set up as input, since this could be an extra mic
pin.
Reference: Novell bnc#443738
https://bugzilla.novell.com/show_bug.cgi?id=443738
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The creation of analog-mux mixer element is missing in
patch_stac9200() due to the dynamic allocation patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a QUIRK to patch_analog.c for the HP Elitebook 8530p
(IDs 0x103c:0x30e7) to use AD1884A model 'laptop' by default.
Playback and Capture confirmed working.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
currently, the error message when trying to run hdspmixer or hdspconf
if the breakout box is not connected is somehow misleading, since it
asks the user to upload the firmware.
this patch adds a test, whether the breakout box is connected and
tries to upload the firmware in the case, that it is not present, e.g.
because of power failures of the breakout box.
[Minor coding-style fixes by tiwai]
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
currently the hdsp driver tries to upload the firmware, even if the
io box is not connected. this patch adds a check for the io box
before trying to upload the firmware.
thus instead of messages complaining about the fifo status and firmware
loading failure, the driver gives a message that no multiface or
digiface is connected.
[A minor coding-style fix by tiwai]
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added model=laptop for another HP machine (103c:3614) with AD1884A
codec.
Signed-off-by: Michel Marti <mma@objectxp.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on Dell Studio Desktop tells wrong codec probe masks.
This patch gives the preset mask value to avoid invalid access.
Reference: Novell bug#440907
https://bugzilla.novell.com/show_bug.cgi?id=440907
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The master switch doesn't influence on NID 0x15, the headphone jack
on HP 3013 model because alc260_hp_master_update() ignores the passed
arguments.
Also, corrected the wrong arguments of hp3013 (0x10 and 0x15) although
this doesn't change any behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The widget layout of the Fujitsu Lifebook S6420 (which is ICH9M-based
and uses an ALC269) is similar but not identical to the Lifebook
S6410/E8410 (which are ICH8M-based and use an ALC262).
It is named lifebook as fujitsu is in use for Amilo machines. This builds
on the Quanta FL1 work and supports all analog inputs & outputs that I am
aware of. Microphone autoswitch is implemented. The laptop mic port takes
precedence over the dock mic port if both happen to have a jack plugged in.
This made sense to me as a design decision (imagine a presentation
environment with the dock fully wired in and the presenter quickly wanting
to override the mic with a headset).
There is mention of a digital audio path on the codec graph, so perhaps
the headphone socket is dual-function analog/digital. I will follow up
with another patch if I can acquire equipment to test this.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an error occurs during the codec probing, typically accessing to an
non-existing codec slot, the controller chip gets often screwed up and
can no longer communicate with the codecs.
This patch adds a preparation phase just to probe codec addresses before
actually creating codec instances. If any error occurs during this
probing phase, the driver resets the controller to recover.
This will (hopefully) fix the famous "single_cmd" errors.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hda_bus ops callback take struct hda_bus pointer.
Also, the command callback takes the composed command word, instead of
each small bits in arguments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are actually two variants of ALC268 Acer implementation, one
with an analog built-in mic (pin 0x19) and another with a digital
mic (pin 0x12). Created a new model, acer-dmic, for the latter case
now.
So far, all known models are assigned to be analog-mic, according to
the BIOS setup. If this doesn't match with the actual case, one needs
to try model=acer-dmic, and fix the entry to point ALC268_ACER_DMIC
if it works.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Asus V1s series laptops have an ALC660VD with PCI id: 0x1043, 0x1633.
1.) remove the previous behaviour of mapping that to the ALC861VD_LENOVO
device.
2.) add a new ALC660VD_V1S device based on ALC861VD_LENOVO, with an
added digital out.
Signed-off-by: Tristan Aston <astrotris@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a proper ifdef to shut out a compile warning:
CC [M] sound/pci/hda/patch_intelhdmi.o
sound/pci/hda/patch_intelhdmi.c:286: warning: ‘hdmi_get_dip_index’ defined but \
not used
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the hda-reconfiguration patches, the check of empty stream
is gone, and this results in an error with the codec setup with empty
streams.
This patch adds the check again to avoid the error at probing.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add NULL-check of the return value of snd_kctl_new1() before
accessing it. Also, make a sanity NULL check to snd_BUG_ON()
for debugging only.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for explicitly enabling the EQ distortion hack for
systems without software biquad support.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a quirk for another Acer Aspier laptop (1025:0090) with ALC883
codec. Reported in Novell bnc#426935:
https://bugzilla.novell.com/show_bug.cgi?id=426935
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The IRQMASK register has to be set to zero expclitily at the initialization
otherwise you'll get no interrupts properly at later operations.
Also, removed the old commented out codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unified the capture mixer creation in patch_realtek.c.
ALC268 is still an exception since it has no AMP in ADC but in
MUX widget.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unify the capture callbacks in patch_realtek.c.
The difference of matrix or mux style is checked via spec->is_mix_capture
flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The digital mic wasn't detected properly for ALC269 auto-probing mode
because of its widget number. Fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent addition of automatic mic-muting is broken in some cases.
The code assumes that the pin nids <= 0x18, but the digital pins can
be less than 0x18.
Also, it assumes the front-mic being the internal mic, but it depends
on the hardware implementation actually.
Instead of complex case-fixes, better to disable the code as now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Neither has any significance currently to the flow
because err is checked for the same condition before
the place of disagreement.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current snd-hda-intel driver seems blocking the power-off on some
devices like eeepc. Although this is likely a BIOS problem, we can add
a workaround by disabling IRQ lines before power-off operation.
This patch adds the reboot notifier to achieve it.
The detailed problem description is found in bug#11889:
http://bugme.linux-foundation.org/show_bug.cgi?id=11889
Tested-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SPDIF mute switch code seems broken. It doesn't set unmute bits
properly. Also it contains the duplicated lines (merge error?) to be
cleaned up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add Wolfson Microelectronics to the HDA vendor ID table.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removed the old workaround to avoid the non-existing codec slot.
The current code should work without that workaround. If any,
we can add a quirk table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some machines have broken BIOS resume that doesn't restore the default
pin configuration properly, which results in a wrong detection of HP
pin. This causes a silent speaker output due to missing HP detection.
Related bug: Novell bug#406101
https://bugzilla.novell.com/show_bug.cgi?id=406101
This patch fixes the issue by saving/restoring the default pin configs
by the driver itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support to the IDT codec families to report jack status
to the jack abstraction layer. This required some reorganization in the
stac92xx_unsol_event function in which the index value is changed to
reporting the nid with the event.
Also adds an sigmatel_jack struct to keep track of the nid relation
to the jack abstraction layer instance. Also adds functions to set and
retrieve data values for each nid, this is used in stac92xx_unsol_event
to retrieve the GPIO mask for STAC_VREF_EVENT.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds snd_hda_get_jack* functions for reporting jack location,
device, and connectivity type.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I fixed all of coding style errors and some warnings, now it is down to:
checkpatch.pl-0.24 --no-tree --file --strict --terse emu10k1_main.c
total: 0 errors, 62 warnings, 7 checks, 2075 lines checked
Signed-off-by: Vedran Miletic <rivanvx@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 18c7109289 had #endif leftoff from
compilation. This patch fixes it.
Also, I replaced a misplaced comment by a useful one, that explains why are
here #ifdef and #endif added in compilation.
Signed-off-by: Vedran Miletic <rivanvx@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* added missing SBxxxx, CTxxxx, PCxxx and MAEMxxxx where they were missing,
and fixed some of them which were wrong (according to kx.inf, which is pretty
accurate compared to anything out there)
* fixed device names to make them more consistent across various cards
* fixed order of devices where appropriate
Signed-off-by: Vedran Miletic <rivanvx@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC260 auto-parsing mode may create multiple controls for the same volume
widget (0x08 and 0x09) depending on the pin. For example, Front and
Headphone volumes may control the same volume, just the latter one wins.
This patch adds a proper check of the existing of the volume control
and avoid the doulbed creation of the same volume controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the newly introduced pci_ioremap_bar() function in sound/.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some hardwares with ALC655 codec don't indicate the proper ext id bit
for SPDIF output although it supports. Force to enable the bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The jack instance has to be release manually in free callback
in patch_sigmatel.c for dynamic reconfiguration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added support for jack detection reporting to userspace for
IDT/Sigmatel codecs.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
