Commit 5143c953a7 ("mmc: sdhci-esdhc-imx: Allow all supported
prescaler values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR
mode, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value if the i.MX53
eSDHCv3 is detected. According to the i.MX53 reference manual, if
DLLCTRL[10] can be set, then the controller is eSDHCv3, else it is
eSDHCv2.
This commit fixes the following issue, which was preventing the i.MX53
Loco (IMX53QSB) board from booting Linux 4.15.0-rc5:
[ 1.882668] mmcblk1: error -84 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc00
[ 2.002255] mmcblk1: error -84 transferring data, sector 2050, nr 6, cmd response 0x900, card status 0xc00
[ 12.645056] mmc1: Timeout waiting for hardware interrupt.
[ 12.650473] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 12.656921] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001201
[ 12.663366] mmc1: sdhci: Blk size: 0x00000004 | Blk cnt: 0x00000000
[ 12.669813] mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
[ 12.676258] mmc1: sdhci: Present: 0x01f8028f | Host ctl: 0x00000013
[ 12.682703] mmc1: sdhci: Power: 0x00000002 | Blk gap: 0x00000000
[ 12.689148] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000003f
[ 12.695594] mmc1: sdhci: Timeout: 0x0000008e | Int stat: 0x00000000
[ 12.702039] mmc1: sdhci: Int enab: 0x107f004b | Sig enab: 0x107f004b
[ 12.708485] mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00001201
[ 12.714930] mmc1: sdhci: Caps: 0x07eb0000 | Caps_1: 0x08100810
[ 12.721375] mmc1: sdhci: Cmd: 0x0000163a | Max curr: 0x00000000
[ 12.727821] mmc1: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x00000000
[ 12.734265] mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 12.740709] mmc1: sdhci: Host ctl2: 0x00000000
[ 12.745157] mmc1: sdhci: ADMA Err: 0x00000001 | ADMA Ptr: 0xc8049200
[ 12.751601] mmc1: sdhci: ============================================
[ 12.758110] print_req_error: I/O error, dev mmcblk1, sector 2050
[ 12.764135] Buffer I/O error on dev mmcblk1p1, logical block 0, lost sync page write
[ 12.775163] EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
[ 12.782746] VFS: Mounted root (ext4 filesystem) on device 179:9.
[ 12.789151] mmcblk1: response CRC error sending SET_BLOCK_COUNT command, card status 0x900
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: Wladimir J. van der Laan <laanwj@gmail.com>
Tested-by: Wladimir J. van der Laan <laanwj@gmail.com>
Fixes: 5143c953a7 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The global array clashes with a newly added symbol of the same name:
drivers/staging/ccree/cc_debugfs.o:(.data+0x0): multiple definition of `debug_regs'
drivers/mmc/host/s3cmci.o:(.data+0x70): first defined here
We should fix both, this one addresses the s3cmci driver by removing
the symbol from the global namespace. While at it, this separates
the declaration from the type definition and makes the variable const.
Fixes: 9bdd203b4d ("s3cmci: add debugfs support for examining driver and hardware state")
Fixes: b3ec9a6736 ("staging: ccree: staging: ccree: replace sysfs by debugfs interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following error occurs when loading renesas_sdhi_core.c module,
so add MODULE_LICENSE("GPL v2").
renesas_sdhi_core: module license 'unspecified' taints kernel.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Fixes: 9d08428afb ("mmc: renesas-sdhi: make renesas_sdhi_sys_dmac main module file")
Cc: <stable@vger.kernel.org> # v4.13+
[Shimoda: Added Fixes tag and Cc to the stable ML]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit de3ee99b09 ("mmc: Delete bounce buffer handling") deletes the
bounce buffer handling, but also causes the max_req_size for sdhci to be
increased, in case when max_segs == 1. This causes errors for sdhci-pci
Ricoh variant, about the swiotlb buffer to become full.
Fix the issue, by taking IO_TLB_SEGSIZE and IO_TLB_SHIFT into account when
deciding the max_req_size for sdhci.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Fixes: de3ee99b09 ("mmc: Delete bounce buffer handling")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Not all instances of the SDCC core supports changing signal voltage and
as such will not generate a power interrupt when the software attempts
to change the voltage. This results in probing the eMMC on some devices
to take over 2 minutes.
Check that the SWITCHABLE_SIGNALING_VOLTAGE bit in MCI_GENERICS is set
before waiting for the power interrupt.
Cc: Sahitya Tummala <stummala@codeaurora.org>
Cc: Vijay Viswanath <vviswana@codeaurora.org>
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3Gvx
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups"
* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
mmc: dw_mmc: Convert timers to use timer_setup()
mmc: dw_mmc: Cleanup the DTO timer like the CTO one
mmc: vub300: Use common code in __download_offload_pseudocode()
mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
mmc: Convert timers to use timer_setup()
mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
mmc: sdhci-acpi: Let devices define their own private data
mmc: mediatek: perfer to use rise edge latching for cmd line
mmc: mediatek: improve eMMC hs400 mode read performance
mmc: mediatek: add latch-ck support
mmc: mediatek: add support of source_cg clock
mmc: mediatek: add stop_clk fix and enhance_rx support
mmc: mediatek: add busy_check support
mmc: mediatek: add async fifo and data tune support
mmc: mediatek: add pad_tune0 support
mmc: mediatek: make hs400_tune_response only for mt8173
arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
...
The Socionext SynQuacer SoC inherits this IP from Fujitsu, but
requires the F_SDH30_CMD_DAT_DELAY bit to be set in the
F_SDH30_ESD_CONTROL control register. So set this bit if the
DT node has the 'fujitsu,cmd-dat-delay-select' property.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As documented in Documentation/timers/timers-howto.txt
as follows, replace msleep() with usleep_range().
msleep(1~20) may not do what the caller intends, and
will often sleep longer (~20 ms actual sleep for any
value given in the 1~20ms range). In many cases this
is not the desired behavior.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The recent CTO timer introduced in commit 03de19212e ("mmc: dw_mmc:
introduce timer for broken command transfer over scheme") was causing
observable problems due to race conditions. Previous patches have
fixed those race conditions.
It can be observed that these same race conditions ought to be
theoretically possible with the DTO timer too though they are
massively less likely to happen because the data timeout is always set
to 0xffffff right now. That means even at a 200 MHz card clock we
were arming the DTO timer for 94 ms:
>>> (0xffffff * 1000. / 200000000) + 10
93.886075
We always also were setting the DTO timer _after_ starting the
transfer, unlike how the old code was seting the CTO timer.
In any case, even though the DTO timer is much less likely to have
races, it still makes sense to add code to handle it _just in case_.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a jump target so that a specific string copy operation is stored
only once at the end of this function implementation.
Replace two calls of the function "strncpy" by goto statements.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Add a jump target so that a bit of exception handling can be better
reused at the end of this function.
* Adjust condition checks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Tony Olech <tony.olech@elandigitalsystems.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Allen <allen.lkml@gmail.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some Intel host controllers use an ACPI device-specific method to ensure
correct voltage switching. Fix voltage switch for those, by adding a call
to the DSM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let devices define their own private data to facilitate device-specific
operations. The size of the private structure is specified in the
sdhci_acpi_slot structure, then sdhci_acpi_probe() will allocate extra
space for it, and sdhci_acpi_priv() can be used to get a reference to it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
data lines have applied to perfer to use rise edge, also need
apply it to cmd line.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
enlarge outstanding value to improve read performance
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
some platform(eg.mt2701) does not support "stop clk fix", in
this case, need set correct latch-ck to avoid crc error caused
by stop clock block-internally.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
source clock need an independent cg to control, when doing clk mode
switch, need gate source clock to avoid hw issue(multi-bit sync hw hang)
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2712 supports stop_clk fix and enhance_rx, which can improve
host stability.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
bit7 of PATCH_BIT1 has different meaning in new design, to
compatible with previous platform, clear this bit in new
platform.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2701/mt2712 supports async fifo & data tune, which can improve
host stability.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
from mt2701, the register of PAD_TUNE has been phased out,
while there is a new register of PAD_TUNE0
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the origin design of hs400_tune_response is for mt8173 because of
mt8173 has a special design. for doing that, we add a new member
"compatible", by now it's only for mt8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like the CTO timeout calculation introduced recently, the DTO
timeout calculation was incorrect. It used "bus_hz" but, as far as I
can tell, it's supposed to use the card clock. Let's account for the
div value, which is documented as 2x the value stored in the register,
or 1 if the register is 0.
NOTE: This was likely not terribly important until commit 16a34574c6
("mmc: dw_mmc: remove the quirks flags") landed because "DIV" is
documented on Rockchip SoCs (the ones that used to define the quirk)
to always be 0 or 1. ...and, in fact, it's documented to only be 1
with EMMC in 8-bit DDR52 mode. Thus before the quirk was applied to
everyone it was mostly OK to ignore the DIV value.
I haven't personally observed any problems that are fixed by this
patch but I also haven't tested this anywhere with a DIV other an 0.
AKA: this problem was found simply by code inspection and I have no
failing test cases that are fixed by it. Presumably this could fix
real bugs for someone out there, though.
Fixes: 16a34574c6 ("mmc: dw_mmc: remove the quirks flags")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This attempts to instill a bit of paranoia to the code dealing with
the CTO timer. It's believed that this will make the CTO timer more
robust in the case that we're having very long interrupt latencies.
Note that I originally thought that perhaps this patch was being
overly paranoid and wasn't really needed, but then while I was running
mmc_test on an rk3399 board I saw one instance of the message:
dwmmc_rockchip fe320000.dwmmc: Unexpected interrupt latency
I had debug prints in the CTO timer code and I found that it was
running CMD 13 at the time.
...so even though this patch seems like it might be overly paranoid,
maybe it really isn't?
Presumably the bad interrupt latency experienced was due to the fact
that I had serial console enabled as serial console is typically where
I place blame when I see absurdly large interrupt latencies. In this
particular case there was an (unrelated) printout to the serial
console just before I saw the "Unexpected interrupt latency" printout.
...and actually, I managed to even reproduce the problems by running
"iw mlan0 scan > /dev/null" while mmc_test was running. That not only
does a bunch of PCIe traffic but it also (on my system) outputs some
SELinux log spam.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the commit 03de19212e ("mmc: dw_mmc: introduce timer for broken
command transfer over scheme") we tried to calculate the expected
hardware command timeout value. Unfortunately that calculation isn't
quite correct in all cases. It used "bus_hz" but, as far as I can
tell, it's supposed to use the card clock. Let's account for the div
value, which is documented as 2x the value stored in the register, or
1 if the register is 0.
NOTE: It's not expected that this will actually fix anything important
since the 10 ms margin added by the function will pretty much dwarf
any calculations. The card clock should be 100 kHz at minimum and:
1000 ms/s * (255 * 2) / 100000 Hz.
Gives us 5.1 ms.
...so really the point of this patch is just to make the code more
"correct" in case anyone ever tries to remove the 10 ms buffer.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When running with the commit 03de19212e ("mmc: dw_mmc: introduce
timer for broken command transfer over scheme") I found this message
in the log:
Unexpected command timeout, state 7
It turns out that we weren't properly cancelling the new CTO timer in
the case that a voltage switch was done. Let's promote the cancel
into the dw_mci_cmd_interrupt() function to fix this.
Fixes: 03de19212e ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2701/mt2712 has 12bit clock div, which is not compatible with
mt8135/mt8173. and, some additional features will be added in
mt2701/mt2712, so that need distinguish it by comatibale name.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We keep PCI Ids in sdhci-pci.h and the O2-specific definitions belong in
sdhci-pci-o2micro.c. Move those definitions accordingly. Remove unused O2
definitions in sdhci-pci-core.c. The 3 o2micro external function
declarations might as well be in sdhci-pci.h as well, so move them there
and get rid of sdhci-pci-o2micro.h entirely.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tidy Intel slot probe functions into one. A single function can be used
because the logic uses hid / uid as necessary to identify devices anyway.
This gets rid of some pointless comments and checks for variables that
cannot possibly be NULL, as well as giving the function a name that
identifies it as specific to Intel controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of acpi_device_uid() instead of open coding.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement fallback compatibility strings for R-Car Gen 1, 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Also, improve readability by listing the shmobile fallback compatibility
string after the more-specific compatibility strings they provide a
fallback for.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Accessing register fields generally need mask and shift part.
Defining them separately, like SDHCI_CDNS_HRS06_TUNE_{SHIFT,MASK},
is tedious.
Register fields can be always defined by GENMASK (or, BIT if it it
a single bit). They are nicely handled by FIELD_* macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using PTR_ERR_OR_ZERO() instead of IS_ERR() works, but it's not how
you're supposed to write these conditions.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This has a copy and paste bug so we use "host->fixed_factor_clk" which
is a valid pointer instead of "host->cfg_div_clk" which holds the error
code.
Fixes: ed80a13bb4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoCs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
