Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The compatible string for the LCD panel used for the Q8 tablets are just
a placeholder that was shown to be compatible with the actual panels
found on these devices. The real panels do not have any identifiable
markings and vary between production runs.
The compatibe string previously used had a pixel clock that could not
be accurately reproduced on Allwinner hardware, and discussions on
whether a margin should be added to the display drivers and how large
a margin was acceptable had stalled.
Now that we have a panel model that is actually used with Allwinner
hardware, has the same dimensions, and the timings have been shown to
work with the nameless panels, we can use that one instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A13 Q8 tablet, following the A13 reference tablet design, has the
system's fixed 3.3V rail feed the VCC supply of the LCD panel.
Additional voltage rails used by the panel are generated using a
regulator fed from the unregulated IPSOUT output of the PMIC. The latter
is unrepresentable in the device tree. Both are controlled with MOSFETs
by the enable GPIO added in the previous patch. The actual enable or
reset pin for the panel is tied directly to LCD-VCC after the MOSFET.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the AXP209 GPIOs, we can toggle the LCD panel enable
line. Add the GPIO phandle to the panel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The panel backlight and enable GPIO comments were incorrectly placed
in the input port, while it should have been in the panel node itself.
Move them to the correct position.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Rename sun5i-q8-common.dtsi to sun5i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a preparation patch for renaming sun5i-q8-common.dtsi to
sun5i-reference-design-tablet.dtsi and sharing it between all
the A13 tablet dts files.
Since we only have a panel config for the 18 tablets (for now) move
this to the q8 specific dts file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The early A13 Q8 tablets all use a Realtek WiFi module connected to
USB1. The module is powered by AXP209's LDO3 at 3.3V.
Move the related settings from sun5i-a13-q8-tablet.dts to
sun5i-q8-common.dtsi, for all q8-based tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commits adds a generic dts file for q8 formfactor a13 based tablets.
The tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
The touchscreen controller / accelerometer may turn out to be a problem
once we add support for those. We can either do something with devicetree
overlays, or add sun5i-a13-<touchscreen>-<accelerometer>.dts files. The
latter is what the android mod community is doing with firmware images.
This dts was tested with an a13 q8 tablet with a pcb labelled: "94V-0",
silead gsl1680 touchscreen controller and a mc32x0 accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
