When CONFIG_ATH11K_DEBUGFS is disabled, but CONFIG_MAC80211_DEBUGFS
is turned on, the driver fails to build:
drivers/net/wireless/ath/ath11k/debugfs_sta.c: In function 'ath11k_dbg_sta_open_htt_peer_stats':
drivers/net/wireless/ath/ath11k/debugfs_sta.c:416:4: error: 'struct ath11k' has no member named 'debug'
ar->debug.htt_stats.stats_req = stats_req;
^~
It appears that just using the former symbol is sufficient here,
adding a Kconfig dependency takes care of the corner cases.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some targets ex: QCS404, SCM permissions for MSA region is
statically configured in TrustZone fw. Add SCM call disable option
for such targets to avoid duplicate permissions.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 76d164f582.
PCIe hung issue was observed on multiple platforms. The issue was reproduced
when DUT was configured as AP and associated with 50+ STAs.
For QCA9984/QCA9888, the DMA_BURST_SIZE register controls the AXI burst size
of the RD/WR access to the HOST MEM.
0 - No split , RAW read/write transfer size from MAC is put out on bus
as burst length
1 - Split at 256 byte boundary
2,3 - Reserved
With PCIe protocol analyzer, we can see DMA Read crossing 4KB boundary when
issue happened. It broke PCIe spec and caused PCIe stuck. So revert
the default value from 0 to 1.
Tested: IPQ8064 + QCA9984 with firmware 10.4-3.10-00047
QCS404 + QCA9984 with firmware 10.4-3.9.0.2--00044
Synaptics AS370 + QCA9888 with firmware 10.4-3.9.0.2--00040
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When simulate random transfer fail for sdio write and read, it crash
sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. it crash, the act len of ath10k_htc_hdr is higher than allocate len, it cause panic:
[ 99.723482] skbuff: skb_over_panic: text:00000000caa0f780 len:57013 put:57013 head:000000004116f24a data:0000000019ecb4dc tail:0xdef5 end:0x640 dev:<NULL>
[ 99.737697] ------------[ cut here ]------------
[ 99.742327] kernel BUG at /mnt/host/source/src/third_party/kernel/v4.19/net/core/skbuff.c:104!
[ 99.750937] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 99.831154] Process kworker/0:2 (pid: 151, stack limit = 0x00000000728010bf)
[ 99.838200] CPU: 0 PID: 151 Comm: kworker/0:2 Tainted: G W 4.19.85 #48
[ 99.846022] Hardware name: MediaTek krane sku0 board (DT)
[ 99.851429] Workqueue: events sdio_irq_work
[ 99.855614] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 99.860402] pc : skb_panic+0x64/0x68
[ 99.863974] lr : skb_panic+0x64/0x68
[ 99.867542] sp : ffffff8008833a90
[ 99.870850] x29: ffffff8008833ac0 x28: ffffffe52e337370
[ 99.876159] x27: ffffffe52e328a90 x26: 000000000000e0d0
[ 99.881469] x25: ffffffe52e336b60 x24: 000000000000deb5
[ 99.886779] x23: ffffffe52e340680 x22: ffffffe4efd47e00
[ 99.892088] x21: 000000000000deb5 x20: ffffffa516d85b4c
[ 99.897397] x19: ffffffa526928037 x18: 0000000000000000
[ 99.902706] x17: 000000000000003c x16: ffffffa5265b6c80
[ 99.908015] x15: 0000000000000006 x14: 3a76656420303436
[ 99.913325] x13: 0000000000029bf0 x12: 0000000000000000
[ 99.918634] x11: 0000000000000000 x10: 0000000000000000
[ 99.923943] x9 : a3b907e4b2783000 x8 : a3b907e4b2783000
[ 99.929253] x7 : 0000000000000000 x6 : ffffffa526f66d76
[ 99.934563] x5 : 0000000000000000 x4 : 0000000000000000
[ 99.939872] x3 : 000000000002a5ab x2 : ffffffe53feed918
[ 99.945182] x1 : ffffffe53fee4a08 x0 : 000000000000008e
[ 99.950491] Call trace:
[ 99.952937] skb_panic+0x64/0x68
[ 99.956165] skb_put+0x7c/0x84
[ 99.959224] ath10k_sdio_irq_handler+0x740/0xbb8 [ath10k_sdio]
[ 99.965055] process_sdio_pending_irqs+0x58/0x1a4
[ 99.969758] sdio_run_irqs+0x34/0x60
[ 99.973329] sdio_irq_work+0x1c/0x28
[ 99.974930] cros-ec-spi spi2.0: SPI transfer timed out
[ 99.976904] process_one_work+0x210/0x410
[ 99.976911] worker_thread+0x234/0x3dc
[ 99.976923] kthread+0x120/0x130
[ 99.982090] cros-ec-spi spi2.0: spi transfer failed: -110
[ 99.986054] ret_from_fork+0x10/0x18
[ 99.986063] Code: aa1403e2 2a1503e4 a90023e9 97e37d1a (d4210000)
[ 99.986068] ---[ end trace cb6d948c5a0fd6c7 ]---
[ 100.017250] Kernel panic - not syncing: Fatal exception
[ 100.018879] cros-ec-spi spi2.0: Command xfer error (err:-110)
[ 100.023659] SMP: stopping secondary CPUs
[ 100.023703] Kernel Offset: 0x251dc00000 from 0xffffff8008000000
[ 100.023707] CPU features: 0x0,2188200c
[ 100.023709] Memory Limit: none
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 8 bytes will be considered as ath10k_htc_hdr,
but actually the 8 bytes is not the ath10k_htc_hdr, so the act_len
from this ath10k_htc_hdr is not correct, if it is a big value, such
as 57013, it will trigger skb_panic.
Drop the skb with invalid length will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/ath/ath10k/htt_rx.c:2143:2-31: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WiFi firmware found on sm8150 requires that the QDSS clock is
ticking in order to operate, so add an optional clock to the binding to
allow this to be specified in the sm8150 dts and add the clock to the
list of clocks in the driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The description of ath10k_pci_dump_memory_sram() is inaccurate, an error
can never be returned, it is always the length. Update the comment to
reflect.
Fixes: 219cc084c6 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_pci_dump_memory_reg() will try to access memory of type
ATH10K_MEM_REGION_TYPE_IOREG however, if a hardware restart is in progress
this can crash a system.
Individual ioread32() time has been observed to jump from 15-20 ticks to >
80k ticks followed by a secure-watchdog bite and a system reset.
Work around this corner case by only issuing the read transaction when the
driver state is ATH10K_STATE_ON.
Tested-on: QCA9988 PCI 10.4-3.9.0.2-00044
Fixes: 219cc084c6 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/ath/wil6210/main.c:765:1-14: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/txrx.c:1143:1-19: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/wmi.c:1516:4-23: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/wmi.c:1523:4-23: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/wmi.c:1538:4-30: WARNING: Assignment of 0/1 to bool variable
drivers/net/wireless/ath/wil6210/wmi.c:1545:4-30: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/ath/ath9k/ar9003_aic.c:409:2-12: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
-----BEGIN PGP SIGNATURE-----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=Ovcw
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First set of patches intended for v5.6
* Support new versions of the FTM FW APIs;
* Fix an old bug in D3 (WoWLAN);
* A couple of fixes/improvements in the receive-buffers code;
* Fix in the debugging where we were skipping one TXQ;
* Support new version of the beacon template FW API;
* Print some extra information when the driver is loaded;
* Some debugging infrastructure (aka. yoyo) updates;
* Support for a new HW version;
* Second phase of device configuration work started;
* Some clean-ups;
Bump version to 0.8.2-k
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provide support to change or retrieve RSS hash options for a flow type.
The supported flow-types are: tcp4, tcp6, udp4, udp6, sctp4, sctp6.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set configuration for hardware RSS tables for VFs.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Attempt to optimize TCAM entries and reduce table resource usage by
searching for profiles that can be reused. Provide resource cleanup
of both hardware and software structures.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Write the hardware tables based on the populated software structures.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Store the TCAM entry with the profile data and the VSI group in the
respective SW structures. This will be subsequently used to write out
the tables to hardware.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl4rTdoACgkQSD+KveBX
+j5wiAgAtlGxIVKMpbJN7DIJNQ3rLGwTjPdVUFSRvHB+krVV9/ym02bIBIEphSPu
ZEF53eJMtJ0XIdUjvAyKA+zJg9p12vewbGpYV/LdjBNikHatMPGvR4grDgB9pnqT
tIxH6b4vzh5p/bMcP5l4yuVG6pf/ERdxQqsa93Op9xJzOkMH+A2KA/G32VHL2OmH
619hrWRVA/UVG0wUcOaX6ra+QA5EQ3lhcrvqL702k4JhIZPtG7Ndmm0+Z0nrDiIm
oXfc1236nc3emkijQczEZ+6oYiuYQ7WSKxZeS+8Bnmc3ZZ2w2RZrC7UCOadGzu12
+0XYfMsD2FWwEim52IZK/VMPtykjZw==
=i5Au
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-01-24
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
Merge conflict: once merge with net-next, a contextual conflict will
appear in drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c
since the code moved in net-next.
To resolve, just delete ALL of the conflicting hunk from net.
So sorry for the small mess ..
For -stable v5.4:
('net/mlx5: Update the list of the PCI supported devices')
('net/mlx5: Fix lowest FDB pool size')
('net/mlx5e: kTLS, Fix corner-case checks in TX resync flow')
('net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path')
('net/mlx5: Eswitch, Prevent ingress rate configuration of uplink rep')
('net/mlx5e: kTLS, Remove redundant posts in TX resync flow')
('net/mlx5: DR, Enable counter on non-fwd-dest objects')
('net/mlx5: DR, use non preemptible call to get the current cpu number')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
React to the TC messages that were introduced in a preceding patch and
configure egress maximum shaper as appropriate. TBF can be used as a root
qdisc or under one of PRIO or strict ETS bands.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow configuration of burst size together with shaper rate,
extend mlxsw_sp_port_ets_maxrate_set() with a burst_size argument. Convert
call sites to pass 0 (for default).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lower limit of burst size configuration is dependent on system type. Add a
datum to track the value. Initialize as appropriate in mlxsw_spX_init().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the port speeds grow, the current value of "unlimited shaper",
200000000Kbps, might become lower than the actually supported speeds. Bump
it to the maximum value that fits in the corresponding QEEC field, which is
about 2.1Tbps.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QEEC register configures scheduling elements. One of the bits of
configuration is the burst size to use for the shaper installed on the
element. Add the necessary fields to support this configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the RED Qdisc is unoffloaded, it needs to reduce the reported backlog
by the amount that is in the HW, so that only the SW backlog is contained
in the counter. The same thing will need to be done by TBF, and likely any
other leaf Qdisc as well.
Extract a helper mlxsw_sp_qdisc_leaf_unoffload() and call it from
mlxsw_sp_qdisc_red_unoffload().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a wrapper around mlxsw_sp_qdisc_collect_tc_stats() and
mlxsw_sp_qdisc_update_stats() for the simple case of doing both in one go:
mlxsw_sp_qdisc_get_class_stats(). Dispatch to that function from
mlxsw_sp_qdisc_get_red_stats(). This new function will be useful for other
leaf Qdiscs as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract from mlxsw_sp_qdisc_get_prio_stats() two new functions:
mlxsw_sp_qdisc_collect_tc_stats() to accumulate stats for that one TC only,
and mlxsw_sp_qdisc_update_stats() that makes the stats relative to base
values stored earlier. Use them from mlxsw_sp_qdisc_get_red_stats().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cxgb3 driver for "Chelsio T3-based gigabit and 10Gb Ethernet
adapters" implements a custom ioctl as SIOCCHIOCTL/SIOCDEVPRIVATE in
cxgb_extension_ioctl().
One of the subcommands of the ioctl is CHELSIO_GET_MEM, which appears
to read memory directly out of the adapter and return it to userspace.
It's not entirely clear what the contents of the adapter memory
contains, but the assumption is that it shouldn't be accessible to all
users.
So add a CAP_NET_ADMIN check to the CHELSIO_GET_MEM case. Put it after
the is_offload() check, which matches two of the other subcommands in
the same function which also check for is_offload() and CAP_NET_ADMIN.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of XDP in native mode for hv_netvsc driver, and
transparently sets the XDP program on the associated VF NIC as well.
Setting / unsetting XDP program on synthetic NIC (netvsc) propagates to
VF NIC automatically. Setting / unsetting XDP program on VF NIC directly
is not recommended, also not propagated to synthetic NIC, and may be
overwritten by setting of synthetic NIC.
The Azure/Hyper-V synthetic NIC receive buffer doesn't provide headroom
for XDP. We thought about re-use the RNDIS header space, but it's too
small. So we decided to copy the packets to a page buffer for XDP. And,
most of our VMs on Azure have Accelerated Network (SRIOV) enabled, so
most of the packets run on VF NIC. The synthetic NIC is considered as a
fallback data-path. So the data copy on netvsc won't impact performance
significantly.
XDP program cannot run with LRO (RSC) enabled, so you need to disable LRO
before running XDP:
ethtool -K eth0 lro off
XDP actions not yet supported:
XDP_REDIRECT
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 7587935cfa ("net: bcmgenet: move NAPI initialization to
ring initialization") moved the code, this used to be
netif_tx_napi_add(), but we lost that small semantic change in the
process, restore that.
Fixes: 7587935cfa ("net: bcmgenet: move NAPI initialization to ring initialization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the print_hex_dump() helper, instead of open-coding the same operations.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic device API to get phy mode to fix probe failure
with ACPI based devices.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create an extraction sequence based on the packet header protocols to be
programmed and allocate a flow profile for the extraction sequence.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable the driver to write the filtering hardware tables to allow for
changing of RSS rules. Upon loading of DDP package, a minimal configuration
should be written to hardware.
Introduce and initialize structures for storing configuration and make
the top level calls to configure the RSS tables to initial values. A packet
segment will be created but nothing is written to hardware yet.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When TCP out-of-order is identified (unexpected tcp seq mismatch), driver
analyzes the packet and decides what handling should it get:
1. go to accelerated path (to be encrypted in HW),
2. go to regular xmit path (send w/o encryption),
3. drop.
Packets marked with skb->decrypted by the TLS stack in the TX flow skips
SW encryption, and rely on the HW offload.
Verify that such packets are never sent un-encrypted on the wire.
Add a WARN to catch such bugs, and prefer dropping the packet in these cases.
Fixes: 46a3ea9807 ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The call to tx_post_resync_params() is done earlier in the flow,
the post of the control WQEs is unnecessarily repeated. Remove it.
Fixes: 700ec49742 ("net/mlx5e: kTLS, Fix missing SQ edge fill")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There are the following cases:
1. Packet ends before start marker: bypass offload.
2. Packet starts before start marker and ends after it: drop,
not supported, breaks contract with kernel.
3. packet ends before tls record info starts: drop,
this packet was already acknowledged and its record info
was released.
Add the above as comment in code.
Mind possible wraparounds of the TCP seq, replace the simple comparison
with a call to the TCP before() method.
In addition, remove logic that handles negative sync_len values,
as it became impossible.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Fixes: 46a3ea9807 ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently VF in LEGACY mode are not able to go up. Also in OFFLOADS
mode, when switching to it first time, VF can go up independently to
his representor, which is not expected.
Perform clearing of VF config when switching modes and set link state
to AUTO as default value. Also, when switching to OFFLOADS mode set
link state to DOWN, which allow VF link state to be controlled by its
REP.
Fixes: 1ab2068a4c ("net/mlx5: Implement vports admin state backup/restore")
Fixes: 556b9d16d3 ("net/mlx5: Clear VF's configuration on disabling SRIOV")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use raw_smp_processor_id instead of smp_processor_id() otherwise we will
get the following trace in debug-kernel:
BUG: using smp_processor_id() in preemptible [00000000] code: devlink
caller is dr_create_cq.constprop.2+0x31d/0x970 [mlx5_core]
Call Trace:
dump_stack+0x9a/0xf0
debug_smp_processor_id+0x1f3/0x200
dr_create_cq.constprop.2+0x31d/0x970
genl_family_rcv_msg+0x5fd/0x1170
genl_rcv_msg+0xb8/0x160
netlink_rcv_skb+0x11e/0x340
Fixes: 297cccebdc ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Since the implementation relies on limiting the VF transmit rate to
simulate ingress rate limiting, and since either uplink representor or
ecpf are not associated with a VF, we limit the rate limit configuration
for those ports.
Fixes: fcb64c0f56 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code handles only counters that attached to dest, we still
have the cases where we have counter on non-dest, like over drop etc.
Fixes: 6a48faeeca ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the upcoming ConnectX-7 device ID.
Fixes: 85327a9c41 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The pool sizes represent the pool sizes in the fw. when we request
a pool size from fw, it will return the next possible group.
We track how many pools the fw has left and start requesting groups
from the big to the small.
When we start request 4k group, which doesn't exists in fw, fw
wants to allocate the next possible size, 64k, but will fail since
its exhausted. The correct smallest pool size in fw is 128 and not 4k.
Fixes: e52c280240 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a hw_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series provides updates to mlx5 driver.
1) Misc small cleanups
2) Some SW steering updates including header copy support
3) Full ethtool statistics support for E-Switch uplink representor
Some refactoring was required to share the bare-metal NIC ethtool
stats with the Uplink representor. On Top of this Vlad converts the
ethtool stats support in E-Swtich vports representors to use the mlx5e
"stats groups" infrastructure and then applied all applicable stats
to the uplink representor netdev.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl4pPoQACgkQSD+KveBX
+j43XAf/fFagUye8gFCFI2Yg0tbaDXKKvp+Z6zfA8K8URVXSksSE6dr9VraWVO8C
dtYvyv+u9IKerdi0j/uuHOHvuYAr/MwY9AV/uxltU3bxKfIbQp6puRoSU5CPVKZN
20dqN/zpbm0Tzk/k8WSpeZaPg+im5sFn7HUIoSL14AJW6KrjU6jP/pBjQMJVIcMs
Yq+QBsC9PWSfH3O4MX5qYg8IRbtXWIQplVeSU9A5Rj9+ParbMmyKOhRwq7ZcNDMM
UMA/y2z7FZ0ENQ1dajs4Yu/MiAX50sfU9M0TXwbCxim5437l26lQw3sum62Zr/Oz
rmyyVhNAX7Vm+SkHKaX85p2pOcejkQ==
=GB6e
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-01-22
This series provides updates to mlx5 driver.
1) Misc small cleanups
2) Some SW steering updates including header copy support
3) Full ethtool statistics support for E-Switch uplink representor
Some refactoring was required to share the bare-metal NIC ethtool
stats with the Uplink representor. On Top of this Vlad converts the
ethtool stats support in E-Swtich vports representors to use the mlx5e
"stats groups" infrastructure and then applied all applicable stats
to the uplink representor netdev.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 5.5.3.2 of the datasheet says,
If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or
Excessive Deferral (if enabled) errors occur, transmission ceases.
In this situation, the chip asserts a TXER interrupt rather than TXDN.
But the handler for the TXDN is the only way that the transmit queue
gets restarted. Hence, an aborted transmission can result in a watchdog
timeout.
This problem can be reproduced on congested link, as that can result in
excessive transmitter collisions. Another way to reproduce this is with
a FIFO Underrun, which may be caused by DMA latency.
In event of a TXER interrupt, prevent a watchdog timeout by restarting
transmission.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 4.3.1 of the datasheet says,
This bit [TXP] must not be set if a Load CAM operation is in
progress (LCAM is set). The SONIC will lock up if both bits are
set simultaneously.
Testing has shown that the driver sometimes attempts to set LCAM
while TXP is set. Avoid this by waiting for command completion
before and after giving the LCAM command.
After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than
SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until
!SONIC_CR_LCAM.
When in reset mode, take the opportunity to reset the CAM Enable
register.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several issues relating to command register usage during
chip initialization.
Firstly, the SONIC sometimes comes out of software reset with the
Start Timer bit set. This gets logged as,
macsonic macsonic eth0: sonic_init: status=24, i=101
Avoid this by giving the Stop Timer command earlier than later.
Secondly, the loop that waits for the Read RRA command to complete has
the break condition inverted. That's why the for loop iterates until
its termination condition. Call the helper for this instead.
Finally, give the Receiver Enable command after clearing interrupts,
not before, to avoid the possibility of losing an interrupt.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the SONIC's DMA engine is idle before altering the transmit
and receive descriptors. Add a helper for this as it will be needed
again.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as the driver is finished with a receive buffer it allocs a new
one and overwrites the corresponding RRA entry with a new buffer pointer.
Problem is, the buffer pointer is split across two word-sized registers.
It can't be updated in one atomic store. So this operation races with the
chip while it stores received packets and advances its RRP register.
This could result in memory corruption by a DMA write.
Avoid this problem by adding buffers only at the location given by the
RWP register, in accordance with the National Semiconductor datasheet.
Re-factor this code into separate functions to calculate a RRA pointer
and to update the RWP.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After sonic_tx_timeout() calls sonic_init(), it can happen that
sonic_rx() will subsequently encounter a receive descriptor with no
flags set. Remove the comment that says that this can't happen.
When giving a receive descriptor to the SONIC, clear the descriptor
status field. That way, any rx descriptor with flags set can only be
a newly received packet.
Don't process a descriptor without the LPKT bit set. The buffer is
still in use by the SONIC.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PHY IDs for the DP83825CS, DP83825CM and the DP83825S devices to the
DP83822 driver.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phy IDs to the DP83822 phy driver for the DP83826N
and the DP83826NC devices. The register map and features
are the same for basic enablement.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Tested-by: Yonggen Xu <Yonggen.Xu@dell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeKX2wAAoJEG4XJFUm622bG8QH/3+QXaSJAVqzbQh2boy7aS88
xhrrnh+bSqWY0ChMk0Z73RF8Ek0WlO+os4uN1cbWIWujrdQUPbTBtOwX4d0TzTue
E3tBFPiHTlVtU43z1bsprA+6EE7fqt/H2lWtlxk0IHzeiQY9NcB6BlDKKCzk5Hib
aMb5HCQy4JmSK83E60HLM9L4nEmEP+yveaKL7uaAZw+qkmyk2mT6um0TlmOYVoNG
9V6k3OZto8LvyV6jKPZgVI6QBATnwHDxlWgooYRj54PuCj9hTbR2mcuUL2QyQeze
AX2QNI+1kWIrAiDaU/lOj8579SiUl36iqtuKmtLhDnSe1GxDkrzmawtz3aGDm4k=
=VZox
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program
consumes the skb, we need to clear the napi.skb (or risk
a use-after-free) and release the mutex (or risk a deadlock)
WARNING: lock held when returning to user space!
5.5.0-rc6-syzkaller #0 Not tainted
------------------------------------------------
syz-executor.0/455 is leaving the kernel with locks still held!
1 lock held by syz-executor.0/455:
#0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Petar Penkov <ppenkov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reload (or module unload), the router block is de-initialized.
Among other things, this results in the removal of a default multicast
route from each active virtual router (VRF). These default routes are
configured during initialization to trap packets to the CPU. In
Spectrum-2, unlike Spectrum-1, multicast routes are implemented using
ACL rules.
Since the router block is de-initialized before the ACL block, it is
possible that the ACL rules corresponding to the default routes are
deleted while being accessed by the ACL delayed work that queries rules'
activity from the device. This can result in a rare use-after-free [1].
Fix this by protecting the rules list accessed by the delayed work with
a lock. We cannot use a spinlock as the activity read operation is
blocking.
[1]
[ 123.331662] ==================================================================
[ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78
[ 123.357080]
[ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209
[ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
[ 123.385970] Call Trace:
[ 123.388734] dump_stack+0xc6/0x11e
[ 123.392568] print_address_description.constprop.4+0x21/0x340
[ 123.403236] __kasan_report.cold.8+0x76/0xb1
[ 123.414884] kasan_report+0xe/0x20
[ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.444034] process_one_work+0xb06/0x19a0
[ 123.453731] worker_thread+0x91/0xe90
[ 123.467348] kthread+0x348/0x410
[ 123.476847] ret_from_fork+0x24/0x30
[ 123.480863]
[ 123.482545] Allocated by task 73:
[ 123.486273] save_stack+0x19/0x80
[ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230
[ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0
[ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820
[ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690
[ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0
[ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990
[ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60
[ 123.532752] process_one_work+0xb06/0x19a0
[ 123.537352] worker_thread+0x91/0xe90
[ 123.541471] kthread+0x348/0x410
[ 123.545103] ret_from_fork+0x24/0x30
[ 123.549113]
[ 123.550795] Freed by task 518:
[ 123.554231] save_stack+0x19/0x80
[ 123.557958] __kasan_slab_free+0x125/0x170
[ 123.562556] kfree+0xd7/0x3a0
[ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0
[ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130
[ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260
[ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290
[ 123.588091] mlxsw_sp_vr_put+0x1db/0x350
[ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0
[ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360
[ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470
[ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120
[ 123.612260] mlxsw_sp_router_fini+0x137/0x384
[ 123.617152] mlxsw_sp_fini+0x30a/0x4a0
[ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600
[ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0
[ 123.634176] devlink_reload+0xb4/0x380
[ 123.638391] devlink_nl_cmd_reload+0x610/0x700
[ 123.643382] genl_rcv_msg+0x6a8/0xdc0
[ 123.647497] netlink_rcv_skb+0x134/0x3a0
[ 123.651904] genl_rcv+0x29/0x40
[ 123.655436] netlink_unicast+0x4d4/0x700
[ 123.659843] netlink_sendmsg+0x7c0/0xc70
[ 123.664251] __sys_sendto+0x265/0x3c0
[ 123.668367] __x64_sys_sendto+0xe2/0x1b0
[ 123.672773] do_syscall_64+0xa0/0x530
[ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 123.682552]
[ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500
[ 123.684238] which belongs to the cache kmalloc-128 of size 128
[ 123.698261] The buggy address is located 32 bytes inside of
[ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580)
[ 123.711303] The buggy address belongs to the page:
[ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0
[ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500
[ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
[ 123.743315] page dumped because: kasan: bad access detected
[ 123.749562]
[ 123.751241] Memory state around the buggy address:
[ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 123.780904] ^
[ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.801883] ==================================================================
Fixes: cf7221a4f5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certain platforms, it causes USB reset periodically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When linking ON, the patch of flow control has to be reset. This
makes sure the patch works normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the runtime resume doesn't work normally for linking change.
1. Reset the settings and status of runtime suspend.
2. Sync the linking status.
3. Poll the linking change.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command. Some of the commands are handled in readrids(),
where the user controlled command is converted into a driver-internal
value called "ridcode".
There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which
correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM
respectively. These commands both have checks that the user has
CAP_NET_ADMIN, with the comment that "Only super-user can read WEP
keys", otherwise they return -EPERM.
However there is another command value, AIRORRID, that lets the user
specify the ridcode value directly, with no other checks. This means
the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and
AIROGWEPKNV.
Fix it by moving the CAP_NET_ADMIN check out of the command handling
and instead do it later based on the ridcode. That way regardless of
whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed
in using AIRORID, we always do the CAP_NET_ADMIN check.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command and a length. Some of the commands are handled in
readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes.
That buffer is then passed to PC4500_readrid(), which has two cases.
The else case does some setup and then reads up to RIDSIZE bytes from
the hardware into the kmalloc()'ed buffer.
Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer:
// read the rid length field
bap_read(ai, pBuf, 2, BAP1);
// length for remaining part of rid
len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2;
...
// read remainder of the rid
rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1);
PC4500_readrid() then returns to readrids() which does:
len = comp->len;
if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) {
Where comp->len is the user controlled length field.
So if the "rid length field" returned by the hardware is < 2048, and
the user requests 2048 bytes in comp->len, we will leak the previous
contents of the kmalloc()'ed buffer to userspace.
Fix it by kzalloc()'ing the buffer.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-01-22
The following pull-request contains BPF updates for your *net-next* tree.
We've added 92 non-merge commits during the last 16 day(s) which contain
a total of 320 files changed, 7532 insertions(+), 1448 deletions(-).
The main changes are:
1) function by function verification and program extensions from Alexei.
2) massive cleanup of selftests/bpf from Toke and Andrii.
3) batched bpf map operations from Brian and Yonghong.
4) tcp congestion control in bpf from Martin.
5) bulking for non-map xdp_redirect form Toke.
6) bpf_send_signal_thread helper from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend stats group array of uplink representor with all stats that are
available for PF in legacy mode, besides ipsec and TLS which are not
supported.
Don't output vport stats for uplink representor because they are already
handled by 802_3 group (with different names: {tx|rx}_{bytes|packets}_phy).
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Q counters were disabled for all types of representors to prevent an issue
where there is not enough resources to init q counters for 127 representor
instances. Enable q counters only for uplink representors to support
"rx_out_of_buffer", "rx_if_down_packets" counters in ethtool.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to support all of the supported stats that are available in legacy
mode for switchdev uplink representors, convert rep stats infrastructure to
reuse struct mlx5e_stats_grp that is already used when device is in legacy
mode. Refactor rep code to use array of mlx5e_stats_grp
structures (constructed using macros provided by stats infra) to
fill/update stats, instead of fixed hardcoded set of values. This approach
allows to easily extend representors with new stats types.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Don't copy all of the stats groups used for mlx5e ethernet NIC profile,
have a separate stats groups for IPoIB with the set of the needed stats
only.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Convert stats groups array to array of "stats group" pointers to allow
sharing and individual selection of groups per profile as illustrated in
the next patches.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Introduce new macros to declare stats callbacks and groups, for better
code reuse and for individual groups selection per profile which will be
introduced in next patches.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Attach stats groups array to the profiles and make the stats utility
functions (get_num, update, fill, fill_strings) generic and use the
profile->stats_grps rather the hardcoded NIC stats groups.
This will allow future extension to have per profile stats groups.
In this patch mlx5e NIC and IPoIB will still share the same stats
groups.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Clean up the code and allows to call uplink rep init/cleanup
from different location later.
To be used later for a new uplink representor mode.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allow connecting SW steering source table to a lower/same level
destination table.
Lifting this limitation is required to support Connection Tracking.
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Modify header supports ADD/SET and from this patch
also COPY. Copy allows to copy header fields and
metadata.
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Modify set actions are not supported on both tx
and rx, added a check for that.
Also refactored the code in a way that every modify
action has his own functions, this needed so in the
future we could add copy action more smoothly.
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the flowtables offload all the devices in the flowtables
share the same flow_block. An offload rule will be installed on
all the devices. This scenario is not correct.
It is no problem if there are only two devices in the flowtable,
The rule with ingress and egress on the same device can be reject
by driver.
But more than two devices in the flowtable will install the wrong
rules on hardware.
For example:
Three devices in a offload flowtables: dev_a, dev_b, dev_c
A rule ingress from dev_a and egress to dev_b:
The rule will install on device dev_a.
The rule will try to install on dev_b but failed for ingress
and egress on the same device.
The rule will install on dev_c. This is not correct.
The flowtables offload avoid this case through restricting the ingress dev
with FLOW_DISSECTOR_KEY_META.
So the mlx5e driver also should support the FLOW_DISSECTOR_KEY_META parse.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Acked-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix the following sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads_chains.c:35:20: warning: symbol 'ESW_POOLS' was not declared. Should it be static?
Fixes: 39ac237ce0 ("net/mlx5: E-Switch, Refactor chains and priorities")
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Acked-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
since mlx5 hardware can segment correctly TSO packets on VXLAN over VLAN
topologies, CPU usage can improve significantly if we enable tunnel
offloads in dev->vlan_features, like it was done in the past with other
NIC drivers (e.g. mlx4, be2net and ixgbe).
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use "%zu" for size_t. Seen on ARM allmodconfig:
drivers/net/ethernet/mellanox/mlx5/core/wq.c: In function 'mlx5_wq_cyc_wqe_dump':
include/linux/kern_levels.h:5:18: warning: format '%ld' expects argument of type 'long int', but argument 5 has type 'size_t' {aka 'unsigned int'} [-Wformat=]
Fixes: 130c7b46c9 ("net/mlx5e: TX, Dump WQs wqe descriptors on CQE with error events")
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The first batch of driver conversions missed a few cases where we can
use phy_do_ioctl too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL
skbs") introduces batching of GRO_NORMAL packets in napi_frags_finish,
and commit 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") adds the same to napi_skb_finish. However,
dev_gro_receive (that is called just before napi_{frags,skb}_finish) can
also pass skbs to the networking stack: e.g., when the GRO session is
flushed, napi_gro_complete is called, which passes pp directly to
netif_receive_skb_internal, skipping napi->rx_list. It means that the
packet stored in pp will be handled by the stack earlier than the
packets that arrived before, but are still waiting in napi->rx_list. It
leads to TCP reorderings that can be observed in the TCPOFOQueue counter
in netstat.
This commit fixes the reordering issue by making napi_gro_complete also
use napi->rx_list, so that all packets going through GRO will keep their
order. In order to keep napi_gro_flush working properly, gro_normal_list
calls are moved after the flush to clear napi->rx_list.
iwlwifi calls napi_gro_flush directly and does the same thing that is
done by gro_normal_list, so the same change is applied there:
napi_gro_flush is moved to be before the flush of napi->rx_list.
A few other drivers also use napi_gro_flush (brocade/bna/bnad.c,
cortina/gemini.c, hisilicon/hns3/hns3_enet.c). The first two also use
napi_complete_done afterwards, which performs the gro_normal_list flush,
so they are fine. The latter calls napi_gro_receive right after
napi_gro_flush, so it can end up with non-empty napi->rx_list anyway.
Fixes: 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL skbs")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Cc: Alexander Lobakin <alobakin@dlink.ru>
Cc: Edward Cree <ecree@solarflare.com>
Acked-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
write_wakeup can happen in parallel with close/hangup where tty->disc_data
is set to NULL and the netdevice is freed thus also freeing
disc_data. write_wakeup accesses disc_data so we must prevent close from
freeing the netdev while write_wakeup has a non-NULL view of
tty->disc_data.
We also need to make sure that accesses to disc_data are atomic. Which can
all be done with RCU.
This problem was found by Syzkaller on SLCAN, but the same issue is
reproducible with the SLIP line discipline using an LTP test based on the
Syzkaller reproducer.
A fix which didn't use RCU was posted by Hillf Danton.
Fixes: 661f7fda21 ("slip: Fix deadlock in write_wakeup")
Fixes: a8e83b1753 ("slcan: Port write_wakeup deadlock fix from slip")
Reported-by: syzbot+017e491ae13c0068598a@syzkaller.appspotmail.com
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tyler Hall <tylerwhall@gmail.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: syzkaller@googlegroups.com
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this was to keep all the queues updated with
the Rx sequence numbers because unlikely yet possible
situations where queues can't understand if a specific
packet needs to be dropped or not.
Unfortunately, it was reported that this caused issues in
our DMA engine. We don't fully understand how this is related,
but this is being currently debugged. For now, just don't send
this notification to the Rx queues. This de-facto reverts my
commit 3c514bf831:
iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues
This issue was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=204873https://bugzilla.kernel.org/show_bug.cgi?id=205001
and others maybe.
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
CC: <stable@vger.kernel.org> # 5.3+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
./drivers/net/ethernet/amd/declance.c:611:14-15:
WARNING comparing pointer to 0
Replace "skb == 0" with "!skb".
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wan/hdlc_x25.c: In function ‘x25_ioctl’:
drivers/net/wan/hdlc_x25.c:256:7: warning: suggest parentheses around assignment used as truth value [-Wparentheses]
256 | if (ifr->ifr_settings.size = 0) {
| ^~~
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes some unnecessary return value assignments,
some duplicated printing in the caller, refines the judgment
of 0 and uses le16_to_cpu to replace __le16_to_cpu.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All kmalloc-based functions print enough information on failures.
So this patch removes the log in hclge_get_dfx_reg() when returns
ENOMEM.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch deletes some unnecessary blank lines and spaces to clean up
code, and in hclgevf_set_vlan_filter() moves the comment to the front
of hclgevf_send_mbx_msg().
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When gets vector fails, hclge_put_vector() should print out
the vector instead of vector_id in the log and return the wrong
vector_id to its caller.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function snprintf() writes at most size bytes (including the
terminating null byte ('\0') to str. Now, We can guarantee that the
parameter of size is lager than the length of str to be formatting
including its terminating null byte. So it's unnecessary to minus 1
for the input parameter 'size'.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro HCLGE_GET_DFX_REG_TYPE_CNT in hclge_dbg_get_dfx_bd_num()
and macro HCLGE_DFX_REG_BD_NUM in hclge_get_dfx_reg_bd_num()
have the same meaning, so just defines HCLGE_GET_DFX_REG_TYPE_CNT
in hclge_main.h.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reset_type means what kind of reset the driver is handling now,
so after initializing or reset, the reset_type of VF should be
set to HNAE3_NONE_RESET, otherwise, this unknown default value
may be a little misleading when the device is running.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver allocates pages for DMA with dev_alloc_pages(), which
calls alloc_pages_node() with the __GFP_MEMALLOC flag. So, in case
of OOM condition, HNS3 can get pages with pfmemalloc flag set.
So do not reuse the pages with pfmemalloc flag set because those
pages are reserved for special cases, such as low memory case.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error log printed by netdev_err() in the hns3_clean_tx_ring()
may spam the kernel log.
This patch uses hns3_rl_err() to ratelimit the error log in the
hns3_clean_tx_ring().
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o call skb_reset_network_header() before hdlc->xmit()
o change skb proto to HDLC (0x0019) before hdlc->xmit()
o call dev_queue_xmit_nit() before hdlc->xmit()
This changes make it possible to trace (tcpdump) outgoing layer2
(ETH_P_HDLC) packets
Additionally call skb_reset_network_header() after each skb_push() /
skb_pull().
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables you to configure mode (DTE/DCE), Modulo, Window, T1, T2, N2 via
sethdlc (which needs to be patched as well).
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable network drivers to use phy_do_ioctl.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new version of phy_do_ioctl that doesn't check whether net_device
is running. It will typically be used if suitable drivers attach the
PHY in probe already.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We just added phy_do_ioctl, but it turned out that we need another
version of this function that doesn't check whether net_device is
running. So rename phy_do_ioctl to phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
snprintf returns the number of bytes that would be written, which may be
greater than the the actual length to be written. Here use extra code to
handle this.
scnprintf returns the number of bytes that was actually written, just use
scnprintf to simplify the code.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of snprintf may be greater than the size of
HNS3_DBG_READ_LEN, use scnprintf instead in hns3_dbg_cmd_read.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PUDE event is handled and the link is up, update the port SPAN
buffer size according to the current speed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SPAN egress mirroring buffer size, it is needed to use a different
formula for Spectrum and Spectrum-2. Move the buffer size computation to
ops and implement new formula for Spectrum-2.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid duplication of code that is doing buffsize update and put it into
a separate helper function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PTP code queries directly PTYS register for port speed from
work scheduled upon PUDE event. Since the speed needs to be used for
SPAN buffer size computation as well, push the code into a separate
helper.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace rtl8169_ioctl with new generic function phy_do_ioctl.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of network drivers has the same glue code to use phy_mii_ioctl
as ndo_do_ioctl handler. So let's add such a generic ndo_do_ioctl
handler to phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SERDES statistics are valid for all members of the 6390 family,
not just the 6390 itself. Add the needed callbacks to all members of
the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
USXGMII supports passing link information in-band between PHY and MAC PCS,
add it to the list of protocols that support in-band AN mode.
Being a MAC-PHY protocol that can auto-negotiate link speeds up to 10
Gbps, we populate the initial supported mask with the entire spectrum of
link modes up to 10G that PHYLINK supports, and we let the driver reduce
that mask in its .phylink_validate method.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The APIs can be used by Ethernet drivers without actually loading a PHY
driver. This may become more widespread in the future with 802.3z
compatible MAC PCS devices being locally driven by the MAC driver when
configuring for a PHY mode with in-band negotiation.
Check that drv is not NULL before reading from it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, PHYLINK does not put the copper modes for 802.3bz
(NBASE-T) and 802.3an-2006 (10GBASE-T) in the PHY's supported mask, when
the PHY-MAC connection is a 10G-capable one (10GBase-KR, 10GBase-R,
USXGMII). One possible way through which the cable side can work at the
lower speed is by having the PHY emit PAUSE frames towards the MAC. So
fix that omission.
Also include the 2500Base-X fiber mode in this list while we're at it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
snps databook noted that physical coding sublayer (PCS) interface
that can be used when the MAC is configured for the TBI, RTBI, or
SGMII PHY interface. we have RGMII and SGMII in a SoC and it also
has the PCS block. it needs stmmac_init_phy and stmmac_mdio_register
function for initializing phy when it used RGMII interface.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a trap for NVE packets that the device decided to drop because their
overlay source MAC is multicast.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trap IDs and trap group used to report tunnel drops. Register
tunnel packet traps and associated tunnel trap group with devlink
during driver initialization.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move L3_DROPS case to appear after L2_DROPS case.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize ECN mapping registers during router init according to
INET_ECN_encapsulate() and INET_ECN_decapsulate().
For IP-in-IP encapsulation, this is required to ensure that ECN bits in
the underlay are set in accordance with the kernel. For decapsulation,
this is required to ensure that packets with invalid ECN combination in
underlay and overlay are trapped to the kernel and not forwarded.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register configures the actions that are done during IPinIP
decapsulation based on the ECN bits.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register performs mapping from overlay ECN to underlay ECN during
IPinIP encapsulation.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a trap for packets that the device decided to drop because they are
not supposed to be routed. For example, IGMP queries can be flooded by
the device in layer 2 and reach the router. Such packets should not be
routed and instead dropped.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRIF_DISABLED and ERIF_DISABLED are driver specific traps. Packets are
dropped for these reasons when they need to be routed through/from
existing router interfaces (RIF) which are disabled.
Add devlink driver-specific traps and mlxsw trap IDs used to report
these traps.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox, mlx5 E-Switch chains and prios
This series has two parts,
1) A merge commit with mlx5-next branch that include updates for mlx5
HW layouts needed for this and upcoming submissions.
2) From Paul, Increase the number of chains and prios
Currently the Mellanox driver supports offloading tc rules that
are defined on the first 4 chains and the first 16 priorities.
The restriction stems from the firmware flow level enforcement
requiring a flow table of a certain level to point to a flow
table of a higher level. This limitation may be ignored by setting
the ignore_flow_level bit when creating flow table entries.
Use unmanaged tables and ignore flow level to create more tables than
declared by fs_core steering. Manually manage the connections between the
tables themselves.
HW table is instantiated for every tc <chain,prio> tuple. The miss rule
of every table either jumps to the next <chain,prio> table, or continues
to slow_fdb. This logic is realized by following this sequence:
1. Create an auto-grouped flow table for the specified priority with
reserved entries
Reserved entries are allocated at the end of the flow table.
Flow groups are evaluated in sequence and therefore it is guaranteed
that the flow group defined on the last FTEs will be the last to evaluate.
Define a "match all" flow group on the reserved entries, providing
the platform to add table miss actions.
2. Set the miss rule action to jump to the next <chain,prio> table
or the slow_fdb.
3. Link the previous priority table to point to the new table by
updating its miss rule.
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A queue can't belong to multiple traffic classes. So, reject
any such configuration that results in overlapped queues for a
traffic class.
Fixes: b1396c2bd6 ("cxgb4: parse and configure TC-MQPRIO offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 can support 2 egress traffic management channels per port to
double the total number of traffic classes that can be configured.
In this configuration, if the class belongs to the other channel,
then all the queues must be bound again explicitly to the new class,
for the rate limit parameters on the other channel to take effect.
So, always explicitly bind all queues to the port rate limit traffic
class, regardless of the traffic management channel that it belongs
to. Also, only bind queues to port rate limit traffic class, if all
the queues don't already belong to an existing different traffic
class.
Fixes: 4ec4762d8e ("cxgb4: add TC-MATCHALL classifier egress offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
found a warning by the following command:
./scripts/checkpatch.pl -f drivers/net/phy/adin.c
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.rst
#628: FILE: drivers/net/phy/adin.c:628:
+ msleep(10);
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the serdes link is set to 2500 using interfce type 2500base-X, lower
link speeds over on the line side should still be supported.
Rate adaptation is done out of band, in our case using AQR PHYs this is
done using flow control.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control is used with 2500Base-X and AQR PHYs to do rate adaptation
between line side 100/1000 links and MAC running at 2.5G.
This is independent of the flow control configuration settled on line
side though AN.
In general, allowing the MAC to handle flow control even if not
negotiated with the link partner should not be a problem, so the patch
just enables it in all cases.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSN read can fail, for example on a kdump kernel without PCIe extended
config space support. If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading. Check the flag
to see if the stored DSN is valid before using it. Only VF reps
creation should fail without valid DSN.
Fixes: 03213a9965 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NTUPLE related firmware commands are sent to the wrong firmware
channel, causing all these commands to fail on new firmware that
supports the new firmware channel. Fix it by excluding the 3
NTUPLE firmware commands from the list for the new firmware channel.
Fixes: 760b6d3341 ("bnxt_en: Add support for 2nd firmware message channel.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable xmit_done is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The scope of function .ndo_tx_timeout was changed to include the hang
queue when a TX timeout event occurs. See commit 0290bd291c
("netdev: pass the stuck queue to the timeout handler") for more
details. Now, drivers don't need to identify which queue is stopped.
Drivers can simply use the queue index provided by dev_watchdog and
execute all actions needed to restore network traffic. This commit do
some cleanups into Intel ice driver to remove a redundant loop to find
stopped queue.
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
