System may crash after unloading ipmi_si.ko module
because a timer may remain and fire after the module cleaned up resources.
cleanup_one_si() contains the following processing.
/*
* Make sure that interrupts, the timer and the thread are
* stopped and will not run again.
*/
if (to_clean->irq_cleanup)
to_clean->irq_cleanup(to_clean);
wait_for_timer_and_thread(to_clean);
/*
* Timeouts are stopped, now make sure the interrupts are off
* in the BMC. Note that timers and CPU interrupts are off,
* so no need for locks.
*/
while (to_clean->curr_msg || (to_clean->si_state != SI_NORMAL)) {
poll(to_clean);
schedule_timeout_uninterruptible(1);
}
si_state changes as following in the while loop calling poll(to_clean).
SI_GETTING_MESSAGES
=> SI_CHECKING_ENABLES
=> SI_SETTING_ENABLES
=> SI_GETTING_EVENTS
=> SI_NORMAL
As written in the code comments above,
timers are expected to stop before the polling loop and not to run again.
But the timer is set again in the following process
when si_state becomes SI_SETTING_ENABLES.
=> poll
=> smi_event_handler
=> handle_transaction_done
// smi_info->si_state == SI_SETTING_ENABLES
=> start_getting_events
=> start_new_msg
=> smi_mod_timer
=> mod_timer
As a result, before the timer set in start_new_msg() expires,
the polling loop may see si_state becoming SI_NORMAL
and the module clean-up finishes.
For example, hard LOCKUP and panic occurred as following.
smi_timeout was called after smi_event_handler,
kcs_event and hangs at port_inb()
trying to access I/O port after release.
[exception RIP: port_inb+19]
RIP: ffffffffc0473053 RSP: ffff88069fdc3d80 RFLAGS: 00000006
RAX: ffff8806800f8e00 RBX: ffff880682bd9400 RCX: 0000000000000000
RDX: 0000000000000ca3 RSI: 0000000000000ca3 RDI: ffff8806800f8e40
RBP: ffff88069fdc3d80 R8: ffffffff81d86dfc R9: ffffffff81e36426
R10: 00000000000509f0 R11: 0000000000100000 R12: 0000000000]:000000
R13: 0000000000000000 R14: 0000000000000246 R15: ffff8806800f8e00
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0000
--- <NMI exception stack> ---
To fix the problem I defined a flag, timer_can_start,
as member of struct smi_info.
The flag is enabled immediately after initializing the timer
and disabled immediately before waiting for timer deletion.
Fixes: 0cfec916e8 ("ipmi: Start the timer and thread on internal msgs")
Signed-off-by: Yamazaki Masamitsu <m-yamazaki@ah.jp.nec.com>
[Adjusted for recent changes in the driver.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This is signed by my new key (919BFF81), which is now signed by my
old key.
This is a fairly large rework of the IPMI code, along with a bunch
of smaller fixes. The major changes have been in the next tree for
a couple of months, so they should be good to do in.
- Some users had IPMI systems where the GUID of the IPMI controller
could change. So rescanning of the GUID was added. The naming of
some sysfs things was dependent on the GUID, however, so this
resulted in the sysfs interface code in IPMI changing to remove that
dependency and name the IPMI BMCs like other sysfs devices.
- The ipmi_si_intf.c code was fairly bloated with all the different
discovery methods (PCI, ACPI, SMBIOS, OF, platform, module parameters,
hot add). The structure of how the interfaces were added was redone
to make them more modular, then the individual methods were pulled
out into their own files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8zFf
-----END PGP SIGNATURE-----
Merge tag 'ipmi-for-4.15' of git://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"This is a fairly large rework of the IPMI code, along with a bunch of
smaller fixes. The major changes have been in the next tree for a
couple of months, so they should be good to do in.
- Some users had IPMI systems where the GUID of the IPMI controller
could change. So rescanning of the GUID was added. The naming of
some sysfs things was dependent on the GUID, however, so this
resulted in the sysfs interface code in IPMI changing to remove
that dependency and name the IPMI BMCs like other sysfs devices.
- The ipmi_si_intf.c code was fairly bloated with all the different
discovery methods (PCI, ACPI, SMBIOS, OF, platform, module
parameters, hot add). The structure of how the interfaces were
added was redone to make them more modular, then the individual
methods were pulled out into their own files"
* tag 'ipmi-for-4.15' of git://github.com/cminyard/linux-ipmi: (48 commits)
ipmi_si: Delete an error message for a failed memory allocation in try_smi_init()
ipmi_si: fix memory leak on new_smi
ipmi: remove redundant initialization of bmc
ipmi: pr_err() strings should end with newlines
ipmi: Clean up some print operations
ipmi: Make the DMI probe into a generic platform probe
ipmi: Make the IPMI proc interface configurable
ipmi_ssif: Add device attrs for the things in proc
ipmi_si: Add device attrs for the things in proc
ipmi_si: remove ipmi_smi_alloc() function
ipmi_si: Move port and mem I/O handling to their own files
ipmi_si: Get rid of unused spacing and port fields
ipmi_si: Move PARISC handling to another file
ipmi_si: Move PCI setup to another file
ipmi_si: Move platform device handling to another file
ipmi_si: Move hardcode handling to a separate file.
ipmi_si: Move the hotmod handling to another file.
ipmi_si: Change ipmi_si_add_smi() to take just I/O info
ipmi_si: Move io setup into io structure
ipmi_si: Move irq setup handling into the io struct
...
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.15:
API:
- Disambiguate EBUSY when queueing crypto request by adding ENOSPC.
This change touches code outside the crypto API.
- Reset settings when empty string is written to rng_current.
Algorithms:
- Add OSCCA SM3 secure hash.
Drivers:
- Remove old mv_cesa driver (replaced by marvell/cesa).
- Enable rfc3686/ecb/cfb/ofb AES in crypto4xx.
- Add ccm/gcm AES in crypto4xx.
- Add support for BCM7278 in iproc-rng200.
- Add hash support on Exynos in s5p-sss.
- Fix fallback-induced error in vmx.
- Fix output IV in atmel-aes.
- Fix empty GCM hash in mediatek.
Others:
- Fix DoS potential in lib/mpi.
- Fix potential out-of-order issues with padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
lib/mpi: call cond_resched() from mpi_powm() loop
crypto: stm32/hash - Fix return issue on update
crypto: dh - Remove pointless checks for NULL 'p' and 'g'
crypto: qat - Clean up error handling in qat_dh_set_secret()
crypto: dh - Don't permit 'key' or 'g' size longer than 'p'
crypto: dh - Don't permit 'p' to be 0
crypto: dh - Fix double free of ctx->p
hwrng: iproc-rng200 - Add support for BCM7278
dt-bindings: rng: Document BCM7278 RNG200 compatible
crypto: chcr - Replace _manual_ swap with swap macro
crypto: marvell - Add a NULL entry at the end of mv_cesa_plat_id_table[]
hwrng: virtio - Virtio RNG devices need to be re-registered after suspend/resume
crypto: atmel - remove empty functions
crypto: ecdh - remove empty exit()
MAINTAINERS: update maintainer for qat
crypto: caam - remove unused param of ctx_map_to_sec4_sg()
crypto: caam - remove unneeded edesc zeroization
crypto: atmel-aes - Reset the controller before each use
crypto: atmel-aes - properly set IV after {en,de}crypt
hwrng: core - Reset user selected rng by writing "" to rng_current
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle are:
- Another attempt at enabling cross-release lockdep dependency
tracking (automatically part of CONFIG_PROVE_LOCKING=y), this time
with better performance and fewer false positives. (Byungchul Park)
- Introduce lockdep_assert_irqs_enabled()/disabled() and convert
open-coded equivalents to lockdep variants. (Frederic Weisbecker)
- Add down_read_killable() and use it in the VFS's iterate_dir()
method. (Kirill Tkhai)
- Convert remaining uses of ACCESS_ONCE() to
READ_ONCE()/WRITE_ONCE(). Most of the conversion was Coccinelle
driven. (Mark Rutland, Paul E. McKenney)
- Get rid of lockless_dereference(), by strengthening Alpha atomics,
strengthening READ_ONCE() with smp_read_barrier_depends() and thus
being able to convert users of lockless_dereference() to
READ_ONCE(). (Will Deacon)
- Various micro-optimizations:
- better PV qspinlocks (Waiman Long),
- better x86 barriers (Michael S. Tsirkin)
- better x86 refcounts (Kees Cook)
- ... plus other fixes and enhancements. (Borislav Petkov, Juergen
Gross, Miguel Bernal Marin)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
locking/x86: Use LOCK ADD for smp_mb() instead of MFENCE
rcu: Use lockdep to assert IRQs are disabled/enabled
netpoll: Use lockdep to assert IRQs are disabled/enabled
timers/posix-cpu-timers: Use lockdep to assert IRQs are disabled/enabled
sched/clock, sched/cputime: Use lockdep to assert IRQs are disabled/enabled
irq_work: Use lockdep to assert IRQs are disabled/enabled
irq/timings: Use lockdep to assert IRQs are disabled/enabled
perf/core: Use lockdep to assert IRQs are disabled/enabled
x86: Use lockdep to assert IRQs are disabled/enabled
smp/core: Use lockdep to assert IRQs are disabled/enabled
timers/hrtimer: Use lockdep to assert IRQs are disabled/enabled
timers/nohz: Use lockdep to assert IRQs are disabled/enabled
workqueue: Use lockdep to assert IRQs are disabled/enabled
irq/softirqs: Use lockdep to assert IRQs are disabled/enabled
locking/lockdep: Add IRQs disabled/enabled assertion APIs: lockdep_assert_irqs_enabled()/disabled()
locking/pvqspinlock: Implement hybrid PV queued/unfair locks
locking/rwlocks: Fix comments
x86/paravirt: Set up the virt_spin_lock_key after static keys get initialized
block, locking/lockdep: Assign a lock_class per gendisk used for wait_for_completion()
workqueue: Remove now redundant lock acquisitions wrt. workqueue flushes
...
Pull general security subsystem updates from James Morris:
"TPM (from Jarkko):
- essential clean up for tpm_crb so that ARM64 and x86 versions do
not distract each other as much as before
- /dev/tpm0 rejects now too short writes (shorter buffer than
specified in the command header
- use DMA-safe buffer in tpm_tis_spi
- otherwise mostly minor fixes.
Smack:
- base support for overlafs
Capabilities:
- BPRM_FCAPS fixes, from Richard Guy Briggs:
The audit subsystem is adding a BPRM_FCAPS record when auditing
setuid application execution (SYSCALL execve). This is not expected
as it was supposed to be limited to when the file system actually
had capabilities in an extended attribute. It lists all
capabilities making the event really ugly to parse what is
happening. The PATH record correctly records the setuid bit and
owner. Suppress the BPRM_FCAPS record on set*id.
TOMOYO:
- Y2038 timestamping fixes"
* 'next-general' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (28 commits)
MAINTAINERS: update the IMA, EVM, trusted-keys, encrypted-keys entries
Smack: Base support for overlayfs
MAINTAINERS: remove David Safford as maintainer for encrypted+trusted keys
tomoyo: fix timestamping for y2038
capabilities: audit log other surprising conditions
capabilities: fix logic for effective root or real root
capabilities: invert logic for clarity
capabilities: remove a layer of conditional logic
capabilities: move audit log decision to function
capabilities: use intuitive names for id changes
capabilities: use root_priveleged inline to clarify logic
capabilities: rename has_cap to has_fcap
capabilities: intuitive names for cap gain status
capabilities: factor out cap_bprm_set_creds privileged root
tpm, tpm_tis: use ARRAY_SIZE() to define TPM_HID_USR_IDX
tpm: fix duplicate inline declaration specifier
tpm: fix type of a local variables in tpm_tis_spi.c
tpm: fix type of a local variable in tpm2_map_command()
tpm: fix type of a local variable in tpm2_get_cc_attrs_tbl()
tpm-dev-common: Reject too short writes
...
BCM7278 features a RNG200 hardware random number generator block, add
support for this chip by matching the chip-specific compatible string
and extending the Kconfig dependencies to allow building on ARCH_BRCMSTB
(base platform for 7278).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The patch for
commit: 5c06273401
Author: Amit Shah <amit.shah@redhat.com>
Date: Sun Jul 27 07:34:01 2014 +0930
virtio: rng: delay hwrng_register() till driver is ready
moved the call to hwrng_register() out of the probe routine into the scan
routine. We need to call hwrng_register() after a suspend/restore cycle
to re-register the device, but the scan function is not invoked for the
restore. Add the call to hwrng_register() to virtio_restore().
Reviewed-by: Liam Merwick <Liam.Merwick@oracle.com>
Signed-off-by: Jim Quigley <Jim.Quigley@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
User is able to select a chosen rng by writing its name to rng_current
but there is no way to reset it without unbinding the rng. Let user
write "" to rng_current and delesect the chosen rng.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
reviewed-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ0WQ6AAoJEHm+PkMAQRiGuloH/3sF4qfBhPuJo8OTf0uCtQ18
4Ux9zZbm81df/Jjz0exAp1Jqk+TvdIS3OXPWcKilvbUBP16hQcsxFTnI/5QF+YcN
87aNr+OCMJzOBK4suN1yhzO46NYHeIizdB0PTZVL1Zsto69Tt31D8VJmgH6oBxAw
Isb/nAkOr31dZ9PI5UEExTIanUt6EywVb0UswA+2rNl3h1UkeasQCpMpK2n6HBhU
kVD7sxEd/CN0MmfhB0HrySSam/BeSpOtzoU9bemOwrU2uu9+5+2rqMe7Gsdj4nX6
3Kk+7FQNktlrhxCZIFN/+CdusOUuDd8r/75d7DnsRK5YvSb0sZzJkfD3Nba68Ms=
=7J2+
-----END PGP SIGNATURE-----
Merge git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux
Merge 4.14-rc3 in order to pick up the new timer_setup function.
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This commit fixes the duplicate inline declaration specifier in
tpm2_rc_value which caused a warning
Signed-off-by: Ruben Roy <rubenroy2005@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Use __le32 type for data in that format.
Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
The local variable 'handle' should have the type __be32 instead of u32.
Fixes: 745b361e98 ("tpm: infrastructure for TPM spaces")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
The local variable 'attrs' should have the type __be32 instead of u32.
Fixes: 58472f5cd4 ("tpm: validate TPM 2.0 commands")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
tpm_transmit() does not offer an explicit interface to indicate the number
of valid bytes in the communication buffer. Instead, it relies on the
commandSize field in the TPM header that is encoded within the buffer.
Therefore, ensure that a) enough data has been written to the buffer, so
that the commandSize field is present and b) the commandSize field does not
announce more data than has been written to the buffer.
This should have been fixed with CVE-2011-1161 long ago, but apparently
a correct version of that patch never made it into the kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The TPM can choose one of two ways to react to the TPM2_SelfTest command.
It can either run all self tests synchronously and then return RC_SUCCESS
once all tests were successful. Or it can choose to run the tests
asynchronously and return RC_TESTING immediately while the self tests still
execute in the background.
The previous implementation apparently was not aware of those possibilities
and attributed RC_TESTING to some prototype chips instead. With this change
the return code of TPM2_SelfTest is interpreted correctly, i.e. the self
test result is polled if and only if RC_TESTING is received.
Unfortunately, the polling cannot be done in the most straightforward way.
If RC_TESTING is received, ideally the code should now poll the
selfTestDone bit in the STS register, as this avoids sending more commands,
that might interrupt self tests executing in the background and thus
prevent them from ever completing. But it cannot be guaranteed that this
bit is correctly implemented for all devices, so the next best thing would
be to use TPM2_GetTestResult to query the test result. But the response to
that command can be very long, and the code currently lacks the
capabilities for efficient unmarshalling, so it is difficult to execute
this command.
Therefore, we simply run the TPM2_SelfTest command in a loop, which should
complete eventually, since we only request the execution of self tests that
have not yet been done.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
In order to avoid delaying the code longer than necessary while still
giving the TPM enough time to execute the self tests asynchronously, start
with a small delay between two polls and increase it each round.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
tpm2_do_selftest is only used during initialization of the TPM to ensure
that the device functions correctly. Therefore, it is sufficient to request
only missing self tests (parameter full_test=0), not a reexecution of all
self tests, as was done before. This allows for a faster execution of this
command.
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The buffers used as tx_buf/rx_buf in a SPI transfer need to be DMA-safe.
This cannot be guaranteed for the buffers passed to tpm_tis_spi_read_bytes
and tpm_tis_spi_write_bytes. Therefore, we need to use our own DMA-safe
buffer and copy the data to/from it.
The buffer needs to be allocated separately, to ensure that it is
cacheline-aligned and not shared with other data, so that DMA can work
correctly.
Fixes: 0edbfea537 ("tpm/tpm_tis_spi: Add support for spi phy")
Cc: stable@vger.kernel.org
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
This patch gets rid of dealing with intermediate flag for start method
and use start method value from ACPI table directly.
For ARM64, the locality is handled by Trust Zone in FW. The layout
does not have crb_regs_head. It is hitting the following line.
dev_warn(dev, FW_BUG "Bad ACPI memory layout");
Current code excludes CRB_FL_ACPI_START for this check. Now since
ARM64 support for TPM CRB is added, CRB_FL_CRB_SMC_START should also be
excluded from this check.
For goIdle and cmdReady where code was excluding CRB_FL_ACPI_START only
(do nothing for ACPI start method), CRB_FL_CRB_SMC_START was also
excluded as ARM64 SMC start method does not have TPM_CRB_CTRL_REQ.
However with special PPT workaround requiring CRB_FL_CRB_START to be
set in addition to CRB_FL_ACPI_START and the addition flag of SMC
start method CRB_FL_CRB_SMC_START, the code has become difficult to
maintain and undrestand. It is better to make code deal with start
method value from ACPI table directly.
Signed-off-by: Jiandi An <anjiandi@codeaurora.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Making cmd_getticks 'const' introduced a couple of harmless warnings:
drivers/char/tpm/tpm_tis_core.c: In function 'probe_itpm':
drivers/char/tpm/tpm_tis_core.c:469:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:477:31: error: passing argument 2 of 'tpm_tis_send_data' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
rc = tpm_tis_send_data(chip, cmd_getticks, len);
drivers/char/tpm/tpm_tis_core.c:255:12: note: expected 'u8 * {aka unsigned char *}' but argument is of type 'const u8 * {aka const unsigned char *}'
static int tpm_tis_send_data(struct tpm_chip *chip, u8 *buf, size_t len)
This changes the related functions to all take 'const' pointers
so that gcc can see this as being correct. I had to slightly
modify the logic around tpm_tis_spi_transfer() for this to work
without introducing ugly casts.
Cc: stable@vger.kernel.org
Fixes: 5e35bd8e06b9 ("tpm_tis: make array cmd_getticks static const to shink object code size")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Don't populate array cmd_getticks on the stack, instead make it static
const. Makes the object code smaller by over 160 bytes:
Before:
text data bss dec hex filename
18813 3152 128 22093 564d drivers/char/tpm/tpm_tis_core.o
After:
text data bss dec hex filename
18554 3248 128 21930 55aa drivers/char/tpm/tpm_tis_core.o
Cc: stable@vger.kernel.org
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The error exit path omits kfree'ing the allocated new_smi, causing a memory
leak. Fix this by kfree'ing new_smi.
Detected by CoverityScan, CID#14582571 ("Resource Leak")
Fixes: 7e030d6dff ("ipmi: Prefer ACPI system interfaces over SMBIOS ones")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
pr_err() messages should terminated with a new-line to avoid
other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Migrated pubek_show to struct tpm_buf and cleaned up its implementation.
Previously the output parameter structure was declared but left
completely unused. Now it is used to refer different fields of the
output. We can move it to tpm-sysfs.c as it does not have any use
outside of that file.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The pointer bmc is being initialized and this initialized value is
never being read, so this is assignment redundant and can be removed.
Cleans up clang warning:
warning: Value stored to 'bmc' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
pr_err() messages should terminated with a new-line to avoid
other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Get rid of all printfs, using dev_xxx() if a device is available,
pr_xxx() otherwise, and format long strings properly.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Rework the DMI probe function to be a generic platform probe, and
then rework the DMI code (and a few other things) to use the more
generic information. This is so other things can declare platform
IPMI devices.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Create a device attribute for everything we show in proc, getting
ready for removing the proc stuff.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Create a device attribute for everything we show in proc, getting
ready for removing the proc stuff.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
