This patch removes the hdac_ext_bus structure. The legacy and
enhanced HDaudio capabilities can be handled in a backward-compatible
way without separate definitions.
Follow-up patches in this series handle the driver definition.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Give topology clients more access to the topology data by passing index,
pcm, link_config and dai_driver to clients. This allows clients to fully
instantiate and track topology objects.
The SOF driver is the first user of these new APIs and needs them to build
component topology driver and FW objects.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl-tplg-interface.h describes firmware format details for Skylake
topology files. It is part of the ABI and should reside in the uapi
directory.
While moving the file, also replace the license boilerplate with
the SPDX License Identifier.
No functional change.
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two commits:
81e9b0a078 ASoC: topology: Give more data to clients via callbacks
28aa6f7779 ASoC: topology: Add callback for DAPM route load/unload
break the build so revert them.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give topology clients more access to the topology data by passing index,
pcm, link_config and dai_driver to clients. This allows clients to fully
instantiate and track topology objects.
The SOF driver is the first user of these new APIs and needs them to build
component topology driver and FW objects.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module id is a property of firmware manifest and can vary across
platforms. So use the uuid to find module id dynamically for bind
params like kpb post bind params.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: "Kp, Jeeja" <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP expects channel map to be sent in the IPC for updown mixer module.
So add ch_map info in updown mixer module config.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP expects length of the coefficient for updown mixer module to be 8.
So fix the max coefficient length and since we are using default values
for coefficient select which is zero, we need not explicitly initialize
it.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since FE dais can come from topology, add dai_load ops
for the dais from topology.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set dma control ipc can be used to set the M/N divider, enable the clks. It
takes different payload for different configuration. So modify the
skl_dsp_set_dma_control API to take the size and node_id as argument.
Signed-off-by: Jaikrishna Nemallapudi <jaikrishnax.nemallapudi@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Copier can support upto 4 output pins. However, only pin 0 is configured
as a part of copier initialization. Configuring rest of pins require the
separate IPC to be sent to fw.
Signed-off-by: Pradeep Tewani <pradeep.d.tewani@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each module's id comes from the topology and gets updated in the
driver. This patch updates the input and output pin connections of
each module by matching the uuid for each module.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A dsp path and the modules in the path can support various pcm
configurations. The list of supported pcm configurations from topology
manifest would be stored and later selected runtime based on the hw
pcm params. For legacy, module data is filled in the 0th index of
resource and interface table.
To accommodate both models, change the relevant structures and populate
them by parsing newly defined tokens. This change is backward compatible
with the existing model where driver computes the resources required by
each dsp module.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The topology manifest would include module common data including resource
and interface table. The resource table consists of resources required by
the dsp module such as buffer size, cycles per second, number of
input/output pins. And, the interface table consists of pcm parameters per
module which can be referenced later.
So define the structures accordingly to represent topology manifest data in
the driver.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this patch, the dma buffer size is fetched from topology binary. This
buffer size is applicable for gateway copier modules.
Now that we can configure DSP dma buffer size, the device can support deep
buffer playback. DSP fetches large buffer and can result fewer wakes,
which helps in power reduction.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
User may prefer to select data from particular mics. A mic-select module
in DSP allows this selection.
Create possible enum controls to allow user to select a combination of
mics to capture data from. Based on the user selection, parameters are
generated and passed to mic-select module during init.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module at the end of DSP pipeline that needs to be connected to a module
in another pipeline are represented as a PGA(leaf node) and in PGA event
handler these modules are bound/unbounded. Modules other than PGA leaf
can be connected directly or via switch to a module in another pipeline.
Example: reference path.
To support the deferred DSP module bind, following changes are done:
o When the path is enabled, the destination module that needs to be
bound may not be initialized. If the module is not initialized, add
these modules in a deferred bind list.
o When the destination module is initialized, check for these modules
in deferred bind list. If found, bind them.
o When the destination module is deleted, Unbind the modules.
o When the source module is deleted, remove the entry from the deferred
bind list.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake driver topology header/driver structure is referenced and used
in SST library which creates circular dependency. Hence the
rearrangement.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For calculating the HDA DMA format, use the max_bps supported by the
DAI caps instead of fixing it to 32/24. For host DMA the Max bps support
is 32, but in case of link DMA, this depends on the codec capability.
So use the sig_bits to define the bps supported by dai.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing the topology manifest info directly to IPC library,
define the manifest info in topology and use this in IPC Library.
This will remove the dependency on topology interface definition with
IPC library.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds helper function to configure the host/link DMA when
the DMA is in decoupled mode.
Next patch adds the usage of this helper routines for configuring
DMA in Mixer event handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To configure Host/Link DMA, additionally link index and format
are required based on the hw params. So added these parameters in
the pipe params and in hw_params the pipe params are updated.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that I2S conflig blob structure is no longer in use, remove it.
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For device opened/closed, we check the D0i3 capability for the device
and invoke skl_tplg_d0i3_get/put, which counts the use case based on the
mode supported.
These counters are then used to decide if the device can enter D0i3 mode
of streaming or non-streaming or no D0i3.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all use cases can support Doi3. Only certain use cases like hot word
detection, deep buffering can support D0i3 based on resource requirement.
So, pass the D0i3 capability for the FE/BE copier using topology. This will
be used to take a decision for D0i3 mode entry/exit.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For D0i3, we need to tell DSP to run the pipelines in LP mode. This
information is kept in topology and passed to driver as an attribute
for pipe.
So add a new tuple for lpmode and program the pipe based on value set.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Post bind parameters of KPB module contains the instance id's of
neighbouring modules in the sink path
Now that module instance ids are generated dynamically we need to update
these parameters as well, so use the table created and update the ids
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver needs to send unique module instance id to firmware while
creating the module and uses this id to communicate with DSP for setting
parameters while audio use case is ongoing.
But, we have upper bound of instance ID. The current IDs are coming from
topology but it doesn't know the upper bound and can't assign unique
id's subject to upper bounds as we can create a big graph but not all
parts running at same time.
This patch adds a 128bit unique id management routines which are built
on top of ffz() for faster implementation. Unfortunately ffz() works on
32bits values, so additional code is added on top of ffz() to create a
128bit unique id.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA control IPC structure wrong config array length,
So corrected the size
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we are moving DSP init to later, at the topology load the
module info is not available.
So set the module id to -1 at init and query at first module
initialization.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP expects the actual length of parameters that is set through
TLV to be passed in large config set, so pass the actual size
received in tlv_control_set() instead of max size.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DSP pipe type can be a pass through or it can be processing pipe.
In case of pass through pipe, it is a single pipeline with both
host and link copier in the same pipeline.
Identify the DSP pipe type if it pass through or not. Pass through
pipe is identified by checking if it has both host and link copier
in the same pipeline.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of XRUN recovery PCM prepare will be called. In this case
Host/Link DMAs are reset and reconfigured, hence the corresponding
FE/BE pipe needs to be reset in order to get to a clean state.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXINZtAAoJECTWi3JdVIfQ+BwH/1eLqMfCSZM9nsDr1QMvOCDP
SO4ZoWqvYplBcS8pYKbJmqtuo8jMxT3VIQF+b5hPAVhgpLwMmy9qeFtatqCQ2WDC
GfCqW8LSKtrzwUwmoRrtHx7vfBLP1/z78F8ORQzwhrplTCBhvPLbUOrV51EFj6tf
Dfo2tW0uxww9iCZduYu4LadOhFOfuw+5shUrJk5A5f975Zbdgyke4CbRnlbDPXLq
d4i7bNfiISkSJiKMpdZFeiOQCd0+uXHh2WkMtVYSGVTA2Kf7d7HtX+JpEFFmaJgJ
8CndjgNJ1ZXtMHl1pMYmNqKJ5mEgmVtbGGJWY4QmQBva0EfQ+vLZt78BG3qvJwk=
=SXH2
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.6-rc5' into asoc-intel
ASoC: Fixes for v4.6
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
To avoid complex string manipulations with UUID in canonical
form, use UUID in binary format.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module needs to be unloaded only when it is loaded successfully.
To fix this, first correct the module state sequence and set module
state to LOADED if module is loaded successfully.
When unloading the module check if module state is not in UNINIT,
then unload it.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SoC has MCLK output which is typically required by codecs.
The MCLK is controlled by DSP FW, so driver can configure that by
sending DMA_CONTROL IPC. The configuration for MCLK is present
in the endpoint blob.
So if block has this configuration, send IPC to DSP for MCLK
configuration. This is done by new function skl_dsp_set_dma_control()
which is invoked by BE prepare.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S port can be connected to multiple BE pipes, get module config
only for the active BE pipe.
This helpers helps to do that and is used in subsequent patches
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a module is ON then we should read the module parameters from
DSP rather than driver cached values
Signed-off-by: Omair M Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module initialization parameter data can be set by
- INIT_INSTANCE IPC by using the default value
- SET_PARAMS immediately after INIT_INSTANCE
- SET_PARAMS data from kcontrol values set
this patch add param type to identify the parameters
has to be sent to DSP.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mic select is a DSP module which is used to select one or many
inputs to form an output. This is useful to select data
selectively from PDM input and hence the name. This module is of
generic module type.
This patch adds support to add and configure Mic select module in
firmware topology.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A module can require extra memory for processing, like audio
algorithms. The memory for these modules needs to be represented
in base module configuration and passed to DSP on init, so add
the memory pages as a field in widget data
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support to configure module parameter during module
initialization or after module init using set module param
required by the DSP firmware sequence.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules has user configurable parameters, which are
required by some modules at module initialization.
To configure the module algorithm parameter during initialization
we add helpers here
Signed-off-by: Divya Prakash <divya1.prakash@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some DSP modules have user configurable parameters. These
parameters are required by modules in the following scenario
- during initialization
- after initialization using set parameter
This patch adds helper routine to set module parameters using
large config set IPC message and removes params to be passed as
init module routine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
