Fix regression introduced by commit 787f9fd232 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather than
BGR:565.
The above commit removes the RGB:555-wiring hack by
removing the no longer used ATMEL_LCDC_WIRING_RGB555 define.
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix regression introduced by commit 787f9fd232 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.
Use SOC-type to determine the pixel layout.
Tested on at91sam9263 and at91sam9g45.
Cc: <stable@vger.kernel.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Display timing's fields have minimum, typical and maximum values. These
can be accessed by using timing_entry_index enum, and
display_timing_get_value() function.
There's no real need for this extra complexity. The values can be
accessed more easily by just using the min/typ/max fields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Instead of having plain defines for the videomode's flags, add an enum
for the flags. This makes the flags clearer to use, as the enum tells
which values can be used with the flags field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Both videomode and display_timing contain flags describing the modes.
These are stored in dmt_flags and data_flags. There's no need to
separate these flags, and having separate fields just makes the flags
more difficult to use.
This patch combines the fields and renames VESA_DMT_* flags to
DISPLAY_FLAGS_*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JMlx
-----END PGP SIGNATURE-----
Merge tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers
Pull fbdev UAPI disintegration from David Howells:
"You'll be glad to here that the end is nigh for the UAPI patches.
Only the fbdev/framebuffer piece remains now that the SCSI stuff has
gone in.
Here are the UAPI disintegration bits for the fbdev drivers. It
appears that Florian hasn't had time to deal with my patch, but back
in December he did say he didn't mind if I pushed it forward."
Yay. No more uapi movement. And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.
* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/video
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
The correct value for VIDCON1_VSTATUS_FRONTPORCH is 3, not 0.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the bit definitions for CSC EQ709 and EQ601. These definitons are
used to control the CSC parameter such as equation 709 and equation 601.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unnecessary brackets and the duplicated VIDTCON2 definition.
Also, header comment is modified, because EXYNOS series is supported and
<mach/regs-fb.h> is not available.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
S3C_FB_MAX_WIN is already defined in 'plat-samsung/include/plat/fb.h'.
So, this definition in 'include/video/samsung_fimd.h' should be removed to
avoid the duplication.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devm_* APIs are device managed and make exit and cleanup code simpler.
While at it also remove some unused labels and fix an error path.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add mmp display subsystem to support Marvell MMP display controllers.
This subsystem contains 4 parts:
--fb folder
--core.c
--hw folder
--panel folder
1. fb folder contains implementation of fb. fb get path and overlay
from common interface and operates on these structures.
2. core.c provides common interface for a hardware abstraction. Major
parts of this interface are:
a) Path: path is a output device connected to a panel or HDMI TV. Main
operations of the path is set/get timing/output color. fb operates
output device through path structure.
b) Ovly: Ovly is a buffer shown on the path.
Ovly describes frame buffer and its source/destination size, offset,
input color, buffer address, z-order, and so on. Each fb device maps
to one overlay.
3. hw folder contains implementation of hardware operations defined by
core.c. It registers paths for fb use.
4. panel folder contains implementation of panels. It's connected to
path. Panel drivers would also regiester panels and linked to path
when probe.
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Signed-off-by: Lisa Du <cldu@marvell.com>
Cc: Guoqing Li <ligq@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for reading display timings from DT into a struct
display_timings. The of_display_timing implementation supports multiple
subnodes. All children are read into an array, that can be queried.
If no native mode is specified, the first subnode will be used.
For cases where the graphics driver knows there can be only one
mode description or where the driver only supports one mode, a helper
function of_get_videomode is added, that gets a struct videomode from DT.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Afzal Mohammed <Afzal@ti.com>
Tested-by: Rob Clark <robclark@gmail.com>
Tested-by: Leela Krishna Amudala <leelakrishna.a@gmail.com>
Add display_timing structure and the according helper functions. This allows
the description of a display via its supported timing parameters.
Also, add helper functions to convert from display timings to a generic videomode
structure.
The struct display_timing specifies all needed parameters to describe the signal
properties of a display in one mode. This includes
- ranges for signals that may have min-, max- and typical values
- single integers for signals that can be on, off or are ignored
- booleans for signals that are either on or off
As a display may support multiple modes like this, a struct display_timings is
added, that holds all given struct display_timing pointers and declares the
native mode of the display.
Although a display may state that a signal can be in a range, it is driven with
fixed values that indicate a videomode. Therefore graphic drivers don't need all
the information of struct display_timing, but would generate a videomode from
the given set of supported signal timings and work with that.
The video subsystems all define their own structs that describe a mode and work
with that (e.g. fb_videomode or drm_display_mode). To slowly replace all those
various structures and allow code reuse across those subsystems, add struct
videomode as a generic description.
This patch only includes the most basic fields in struct videomode. All missing
fields that are needed to have a really generic video mode description can be
added at a later stage.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Afzal Mohammed <Afzal@ti.com>
Tested-by: Rob Clark <robclark@gmail.com>
Tested-by: Leela Krishna Amudala <leelakrishna.a@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
The i2c handling in tfp410 driver, which handles converting parallel RGB
to DVI, was changed in 958f2717b8
(OMAPDSS: TFP410: pdata rewrite). The patch changed what value the
driver considers as invalid/undefined. Before the patch, 0 was the
invalid value, but as 0 is a valid bus number, the patch changed this to
-1.
However, the fact was missed that many board files do not define the bus
number at all, thus it's left to 0. This causes the driver to fail to
get the i2c bus, exiting from the driver's probe with an error, meaning
that the DVI output does not work for those boards.
This patch fixes the issue by changing the i2c_bus number field in the
driver's platform data from u16 to int, and setting the bus number to -1
in the board files for the boards that did not define the bus. The
exception is devkit8000, for which the bus is set to 1, which is the
correct bus for that board.
The bug exists in v3.5+ kernels.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Thomas Weber <thomas@tomweber.eu>
Cc: Thomas Weber <thomas@tomweber.eu>
Cc: <stable@vger.kernel.org> # v3.5+
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAPDSS changes for 3.8, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming common
display framework
* tag 'omapdss-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (140 commits)
OMAPDSS: fix TV-out issue with DSI PLL
Revert "OMAPFB: simplify locking"
OMAPFB: remove silly loop in fb2display()
OMAPFB: fix error handling in omapfb_find_best_mode()
OMAPFB: use devm_kzalloc to allocate omapfb2_device
OMAPDSS: DISPC: remove dispc fck uses
OMAPDSS: DISPC: get dss clock rate from dss driver
OMAPDSS: use omapdss_compat_init() in other drivers
OMAPDSS: export dispc functions
OMAPDSS: export dss_feat functions
OMAPDSS: export dss_mgr_ops functions
OMAPDSS: separate compat files in the Makefile
OMAPDSS: move display sysfs init to compat layer
OMAPDSS: DPI: use dispc's check_timings
OMAPDSS: DISPC: add dispc_ovl_check()
OMAPDSS: move irq handling to dispc-compat
OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
OMAPDSS: move blocking mgr enable/disable to compat layer
OMAPDSS: manage framedone irq with mgr ops
OMAPDSS: add manager ops
...
We have two functions to wait for a dispc interrupt:
int omap_dispc_wait_for_irq_timeout(u32 irqmask, unsigned long timeout);
int omap_dispc_wait_for_irq_interruptible_timeout(u32 irqmask,
Of these, the former is not used at all, and can be removed. The latter
is only used by the compat layer, and can be moved to the compat layer
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add two new exported functions, omapdss_compat_init and
omapdss_compat_uninit, which are to be used by omapfb, omap_vout to
enable compatibility mode for omapdss. The functions are called by
omapdss internally for now, and moved to other drivers later.
The compatibility mode is implemented fully in the following patches.
For now, enabling compat mode only sets up the private data in apply.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Samsung Framebuffer changes for the 3.8 merge window.
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
* 'samsung-fb-next' of git://github.com/jingoo/linux:
video: s3c-fb: fix red offset and length for ARGB232 format
video: s3c-fb: return an error when bpp is invalid
video: s3c-fb: add "drop through" comment
video: s3c-fb: use dev_get_drvdata() instead of platform_get_drvdata()
video: s3c-fb: use FIMD_V8_VIDTCON0 for EXYNOS5 FIMD
video: s3c-fb: fix help message for FB_S3C_DEBUG_REGWRITE
video: s3c-fb: fix typo in comment
video: s3c-fb: add the bit definitions for VIDCON0_VIDOUT_WB
video: s3c-fb: move the bit definitions for DITHMODE register
video: s3c-fb: move the bit definitions for WINxMAP and WPALCON register
video: s3c-fb: move the bit definitions for VIDINTCON0 register
video: s3c-fb: move the address definition for VIDOSD register
video: s3c-fb: move the address definitions for VIDTCON registers
video: s3c-fb: clean the bit definition for WINCON register
Configure below LCDC configurations to optimal values, also have an
option configure these optional parameters for platform.
1) AC bias configuration: Required only for passive panels
2) Dma_burst_size:
3) FIFO_DMA_DELAY:
4) FIFO threshold: Does not apply for da830 LCDC.
Patch is verified for 16bpp and 24bpp configurations on da830, da850 and
am335x EVMs.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adopt fb_videomode data instead of defining driver private
structure to hold panel information. This is the way standard FB
drivers maintain the panel information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds the bit definitions for VIDCON0_VIDOUT_WB.
These definitions are used to support writeback for RGB and
i80 interface. Also, output format of writeback is YUV444.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
The bit definitions for DITHMODE registers are moved according to
address order. Also, the bit definition of VIDCON1_FSTATUS_EVEN
is moved.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch cleans the bit definition for WINCON register.
The bit definition for WINCON1 and WINCON2 is removed, because
it is not used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
The channel field stores the LCDC channel corresponding to the MIPI-DSI
transmitter. The information is currently obtained through the lcd_chan
field that will be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Export dss_get_def_display_name() with the name of
omapdss_get_def_display_name() so that omapfb can use it after the next
patch which moves default display handling to omapfb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The output drivers get the omapdss hw version from the platform data for
their respective output device. This doesn't work with DT, as there's no
platform data for them.
Add a new function, omapdss_get_version(), which returns the dss version
from the core device, which will have platform data on DT also. The
function is exported so that users of omapdss can also use it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The panel drivers contain enable, disable, suspend and resume calls.
The suspend and resume are effectively identical to disable and enable.
This patch removes panel suspend and enable code from omapdss and the
panel drivers, and replaces their use with enable and disable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
acbi and acb fields were meant for passive matrix panels which omapdss
doesn't support any longer. Remove these fields from omap_dss_device
struct.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add an exported function omap_vrfb_supported() which returns true if the
vrfb driver has been loaded succesfully. This can be used to decide if
VRFB can be used or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that vrfb driver is not omap dependent anymore, we can move vrfb.h
from arch/arm/plat-omap/include/plat to include/video/omapvrfb.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Add new enum, omapdss_version, that is used to tell which DSS hardware
version the SoC has. This enum is initialized during platform init, and
passed in the platform data to omapdss driver.
Note that the versions are not "continuous", that is, you cannot check
if the version is less or greater than something, but you need to check
for exact version match. In other words, this is invalid:
/* test if DSS is 3630 or earlier */
if (ver <= OMAPDSS_VER_OMAP3630)
...
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=EJUS
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
Notable changes:
* Basic writeback support for DISPC level. Writeback is not yet usable, though,
as we need higher level code to actually expose the writeback feature to
userspace.
* Rewriting the omapdss output drivers. We're trying to remove the hard links
between the omapdss and the panels, and this rewrite work moves us closer to
that goal.
* Cleanup and restructuring patches that have been made while working on device
tree support for omapdss. Device tree support is still some way ahead, but
these patches are good cleanups in themselves.
* Basic OMAP5 DSS support for DPI and DSI outputs.
* Workaround for the problem that GFX overlay's fifo is too small for high
resolution scenarios, causing underflows.
* Cleanups that remove dependencies to omap platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lcyJ
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.7' of git://gitorious.org/linux-omap-dss2/linux into fbdev-next
Omapdss driver changes for the 3.7 merge window.
Notable changes:
* Basic writeback support for DISPC level. Writeback is not yet usable, though,
as we need higher level code to actually expose the writeback feature to
userspace.
* Rewriting the omapdss output drivers. We're trying to remove the hard links
between the omapdss and the panels, and this rewrite work moves us closer to
that goal.
* Cleanup and restructuring patches that have been made while working on device
tree support for omapdss. Device tree support is still some way ahead, but
these patches are good cleanups in themselves.
* Basic OMAP5 DSS support for DPI and DSI outputs.
* Workaround for the problem that GFX overlay's fifo is too small for high
resolution scenarios, causing underflows.
* Cleanups that remove dependencies to omap platform code.
The current kernel does not fit in the CEIVA ROM. Also, some functional
has already been removed due migrate from 2.6 to 3.0, and it seems that
no one uses this platform. So, remove support for this board and modules
specific only to this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Create struct omap_dss_writeback_info, this is similar to omap_overlay_info,
the major difference is that there is no parameter which describes the input
size to writeback, this is because this is always fixed, and decided by the
connected overlay or overlay manager. One more difference is that screen_width
is renamed to buf_width, to give the value of stride the writeback buffer has.
Call dispc_ovl_setup_common() through dispc_wb_setup() to configure overlay-like
parameters. The parameters in dispc_ovl_setup_common() which do not hold for
writeback are filled passed as zeroes or false, the code takes care of not
configuring them as they won't possess the needed overlay caps.
Signed-off-by: Archit Taneja <archit@ti.com>
Add position and replication as overlay caps, and pass overlay caps as an
argument to the corresponding functions. Adding position and replication to
overlay caps seems a bit unnecessary, but it allows us to use the
corresponding functions for writeback too.
These caps will be set for all overlays, but not for writeback. This is done
so writeback can reuse dispc_ovl_setup() to the maximum.
Signed-off-by: Archit Taneja <archit@ti.com>
Now that an omap_dss_output can be used to link between managers and devices, we
can remove the old way of setting manager and device links. This involves
removing the device and manager pointers from omap_overlay_manager and
omap_dss_device respectively, and removing the set_device/unset_device ops from
omap_overlay_manager.
Signed-off-by: Archit Taneja <archit@ti.com>
With the introduction of output entities, managers will now connect to outputs.
Create helper ops for overlays and managers named get_device. This will abstract
away the information on how to get the device from an overlay or an overlay
manager. The get_device ops currently retrieve the output via a
ovl->manager->device reference. This will be later replaced by
ovl->manager->output->device references.
Signed-off-by: Archit Taneja <archit@ti.com>
Add set_output/unset_output ops for overlay managers, these form links between
managers and outputs. Create a function in dss features which tell all the
output instances that connect to a manager, use it when a manager tries to set
an output. Add a constraint of not unsetting an output when the manager is
enabled.
Keep the omap_dss_device pointer and set/unset_device ops in overlay_manager for
now to not break things. Keep the dss feature function get_supported_displays
as it's used in some places. These will be removed later.
Signed-off-by: Archit Taneja <archit@ti.com>
An output entity represented by the struct omap_dss_output connects to a
omap_dss_device entity. Add functions to set or unset an output's device. This
is similar to how managers and devices were connected previously. An output can
connect to a device without being connected to a manager. However, the output
needs to eventually connect to a manager so that the connected panel can be
enabled.
Keep the omap_overlay_manager pointer in omap_dss_device for now to prevent
breaking things. This will be removed later when outputs are supported
completely.
Signed-off-by: Archit Taneja <archit@ti.com>
The current OMAPDSS design contains 3 software entities: Overlays, Managers and
Devices. These map to pipelines, overlay managers and the panels respectively in
hardware. One or more overlays connect to a manager to represent a composition,
the manager connects to a device(generally a display) to display the content.
The part of DSS hardware which isn't represented by any of the above entities
are interfaces/outputs that connect to an overlay manager, i.e blocks like DSI,
HDMI, VENC and so on. Currently, an overlay manager directly connects to the
display, and the output to which it is actually connected is ignored. The panel
driver of the display is responsible of calling output specific functions to
configure the output.
Adding outputs as a new software entity gives us the following benefits:
- Have exact information on the possible connections between managers and
outputs: A manager can't connect to each and every output, there only limited
hardware links between a manager's video port and some of the outputs.
- Remove hacks related to connecting managers and devices: Currently, default
links between managers and devices are set in a not so clean way. Matching is
done via comparing the device type, and the display types supported by the
manager. This isn't sufficient to establish all the possible links between
managers, outputs and devices in hardware.
- Make panel drivers more generic: The DSS panel drivers currently call
interface/output specific functions to configure the hardware IP. When making
these calls, the driver isn't actually aware of the underlying output. The
output driver extracts information from the panel's omap_dss_device pointer
to figure out which interface it is connected to, and then configures the
corresponding output block. An example of this is when a DSI panel calls
dsi functions, the dsi driver figures out whether the panel is connected
to DSI1 or DSI2. This isn't correct, and having output as entities will
give the panel driver the exact information on which output to configure.
Having outputs also gives the opportunity to make panel drivers generic
across different platforms/SoCs, this is achieved as omap specific output
calls can be replaced by ops of a particular output type.
- Have more complex connections between managers, outputs and devices: OMAPDSS
currently doesn't support use cases like 2 outputs connect to a single
device. This can be achieved by extending properties of outputs to connect to
more managers or devices.
- Represent writeback as an output: The writeback pipeline fits well in OMAPDSS
as compared to overlays, managers or devices.
Add a new struct to represent outputs. An output struct holds pointers to the
manager and device structs to which it is connected. Add functions which can
register/unregister an output, or look for one. Create an enum which represent
each output instance.
Signed-off-by: Archit Taneja <archit@ti.com>
OMAP4's GFX overlay has smaller fifo than the rest of the overlays
(including writeback "overlay"). This seems to be the reason for
underflows in some more demanding scenarios.
We can avoid the problems by using the WB fifo for GFX overlay, and vice
versa. WB usage is not supported yet, but when it will, it should
perform just fine with smaller fifo as there are no hard realtime
constraints with WB.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently the way to configure clocks related to DSI (both DSI and DISPC
clocks) happens via omapdss platform data. The reason for this is that
configuring the DSS clocks is a very complex problem, and it's
impossible for the SW to know requirements about things like
interference.
However, for general cases it should be fine to calculate the dividers
for clocks in the SW. The calculated clocks are probably not perfect,
but should work.
This patch adds support to calculate the dividers when using DSI command
mode panels. The panel gives the required DDR clock rate and LP clock
rate, and the DSI driver configures itself and DISPC accordingly.
This patch is somewhat ugly, though. The code does its job by modifying
the platform data where the clock dividers would be if the board file
gave them. This is not how it's going to be in the future, but allows us
to have quite simple patch and keep the backward compatibility.
It also allows the developer to still give the exact dividers from the
board file when there's need for that, as long as the panel driver does
not override them.
There are also other areas for improvement. For example, it would be
better if the panel driver could ask for a DSI clock in a certain range,
as, at least command mode panels, the panel can work fine with many
different clock speeds.
While the patch is not perfect, it allows us to remove the hardcoded
clock dividers from the board file, making it easier to bring up a new
panel and to use device tree from omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently manage HDMI GPIOs in the board files via
platform_enable/disable calls. This won't work with device tree, and in
any case the correct place to manage the GPIOs is in the HDMI driver.
This patch moves the handling of the GPIOs to the HDMI driver. The GPIO
handling is moved to the common hdmi.c file, and this probably needs to
be revisited when adding OMAP5 HDMI support to see if the GPIO handling
needs to be moved to IP specific files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The DISPC_IRQ bit definitions pertaining to channel LCD3 as DISPC_IRQ_VSYNC3,
DISPC_IRQ_SYNC_LOST3, DISPC_IRQ_ACBIAS_COUNT_STAT3 AND DISPC_IRQ_FRAMEDONE3
which were incorrectly set in previous LCD3 patches have been corrected here.
Reported-by: Mark Tyler <mark.tyler@ti.com>
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The RFBI driver currently relies on the omap_dss_device struct to receive the
rfbi specific timings requested by the panel driver. This makes the RFBI
interface driver dependent on the omap_dss_device struct.
Make the RFBI driver data maintain it's own rfbi specific timings field. The
panel driver is expected to call omapdss_rfbi_set_interface_timings() to
configure the rfbi timings before the interface is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the omap_dss_device struct to receive the
video mode timings requested by the panel driver. This makes the DSI interface
driver dependent on the omap_dss_device struct.
Make the DSI driver data maintain it's own video mode timings field. The panel
driver is expected to call omapdss_dsi_set_videomode_timings() to configure the
video mode timings before the interface is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The struct omap_dss_dsi_videomode_data holds fields which need to be configured
for DSI to operate in video mode. Rename the struct to dsi_videomode_timings.
One reason to do this is because most of the fields in the struct are timings
related. The other reason is to create a generic op for output specific
timings. This generic op can be considered as a way to set custom or private
timings for the output.
In the case of OMAP, DSI and RFBI require some more timings apart from the
relgular DISPC timings. The structs omap_dss_videomode_timings and rfbi_timings
can be considered as these output specific timings respectively.
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the omap_dss_device struct to know the mode
of operation of the DSI protocol(command or video mode). This makes the DSI
interface driver dependent on the omap_dss_device struct.
Make the DSI driver data maintain it's own operation mode field. The panel
driver is expected to call omapdss_dsi_set_operation_mode() before the interface
is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The SDI driver currently relies on the omap_dss_device struct to configure the
number of data pairs as specified by the panel. This makes the SDI interface
driver dependent on the omap_dss_device struct.
Make the SDI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_sdi_set_datapairs() before enabling the interface.
Even though we configure the number of data pairs here, this function would be
finally mapped to a generic interface op called set_data_lines. The datapairs
argument type has been changed from u8 to int at some places to be in sync with
the 'set_data_lines' ops of other interfaces.
Signed-off-by: Archit Taneja <archit@ti.com>
The DPI driver currently relies on the omap_dss_device struct to configure the
number of data lines as specified by the panel. This makes the DPI interface
driver dependent on the omap_dss_device struct.
Make the DPI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_dpi_set_data_lines() before enabling the interface.
Signed-off-by: Archit Taneja <archit@ti.com>
The RFBI driver currently relies on the omap_dss_device struct to configure the
number of data lines as specified by the panel. This makes the RFBI interface
driver dependent on the omap_dss_device struct.
Make the RFBI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_rfbi_set_data_lines() to configure the pixel format
before enabling the interface or calling omap_rfbi_configure().
Signed-off-by: Archit Taneja <archit@ti.com>
The RFBI driver currently relies on the omap_dss_device struct to receive the
desired pixel size of the panel. This makes the RFBI interface driver dependent
on the omap_dss_device struct.
Make the RFBI driver data maintain it's own pixel format field. A panel driver
is expected to call omapdss_rfbi_set_pixel_size() to configure the pixel format
before enabling the interface or calling omap_rfbi_configure().
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the omap_dss_device struct to receive the
desired pixel format of the panel. This makes the DSI interface driver dependent
on the omap_dss_device struct.
Make the DSI driver data maintain it's own pixel format field. The panel driver
is expected to call omapdss_dsi_set_pixel_format() to configure the pixel format
before the interface is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
RFBI drivers requires configuration of the update area. Since we don't support
partial updates, the size to be configures is the panel size itself.
Add a timings field in RFBI's driver data. Apart from x_res and y_res, all the
other fields are configured to an initial value when RFBI is enabled. A panel
driver is expected to call omapdss_rfbi_set_size() configure the size of the
panel.
Signed-off-by: Archit Taneja <archit@ti.com>
Partial update suppport was removed from DISPC and DSI sometime back. The RFBI
driver still tries to support partial update without the underlying support in
DISPC.
Remove partial update support from RFBI, only support updates which span acros
the whole panel size. This also helps in DSI and RFBI having similar update
ops.
Signed-off-by: Archit Taneja <archit@ti.com>
Create function omapdss_sdi_set_timings(). Configuring new timings is done the
same way as before, SDI is disabled, and re-enabled with the new timings in
dssdev. This just moves the code from the panel drivers to the SDI driver.
The panel drivers shouldn't be aware of how SDI manages to configure a new set
of timings. This should be taken care of by the SDI driver itself.
Signed-off-by: Archit Taneja <archit@ti.com>
DSI command mode panels don't need to configure a full set of timings to
configure DSI, they only require the width and the height of the panel in
pixels.
Use omapdss_dsi_set_size for command mode panels, omapdss_dsi_set_timings is
meant for video mode panels. When performing rotation via chaning the address
mode of the panel, we would need to swap width and height when doing 90 or 270
rotation. Make sure that omapdss_dsi_set_size() makes the new width and height
visible to DSI.
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the timings in omap_dss_device struct to
configure the DISPC and DSI blocks accordingly. This makes the DSI interface
driver dependent on the omap_dss_device struct.
Make the DSI driver data maintain it's own timings field. A DSI video mode panel
driver is expected to call omapdss_dsi_set_timings() to set these timings before
the panel is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The DPI driver currently relies on the timings in omap_dss_device struct to
configure the DISPC accordingly. This makes the DPI interface driver dependent
on the omap_dss_device struct.
Make the DPI driver data maintain it's own timings field. The panel driver is
expected to call dpi_set_timings()(renamed to omapdss_dpi_set_timings) to set
these timings before the panel is enabled.
In the set_timings() op, we still ensure that the omap_dss_device timings
(dssdev->panel.timings) are configured. This will later be configured only by
the DPI panel drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
FIMD version 8 has VIDTCON and VIDCON registers at different offsets
from the previous versions. Hence, adding the macros.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves the contents from regs-fb-v4.h and regs-fb.h to
include/video/samsung_fimd.h. Also updates the header inclusion in
machine files and driver files accordingly.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Patch works around the below silicon errata:
During LCDC initialization, there is the potential for a FIFO
underflow condition to occur. A FIFO underflow condition
occurs when the input FIFO is completely empty and the LCDC
raster controller logic that drives data to the output pins
attempts to fetch data from the FIFO. When a FIFO underflow
condition occurs, incorrect data will be driven out on the
LCDC data pins.
Software should poll the FUF bit field in the LCD_STAT register
to check if an error condition has occurred or service the
interrupt if FUF_EN is enabled when FUF occurs. If the FUF bit
field has been set to 1, this will indicate an underflow
condition has occurred and then the software should execute a
reset of the LCDC via the LPSC.
This problem may occur if the LCDC FIFO threshold size
(LCDDMA_CTRL[TH_FIFO_READY]) is left at its default value after
reset. Increasing the FIFO threshold size will reduce or
eliminate underflows. Setting the threshold size to 256 double
words or larger is recommended.
Above issue is described in section 2.1.3 of silicon errata
http://www.ti.com/lit/er/sprz313e/sprz313e.pdf
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The API can be used to allocate and free MERAM blocks directly, without
going through ICBs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
There's no reason to use abstract operation pointers to implement the
MERAM API. Replace them by direct function calls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The MERAM operations meram_register, meram_unregister and meram_update
handle LCDC cache. In preparation for "raw" MERAM allocation, rename
them to more appropriate names.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
For DSI operation in videomode, DISPC logic levels for the signals HSYNC, VSYNC
and DE need to be specified to DSI via the fields VP_HSYNC_POL, VP_VSYNC_POL and
VP_DE_POL in DSI_CTRL registers.
This information is completely internal to DSS as logic levels for the above
signals hold no meaning on the DSI bus. Hence a DSI panel driver should be
totally oblivious of these fields.
Fix the logic levels/polarities in the DISPC and DSI registers to a default
value. This is done by overriding these fields in omap_video_timings struct
filled by the panel driver for DISPC, and use the equivalent default values
when programming DSI_CTRL registers. Also, remove the redundant polarity related
fields in omap_dss_dsi_videomode_data.
Signed-off-by: Archit Taneja <archit@ti.com>
Add a parameter called interlace which tells whether the timings are in
interlaced or progressive mode. This aligns the omap_video_timings struct with
the Xorg modeline configuration.
It also removes the hack needed to write to divide the manager height by 2 if
the connected interface is VENC.
Signed-off-by: Archit Taneja <archit@ti.com>
omap_panel_config contains fields which are finally written to DISPC_POL_FREQo
registers. These are now held by omap_video_timings and are set when the manager
timings are applied.
Remove the omap_panel_config enum, and remove all it's references from panel or
interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Some panel timing related fields are contained in omap_panel_config in the form
of flags. The fields are:
- Hsync logic level
- Vsync logic level
- Data driven on rising/falling edge of pixel clock
- Output enable/Data enable logic level
- HSYNC/VSYNC driven on rising/falling edge of pixel clock
Out of these parameters, Hsync and Vsync logic levels are a part of the timings
in the Xorg modeline configuration. So it makes sense to move the to
omap_video_timings. The rest aren't a part of modeline, but it still makes
sense to move these since they are related to panel timings.
These fields stored in omap_panel_config in dssdev are configured for LCD
panels, and the corresponding LCD managers in the DISPC_POL_FREQo registers.
Add the above fields in omap_video_timings. Represent their state via new enums.
Add these parameters to the omap_video_timings instances in the panel drivers.
Keep the corresponding IVS, IHS, IPC, IEO, RF and ONOFF flags in
omap_panel_config for now. The struct will be removed later.
Signed-off-by: Archit Taneja <archit@ti.com>
Remove omap_lcd_display_type enum
The enum omap_lcd_display_type is used to configure the lcd display type in
DISPC. Remove this enum and always set display type to TFT by creating function
dss_mgr_set_lcd_type_tft().
Signed-off-by: Archit Taneja <archit@ti.com>
Remove OMAP_DSS_LCD_TFT as a omap_panel_config flag.
We don't support passive matrix displays any more. Remove this flag from all the
panel drivers.
Force the display_type to OMAP_DSS_LCD_DISPLAY_TFT in the interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
The support for LCD3 manager has been added into the manager module. LCD3 panel
has registers as DISPC_CONTROL3 and DISPC_CONFIG3 just like those in LCD and
LCD2 panels. These registers control the Display Controller (DISPC) module for
LCD3 output. The three LCDs support Display Serial Interface (DSI), Remote Frame
Buffer Interface (RFBI) and Parallel CMOS Output Interface (DPI). These LCDs can
be connected through parallel output interface using DISPC and RFBI or DPI. For
serial interface DSS uses DSI.
The LCD3 panel, just like LCD and LCD2 panels, has a clock switch in DSS_CTRL
register which has been enabled. The clock switch chooses between DSS_CLK and
DPLL_DSI1_C_CLK1 as source for LCD3_CLK. New IRQs as DISPC_IRQ_VSYNC3,
DISPC_IRQ_FRAMEDONE3, DISPC_IRQ_ACBIAS_COUNT_STAT3 and DISPC_IRQ_SYNC_LOST3 have
been added specific to the new manager.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5 Display Subsystem (DSS) architecture comes with a additional LCD3 channel
with its own dedicated overlay manager. The current patch adds LCD3 channel and
basic register support for LCD3 channel. It adds register addresses for various
Display Controller (DISPC) registers like DISPC_DEFAULT_COLOR, DISPC_TIMING_H,
DISPC_DIVISORo, etc.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have two almost the same enums: omap_channel and
omap_dss_overlay_managers. omap_channel is used almost everywhere, and
omap_channel assigns explicit values to the enum values which are needed
for proper operation.
omap_dss_overlay_managers is only used in one place, so it's easy to
remove it, which is what this patch does.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It includes:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)
iQIcBAABAgAGBQJPyAhmAAoJECSVL5KnPj1PBcoQAIWftuoXo3sk94f5jKcV4Ucx
MthEc5iEpMVs8xaEruHHNHXWv8ic0x/PfdC2xrpKOEbNXQcNPlb/QE2xWmBRxmT1
ucDyu10HJ36jKcwcK4ra5IQwOW+GtbTBEoBZT+WNAjxHZtJmxzjQGM4C12zVQpdJ
+qV2RP93JmsJoVBL9aKVAg1Ko135LLfD8TcKd+z8TmgFnLfSwKhfl7Jtd2xXwyvz
/hmW3kJUEnD8E5wuj+/g8sKJhQkGalEiITTqG2j2vJyFgxHSqyLSw8BBixrFW1uT
B9VnZsHF35ccCo+96UZRH4QsGJTx08+rea/qsv8IMSGczyRp5ey1ufjL+CzKiiIN
FWfex6fY0HHqZGAopQhjag54e914SIbSxdBwWS/iRrtVt3e9d03BzkhYs4rXl4Ey
CTC5obzWNTbQ6hLEjgWfVKkKcrF56BnRn3zGPgCTKGp2NK3vODdBkt/EmzUFvCWR
CcyQhh+PvZzEWp3XsdOGossYs/0aP4bO+7XPGJxZaa3+WVcRaZwAG/uZvJXXBfnp
DGRFy4wPsTTwKYIx4+t/KrsLtNVKioSMS5GEtuM1YEb8pA7mkUIkqwJv1I261h58
heTr6vWUsviUqHlKALJ+1CdwWGr3CtktCZssGsSUri61nm8CvlSRn2Nr2aJ/L3RN
AkemC/33RE5X/+lfkdMx
=tmIU
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- driver for AUO-K1900 and AUO-K1901 epaper controller
- large updates for OMAP (e.g. decouple HDMI audio and video)
- some updates for Exynos and SH Mobile
- various other small fixes and cleanups
* tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits)
video: bfin_adv7393fb: Fix cleanup code
video: exynos_dp: reduce delay time when configuring video setting
video: exynos_dp: move sw reset prioir to enabling sw defined function
video: exynos_dp: use devm_ functions
fb: handle NULL pointers in framebuffer release
OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request
OMAPDSS: Apply VENC timings even if panel is disabled
OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC
OMAPDSS: DISPC: Support rotation through TILER
OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n
OMAPFB: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: remove compiler warnings when CONFIG_BUG=n
OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv
OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays
OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods
OMAPDSS: DISPC: Update Accumulator configuration for chroma plane
drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers
video: exynos mipi dsi: support reverse panel type
video: exynos mipi dsi: Properly interpret the interrupt source flags
video: exynos mipi dsi: Avoid races in probe()
...
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=I8Se
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.5' of git://github.com/tomba/linux into fbdev-next
Omapdss driver changes for 3.5 merge window.
Lots of normal development commits, but perhaps most notable changes are:
* HDMI rework to properly decouple the HDMI audio part from the HDMI video part.
* Restructure omapdss core driver so that it's possible to implement device
tree support. This included changing how platform data is passed to the
drivers, changing display device registration and improving the panel driver's
ability to configure the underlying video output interface.
* Basic support for DSI packet interleaving
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
TILER is a block in OMAP4's DMM which lets DSS fetch frames in a rotated manner.
Physical memory can be mapped to a portion of OMAP's system address space called
TILER address space. The TILER address space is split into 8 views. Each view
represents a rotated or mirrored form of the mapped physical memory. When a
DISPC overlay's base address is programmed to one of these views, the TILER
fetches the pixels according to the orientation of the view. A view is further
split into 4 containers, each container holds elements of a particular size.
Rotation can be achieved at the granularity of elements in the container. For
more information on TILER, refer to the Memory Subsytem section in OMAP4 TRM.
Rotation type TILER has been added which is used to exploit the capabilities of
these 8 views for performing various rotations.
When fetching from addresses mapped to TILER space, the DISPC DMA can fetch
pixels in either 1D or 2D bursts. The fetch depends on which TILER container we
are accessing. Accessing 8, 16 and 32 bit sized containers requires 2D bursts,
and page mode sized containers require 1D bursts.
The DSS2 user is expected to provide the Tiler address of the view that it is
interested in. This is passed to the paddr and p_uv_addr parameters in
omap_overlay_info. It is also expected to provide the stride value based on the
view's orientation and container type, this should be passed to the screen_width
parameter of omap_overlay_info. In calc_tiler_rotation_offset screen_width is
used to calculate the required row_inc for DISPC. x_predecim and y_predecim are
also used to calculate row_inc and pix_inc thereby adding predecimation support
for TILER.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Latest SuperH HDMI uses not only HDMI Core Register (HTOP0)
but also HDMI Control Register (HTOP1).
This patch adds HDMI Control Register support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Latest SuperH HDMI allows 32bit access only.
But the data is 8bit. So, we can keep compatibility by switching 8/32 bit access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
There exist several display technologies and standards that support audio as
well. Hence, it is relevant to update the DSS device driver to provide an audio
interface that may be used by an audio driver or any other driver interested in
the functionality.
The audio_enable function is intended to prepare the relevant
IP for playback (e.g., enabling an audio FIFO, taking in/out of reset
some IP, enabling companion chips, etc). It is intended to be called before
audio_start. The audio_disable function performs the reverse operation and is
intended to be called after audio_stop.
While a given DSS device driver may support audio, it is possible that for
certain configurations audio is not supported (e.g., an HDMI display using a
VESA video timing). The audio_supported function is intended to query whether
the current configuration of the display supports audio.
The audio_config function is intended to configure all the relevant audio
parameters of the display. In order to make the function independent of any
specific DSS device driver, a struct omap_dss_audio is defined. Its purpose
is to contain all the required parameters for audio configuration. At the
moment, such structure contains pointers to IEC-60958 channel status word and
CEA-861 audio infoframe structures. This should be enough to support HDMI and
DisplayPort, as both are based on CEA-861 and IEC-60958. The omap_dss_audio
structure may be extended in the future if required.
The audio_enable/disable, audio_config and audio_supported functions could be
implemented as functions that may sleep. Hence, they should not be called
while holding a spinlock or a readlock.
The audio_start/audio_stop function is intended to effectively start/stop audio
playback after the configuration has taken place. These functions are designed
to be used in an atomic context. Hence, audio_start should return quickly and be
called only after all the needed resources for audio playback (audio FIFOs,
DMA channels, companion chips, etc) have been enabled to begin data transfers.
audio_stop is designed to only stop the audio transfers. The resources used
for playback are released using audio_disable.
A new enum omap_dss_audio_state is introduced to help the implementations of
the interface to keep track of the audio state. The initial state is _DISABLED;
then, the state transitions to _CONFIGURED, and then, when it is ready to
play audio, to _ENABLED. The state _PLAYING is used when the audio is being
rendered.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
The omapdss pdata handling is a mess. This is more evident when trying
to use device tree for DSS, as we don't have platform data anymore in
that case. This patch cleans the pdata handling by:
- Remove struct omap_display_platform_data. It was used just as a
wrapper for struct omap_dss_board_info.
- Pass the platform data only to omapdss device. The drivers for omap
dss hwmods do not need the platform data. This should also work better
for DT, as we can create omapdss device programmatically in generic omap
boot code, and thus we can pass the pdata to it.
- Create dss functions for get_ctx_loss_count and dsi_enable/disable_pads
that the dss hwmod drivers can call.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Conflicts:
drivers/video/omap2/displays/panel-taal.c
Merge OMAP DSS related board file changes. The branch will also be
merged through linux-omap tree to solve conflicts.
In preparation for device tree, this patch changes how the DSI pins are
configured. The current configuration method is only doable with board
files and the configuration data is OMAP specific.
This patch moves the configuration data to the panel's platform data,
and the data can easily be given via DT in the future. The configuration
data format is also changed to a generic one which should be suitable
for all platforms.
The new format is an array of pin numbers, where the array items start
from clock + and -, then data1 + and -, and so on. For example:
{
0, // pin num for clock lane +
1, // pin num for clock lane -
2, // pin num for data1 lane +
3, // pin num for data1 lane -
...
}
The pin numbers are translated by the DSI driver and used to configure
the hardware appropriately.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the tfp410 driver has been renamed in the code, this patch
finishes the renaming by renaming the files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 DPI-to-DVI chip was named quite badly as "DVI
panel driver". This patch renames the code to use tfp410 name for the
driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Now that the panel-dvi driver handles the PD (power-down) GPIO, we can
remove the custom PD handling from the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The driver for the TFP410 chip should handle the power-down signal of
the chip, instead of the current way of handling it in the board files.
This patch adds power_down_gpio into the device's platform data, and
adds the necessary code in the driver to request and handle the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch fixes max loop count in EQ(Channel Equalization) sequence
of link training. According to DP(displayport) specification,
the max loop count in this sequence should be 5.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The AUO-K190X controllers share a very similar set of commands and
can therefore also share most of the driver code.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
With this we can eliminate some duplicate code in panel drivers.
Also lgphilips-lb035q02, nec-nl8048hl11-01b, picodlp and
tpo-td043mtea1 gain support of reading timings over sysfs.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss driver needs to use the omap_pm_set_min_bus_tput(), so add a new
entry for that in omapdss's platform data, and set it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Kevin Hilman <khilman@ti.com>
For now, it just contains the hack for cirrusfb on Amiga, which is moved
out of <video/vga.h> with some slight modifications (use raw_*() instead of
z_*(), which are defined on all m68k platforms).
This makes it safe to include <video/vga.h> in all contexts. Before it
could fail to compile with
include/video/vga.h: In function ‘vga_mm_r’:
include/video/vga.h:242: error: implicit declaration of function ‘z_readb’
include/video/vga.h: In function ‘vga_mm_w’:
include/video/vga.h:247: error: implicit declaration of function ‘z_writeb’
include/video/vga.h: In function ‘vga_mm_w_fast’:
include/video/vga.h:253: error: implicit declaration of function ‘z_writew’
or
include/video/vga.h:23:21: error: asm/vga.h: No such file or directory
depending on the value of CONFIG_AMIGA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
sh_mipi uses some clocks, but the method of setup depends on CPU.
Current SuperH (like sh73a0) can control all of these clocks
by CPG (Clock Pulse Generator).
It means we can control it by clock framework only.
But on sh7372, it needs CPG settings AND sh_mipi PHYCTRL::PLLDS,
and only sh7372 has PHYCTRL::PLLDS.
But on current sh_mipi driver, PHYCTRL::PLLDS of sh7372 was
overwrote since the callback timing of clock setting was changed
by c2658b70f0
(fbdev: sh_mipi_dsi: fixup setup timing of sh_mipi_setup()).
To solve this issue, this patch adds extra .phyctrl.
This patch adds detail explanation for unclear mipi settings
and fixup wrong PHYCTRL::PLLDS value for ap4evb (0xb -> 0x6).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The meram_register(), meram_unregister() and meram_update() operations
check that the pointers they get from the caller are not NULL. Those
checks can be remove, as the caller already ensures that the pointers
are valid.
The platform sanity checks can also be removed, as the operations can't
be accessed without valid platform data anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Remove the RGB or Y/C base address update from the meram_register()
operation, as this belongs to the meram_update() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of copying the whole platform data structure to struct
sh_mobile_lcdc_chan, store a const pointer to the channel platform data.
MERAM configuration information needs to be changed at runtime, so copy
it to struct sh_mobile_lcdc_chan.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of manually specifying the ICBs to use in platform data,
allocate them automatically at runtime. The range of reserved ICBs (for
instance to be used through UIO), if any, is passed in the platform data
reserved_icbs field as a bitmask.
The MERAM registration function now returns a pointer to an opaque MERAM
object, which is passed to the update and unregistration functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Instead of requiring the users to hardcode MERAM allocation in platform
data, allocate blocks at runtime using genalloc.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The new structure stores ICB parameters for ICBs.
Instead of modifying the struct sh_mobile_meram_cfg instances passed by
callers, store the ICB parameters internally and make the public API
take const pointers to sh_mobile_meram_cfg.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Many variables, such as loop counters, sizes and offsets, should be
unsigned integers. Make them so.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The structure describe ICB configuration, no ICB objects themselves.
Rename it to sh_mobile_meram_icb_cfg in preparation for the addition of
an ICB structure.
All the structure fields are unsigned integers, make them so.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The struct sh_mobile_lcdc_chan_cfg platform data contains a list of
video modes. Name the lcd_cfg and num_cfg fields to reflect that they
describe video modes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Pass a pointer to the transmitter device through platform data, retrieve
the corresponding sh_mobile_lcdc_entity structure in the probe method
and call the transmitter display_on/off methods directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fix race conditions with unplug/replug behavior, in particular
take care not to hold up USB probe/disconnect for long-running
framebuffer operations and rely on usb to handle teardown.
Fix for kernel panic reported with new F17 multiseat support.
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Now that we have platform data contained within the individual board
code, we can get rid of the global function pointers, placing them
inside the platform data instead.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the LCD data structures to an include file which can be shared
with the board code in arch/arm/mach-sa1100.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Samsung EXYNOS SoC such Exynos5 has DP controller and embedded DP
panel can be used. This patch supports DP driver based on Samsung
EXYNOS SoC chip.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Samsung S5PC210 and EXYNOS SoC platform has MIPI-DSI controller and
MIPI-DSI based LCD Panel could be used with it. This patch supports
MIPI-DSI driver based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
machine code and LCD panel driver specific function registered to
mipi_dsim_ddi structure at lcd panel init function called system init. In
the MIPI-DSI driver, find lcd panel driver by using registered lcd panel
name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)
iQIcBAABAgAGBQJPMG54AAoJECSVL5KnPj1PR6QQAKOoD4luFRw2F85jdk4GYBiX
WqUWc1OlKYxCGIhk6LpV6fwBLDZCTjOw9NU/9i3JIOHAscGzqVvUce1zYwolEu0B
tTH15/6Bh6uuRJEKYF8H53t1vsbrutssvUsqVcJsHrfie6bVjqjGV18cLT9siVy5
jEZnU958Nb7t8hk7Af1ppQkbB4cpExHX4k3hXTKM+dOkRWMaH1fHv2dnikKuYXDq
G7PC57VqN89DP14M+isUGt5uUgaMSmI09VdTYZ8xgULaZwOxnfOQNnceb/AaKnTY
I2oHDNlNwmiHVgafN7uS0tAhIqnlYOAVLJNLlDfL7xC71AyH6WtzwJuhXnqun7v6
moSwzzGKHohCXyeTjMAthx6HyLq55fBPAI1CmEEtmFLMv1tADLAp9Rm4dsaAjyF8
7aKJO/9iGEpolLYjAGJGGjgCALa+/NWdXnW/zP/2vmcjAaPOZtd0YlD3OaPYr31p
0cImhG57xIAfh60BRq+/FDthEN478Xj8f2jRe/2nsonw8JuFodZZ6nUaFeQS25X/
X/07Wkvmz2CY8FoPeXDHaKO8B1wJphzvY2iJjDwI1jg8u/PT2agILNM24tH3SVky
s6nyBLOEBHZh7mVwll2YifjZ6zzJm4y09LzgZpqXmUXOYPDn5JP9yZE4+R23RaEY
kVz8fkE/FjmjAlx/WjKa
=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'for-next' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: Split trivial #if defined(__KERNEL__) && X conditionals
UAPI: Don't have a #elif clause in a __KERNEL__ guard in linux/soundcard.h
UAPI: Fix AHZ multiple inclusion when __KERNEL__ is removed
UAPI: Make linux/patchkey.h easier to parse
UAPI: Fix nested __KERNEL__ guards in video/edid.h
UAPI: Alter the S390 asm include guards to be recognisable by the UAPI splitter
UAPI: Guard linux/cuda.h
UAPI: Guard linux/pmu.h
UAPI: Guard linux/isdn_divertif.h
UAPI: Guard linux/sound.h
UAPI: Rearrange definition of HZ in asm-generic/param.h
UAPI: Make FRV use asm-generic/param.h
UAPI: Make M32R use asm-generic/param.h
UAPI: Make MN10300 use asm-generic/param.h
UAPI: elf_read_implies_exec() is a kernel-only feature - so hide from userspace
UAPI: Don't include linux/compat.h in sparc's asm/siginfo.h
UAPI: Fix arch/mips/include/asm/Kbuild to have separate header-y lines
Disables the internal pull resistor for SDA and SCL which are enabled by
default, as there are external pull up's in 4460 and 4430 ES2.3
SDP, Blaze and Panda Boards, It is done to avoid the EDID read failure.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move duplicate HDMI mux_init code from omap4 and panda board file
to display file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_overlay_manager contains device_changed field, which no longer has
any use. So remove the field and the few places where it is touched.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Setting overlay's output channel is currently handled at the same time
as other overlay attributes. This is not right, as the normal attributes
should only affect one overlay and manager, but changing the channel
affects two managers.
This patch moves the channel field into the "extra_info" set, handled
together with enabled-status.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlayr contains info and info_dirty fields, both of which
should be internal to apply.c.
This patch moves those fields into ovl_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlay_manager contains info and info_dirty fields, both of
which should be internal to apply.c.
This patch moves those fields into mgr_priv data, and names them
user_info and user_info_dirty.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlays are currently enabled and disabled with a boolean in the struct
omap_overlay_info. The overlay info is set with ovl->set_overlay_info(),
and made into use with mgr->apply().
This doesn't work properly, as the enable/disable status may affect also
other overlays, for example when using fifo-merge. Thus the enabling and
disabling of the overlay needs to be done outside the normal overlay
configuration.
This patch achieves that by doing the following things:
1) Add function pointers to struct omap_overlay: enable(), disable() and
is_enabled(). These are used to do the obvious. The functions may block.
2) Move the "enabled" field from struct omap_overlay to ovl_priv_data.
3) Add a new route for settings to be applied to the HW, called
"extra_info". The status of the normal info and extra_info are tracked
separately.
The point here is to allow the normal info to be changed and
applied in non-blocking matter, whereas the extra_info can only be
changed when holding the mutex. This makes it possible to, for example,
set the overlay enable flag, apply it, and wait until the HW has taken
the flag into use.
This is not possible if the enable flag would be in the normal info, as
a new value for the flag could be set at any time from the users of
omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct omap_overlay_manager contains "enabled"-field, used to track if
the manager is enabled or not. This field should be internal to apply.c.
This patch moves the field to mgr_priv_data, and applies the necessary
locking when accessing the field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current code uses dsi_video_mode_enable/disable functions to
enable/disable DISPC output for video mode displays. For command mode
displays we have no notion in the DISPC side of whether the panel is
enabled, except when a dss_mgr_start_update() call is made.
However, to properly maintain the DISPC state in apply.c, we need to
know if a manager used for a manual update display is currently in use.
This patch achieves that by changing dsi_video_mode_enable/disable to
dsi_enable/disable_video_output, which is called by both video and
command mode displays. For video mode displays it starts the actual
pixel stream, as it did before. For command mode displays it doesn't do
anything else than mark that the manager is currently in use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Current way of handling overlay-manager links is a bit strange: each
manager has a static array, containing pointers to all the overlays
(even those used by other managers). The overlays contain a pointer to
the manager being used.
This patch makes the system a bit saner: each manager has a linked list
of overlays, and only the overlays linked to that manager are in the
list.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlay managers are stored in a linked list. There's no need for this
list, as an array would do just as fine.
This patch changes the code to use an array for overlay managers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "enabled" field to struct omap_overlay_manager, which tells if the
output is enabled or not. This will be used in apply.c in the following
patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_overlay_manager struct contains enable() and disable() functions.
However, these are only meant to be used from inside omapdss, and thus
it's bad to expose the functions.
This patch adds dss_mgr_enable() and dss_mgr_disable() functions to
apply.c, which handle enabling and disabling the output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Partial update for manual update displays has never worked quite well:
* The HW has limitations on the update area, and the x and width need to
be even.
* Showing a part of a scaled overlay causes artifacts.
* Makes the management of dispc very complex
Considering the above points and the fact that partial update is not
used anywhere, this and the following patches remove the partial update
support. This will greatly simplify the following re-write of the apply
mechanism to get proper locking and additional features like fifo-merge.
This patch removes the partial update from the dsi.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
SH MIPI manual explains the calculation method of HBP/HFP.
it is based on HSbyteCLK settings.
SH73a0 chip can use HS6divCLK/HS4divCLK for it.
This patch has compatibility to SH7372 mipi
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Dot clock of SH MIPI are depends on each platform board.
This patch adds set_dot_clock() function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
SH MIPI DSI can use 0-4 lane
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add zorder support on OMAP4, this feature allows deciding the visibility order
of the overlays based on the zorder value provided as an overlay info parameter
or a sysfs attribute of the overlay object.
Use the overlay cap OMAP_DSS_OVL_CAP_ZORDER to determine whether zorder is
supported for the overlay or not. Use dss feature FEAT_ALPHA_FREE_ZORDER
if the caps are not available.
Ensure that all overlays that are enabled and connected to the same manager
have different zorders. Swapping zorders of 2 enabled overlays currently
requires disabling one of the overlays.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for VIDEO3 pipeline on OMAP4:
- Add VIDEO3 pipeline information in dss_features and omapdss.h
- Add VIDEO3 pipeline register coefficients in dispc.h
- Create a new overlay structure corresponding to VIDEO3.
- Make changes in dispc.c for VIDEO3
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP3, in order to enable alpha blending for LCD and TV managers, we needed
to set LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits in DISPC_CONFIG. On
OMAP4, alpha blending is always enabled by default, if the above bits are set,
we switch to an OMAP3 compatibility mode where the zorder values in the pipeline
attribute registers are ignored and a fixed priority is configured.
Rename the manager_info member "alpha_enabled" to "partial_alpha_enabled" for
more clarity. Introduce two dss_features FEAT_ALPHA_FIXED_ZORDER and
FEAT_ALPHA_FREE_ZORDER which represent OMAP3-alpha compatibility mode and OMAP4
alpha mode respectively. Introduce an overlay cap for ZORDER. The DSS2 user is
expected to check for the ZORDER cap, if an overlay doesn't have this cap, the
user is expected to set the parameter partial_alpha_enabled. If the overlay has
ZORDER cap, the DSS2 user can assume that alpha blending is already enabled.
Don't support OMAP3 compatibility mode for now. Trying to read/write to
alpha_blending_enabled sysfs attribute issues a warning for OMAP4 and does not
set the LCDALPHABLENDERENABLE/TVALPHABLENDERENABLE bits.
Change alpha_enabled to partial_alpha_enabled in the omap_vout driver. Use
overlay cap "OMAP_DSS_OVL_CAP_GLOBAL_ALPHA" to check if overlay supports alpha
blending or not. Replace this with checks for VIDEO1 pipeline.
Cc: linux-media@vger.kernel.org
Cc: Lajos Molnar <molnar@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
overlay_info struct, used to configure overlays, currently includes both
physical and virtual addresses for the pixels. The vaddr was added to
support more exotic configurations where CPU would be used to update a
display, but it is not currently used and there has been no interest in
the feature. Using CPU to update a screen is also less interesting now
that OMAP4 has two LCD outputs.
This patch removes the vaddr field, and modifies the users of omapdss
accordingly. This makes the use of omapdss a bit simpler, as the user
doesn't need to think if it needs to give the vaddr.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This is a driver for N800's display, ported from the old omapfb. This is
a slightly lighter version of the driver as not all features of the old
driver can be ported without big changes to DSS2, and also because some
of the HW features used in the old driver are unclear (e.g. the power
management part).
That said, the new driver works fine for basic use.
Architecturally the driver is not as neat as it could be. N800's display
HW consists of a display buffer chip and a panel, and ideally they would
be represented by separate, independent drivers. This is not currently
possible, and this driver contains both buffer chip and panel driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Taal panel driver supports two kinds of backlight control: 1) using DSI
commands sent to the panel to control the backlight, 2) calling function
pointers going to the board file to control the backlight.
The second option is a bit hacky, and will no longer be needed when the
PWM driver supports the backlight features. After that we can use the
standard PWM backlight driver.
This patch removes the second backlight control mechanism, and adds a
boolean field, use_dsi_backlight, to nokia_dsi_panel_data which the
board file can use to inform whether the panel driver should use DSI
commands to control the backlight.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have currently panel-generic-dpi driver, which is a combined driver
for dummy panels and also for DVI output.
The aim is to split the panel-generic-dpi into two, one for fixed size
dummy panels connected via DPI, and the other (this) for variable
resolution output which supports DDC channel (in practice a DVI framer
chip connected to DPI output).
Original i2c code by: Ricardo Salveti de Araujo
<ricardo.salveti@canonical.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
regn divider is currently programmed to the registers without change,
but when calculating clock frequencies it is used as regn+1.
To make this similar to how DSI handles the dividers this patch changes
the regn value to be used as such for calculations, but the value
programmed to registers is regn-1.
This simplifies the clock frequency calculations, makes it similar to
DSI, and also allows us to use regn value 0 as undefined.
Cc: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add initial support for DSI video mode panels:
- Add a new structure omap_dss_dsi_videomode_data in the member "panel" in
omap_dss_device struct. This allows panel driver to configure dsi video_mode
specific parameters.
- Configure basic DSI video mode timing parameters: HBP, HFP, HSA, VBP, VFP, VSA,
TL and VACT.
- Configure DSI protocol engine registers for video_mode support.
- Introduce functions dsi_video_mode_enable() and dsi_video_mode_disable() which
enable/disable video mode for a given virtual channel and a given pixel format
type.
Things left for later
- Add functions to check for errors in video mode timings provided by panel.
- Configure timing registers required for command mode interleaving.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, DSI pixel info is only represented by the pixel size in bits using
the pixel_size parameter in omap_dss_device struct's ctrl member.
This is not sufficient information for DSI video mode usage, as two of the
supported formats(RGB666 loosely packed, and RGB888) have the same pixel
container size, but different data_type values for the video mode packet header.
Create enum "omap_dss_dsi_pixel_format" which describes the pixel data format
the panel is configured for. Create helper function dsi_get_pixel_size() which
returns the pixel size of the given pixel format.
Modify functions omapdss_default_get_recommended_bpp() and dss_use_replication()
to use dsi_get_pixel_size().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce read functions which use generic Processor-to-Peripheral
transaction types. These are needed by some devices which may not support
corresponding DCS commands.
Add function dsi_vc_generic_send_read_request() which can send
a short packet with 0, 1 or 2 bytes of request data and the corresponding
generic data type.
Rename function dsi_vc_dcs_read_rx_fifo() to dsi_vc_read_rx_fifo() and modify
it to take the enum "dss_dsi_content_type" as an argument to use either DCS
or GENERIC Peripheral-to-Processor transaction types while parsing data read
from the device.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove functions dsi_vc_dcs_read_1() and dsi_vc_dcs_read_2(), these are used
when the panel is expected to return 1 and 2 bytes respecitvely. This was manily
used for debugging purposes. These functions should be implemented in the panel
driver if needed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Intoduce enum "dss_dsi_content_type" to differentiate between DCS and generic
content types.
Introduce short and long packet write functions which use generic
Processor-to-Peripheral transaction types. These are needed by some devices
which may not support corresponding DCS commands. Create common write functions
which allow code reuse between DCS and generic write functions.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Create an enum for DSI operation modes, use this to set the capabilities of the
device in dsi_init_display().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add OMAP_DSS_OVL_CAP_GLOBAL_ALPHA and OMAP_DSS_OVL_CAP_PRE_MULT_ALPHA to
overlay capabilities. Use these instead of FEAT_GLOBAL_ALPHA,
FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA in code.
Remove FEAT_GLOBAL_ALPHA_VID1 and FEAT_PRE_MULT_ALPHA which are no
longer used. FEAT_GLOBAL_ALPHA is still used to decide if the HW has
global alpha register.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Remove support for non-DISPC overlays and overlay managers.
The support to possibly have non-DISPC overlays and managers was made to
make it possible to use CPU and/or sDMA to update RFBI or DSI command
mode displays. It is ok to remove the support, because:
- No one has used the feature.
- Display update without DISPC is very slow, so it is debatable if the
update would even be usable.
- Removal cleans up code.
- If such a feature is needed later, it is better implemented outside
omapdss driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Archit Taneja <archit@ti.com>
Currently when changing the manager of an overlay, set_manager() directly
calls dispc to set the overlay's destination.
Change this to be more in line with other overlay configurations, and
this will also remove the need to have dispc clocks enabled when calling
set_manager().
A new field is added to overlay struct, "manager_changed". This is
similar to "display_changed" field in manager struct, and is used to
inform apply that the manager has changed and thus write to the
registers is needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PicoDLP is a micro projector from TI.
DLP used in OMAP4 is dpp2600 (DLP Pico Projector) The DLP requires
commands to be sent over i2c for configurations. To know more about
dpp2600 commands please visit:
https://focus.ti.com/myti/docs/extranet.tsp?sectionId=403
The picodlp module consists of a dss driver and an i2c_client.
To know more please visit:
http://www.omappedia.org/wiki/PicoDLP_projector_guide
Based on original design from Mythri P K <mythripk@ti.com>
Signed-off-by: Mayuresh Janorkar <mayur@ti.com>
Signed-off-by: Mythri P K <mythripk@ti.com>
[tomi.valkeinen@ti.com: squashed commits]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes earlier problems where monitor would not return from blank
Test with any DisplayLink-based USB 2.0 graphics adapter
sudo nano /sys/class/graphics/fb?/blank
and write out single digit FB_BLANK_* code from include/linux/fb.h
Supports on (0), blank (1), suspend (2,3), powerdown (4)
Signed-off-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Instead of hardcoding register values through the driver, define macros
for individual register bits using the register name and the bit name,
and use the macros.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The function to get device's context loss count has changed from
omap_pm_get_last_off_on_transaction_id() to
omap_pm_get_dev_context_loss_count()
Change name of the function pointer in omapdss.h accordingly, and use
the term "context loss count" instead of "context id" in the code.
Restructure the context loss count functions to handle errors properly,
and ensure that context is always considered lost if an error happens.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add Color Phase Rotation (CPR) support and sysfs files to enable CPR and
to set the CPR coefficient matrix.
CPR is enabled via manager?/cpr_enable file, and the coefficient matrix
is set via manager?/cpr_coef file. The values in cpr_coef are in the
following order:
RR RG RB GR GG GB BR BG BB
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove the whole update_mode stuff from omapdss driver. If automatic
update for manual update displays is needed, it's better implemented in
higher layers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss.h included platform_device.h and atomic.h, neither of which is
needed by omapdss.h. Remove those includes from omapdss.h, and fix the
affected .c files which did not include platform_device.h even though
they should.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since the NV24 framebuffer has a CbCr plane that is twice as wide
as the Y plane, it needs to be handled as a special case.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Based on the patch by Takanari Hayama <taki@igel.co.jp>
Adds support framework necessary to use Media RAM (MERAM)
caching functionality with the LCDC. The MERAM is accessed
through up to 4 Interconnect Buffers (ICBs).
ICB numbers and MERAM address ranges to use are specified in
by filling in the .meram_cfg member of the LCDC platform data
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the support for NV12 color format.
Configure base address for UV component of NV12 color format.
Change the way chroma scaling is handled for YUV formats on OMAP4 by enabling
chroma-resampling for video pipeline and hence using FIR2 register set for
scaling UV.
Changes to _dispc_set_scaling(), because of the reason above, are:
- call _dispc_set_scaling_common() to handle scaling for all color formats
except for OMAP4 where it only handles scaling for RGB or Y-component
- call _dispc_set_scaling_uv() for special handling required for UV
component on OMAP4.
- dispc_set_scaling_uv() also resets chroma-resampling bit for RGB color modes.
Contains chroma scaling (_dispc_set_scaling_uv) design and implemented by
Lajos Molnar <molnar@ti.com>
Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new color formats supported by OMAP4: NV12, RGBA16, RGBX16,
ARGB16_1555, XRGB16_1555.
NV12 color format is defined here, its support in DSS will be added separately.
Signed-off-by: Amber Jain <amber@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On OMAP3, the DSI module has 2 data lanes. On OMAP4, DSI1 has 4 data lanes
and DSI2 has 2 data lanes. Introduce function dsi_get_num_data_lanes() which
returns the number of data lanes on the dsi interface, introduce function
dsi_get_num_data_lanes_dssdev() which returns the number of data lanes used by
the omap_dss_device connected to the lanes.
Use the DSI_GNQ register on OMAP4 to get the number of data lanes, modify
dsi.c to use the number of lanes and the extra data lanes on DSI1.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add omap_rfbi_configure() which the panel driver can use to reconfigure
the data element size and the number of data lines in the RFBI bus.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add similar bus lock to RFBI as is in DSI. The panel driver can use the
bus lock to mark that the RFBI bus is currently in use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Introduce DSI2 PLL clock sources needed by LCD2 channel and DSI2 Protocol
engine and DISPC Functional clock. Do the following:
- Modify dss_get_dsi_clk_source() and dss_select_dsi_clk_source() to take the
dsi module number as an argument.
- Create debugfs files for dsi2, split the corresponding debugfs functions.
- Allow DPI to use these new clock sources.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI interface is represented as a platform device, using the DSI platform
driver(dsi.c). The current DSI driver design is capable of running only one
instance of a DSI device. On OMAP4, there are 2 very similar DSI modules which
can be represented as instances of "omapdss_dsi" platform device.
Add member "module" in "dssdev.phy.dsi" that tells us which DSI module's lanes
the panel is connected to. Modify dsi.c functions to take the device's
platform_device struct pointer, provide functions dsi_get_dsidev_from_dssdev()
and dsi_get_dsidev_from_id() take the panel's omap_dss_device and module number
respectively, and return the platform_device pointer. Currently, the dsi struct
is declared globally and is accessed when dsi data is needed. The new pdev
argument will be used later to provide the platform device's dsi related data.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add pointer to omap_dss_device struct as an argument in the functions which
are exported to dsi panel drivers. This argument will tell the DSI driver
which DSI interface's data it has to choose.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ULPS is a low power state where the DSI lanes are kept at ground. This
patch implements ULPS by having a DSI bus inactivity timer which
triggers the entry to ULPS. ULPS exit will happen automatically when the
driver needs to do something on the DSI lanes.
The ulps_timeout is configurable from board file or via sysfs.
Additionally another sysfs file, "ulps", can be used to check the
current ULPS state, or to manually enter or exit ULPS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
ESD check in Taal driver is currently on/off feature with hardcoded
interval. This patch changes it to a configurable interval, which can be
set from the board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dsi_mux_pads function pointer to omap_dss_board_info, and use the
function pointer in DSI code to configure the DSI pads either to normal
DSI operation, or to pull down when in ULPS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add parameter to omapdss_dsi_display_disable() which the panel driver
can use to tell if the DSI lanes should be put to ULPS before disabling
the interface.
This can be used to skip ULPS entry in cases where the panel doesn't
care about ULPS state, for example when the panel will be reset, or when
the display interface will be enabled again right after the disable.
This will speed up the operation considerably in cases where entering
ULPS would fail with timeout, and the panel driver isn't even interested
in entering ULPS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI pins are powered by VDDS_DSI. If VDDS_DSI is off, the DSI pins
are floating even if they are pinmuxed to, say, safe mode and there's a
pull down/up.
This patch gives the panel drivers an option to leave the VDDS_DSI power
enabled while the DSS itself is turned off. This can be used to keep the
DSI lanes in a valid state while DSS is off, if the DSI pins are muxed
for pull down (not done in this patch).
There will be a slight power consumption increase (~100 uA?) when the
VDDS_DSI is left on, but because this option is used when the panel is
left on, the regulator consumption is negligible compared to panel power
consumption.
When the panel is fully turned off the VDDS_DSI is also turned off.
As an added bonus this will give us faster start up time when starting
up the DSS and the regulator is already enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move some of the configurable HDMI PLL parameters to dssdev.clock struct.
Cleanup the function hdmi_compute_pll() by using the parameters defined in the
board file and do some cosmetic modifications.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add enum dss_clock_source in dssdev.clocks struct so that the clock sources can
be specified in the board file.
Replace hard coded clock sources in dsi.c, dpi.c and replace them with the new
clock source members in dssdev.clocks. Modify the sdp4430_lcd_device struct in
board-4430sdp.c to specify clock sources for DISPC_FCLK, LCD1_CLK and DSI1_FCLK.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change enum dss_clk_source to omap_dss_clock_source and move it to
'plat/display.h'. Change the enum members to attach "OMAP_" in the beginning.
These changes are done in order to specify the clock sources for DSS in the
board file.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dss_register_device and omap_dss_unregister_device can only be
called from core.c, so we can make it static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add get_dimensions() to struct omap_dss_driver. Use the call, if supported
by the driver, in OMAPFB.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clock configuration was defined inside dssdev.phy.dsi struct. The clock
config doesn't really belong there, and so it's moved to dssdev.clock
struct.
Now the explicit clock configuration could also be used for other
interfaces than DSI, although there's no support for it currently.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/nokia-dsi-panel.h is an include for the
OMAP DSS panel driver for Nokia's DSI displays. A more logical place for
it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/panel-generic-dpi.h is an include for
the OMAP DSS panel driver for generic DPI displays. A more logical place
for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduces lcdc->lcdcon_pol_negative which set CONTRAST_CTR
register to inverted polarity.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Supports YCbCr420sp, YCbCr422sp, and YCbCr44sp, formats
(bpp = 12, 16, and 24) respectively.
When double-buffering both Y planes appear before the C planes (Y-Y-C-C),
as opposed to Y-C-Y-C.
Set .nonstd in struct sh_mobile_lcdc_chan_cfg to enable YUV mode, and use
.bpp to distiguish between the 3 modes.
The value of .nonstd is copied to bits 16-31 of LDDFR in the LCDC and
should be set accordingly.
.nonstd must be set to 0 for RGB mode.
Due to the encoding of YUV data, the framebuffer will clear to green
instead of black.
In YUV 420 mode, panning is only possible in 2 line increments.
Additionally in YUV 420 mode the vertical resolution of the framebuffer
must be an even number.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Support for backlight devices controlled through board-specific
routines. Backlights can be defined per-channel and follow fbdev
directives to switch off as the LCD blanks or is turned on/off.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This kills off all of the dl_xxx() printk wrappers and simply stubs in a
pr_fmt() definition to accomplish the same thing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The register layout of the MIPI DSI unit on sh-mobile SoCs differ. Add platform
parameters to support such variations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Silence warnings such as -
drivers/video/s1d13xxxfb.c:421: warning: ‘bltbit_wait_bitset’ defined but not used
Just drop the unused code.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
udlfb has undergone a fair bit of cleanup recently and is effectively at
the point where it can be liberated from staging purgatory and promoted
to a real driver.
The outstanding cleanups are all minor, with some of them dependent on
drivers/video headers, so these will be done incrementally from udlfb's
new home.
Requested-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is already defined by linux/fb.h now, so punt the duplicate
definition from the driver header.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The HDMI clock has to be reconfigured for different video modes. However, the
precision of the supplying SoC clock on SH-Mobile systems is often
insufficient. This patch allows to additionally reconfigure the parent clock
to achieve the optimal HDMI clock frequency, in case this is supported by the
platform.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
The SH-Mobile HDMI driver runs in several contexts: ISR, delayed work-queue,
task context, when called from the sh_mobile_lcdc framebuffer driver. This
creates ample race possibilities. Even though most these races are purely
theoretical, it is better to close them. To trace fb_info validity we install a
notification callback in the HDMI driver, and the only way for it to get to
driver internal data is by using struct sh_mobile_lcdc_chan, therefore it had
to be extracted into a separate common header.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is a preparation for HDMI hotplug support. This patch just moves all
platform defined video modes for the sh_mobile_lcdcfb driver to separate
arrays and switches all users to use element 0 of that array, so, this patch
doesn't introduce any functional changes and as such should not cause any
regressions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The below updates a broken web address to one(hopefully) thats
the new correct address.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
unifdef-y and header-y has same semantic.
So there is no need to have both.
Drop the unifdef-y variant and sort all lines again
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Some SH-Mobile SoCs have an HDMI controller and a PHY, attached to one of their
LCDC interfaces. This patch adds a preliminary static support for such
controllers, this means, that only the 720p mode is handled ATM. Support for
more modes and a dynamic switching between them will be added by a follow up
patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
HDMI support for the sh_mobile_lcdc framebuffer driver will require a 'struct
fb_info *' pointer for its .display_on() callback. While at it fix kfr2r09
framebuffer modular build.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
FBIO_WAITFORVSYNC is currently implemented by matroxfb, atyfb, intelfb and
more. All of them keep redefining the same FBIO_WAITFORVSYNC macro over
and over again, so move it to linux/fb.h and clean up those duplicate
defines.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Maik Broemme <mbroemme@plusserver.de>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This work includes the following:
- Implement handler for FBIO_WAITFORVSYNC ioctl.
- Allocate the data and palette buffers separately. A consequence of
this is that the palette and data loading is now done in different
phases. And that the LCD must be disabled temporarily after the palette
is loaded but this will only happen once after init and each time the
palette is changed. I think this is OK.
- Allocate two (ping and pong) framebuffers from memory.
- Add pan_display handler which toggles the LCDC DMA registers between
the ping and pong buffers.
Signed-off-by: Martin Ambrose <martin@ti.com>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SH-mobile SoCs have a MIPI DSI controller, that can be used to connect
MIPI displays to LCDC. This patch adds a platform driver for SH-mobile MIPI DSI
unit. It uses existing hooks in the sh_mobile_lcdcfb.c driver for display
activation and deactivation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The LCDC block is allowed to use one of the two output data formats, when used
with MIPI DSI: RGB24 and YUV422. YUV422 is not currently handled by the LCDC
driver, but we have to add a define for it for MIPI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This header adds defines for MIPI DSI and DCS commands and data formats. See
http://www.mipi.org/ for details.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds waveform storing capability to broadsheetfb. It uses the
firmware class to retrieve the waveform, and the request to initiate the
waveform storing is done via a driver sysfs entry, loadstore_waveform.
Broadsheet is a framebuffer device. It is slightly different from a
typical framebuffer controller that drives a normal TFT-LCD display. Most
E-Ink display panels require a waveform in order to function. That is, in
order to drive the state of a pixel to black, gray, or white, a specific
waveform is utilized. Basically, that waveform represents the specific
E-field wiggling needed to get the pixel to its optimal state given
current temperature, and its previous state. TN/IPS-LCDs use a similar
concept but the driving waveform is sufficiently simple that it is
internalized in the TFT source/gate driver.
These E-Ink waveforms are specific to a production batch. That is, a
batch of display films are produced, then they get characterized and a
waveform is generated for that batch. Broadsheet, typically, is attached
to its private SPI flash which is then flashed with this waveform.
Users won't be able to see the waveform and typically won't ever need to
know about it. If however, the display panel attached to broadsheet is
changed out, then they will need to update their waveform. That would
typically be done at a factory or repair facility rather than by a user.
[akpm@linux-foundation.org: fix printk warning]
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow boards with GP-MMIO controllers to provide hooks to broadsheetfb in
order to offload cmd/data writes and data reads instead of relying only on
host based GPIO wiggling.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update broadsheetfb to add support for multiple panel types. The 3.7" and
6" are known to work but the 9.7" is untested due to lack of hardware.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added FBIO_WAITFORVSYNC ioctl for SH-Mobile devices.
Tested on MS7724 and MigoR boards against 2.6.33-rc7.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
sh: Fix test of unsigned in se7722_irq_demux()
sh: mach-ecovec24: Add FSI sound support
sh: mach-ecovec24: Add mt9t112 camera support
sh: mach-ecovec24: Add tw9910 support
sh: MSIOF/mmc_spi platform data for the Ecovec24 board
sh: ms7724se: Add ak4642 support
sh: Fix up FPU build for SH5
sh: Remove old early serial console code V2
sh: sh5 scif pdata (sh5-101/sh5-103)
sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
sh: sh2 scif pdata (sh7616)
sh-sci: Extend sh-sci driver with early console V2
sh: Stub in P3 ioremap support for nommu parts.
sh: wire up vmallocinfo support in ioremap() implementations.
sh: Make the unaligned trap handler always obey notification levels.
sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
...
Add a helper function to enable raster. Also add one member in the
private data structure to track the current blank status, another function
pointer which takes in the platform specific callback function to control
panel power.
These updates will help in adding suspend/resume and frame buffer blank
operation features.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a ->start_transfer() callback to the
driver sh_mobile_lcdcfb.c. The callback is used to
program the LCDC panel in the case of one-shot mode.
Needed by the LCD controller used on the KFR2R09 board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cleanup the usage of DBE_VT_SIZE since the kernel already defines the
same macro for the same propose.
Also clean up a surrounding whitespaces.
Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the previous version, return values in ioctl() function have been
modified.
[akpm@linux-foundation.org: simplify lcd_disable_raster()]
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Steve Chen <schen@mvista.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add LCD controller (LCDC) driver for TI's DA8xx/OMAP-L1xx architecture.
LCDC specifications can be found at http://www.ti.com/litv/pdf/sprufm0a.
LCDC on DA8xx consists of two independent controllers, the Raster
Controller and the LCD Interface Display Driver (LIDD) controller. LIDD
further supports character and graphic displays.
This patch adds support for the graphic display (Sharp LQ035Q3DG01) found
on the DA830 based EVM. The EVM details can be found at:
http://support.spectrumdigital.com/boards/dskda830/revc/.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Steve Chen <schen@mvista.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
DESC
davinci-fb-frame-buffer-driver-for-ti-da8xx-omap-l1xx-fix
EDESC
From: Andrew Morton <akpm@linux-foundation.org>
fix kconfig indenting
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerated bitblt functions to s1d13xxx based video chipsets, more
specificly functions copyarea and fillrect.
It has only been tested and activated for 13506 chipsets but is expected
to work for the majority of s1d13xxx based chips. This patch also cleans
up the driver with respect of whitespaces and other formatting issues. We
update the current status comments.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver is originally written by Lennert, modified by Green to be
feature complete, and ported by Jun Nie and Kevin Liu for pxa168/910
processors.
The patch adds support for the on-chip LCD display controller, it
currently supports the base (graphics) layer only.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Green Wan <gwan@marvell.com>
Cc: Peter Liao <pliao@marvell.com>
Signed-off-by: Jun Nie <njun@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
commit ddb53d48da ("fbdev: remove cyblafb
driver") removed drivers/video/cyblafb.c, but not its .h file
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "Jani Monoses" <jani@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The I2C functionality provided by the i2c-voodoo3 driver is moved into the
tdfxfb (frame buffer driver for Voodoo3 cards). This way there is no
conflict between the i2c driver and the fb driver.
The tdfxfb does not make use from the DDC functionality yet but provides
all the functionality of the i2c-voodoo3 driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The s1d13xxx chip provides two values of identification value: the
Production id (e.g 13506/13505/13806..) and a revision number 0,1,2,3).
Together these can help us to differentiate between similiar setups.
This patch adds the proper way of grabbing both those values and save them
for future reference (in order to decide what functions a card supports,
e.g acceleration).
We also move away from the concept of all s1d13xxx = s1d13806 when we
really support alot more.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: simplify s1d13xxxfb_probe()]
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With a postfix decrement t reaches -1 on timeout which results in a
return of 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix 8bpp mode by adding handling of the Laguna chipsets to various places
and stop trashing a HDR register which probably does not exist on the
Laguna.
Fix compilation warnings about uninitialized variables also.
Finally, all 8bpp, 16bpp and 32bpp modes work on the Laguna chipset.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add additional overflow register setting for Laguna chips.
Also, simplify some code in the cirrusfb_pan_display() and
cirrusfb_blank().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix trailing whitespace because quilt complained about it.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the E-Ink Broadsheet display controller.
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix namespace violations by changing non-kconfig CONFIG_ names to CNFG_*.
Fixes breakage in staging/, which adds a real CONFIG_PANEL.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fix the following 'make headers_check' warning:
usr/include/video/uvesafb.h:5: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/video/sisfb.h:25: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/video/sisfb.h:78: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
This patch adds sh_mobile_lcdcfb deferred io support for SYS panels.
The LCDC hardware block managed by the sh_mobile_lcdcfb driver supports
RGB or SYS panel configurations. SYS panels come with an external display
controller that is resposible for refreshing the actual LCD panel. RGB
panels are controlled directly by the LCDC and they need to be refreshed
by the LCDC hardware.
In the case of SYS panels we can save some power by configuring the LCDC
hardware block in one-shot mode. In this one-shot mode panel refresh is
managed by software. This works well together with deferred io since it
allows us to stop clocks for most of the time and only enable clocks when
we actually want to trigger an update. When there is no fbdev activity
the clocks are kept stopped which allows us to deep sleep.
The refresh rate in deferred io mode is set using platform data. The same
platform data can also be used to disable deferred io mode.
As with other deferred io frame buffers user space code should use fsync()
on the frame buffer device to trigger an update.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit b1ee26bab1, along with
the "fixes" for it that all just caused problems:
- c4c6fa9891 "radeonfb: fix problem with
color expansion & alignment"
- f3179748a1 "radeonfb: Disable new color
expand acceleration unless explicitely enabled"
because even when disabled, it breaks for people. See
http://bugzilla.kernel.org/show_bug.cgi?id=12191
for the latest example.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: James Cloos <cloos@jhcloos.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Jean-Luc Coulon <jean.luc.coulon@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changed because old the definition of unsigned long cannot be negative.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add platform data flags for detailed lcd display configuration.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove lddckr from the platform data, these days we calculate the
register value from clock source and clock dividers anyway.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The Epson s1d13xxx hardware is common in many handhelds, but our driver is
currently locked to a single chip revision. This patch adds an array of
known to work revisions (which can be extended).
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Acked-by: Thibaut Varène <varenet@parisc-linux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement support for HW color expansion of 1bpp images, along with some
improvements to the FIFO handling and other accel operations.
The offset fixup code is now unnecessary as the fbcon core will call our
set_par upon switch back from KD_GRAPHICS before anything else happens. I
removed it as it would slow down accel operations.
The fifo wait has been improved to avoid hitting the HW register as often,
and the various accel ops are now performing better caching of register
values.
Overall, this improve accel performances. The imageblit acceleration does
result in a small overall regression in performances on some machines (on
the order of 5% on some x86), probably becaus the SW path provides a
better bus utilisation, but I decided to ingnore that as the performances
is still very good, and on the other hand, some machines such as some
sparc64 get a 3 fold performance improvement.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a couple of incomplete tests of the chip families in the engine
init/reset code and proper initialization of the destination cache mode.
The result should better match what the latest X radeon driver does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove mutex from the fb_open/fb_release functions as these operations are
mutexed at fb layer.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This provides a workaround for users of sh_mobile_lcdcfb that don't
define HAVE_CLK and have otherwise sane clock initialization.
At the same time, move the sh_mobile_lcdc.h header to include/video/.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
