cx23885_gpio_setup() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This script was moved out of Documentation/dvb, but the
links weren't updated.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Currently clk_freq is ignored entirely, because the cx235840 driver
configures the xtal at the chip defaults. This is an issue if a
board is produced with a non-default frequency crystal. If clk_freq
is not zero the cx25840 will attempt to use the setting provided,
or fall back to defaults otherwise.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The GPIO settings for quadHD boards are wrong. Fix them.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new QuadHD digital only PCIe boards to driver list.
Differentiate them from 888 digital/analog QuadHD models.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new PCIe DVB-S/S2.
A single port Hauppauge HVR-5525
cx23885 + a8293 + m88rs6000t
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add ID of new card revision to driver list
Analog PAL/NTSC capture.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the array buf on the stack, instead make it static.
Makes the object code smaller by over 240 bytes:
Before:
text data bss dec hex filename
21689 22992 416 45097 b029 cx23885-cards.o
After:
text data bss dec hex filename
21348 23088 416 44852 af34 cx23885-cards.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add two new model numbers to suppress this message in kernel log:
cx23885: cx23885[0]: warning: unknown hauppauge model #121029
Add these model numbers:
* Model 121019 - WinTV-HVR4400
* Model 121029 - WinTV-HVR5500
For WinTV-HVR4400 the documentation and my hardware differ:
Documentation says it supports DVB-S/S2 and DVB-T,
but my hardware also supports DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid warnings like those:
drivers/media/pci/ddbridge/ddbridge-core.c: In function 'dvb_input_detach':
drivers/media/pci/ddbridge/ddbridge-core.c:787:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (input->fe) {
^
drivers/media/pci/ddbridge/ddbridge-core.c:792:2: note: here
case 4:
^~~~
...
On several cases, it is just that gcc 7.1 is not capable of
understanding the comment, but on other places, we need an
annotation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
tveeprom_hauppauge_analog() used to need the I2C adapter in
order to print debug messages. As it now uses pr_foo() facilities
since commit 6037b3ca28 ("[media] tveeprom: print log messages
using pr_foo()"), the first argument of the function is not
needed anymore.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of calling printk() directly, use pr_foo()
macros, as suggested at the Kernel's coding style.
Please notice that a conversion to dev_foo() is not trivial,
as several parts on this driver uses pr_cont().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Due to the 80-cols restrictions, and latter due to checkpatch
warnings, several strings were broken into multiple lines. This
is not considered a good practice anymore, as it makes harder
to grep for strings at the source code.
As we're right now fixing other drivers due to KERN_CONT, we need
to be able to identify what printk strings don't end with a "\n".
It is a way easier to detect those if we don't break long lines.
So, join those continuation lines.
The patch was generated via the script below, and manually
adjusted if needed.
</script>
use Text::Tabs;
while (<>) {
if ($next ne "") {
$c=$_;
if ($c =~ /^\s+\"(.*)/) {
$c2=$1;
$next =~ s/\"\n$//;
$n = expand($next);
$funpos = index($n, '(');
$pos = index($c2, '",');
if ($funpos && $pos > 0) {
$s1 = substr $c2, 0, $pos + 2;
$s2 = ' ' x ($funpos + 1) . substr $c2, $pos + 2;
$s2 =~ s/^\s+//;
$s2 = ' ' x ($funpos + 1) . $s2 if ($s2 ne "");
print unexpand("$next$s1\n");
print unexpand("$s2\n") if ($s2 ne "");
} else {
print "$next$c2\n";
}
$next="";
next;
} else {
print $next;
}
$next="";
} else {
if (m/\"$/) {
if (!m/\\n\"$/) {
$next=$_;
next;
}
}
}
print $_;
}
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the Hauppauge WinTV quadHD ATSC version.
IR support has not been provided, all 4 tuners, demodulators etc are working.
Further documentation can be found on Linux TV wiki.
Signed-off-by: Stephen Backway <stev391@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support fo the Hauppauge WinTV quadHD DVB version.
IR support has not been provided, all 4 tuners, demodulators etc are working.
Further documentation can be found on Linux TV wiki.
Signed-off-by: Stephen Backway <stev391@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for these two new cards.
Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's not mix headers used by the core with those headers that
are needed by some driver-specific interface header.
The headers used on drivers were manually moved using:
mkdir include/media/drv-intf/
git mv include/media/cx2341x.h include/media/cx25840.h \
include/media/exynos-fimc.h include/media/msp3400.h \
include/media/s3c_camif.h include/media/saa7146.h \
include/media/saa7146_vv.h include/media/sh_mobile_ceu.h \
include/media/sh_mobile_csi2.h include/media/sh_vou.h \
include/media/si476x.h include/media/soc_mediabus.h \
include/media/tea575x.h include/media/drv-intf/
And the references for those headers were corrected using:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="drv-intf/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUxbzlAAoJEHm+PkMAQRiGtqYIAJ8YlKX9cXKYmXx8/FncINH+
2erj94KyHG080R1uwSq1+7zXWCZUUlxiJnDnsup5rG0dImcicqgOE48oHax1aN6b
yHfPONkTjNJ1HYepuGC3YWCG9wIjPZQ5S8KHrwRjyVoE+ddhe9gWgvArA3jl/fW/
2fYNWekoRoMcRiNb4/w2weyOOBywdSVpmj0WYiwdztysG2ymw5hUXRHJhvSf1AFm
RQJfUHkhCOYpQGY7XFba/1uGhTJfOgDmYAfspAOLzmrXE/DJcCutsVdBZO+12fAL
nhGpM/PkRYxMvwzDKIUoG35qsymYOMqo54oXhr0S2JjyXTGdGmB6qHxIfqnV5Tk=
=O/Lr
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rc6' into patchwork
This is needed in order to get the media fixes applied on -rc6.
Linux 3.19-rc6
* tag 'v3.19-rc6': (891 commits)
Linux 3.19-rc6
dm: fix handling of multiple internal suspends
hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
hwmon: (i5500_temp) Convert to module_pci_driver
hwmon: (i5500_temp) Don't bind to disabled sensors
hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
arm64: dts: add baud rate to Juno stdout-path
Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
Revert "Documentation: Add entry for dell-laptop sysfs interface"
dm cache: fix problematic dual use of a single migration count variable
dm cache: share cache-metadata object across inactive and active DM tables
of/unittest: Overlays with sub-devices tests
KVM: x86: SYSENTER emulation is broken
KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
arm64: dump: Fix implicit inclusion of definition for PCI_IOBASE
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
...
Conflicts:
drivers/media/pci/cx23885/cx23885.h
Unconditionally attaching Si2161/Si2165 demod driver
breaks Hauppauge WinTV Starburst.
So create own card entry for this.
Add card name comments to the subsystem ids.
This fixes a regression introduced in 3.17 by
36efec48e2 ([media] cx23885: Add si2165 support for HVR-5500)
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
CC: stable@vger.kernel.org # for 3.17 and upper
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TechnoTrend CT2-4500 CI is a PCIe device with DVB-T2/C tuner. It is
similar to DVBSky T980C, just with different PCI ID and remote controller.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVBSky T9580 uses Integrated CX23885 IR controller to decode IR signal.
The IR type of DVBSky remote control is RC5.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds basic support for DVBSky T980C card. CI interface is not supported.
DVBSky T980C is a PCIe card with the following components:
- CX23885 PCIe bridge
- Si2168-A20 demodulator
- Si2158-A20 tuner
- CIMaX SP2 CI chip
The demodulator and tuner need firmware. They're the same as used with TT CT2-4650 CI:
https://www.mail-archive.com/linux-media@vger.kernel.org/msg78033.html
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVBSky T9580 is a dual tuner card with one DVB-T2/C tuner and one DVB-S2 tuner. It contains the following components:
- PCIe bridge: Conexant CX23885
- Demod for terrestrial/cable: Silicon Labs Si2168-A30
- Tuner for terrestrial/cable: Silicon Labs Si2158-A20
- Demod for sat: Montage DS3103
- Tuner for sat: Montage TS2022
This patch depends on Max Nibble's patch for m88ds3103 (see patchwork 25312: https://patchwork.linuxtv.org/patch/25312/ ).
3 firmwares are needed:
- Si2168-A30 demod and Si2158-A20 tuner: same as TechnoTrend CT2-4400, https://www.mail-archive.com/linux-media@vger.kernel.org/msg76944.html
- Montage DS3103 demod: same as PCTV 461e, Antti has it on his LinuxTV project page: http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/
IR receiver is not supported.
Values in cx23885_gpio_setup, cx23885_card_setup and dvbsky_t9580_set_voltage as well as the EEPROM read function are taken from the manufacturer provided semi-open source driver. The drivers in question are Linux GPL'd media tree drivers for cx23885 modified by Max Nibble (nibble.max@gmail.com) with proprietary tuner/demod drivers. Max is aware of this patch and has approved my use of the values in this patch.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These addresses are usually out-of-date and the top-level license will
always have the right address. So drop it from these sources.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The same card entry is used for HVR-4400 and HVR-5500.
Only HVR-5500 has been tested.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for Hauppauge model 71100: WinTV-ImpactVCB-e
(PCIe, Retail, half height)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested:
Composite: http://imgur.com/Rb1TCF3
TV: http://imgur.com/KNrfsmv
Firmware used: xc3028-v27.fw
Not tested: audio, component, s-video, mpeg2 encoder, FM radio.
For audio, it uses an CD style cable to connect to the analog "CD_IN" on the motherboard.
I didn't found how to unmute it (alsamixer do not show an CD or AUX channel).
Signed-off-by: Anca Emanuel <anca.emanuel@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Those boards were missing the ISDB-T support.
Most of the work on this patch were done by Alfredo.
My work here were to port this patch from Kernel 3.2 to upstream,
fix the issue caused by the set_frontend bad hook, and add the
Kconfig bits.
Tested on a X8502 board rebranded as:
"Leadership - Placa PCI-e de Captura de Vídeo Híbrida" - product code 3800.
Thanks-to: Alfredo Delaiti <alfredodelaiti@netscape.net>
Tested-by: Alfredo Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch provide only analog support.
The device is based on AF9013 demodulator, XC3028 tuner
and CX23885 chipset; subsystem id: 1461:d939
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This series add remote control support for MyGica X8507.
I test for 2 month under OpenSuse(X64) 11.4 and 12.2 with
kernel 3.4, 3.5, 3.6 also 3.7-rc2 and rc3.
[mchehab@redhat.com: fixed whitespacing - it seems that Alfredo's emailer mangled
it]
Signed-off-by: Alfredo J. Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add basic DVB-S2 support for the Hauppauge HVR-4400 PCIe board.
Thanks to Antti Palosaari and Devin Heitmueller for their
suggestions and testing.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx23885/altera-ci.c:266:5: warning: no previous prototype for 'altera_ci_op_cam' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:301:5: warning: no previous prototype for 'altera_ci_read_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:307:5: warning: no previous prototype for 'altera_ci_write_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:313:5: warning: no previous prototype for 'altera_ci_read_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:319:5: warning: no previous prototype for 'altera_ci_write_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:325:5: warning: no previous prototype for 'altera_ci_slot_reset' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:368:5: warning: no previous prototype for 'altera_ci_slot_shutdown' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:374:5: warning: no previous prototype for 'altera_ci_slot_ts_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:451:5: warning: no previous prototype for 'altera_poll_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:462:6: warning: no previous prototype for 'altera_hw_filt_release' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:584:5: warning: no previous prototype for 'altera_pid_feed_control' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:606:5: warning: no previous prototype for 'altera_ci_start_feed' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:613:5: warning: no previous prototype for 'altera_ci_stop_feed' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:620:5: warning: no previous prototype for 'altera_ci_start_feed_1' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:625:5: warning: no previous prototype for 'altera_ci_stop_feed_1' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:630:5: warning: no previous prototype for 'altera_ci_start_feed_2' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:635:5: warning: no previous prototype for 'altera_ci_stop_feed_2' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:640:5: warning: no previous prototype for 'altera_hw_filt_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:123:5: warning: no previous prototype for 'netup_write_i2c' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:150:5: warning: no previous prototype for 'netup_ci_get_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:169:5: warning: no previous prototype for 'netup_ci_op_cam' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:239:5: warning: no previous prototype for 'netup_ci_read_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:245:5: warning: no previous prototype for 'netup_ci_write_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:251:5: warning: no previous prototype for 'netup_ci_read_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:257:5: warning: no previous prototype for 'netup_ci_write_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:263:5: warning: no previous prototype for 'netup_ci_slot_reset' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:292:5: warning: no previous prototype for 'netup_ci_slot_shutdown' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:298:5: warning: no previous prototype for 'netup_ci_set_irq' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:319:5: warning: no previous prototype for 'netup_ci_slot_ts_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:375:5: warning: no previous prototype for 'netup_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:402:5: warning: no previous prototype for 'netup_poll_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:415:5: warning: no previous prototype for 'netup_ci_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:520:6: warning: no previous prototype for 'netup_ci_exit' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:90:5: warning: no previous prototype for 'netup_read_i2c' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-av.c:26:6: warning: no previous prototype for 'cx23885_av_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-cards.c:1430:5: warning: no previous prototype for 'netup_jtag_io' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-core.c:306:6: warning: no previous prototype for 'cx23885_irq_add' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-dvb.c:662:5: warning: no previous prototype for 'netup_altera_fpga_rw' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-f300.c:150:5: warning: no previous prototype for 'f300_set_voltage' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:249:5: warning: no previous prototype for 'cx23885_input_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:353:6: warning: no previous prototype for 'cx23885_input_fini' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:76:6: warning: no previous prototype for 'cx23885_input_rx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:134:5: warning: no previous prototype for 'cx23885_g_register' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:185:5: warning: no previous prototype for 'cx23885_s_register' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:27:5: warning: no previous prototype for 'cx23885_g_chip_ident' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:101:6: warning: no previous prototype for 'cx23885_ir_tx_v4l2_dev_notify' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:37:6: warning: no previous prototype for 'cx23885_ir_rx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:60:6: warning: no previous prototype for 'cx23885_ir_tx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:76:6: warning: no previous prototype for 'cx23885_ir_rx_v4l2_dev_notify' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23888-ir.c:1203:5: warning: no previous prototype for 'cx23888_ir_probe' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23888-ir.c:1253:5: warning: no previous prototype for 'cx23888_ir_remove' [-Wmissing-prototypes]
drivers/media/pci/cx23885/netup-init.c:109:6: warning: no previous prototype for 'netup_initialize' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds audio support for input YPbPr, AV and S-Video on Mygica X8507 card.
Remains to be done: IR, FM and ISDBT
Signed-off-by: Alfredo J. Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device is based on STV0903 demodulator, STB6100 tuner
and CX23885 chipset; subsystem id: 8000:3034
This is a modified version of the official Prof Tuners Group patch:
http://www.proftuners.com/sites/default/files/prof8000_0.patch
[mchehab@redhat.com: trivial merge conflict fixup]
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Netup cards revision 1 are not manufactured anymore.
So, rev. 4 should be default.
Signed-off-by: Anton Nurkin <ptqa@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all PCI drivers with their own directory under
drivers/media/video into drivers/media/pci and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
