Commit Graph

11 Commits

Author SHA1 Message Date
Jason Cooper
93fff4ce19 ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
When DT support for kirkwood was first introduced, there was no clock
infrastructure.  As a result, we had to manually pass the
clock-frequency to the driver from the device node.

Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.

The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.

Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.

Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.

Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-03-08 21:32:52 +00:00
Thomas Petazzoni
a49da46c52 arm: kirkwood: dreamplug: use Device Tree to probe SDIO
Now that the mvsdio driver has a Device Tree binding, and the SDIO
controller is declared in kirkwood.dtsi, migrate the dreamplug board
to use the Device Tree to probe the SDIO controller and to mux this
interface properly.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-02-28 18:57:10 +01:00
Andrew Lunn
56942287be ARM: Kirkwood: Convert dreamplug to pinctrl.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-11-24 02:58:11 +00:00
Andrew Lunn
b94a257cdb ARM: Kirkwood: Describe Dreamplug LEDs in DT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
2012-07-27 16:50:41 +02:00
Andrew Lunn
2cef1a2853 ARM: Kirkwood: Use DT to configure SATA device.
Convert boards using DT, but the old way of configuring SATA to now
use properties in there DT file.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
2012-07-27 16:49:29 +02:00
Michael Walle
be2aa95675 ARM: kirkwood: use devicetree for SPI on dreamplug
Use the device tree for the SPI driver and partition layout.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
2012-07-27 16:49:21 +02:00
Andrew Lunn
778435045a ARM: Kirkwood: Replace mrvl with marvell
It has been decided to use marvell, not mrvl, in the compatibility
property. Search & replace.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
2012-07-25 17:06:23 +02:00
Jason Cooper
163f2cea67 ARM: kirkwood: fdt: define uart[01] as disabled, enable uart0
Define both uarts in kirkwood.dtsi as they are common to all kirkwood
SoCs.  Each board may enable all or none of them, so they are disabled
by default.  uart0 is enabled for the dreamplug.

tclk can vary for each board, so we leave it undefined in the kirkwood
dtsi.  Each board can then set it as appropriate when enabling the uart.

Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-03-16 04:28:42 +00:00
Jason Cooper
b77816dea3 ARM: kirkwood: fdt: use mrvl ticker symbol
Also, use inclusive register size for uart0.

Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-03-16 04:28:41 +00:00
Jason Cooper
759a45185a ARM: kirkwood: convert uart0 to devicetree.
This uart is the primary console for the dreamplug.  Removed
kirkwood_uart0_init() call from board-dt.c.

Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-02-27 16:21:44 +00:00
Jason Cooper
3d468b6d60 ARM: kirkwood: add dreamplug (fdt) support.
Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.

After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support.  First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.

Driver porting will start with the uart (see next patch), and progress
from there.  Possibly, spi/flash/partitions will be next.

When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.

Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-02-27 16:21:40 +00:00