Globally update my email address in six files scattered through the
tree.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
- Clean up and rework the PM QoS API to simplify the code and
reduce the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370
and similar platforms where the USB plug/unplug events are
handled by the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to
run on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate driver
and update its documentation (Rafael Wysocki, Alex Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file
and use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result (Leonard
Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level
PM QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences
in a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies).
-----BEGIN PGP SIGNATURE-----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=cBQd
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These clean up and rework the PM QoS API, address a suspend-to-idle
wakeup regression on some ACPI-based platforms, clean up and extend a
few cpuidle drivers, update multiple cpufreq drivers and cpufreq
documentation, and fix a number of issues in devfreq and several other
things all over.
Specifics:
- Clean up and rework the PM QoS API to simplify the code and reduce
the size of it (Rafael Wysocki).
- Fix a suspend-to-idle wakeup regression on Dell XPS13 9370 and
similar platforms where the USB plug/unplug events are handled by
the EC (Rafael Wysocki).
- CLean up the intel_idle and PSCI cpuidle drivers (Rafael Wysocki,
Ulf Hansson).
- Extend the haltpoll cpuidle driver so that it can be forced to run
on some systems where it refused to load (Maciej Szmigiero).
- Convert several cpufreq documents to the .rst format and move the
legacy driver documentation into one common file (Mauro Carvalho
Chehab, Rafael Wysocki).
- Update several cpufreq drivers:
* Extend and fix the imx-cpufreq-dt driver (Anson Huang).
* Improve the -EPROBE_DEFER handling and fix unwanted CPU
overclocking on i.MX6ULL in imx6q-cpufreq (Anson Huang,
Christoph Niedermaier).
* Add support for Krait based SoCs to the qcom driver (Ansuel
Smith).
* Add support for OPP_PLUS to ti-cpufreq (Lokesh Vutla).
* Add platform specific intermediate callbacks support to
cpufreq-dt and update the imx6q driver (Peng Fan).
* Simplify and consolidate some pieces of the intel_pstate
driver and update its documentation (Rafael Wysocki, Alex
Hung).
- Fix several devfreq issues:
* Remove unneeded extern keyword from a devfreq header file and
use the DEVFREQ_GOV_UPDATE_INTERNAL event name instead of
DEVFREQ_GOV_INTERNAL (Chanwoo Choi).
* Fix the handling of dev_pm_qos_remove_request() result
(Leonard Crestez).
* Use constant name for userspace governor (Pierre Kuo).
* Get rid of doc warnings and fix a typo (Christophe JAILLET).
- Use built-in RCU list checking in some places in the PM core to
avoid false-positive RCU usage warnings (Madhuparna Bhowmik).
- Add explicit READ_ONCE()/WRITE_ONCE() annotations to low-level PM
QoS routines (Qian Cai).
- Fix removal of wakeup sources to avoid NULL pointer dereferences in
a corner case (Neeraj Upadhyay).
- Clean up the handling of hibernate compat ioctls and fix the
related documentation (Eric Biggers).
- Update the idle_inject power capping driver to use variable-length
arrays instead of zero-length arrays (Gustavo Silva).
- Fix list format in a PM QoS document (Randy Dunlap).
- Make the cpufreq stats module use scnprintf() to avoid potential
buffer overflows (Takashi Iwai).
- Add pm_runtime_get_if_active() to PM-runtime API (Sakari Ailus).
- Allow no domain-idle-states DT property in generic PM domains (Ulf
Hansson).
- Fix a broken y-axis scale in the intel_pstate_tracer utility (Doug
Smythies)"
* tag 'pm-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (78 commits)
cpufreq: intel_pstate: Simplify intel_pstate_cpu_init()
tools/power/x86/intel_pstate_tracer: fix a broken y-axis scale
ACPI: PM: s2idle: Refine active GPEs check
ACPICA: Allow acpi_any_gpe_status_set() to skip one GPE
PM: sleep: wakeup: Skip wakeup_source_sysfs_remove() if device is not there
PM / devfreq: Get rid of some doc warnings
PM / devfreq: Fix handling dev_pm_qos_remove_request result
PM / devfreq: Fix a typo in a comment
PM / devfreq: Change to DEVFREQ_GOV_UPDATE_INTERVAL event name
PM / devfreq: Remove unneeded extern keyword
PM / devfreq: Use constant name of userspace governor
ACPI: PM: s2idle: Fix comment in acpi_s2idle_prepare_late()
cpufreq: qcom: Add support for krait based socs
cpufreq: imx6q-cpufreq: Improve the logic of -EPROBE_DEFER handling
cpufreq: Use scnprintf() for avoiding potential buffer overflow
cpuidle: psci: Split psci_dt_cpu_init_idle()
PM / Domains: Allow no domain-idle-states DT property in genpd when parsing
PM / hibernate: Remove unnecessary compat ioctl overrides
PM: hibernate: fix docs for ioctls that return loff_t via pointer
Documentation: intel_pstate: update links for references
...
With the latest cleanup in qcom scm driver the secure monitor
call for setting the remote processor state returns EINVAL when
it is called for the first time and after another scm call
auth_and_reset. The error returned from scm call could be ignored
because the state transition is already done in auth_and_reset.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mt8173 VPU firmware has been moved to a sub-folder of
linux-firmware, so load vpu-fw from the new location first,
if it fails, then from the old one.
Signed-off-by: Rui Wang <gtk_ruiwang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix build fault when CONFIG_HWMON is a module, and CONFIG_VIDEO_I2C
as builtin. This is due to 'imply hwmon' in the respective Kconfig.
Issue build log:
ld: drivers/media/i2c/video-i2c.o: in function `amg88xx_hwmon_init':
video-i2c.c:(.text+0x2e1): undefined reference to `devm_hwmon_device_register_with_info
Cc: rdunlap@infradead.org
Fixes: acbea67989 (media: video-i2c: add hwmon support for amg88xx)
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The initial physical address was one too low for the outputs.
E.g. if 1.0.0.0 was expected, then it was set to 0.0.0.0, and
2.0.0.0 became 1.0.0.0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Johan Korsnes <johan.korsnes@gmail.com>
Fixes: 4ee895e71a ("media: vivid: reorder CEC allocation and control set-up")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This function is no longer used by other drivers, so it can be
made static.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This argument refers to a stable name for an HDMI port, mostly i915
(ACPI) specific. Since we'll be introducing a more generic 'name' argument
as well later, rename this now to avoid confusion.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch makes use of to_vpfe() to get a pointer to vpfe_device
Signed-off-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The new format is called V4L2_PIX_FMT_Y14. Like V4L2_PIX_FMT_Y10 and
V4L2_PIX_FMT_Y12 it is stored in two bytes per pixel but has only two
unused bits at the top.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Check the return value of of_clk_get and print an error
message if not EPROBE_DEFER.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change stm32-cec driver to not print an error message when the
device probe operation is deferred.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change stm32-cec driver to defer probe when auxiliary clock
"hdmi-cec" is registered in the system not has not been probed yet.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity check in cit_get_packet_size() is not redundant as
the driver is mixing looking up altsettings by index and by number,
which may not coincide.
Fixes: 659fefa0eb ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01")
Fixes: 59f8b0bf3c ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity checks in stv06xx_start() and pb0100_start() are
not redundant as the driver is mixing looking up altsettings by index
and by number, which may not coincide.
Fixes: 8668d504d7 ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor")
Fixes: c0b33bdc5b ("[media] gspca-stv06xx: support bandwidth changing")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make sure to check that we have at least one endpoint before accessing
the endpoint array to avoid dereferencing a NULL-pointer on stream
start.
Note that these sanity checks are not redundant as the driver is mixing
looking up altsettings by index and by number, which need not coincide.
Fixes: 1876bb923c ("V4L/DVB (12079): gspca_ov519: add support for the ov511 bridge")
Fixes: b282d87332 ("V4L/DVB (12080): gspca_ov519: Fix ov518+ with OV7620AE (Trust spacecam 320)")
Cc: stable <stable@vger.kernel.org> # 2.6.31
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As of `s5c73m3.h` the auto focus cluster in `s5c73m3_ctrls` has 5 and not 6
controls.
Signed-off-by: Sebastian Gross <sebastian.gross@emlix.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This dprintk is supposed to be informational, not an error. Set it to
the same level as the other messages related to memory allocations so
the kernel log does not get filled by messages during normal operation.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pad is now checked by v4l2_subdev_call_wappers
call_g_frame_interval-> check_frame_interval-> check_pad
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the
reset pin is active low and the DT binding defines the pin as active
low, which means that the values set by the driver are inverted and thus
the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high,
which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but
regulator_bulk_enable() API enables all the regulators asynchronously.
Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the
bulk API does not give any guarantee about the order of regulators,
change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C
transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
recommended by the vendor. Fix this as well.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support
for RAW8 bayer format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.
The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While upgrading from 5.5.2 -> 5.5.6 I was surprised by:
ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe':
tvp5150.c:(.text+0x11ac): undefined reference to
`__devm_regmap_init_i2c'
make: *** [Makefile:1078: vmlinux] Error 1
The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C
And a quick grep showed that it was needed by more targets.
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The debug output for tvp5150_selmux() isn't really intuitive. Register
values are printed decimal formatted and the input/output driver states
are printed as enum. Even more the "normal" output enum mapps to zero so
a active output will printing output=0 and a inactive output=1.
Change this by brinting the register values hex formatted and the states
as more readable string.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The tvp5150 accepts NTSC(M,J,4.43), PAL (B,D,G,H,I,M,N) and SECAM video
data and is able to auto-detect the input signal. The auto-detection
does not work if the connector does not receive an input signal and the
tvp5150 might not be configured correctly. This misconfiguration leads
into wrong decoded video streams if the tvp5150 gets powered on before
the video signal is present.
Limit the supported sdtv standards according to the actual selected
connector to avoid a misconfiguration.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Bring the device into a working state upon a open/close call. Currently
this involves only the interrupt enable/disable process but can be
extended in the future.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the driver notifies internal subdevs if the signal is locked
or not. This information is also useful for userpace applications e.g. to
switch to another input device upon a signal lost event.
This commit adds the support for the userspace to subscribe to the
V4L2_EVENT_SOURCE_CHANGE and V4L2_EVENT_CTRL events.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As documented in [1] the runtime-pm ops are used to set the device into
a fully 'workable' state. Therefore it can be used to enable or disable
the irqs.
[1] https://www.kernel.org/doc/html/latest/power/runtime_pm.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several debug prints in the tvp5150_parse_dt() function, which
do not print the prefix, because the v4l2_subdev is not initialized, yet.
Initialize the v4l2_subdev before parsing the device tree to fix the
debug messages.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 10d5509c8d ("[media] v4l2: remove g/s_crop from video ops")
the 'which' field for set/get_selection must be FORMAT_ACTIVE. There is
no way to try different selections. The patch adds a helper function to
select the correct selection memory space (sub-device file handle or
driver state) which will be set/returned.
The selection rectangle is updated if the format is FORMAT_ACTIVE and
the rectangle position and/or size differs from the current set
rectangle.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently a local copy of sel->r is made and adapted to the hardware
constraints. After the adaption the value is applied to the hardware but
the driver forgot to reflect the adapted value to the user space.
Drop the local copy and work directly on the requested rectangle
instead to fix this.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds the of_graph support to describe the tvp input connections.
Physical the TVP5150 has three ports: AIP1A, AIP1B and YOUT. As result
of discussion [1],[2] the device-tree maps these ports 1:1. Look at the
Documentation for more information. Since the TVP5150 is a converter/bridge
the device-tree must contain at least 1-input and 1-output port. The
mc-connectors and mc-links are only created if the device-tree contains the
corresponding connector nodes. If more than one connector is available the
media_entity_operations.link_setup() callback ensures that only one
connector is active.
[1] https://www.spinics.net/lists/linux-media/msg138545.html
[2] https://www.spinics.net/lists/linux-media/msg138546.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit f7b4b54e63 ("[media] tvp5150: add HW input connectors support")
added input signals support for the tvp5150, but the approach was found
to be incorrect so the corresponding DT binding commit 82c2ffeb21
("[media] tvp5150: document input connectors DT bindings") was reverted.
This left the driver with an undocumented (and wrong) DT parsing logic,
so lets get rid of this code as well until the input connectors support
is implemented properly.
It's a partial revert due other patches added on top of mentioned commit
not allowing the commit to be reverted cleanly anymore. But all the code
related to the DT parsing logic and input entities creation are removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[m.felsch@pengutronix.de: rm TVP5150_INPUT_NUM define]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The patch adds the initial connector parsing code, so we can move from a
driver specific parsing code to a generic one. Currently only the
generic fields and the analog-connector specific fields are parsed. Parsing
the other connector specific fields can be added by a simple callbacks.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[hverkuil-cisco@xs4all.nl: replace ; with break; in a empty case]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A link is between two endpoints not between two ports to be more
precise. Add the local_id/remote_id field which stores the endpoint
reg/port property to the link. Now the link holds all necessary
information about a link.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This helper was introduced before those helpers where awailable. Convert
it to cleanup the code and improbe readability.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the driver differentiate the port number property handling for
ACPI and DT. This is wrong as because ACPI should use the "reg" val too
[1].
[1] https://patchwork.kernel.org/patch/11421985/
Fixes: ca50c197bd ("[media] v4l: fwnode: Support generic fwnode for parsing standardised properties")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When calling ccdc_data_size_max_bit() to validate data_sz in
vpfe_ccdc_validate_param(), it's treated as an enumeration ranging from
0 to 7 while essentially it's an 32 bit unsigned integer directly from
user space. This can make the return value of ccdc_data_size_max_bit()
underflow and bypass the following check.
To fix this, an additional check is added to the following if clause to
keep this enumaration variable in range. And if its value is not legal,
return -EINVAL properly.
Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the switch to use v4l2_async_notifier_add_subdev() and
v4l2_async_notifier_cleanup(), unloading the ti_cal module would cause a
kernel oops.
This was root cause to the fact that v4l2_async_notifier_cleanup() tries
to kfree the asd pointer passed into v4l2_async_notifier_add_subdev().
In our case the asd reference was from a statically allocated struct.
So in effect v4l2_async_notifier_cleanup() was trying to free a pointer
that was not kalloc.
So here we switch to using a kzalloc struct instead of a static one.
To achieve this we re-order some of the calls to prevent asd allocation
from leaking.
Fixes: d079f94c90 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Cc: stable@vger.kernel.org
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Previously, vpu->recv_buf and send_buf are forced cast from
void __iomem *tcm. vpu->recv_buf->share_buf is passed to
vpu_ipi_desc.handler(). It's not able to do unaligned access. Otherwise
kernel would crash due to unable to handle kernel paging request.
struct vpu_run {
u32 signaled;
char fw_ver[VPU_FW_VER_LEN];
unsigned int dec_capability;
unsigned int enc_capability;
wait_queue_head_t wq;
};
fw_ver starts at 4 byte boundary. If system enables
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS, strscpy() will do
read_word_at_a_time(), which tries to read 8-byte: *(unsigned long *)addr
vpu_init_ipi_handler() calls strscpy(), which would lead to crash.
vpu_init_ipi_handler() and several other handlers (eg.
vpu_dec_ipi_handler) only do read access to this data, so they can be
const, and we can use memcpy_fromio() to copy the buf to another non iomem
buffer then pass to handler.
Fixes: 85709cbf15 ("media: replace strncpy() by strscpy()")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add encoder control for enabling/disabling frame rate control via
V4L2_CID_MPEG_VIDEO_FRAME_RC_ENABLE. It is enabled by default.
Signed-off-by: Jeffrey Kardatzke <jkardatzke@google.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes the following smatch warning in the error path:
drivers/media/platform/qcom/venus/vdec.c:968 vdec_start_streaming()
warn: inconsistent returns 'mutex:&inst->lock'.
Locked on: line 952
Unlocked on: line 963
line 968
by goto mutex unlock.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The variable gate is being initialized and also checked and re-assigned
with values that are never read as it is being re-assigned later in a
for-loop with a new value. The assignments are redundant and can be
removed.
Addresses Coverity ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The shifting of buf[3] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. In
the unlikely event that the the top bit of buf[3] is set then all
then all the upper bits end up as also being set because of
the sign-extension and this affect the ev->post_bit_error sum.
Fix this by using the temporary u32 variable bit_error to avoid
the sign-extension promotion. This also removes the need to do the
computation twice.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 267897a470 ("[media] tda10071: implement DVBv5 statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is required to support the Terratec S2 USB Box Revision 4, which
reused usb vid:pid, but has a different demodulator (m88ds3103b) at
i2c address 0x6a.
[fixed checkpatch issues]
Signed-off-by: Michael Bunk <micha@freedict.org>
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
