Add field definitions for some of the 64-bit specific Hardware page
Table Walker (HTW) register fields in PWSize and PWCtl, in preparation
for fixing the 64-bit HTW configuration.
Also print these fields out along with the others in print_htw_config().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simplify the DSP instruction wrapper macros which use explicit encodings
for microMIPS and normal MIPS by using the new encoding macros and
removing duplication.
To me this makes it easier to read since it is much shorter, but it also
ensures .insn is used, preventing objdump disassembling the microMIPS
code as normal MIPS.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13314/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hardcoded MIPS instruction encodings are provided for tlbinvf, mfhc0 &
mthc0 instructions, but microMIPS encodings are missing. I doubt any
microMIPS cores exist at present which support these instructions, but
the microMIPS encodings exist, and microMIPS cores may support them in
the future. Add the missing microMIPS encodings using the new macros.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13313/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Toolchains may be used which support microMIPS but not VZ instructions
(i.e. binutis 2.22 & 2.23), so extend the explicitly encoded versions of
the guest COP0 register & guest TLB access macros to support microMIPS
encodings too, using the new macros.
This prevents non-microMIPS instructions being executed in microMIPS
mode during CPU probe on cores supporting VZ (e.g. M5150), which cause
reserved instruction exceptions early during boot.
Fixes: bad50d7925 ("MIPS: Fix VZ probe gas errors with binutils <2.24")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13311/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To allow simplification of macros which use inline assembly to
explicitly encode instructions, add a few simple abstractions to
mipsregs.h which expand to specific microMIPS or normal MIPS encodings
depending on what type of kernel is being built:
_ASM_INSN_IF_MIPS(_enc) : Emit a 32bit MIPS instruction if microMIPS is
not enabled.
_ASM_INSN32_IF_MM(_enc) : Emit a 32bit microMIPS instruction if enabled.
_ASM_INSN16_IF_MM(_enc) : Emit a 16bit microMIPS instruction if enabled.
The macros can be used one after another since the MIPS / microMIPS
macros are mutually exclusive, for example:
__asm__ __volatile__(
".set push\n\t"
".set noat\n\t"
"# mfgc0 $1, $%1, %2\n\t"
_ASM_INSN_IF_MIPS(0x40610000 | %1 << 11 | %2)
_ASM_INSN32_IF_MM(0x002004fc | %1 << 16 | %2 << 11)
"move %0, $1\n\t"
".set pop"
: "=r" (__res)
: "i" (source), "i" (sel));
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13310/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The versions of the __write_{32,64}bit_gc0_register() macros for when
there is no virt support in the assembler use the "J" inline asm
constraint to allow integer zero, but this needs to be accompanied by
the "z" formatting string so that it turns into $0. Fix both macros to
do this.
Fixes: bad50d7925 ("MIPS: Fix VZ probe gas errors with binutils <2.24")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13289/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SegCtl registers are standard for MIPSr3..MIPSr5. Add definitions of
these registers and use them rather than constants
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13290/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The VZ guest register & TLB access macros introduced in commit "MIPS:
Add guest CP0 accessors" use VZ ASE specific instructions that aren't
understood by versions of binutils prior to 2.24.
Add a check for whether the toolchain supports the -mvirt option,
similar to the MSA toolchain check, and implement the accessors using
.word if not.
Due to difficulty in converting compiler specified registers (e.g. "$3")
to usable numbers (e.g. "3") in inline asm, we need to copy to/from a
temporary register, namely the assembler temporary (at/$1), and specify
guest CP0 registers numerically in the gc0 macros.
Fixes: 7eb9111822 ("MIPS: Add guest CP0 accessors")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-next@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13255/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add guest CP0 accessors and guest TLB operations along the same lines as
the existing macros and functions for the root CP0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13229/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add various register definitions to <asm/mipsregs.h> for the coprocessor
zero registers in the VZ ASE, namely CP0_GuestCtl0, CP0_GuestCtl0Ext,
CP0_GuestCtl1, CP0_GuestCtl2, CP0_GuestCtl3, and CP0_GTOffset.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13228/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The decode_config4() function reads kscratch_mask from
CP0_Config4.KScrExist using a hard coded shift and mask. We already have
a definition for the mask in mipsregs.h, so add a definition for the
shift and make use of them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13227/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CP0_[X]ContextConfig registers are present if CP0_Config3.CTXTC or
CP0_Config3.SM are set, and provide more control over which bits of
CP0_[X]Context are set to the faulting virtual address on a TLB
exception.
KVM/VZ will need to be able to save and restore these registers in the
guest context, so add the relevant definitions and probing of the
ContextConfig feature in the root context first.
[ralf@linux-mips.org: resolve merge conflict.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13225/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The optional CP0_BadInstr and CP0_BadInstrP registers are written with
the encoding of the instruction that caused a synchronous exception to
occur, and the prior branch instruction if in a delay slot.
These will be useful for instruction emulation in KVM, and especially
for VZ support where reading guest virtual memory is a bit more awkward.
Add CPU option numbers and cpu_has_* definitions to indicate the
presence of each registers, and add code to probe for them using bits in
the CP0_Config3 register.
[ralf@linux-mips.org: resolve merge conflict.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13224/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CP0_EBase register may optionally have a write gate (WG) bit to
allow the upper bits to be written, i.e. bits 31:30 on MIPS32 since r3
(to allow for an exception base outside of KSeg0/KSeg1 when segmentation
control is in use) and bits 63:30 on MIPS64 (which also implies the
extension of CP0_EBase to 64 bits long).
The presence of this feature will need to be known about for VZ support
in order to correctly save and restore all the bits of the guest
CP0_EBase register, so add CPU feature definition and probing for this
feature.
Probing the WG bit on MIPS64 can be a bit fiddly, since 64-bit COP0
register access instructions were UNDEFINED for 32-bit registers prior
to MIPS r6, and it'd be nice to be able to probe without clobbering the
existing state, so there are 3 potential paths:
- If we do a 32-bit read of CP0_EBase and the WG bit is already set, the
register must be 64-bit.
- On MIPS r6 we can do a 64-bit read-modify-write to set CP0_EBase.WG,
since the upper bits will read 0 and be ignored on write if the
register is 32-bit.
- On pre-r6 cores, we do a 32-bit read-modify-write of CP0_EBase. This
avoids the potentially UNDEFINED behaviour, but will clobber the upper
32-bits of CP0_EBase if it isn't a simple sign extension (which also
requires us to ensure BEV=1 or modifying the exception base would be
UNDEFINED too). It is hopefully unlikely a bootloader would set up
CP0_EBase to a 64-bit segment and leave WG=0.
[ralf@linux-mips.org: Resolved merge conflict.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13223/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add definitions for the bits & fields in the CP0_EBase register, and use
them from a few different places in arch/mips which hardcoded these
values.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add definitions for the ASID field in CP0_EntryHi (along with the soon
to be used ASIDX field), and use them in a few previously hardcoded
cases.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13205/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3A R2 has pwbase/pwfield/pwsize/pwctl registers in CP0 (this
is very similar to HTW) and lwdir/lwpte/lddir/ldpte instructions which
can be used for fast TLB refill.
[ralf@linux-mips.org: Resolve conflict.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-2 has a 4 entry itlb which is a subset of jtlb, Loongson-3 has
a 4 entry itlb and a 4 entry dtlb which are subsets of jtlb. We should
write diag register to invalidate itlb/dtlb when flushing jtlb because
itlb/dtlb are not totally transparent to software.
For Loongson-3A R2 (and newer), we should invalidate ITLB, DTLB, VTLB
and FTLB before we enable/disable FTLB.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Steven J . Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12753/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The files watch.c and ptrace.c contain various magic masks for
WatchLo/WatchHi register fields. Add some definitions to mipsregs.h for
these registers and make use of them in both watch.c and ptrace.c,
hopefully making them more readable.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12729/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
do_watch() clears bit 22 of cause without using a CAUSEF_* definition
from mipsregs.h. Add a definition for this bit (CAUSEF_WP) and make use
of it. Also use clear_c0_cause() instead of manual read/modify/write.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12728/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPSr6 introduces support for "Virtual Processors", which are
conceptually similar to VPEs from the now-deprecated MT ASE. Detect
whether the system supports VPs using the VP bit in Config5, adding
cpu_has_vp for use by later patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Maciej W. Rozycki <macro@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12327/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a few missing trap codes.
[ralf@linux-mips.org: Drop removal of exception codes. I don't care what
the incomplete architecture spec says; it can't change existing hardware
and VCEI is supported indeed.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11890/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the Cause.ExcCode trap code definitions from kvm_host.h to
mipsregs.h, since they describe architectural bits rather than KVM
specific constants, and change the prefix from T_ to EXCCODE_.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11891/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CAUSEB_DC and CAUSEF_DC definitions used by KVM are defined in
asm/kvm_host.h, but all the other Cause register field definitions are
found in asm/mipsregs.h.
Lets reunite the DC bit definitions with its friends in mipsregs.h.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11885/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tidy up the definition of the EntryLo RI & XI bits using BITS_PER_LONG
rather than #ifdef'ing on CONFIG_64BIT, and add a definition for the
offset to the PFN field for use by a later patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Provide support for outputting early debug information, in the form of
various register values should an exception occur, during the early
bringup of secondary cores. This code requires an ns16550-compatible
UART accessible from the secondary core, and is written in assembly due
to the environment in which such early exceptions occur where way may
not have a stack, be coherent or even have initialised caches.
[ralf@linux-mips.org: Fix merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11202/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the definition in locore.S and move a few of the other similar
definitions in asm/mipsregs.h too. CP0_INTCTL, CP0_SRSCTL, & CP0_SRSMAP
are unused so they're just dropped instead. CP0_DDATA_LO is left where
it is as I have patches to eliminate its use in locore.S and it
otherwise is unlikely to need to be used from assembly code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add cpu_has_ftlb, which specifies that an FTLB is present in addition to
the VTLB, probed based on whether Config.MT == 4 (rather than 1 for
standard JTLB).
This is necessary since MIPS release 6 removes Config4.MMUExtDef, so the
presence of the FTLB fields in Config4 must be determined from Config.MT
instead.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11159/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic field definitions (i.e. present before MIPS32/MIPS64) in
mipsregs.h are conventionally not prefixed with MIPS_, so rename the
recently added MIPS_ENTRYLO_* definitions for the G, V, D, and C fields
to ENTRYLO_*. Also rearrange to put the EntryLo and EntryHi definitions
in the right place in the file.
Fixes: 8ab6abcb6a ("MIPS: mipsregs.h: Add EntryLo bit definitions")
Reported-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10725/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These are bitfields and treating them as signed values doesn't make
any sense.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Chris Packham <judge.packham@gmail.com>
Update __read_32bit_c0_register() and __read_32bit_c0_ctrl_register() to
use "unsigned int res;" instead of "int res;". There is little reason to
treat these register values as signed. They are either counters (which
by definition are unsigned) or are made up of various bit fields to be
interpreted as per the CPU datasheet.
This has come up via u-boot[1] which sync's asm/mipsregs.h with the
kernel. In u-boots case the value read from read_c0_count() is assigned
to an unsigned long [2] which triggers a sign extension and causes a
bug.
U-boot should probably be more explicit about the types used for the
timer_read_counter() API but that aside is there any reason to treat
these values as signed integers? A quick grep around the arch/mips makes
me thing that there may be some bugs lurking when read_c0_count() starts
to yield a negative value but I haven't really explored any of them.
[1] - http://lists.denx.de/pipermail/u-boot/2015-July/219086.html
[2] - http://git.denx.de/?p=u-boot.git;a=blob;f=arch/mips/cpu/time.c#l11
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/10718/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The R12000 added a new feature to enhance branch prediction called
"global history". Per the Vr10000 Series User Manual (U10278EJ4V0UM),
Coprocessor 0, Diagnostic Register (22):
"""
If bit 26 is set, branch prediction uses all eight bits of the global
history register. If bit 26 is not set, then bits 25:23 specify a count
of the number of bits of global history to be used. Thus if bits 26:23
are all zero, global history is disabled.
The global history contains a record of the taken/not-taken status of
recently executed branches, and when used is XOR'ed with the PC of a
branch being predicted to produce a hashed value for indexing the BPT.
Some programs with small "working set of conditional branches" benefit
significantly from the use of such hashing, some see slight performance
degradation.
"""
This patch enables global history on R12000 CPUs and up by setting bit
26 in the branch prediction diagnostic register (CP0 $22) to '1'. Bits
25:23 are left alone so that all eight bits of the global history
register are available for branch prediction.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add definitions for EntryLo register bits in mipsregs.h. The R4000
compatible ones are prefixed MIPS_ENTRYLO_ and the R3000 compatible ones
are prefixed R3K_ENTRYLO_.
These will be used in later patches.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/10073/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Define IEEE 754-2008 feature control bits: FIR.HAS2008, FCSR.ABS2008 and
FCSR.NAN2008, and update the `_ieee754_csr' structure accordingly.
For completeness define FIR.UFRP too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9709/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement the FCCR, FEXR and FENR "shadow" FPU registers for the
architecture levels that include them, for the CFC1 and CTC1
instructions in the full emulation mode.
For completeness add macros for the CP1 UFR and UNFR registers too, no
actual implementation though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reindent CP0 Cause macros for a single space after #define, leaving
extra indentation for individual Interrupt Pending bits as with CP0
Status register's Interrupt Mask bits.
[ralf@linux-mips.org: Fix conflict.]
[ralf@linux-mips.org: Fix indentation of the CAUSEB_FDCI and CAUSEF_FDCI
definitions.]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9669/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX39 CP0 Configuration Register 3 macro definitions have been randomly
thrown in the middle of a block of CP0 Status register value macros.
Move them to the end of the whole CP0 register value macro block,
complementing the location of the TX39 Cache register name macro at the
end of the CP0 register name macro block.
[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9668/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Originally CP1 macros were placed between CP0 register name macros and
CP0 register value macros. As changes were applied to the header the
position of CP1 macros gradually has become more and more arbitrary and
two separate blocks were created. This may only cause confusion.
Move them out of the way then and place together after all the CP0
macros. No semantic change.
[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9667/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove a duplicate FPU Status Register reference that has been there
since forever and a mistakenly copied and pasted R4xx0 manual reference.
[ralf@linux-mips.org: Fix conflict.]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9666/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add architectural field definitions relating to the Fast Debug Channel
(FDC) interrupt, namely the pending bit in Cause and the field in
IntCtl to specify which CPU IRQ line the FDC interrupt is routed to.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9139/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add architectural definitions and probing for the MIPS Common Device
Memory Map (CDMM) region. When supported and enabled at a particular
physical address, this region allows some number of per-CPU devices to
be discovered and controlled via MMIO.
A bit exists in Config3 to determine whether the feature is present, and
a CDMMBase CP0 register allows the region to be enabled at a particular
physical address.
[ralf@linux-mips.org: Sort conflict with other patches.]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/9178/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
If Config5/LLB is set in the core, then software can write the LLB
bit in the LLADDR register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The LLBIT (bit 4) in the Config5 CP0 register indicates the software
availability of the Load-Linked bit. This bit is only set by hardware
and it has the following meaning:
0: LLB functionality is not supported
1: LLB functionality is supported. The following feature are also
supported:
- ERETNC instruction. Similar to ERET but it does not clear the LLB
bit in the LLAddr register.
- CP0 LLAddr/LLB bit must be set
- LLbit is software accessible through the LLAddr[0]
This will be used later on to emulate R2 LL/SC instructions.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Add a write_32bit_cp1_register() macro to compliment the
read_32bit_cp1_register() macro. This is to abstract whether .set
hardfloat needs to be used based on GAS_HAS_SET_HARDFLOAT.
The implementation of _read_32bit_cp1_register() .sets mips1 due to
failure of gas v2.19 to assemble cfc1 for Octeon (see commit
25c3000300 ("MIPS: Override assembler target architecture for
octeon.")). I haven't copied this over to _write_32bit_cp1_register() as
I'm uncertain whether it applies to ctc1 too, or whether anybody cares
about that version of binutils any longer.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9172/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
Add read/write macros to access the upper bits of the
extended EntryLo0 and EntryLo1 registers used by XPA.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8455/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
