According the JEDEC specification an eMMC card supporting 1.8V vccq in DDR
mode should also be capable of 3.3V. However, it's been reported that some
mmc hosts supports 3.3V, but not 1.8V.
Currently the mmc core implements an error handling when the host fails to
set 1.8V for vccq, by falling back to 3.3V. Unfortunate, this seems to be
insufficient for some mmc hosts. To enable these to use eMMC DDR mode let's
invent a new mmc cap, MMC_CAP_3_3V_DDR, which tells whether they support
the eMMC 3.3V DDR mode.
In case MMC_CAP_3_3V_DDR is set, but not MMC_CAP_1_8V_DDR, let's change to
remain on the 3.3V, as it's the default voltage level for vccq, set by the
earlier power up sequence.
As this change introduces MMC_CAP_3_3V_DDR, let's take the opportunity to
do some re-formatting of the related defines in the header file.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Earlier the mmc_set_signal_voltage() existed, but since it has been renamed
to mmc_set_uhs_voltage(), we can now use that name instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. To clarify this let's do the following changes.
- We are always providing MMC_SIGNAL_VOLTAGE_180 as the signal_voltage
parameter to the function. Then, let's just remove the parameter as it
serves no purpose.
- Rename the function to mmc_set_uhs_voltage().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
The mmc_set_signal_voltage() function is used for SD/SDIO when switching to
1.8V for UHS mode. Therefore let's remove the redundant code dealing with
MMC_SIGNAL_VOLTAGE_330.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jan Glauber <jglauber@cavium.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Some controllers have 2 clock sources instead of 1. The 2nd clock
is for the internal card detect logic and must be enabled/disabled
along with the main core clock for proper operation.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cleanup some debug prints that cause needless noise
during normal usage.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_blk_issue_rq() function is called in exactly one place
in queue.c and there the return value is ignored. So the
functions called from that function that also meticulously
return 0/1 do so for no good reason.
Error reporting on the asynchronous requests are done upward to
the block layer when the requests are eventually completed or
fail, which may happen during the flow of the mmc_blk_issue_*
functions directly (for "special commands") or later, when an
asynchronous read/write request is completed.
The issuing functions do not give rise to errors on their own,
and there is nothing to return back to the caller in queue.c.
Drop all return values and make the function return void.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recycling the same variable in an x=x+1 fashion may seem
clever here but it makes the code terse and hard to follow
for humans. Introduce a new_areq and old_areq variable so
we see what is going on.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting rqc to NULL followed by a goto to cmd_abort is just a way
to do unconditional abort without starting any new command.
Inline the calls to mmc_blk_rw_cmd_abort() and return immediately
in those cases.
Add some comments to the code flow so it is clear that this is
where the asynchronous requests come back in and the result of
them gets handled.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code in mmc_blk_issue_rq_rq() aborts a command if the request
is not properly aligned on large sectors. As part of the path
jumping out, it assigns the local variable mq_rq reflecting
a MMC queue request to the current MMC queue request, which is
confusing since the variable is not used after this jump.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a step toward breaking apart the very complex function
mmc_blk_issue_rw_rq() we break out the code to start a new
request.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a first step toward breaking apart the very complex function
mmc_blk_issue_rw_rq() we break out the command abort code.
This code assumes "ret" is != 0 and then repeatedly hammers
blk_end_request() until the request to the block layer to end
the request succeeds.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the bitops API instead of shifting directly.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the sdhci-s3c-regs.h file.
Instead, it located those defined values into sdhci-s3c.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Before enabling SDIO irqs, clear the status bit, so we discard old and
stale interrupts. Needed to get two wireless cards working. Use the
newly introduced macro in all places.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
QUIRK sounds like there is something wrong, but actually there are just
some bits which need to be 1. Rename it to be more clear.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_sdio_irq() is not used as a seperate irq handler anymore, so we
can make it similar to the other irq helper functions, namely:
* only give the host as argument function which is what it really needs
* prefix function name with __
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow power sequencing for the Marvell SD8787 Wifi/BT chip.
This can be abstracted to other chipsets if needed in the future.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Create a helper function to disable clocks and use it in remove(), too.
Now, clk_summary in debugfs reports the clocks as disabled and
unprepared after unbinding.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This provides enhanced_strobe mode feature support in sdhci-msm
driver.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During tuning execution for HS400 mode, HW sequence recommends
to select MCLK_SEL/2(0x3) in VENDOR_SPEC & sdhc msm clock at GCC
to be 400MHZ (nearest supported clk). Add this change in tuning
sequence during HS400 tuning.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clear SDHCI_HS400_TUNING flag after platform_execute_tuning
so that platform_execute_tuning may use it if needed.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program CORE_CSR_CDC_DELAY_CFG for hardware recommended 1.25ns delay.
We may see data CRC errors if it's programmed for any other delay
value.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The vendor specific func register doesn't get reset when using the
software reset register. The various bootloader's could leave this
in an unknown state, hence reset this register to it's power on reset
value during probe.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out sdhci_msm_hs400 used for DLL calibration in HS400
modes. This function will be needed for enhanced_strobe as well.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out msm_set/get_clock_rate_for_bus_mode for it's later
use in changing the tuning sequence for selecting HS400
bus speed mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This factors out sdhci_msm_hc_select_mode to later use
it during enhanced_strobe mode select.
It also further breaks sdhci_msm_hc_select_mode
into separate functions for configuring HS400 mode
or other modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23) on the MXS MMC host driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->dma_addr can store a value that is not returned by the DMA API,
so it is safer to check if is a valid DMA address indirectly.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With commit 67bf5156ed ("gpio / ACPI: fix returned error from
acpi_dev_gpio_irq_get()"), mmc_gpiod_request_cd() returns -EPROBE_DEFER if
GPIO is not ready when sdhci-acpi driver is probed, and sdhci-acpi driver
should be probed again later in this case.
This fixes an order issue when both GPIO and sdhci-acpi drivers are built
as modules.
CC: stable@vger.kernel.org # v4.9
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177101
Tested-by: Jonas Aaberg <cja@gmx.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A significant amount of functions are available through the public mmc
host.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc host.h header file.
This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
A significant amount of functions and other definitions are available
through the public mmc card.h header file. Let's slim down this public mmc
interface, as to prevent users from abusing it, by moving some of the
functions/definitions to private mmc header files.
This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.
Cc: linux-omap@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
A significant amount of functions are available through the public mmc
core.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc header files.
This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups, as an example
some functions can be turned into static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
This is the first step in cleaning up the private mmc header files. In this
change we makes sure each header file builds standalone, as that helps to
resolve dependencies.
While changing this, it also seems reasonable to stop including other
headers from inside a header itself which it don't depend upon.
Additionally, in some cases such dependencies are better resolved by
forward declaring the needed struct.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
I got this new build error on today's linux-next
drivers/mmc/host/s3cmci.h:69:24: error: field 'pio_tasklet' has incomplete type
struct tasklet_struct pio_tasklet;
drivers/mmc/host/s3cmci.c: In function 's3cmci_enable_irq':
drivers/mmc/host/s3cmci.c:390:4: error: implicit declaration of function 'enable_irq';did you mean 'enable_imask'? [-Werror=implicit-function-declaration]
While I haven't found out why this happened now and not earlier, the
solution is obvious, we should include the header that defines
the structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To validate whether native hotplug needs to be used, the tmio driver checks
whether the mmc->slot.cd_irq has been successfully assigned.
This check is redundant at its current place in tmio_mmc_host_probe(), as
the mmc core assigns mmc->slot.cd_irq a valid value first when
mmc_gpiod_request_cd_irq() is called. Therefore, let's just remove the
check for now, as that also removes a layering violation of the tmio driver
accessing core specific data via ->slot.cd_irq.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The eSDHC_PRSSTAT[SDSTB] bit indicates whether the internal card clock is
stable. This bit is for the host driver to poll clock status when changing
the clock frequency. It is recommended to clear eSDHC_SYSCTL[SDCLKEN]
to remove glitch on the card clock when the frequency is changing. This
patch is to disable SDCLKEN bit before changing frequency and enable it
after SDSTB bit is set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's unnecessary to check the irqs_queued value as
it always needs to queue one if irq isn't enabled.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per SDIO Simplified Specification V3, section 3.1.2, A host that
supports UHS-I sets S18R to 1 in the argument of CMD5 to request a
change of the signal voltage to 1.8V. If the card supports UHS-I and
the current signal voltage is 3.3V, S18A is set to 1 in the R4 response.
If the signal voltage is already 1.8V, the card sets S18A to 0 so that
host maintains the current signal voltage. UHS-I is supported in SD mode
and S18A is always 0 in SPI mode.
For the current code, if the signaling voltage is fixed 1.8v, so
the card will set S18A to 0 for rocr and thus we would clear the
R4_18V_PRESENT from ocr, which make core won't try to use uhs mode.
To fix it, we expect sdio_read_cccr would fail if the uhs mode won't
work at all. Note that it's interesting that some sdio cards still
response S18A even the voltage is fixed to 1.8v and the CMD11 will
also accepted and finish enabling UHS mode successfully. I guess this
is why folks didn't notice this problem. Anyway, fix it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add new helper function, mmc_sdio_resend_if_cond, to be
reused when trying to retry the init sequence.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* The script "checkpatch.pl" pointed information out like the following.
WARNING: Prefer kcalloc over kzalloc with multiply
Thus fix the affected source code place.
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: quoted string split across lines
Thus fix affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use space characters at some source code places according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: Prefer seq_puts to seq_printf
Thus fix the affected source code place.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a missing character in the function description.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The probe exit path on error does nothing since commit 94b110aff8
("mmc: tmio: add tmio_mmc_host_alloc/free()"), so we can bail out
immediately.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The caller may supply connection ID, index, or both. All combinations are
possible and mmc framework should not make any assumption on what exactly
caller wants.
Remove con_id override conditionals in mmc_gpiod_request_ro() and
mmc_gpiod_request_cd().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd_con_id is not used and always NULL.
Remove it to make code a bit more cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
msdc_card_busy only need check if the data0 is low.
In sdio data1 irq mode, data1 may be low because of interruption.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initially all QorIQ platforms were PowerPC architecture and they didn't
support card detection except several platforms. The driver added the
quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION as default and this made broken-cd
property in dts node didn't work. Now QorIQ platform turns to ARM
architecture and most of them could support card detection. However it's
a large number of dts trees that need to be fixed with broken-cd if we
remove the default SDHCI_QUIRK_BROKEN_CARD_DETECTION in driver. And the
users don't want to see this. So this patch is to remove this default
quirk just for ARM and keep it for PowerPC.(Note, QorIQ PowerPC platform
only has big-endian eSDHC while QorIQ ARM platform has big-endian or
little-endian eSDHC) This makes broken-cd property work again for ARM.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC register definitions in header file were messy and confusing.
This patch is to clean up these definitions.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver adds initial support for the DW host controller
found on ZTE SoCs.
It has been tested on ZX296718 EVB board currently. More support on
timing tuning will be added when hardware is available.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Data done irq is expected if data length is less than
watermark in PIO mode. But fifo watermark is requested
to be aligned with data length in some SoC so that TX/RX
irq can be generated with data done irq. Add the
watermark alignment to mark this requirement and force
fifo watermark setting accordingly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The FIFO address may break default address assumption of 0x100
(version < 0x240A) and 0x200(version >= 0x240A) in current driver.
The new property is introduced to override fifo address via DT
node information.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An mmc host driver shouldn't rely on interrupt.h being included by another
public mmc header. Instead make that dependency explicit by including
interrupt.h in those host drivers that depends on it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Don't rely on host.h to include the leds.h header, but instead include it
explicitly because the driver depends on it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Don't rely on host.h to include the mmc.h header, but instead include it
explicitly because the driver depends on it.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
There are currently no external users of the public dw_mmc header file,
except the dw_mmc driver itself. Therefore let's move the definitions from
the public dw_mmc header file into the existing private dw_mmc header file
and then remove the public one.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There are currently no users of the clk_ctrl2_present member from the
platform data, so let's remove it.
Note, as some of the sh_mmcif variants may support clk_ctrl2, let's keep
the current code in the driver, which deals with this. For future support,
we should invent a DT binding instead, but let's leave that until it's
needed.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There are currently no users of the ccs_unsupported member from the
platform data, so let's remove it.
Note, as some of the sh_mmcif variants may not support ccs, let's keep the
current code in the driver, which deals with this. For future support, we
should invent a DT binding instead, but let's leave that until it's needed.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Removing the callback also enables us to remove the sh_mmcif_get_cd()
altogether, as we convert to use mmc_gpio_get_cd() to the same kind of
work.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the BCM2835 datasheet the maximum block size for the
eMMC module is restricted to the internal data FIFO which is 1024 byte.
But this is still an improvement to the default of 512 byte.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the mmc module on bcm2835 neither provide a capabilities register nor
free documentation we must rely on the downstream implementation [1].
So enable the following capabilities for bcm2835:
MMC_CAP_MMC_HIGHSPEED
MMC_CAP_SD_HIGHSPEED
MMC_CAP_DRIVER_TYPE_A
MMC_CAP_DRIVER_TYPE_C
[1] - https://github.com/raspberrypi/linux/blob/rpi-4.4.y/drivers/mmc/host/bcm2835-mmc.c
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the MMC subsystem, we see such initializers that only clears the
first member explicitly.
For example,
struct mmc_request mrq = {NULL};
sets the first member (.sbc) to NULL explicitly. However, this is
an unstable form because we may insert a non-pointer member at the
top of the struct mmc_request in the future. (if we do so, the
compiler will spit warnings.)
So, using a designated initializer is preferred coding style. The
expression above is equivalent to:
struct mmc_request mrq = { .sbc = NULL };
Of course, this does not express our intention. We want to fill
all struct members with zeros. Please note struct members are
implicitly zero-cleared unless otherwise specified in the initializer.
After all, the most reasonable (and stable) form is:
struct mmc_request mrq = {};
Do likewise for mmc_command, mmc_data as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With gcc-4.1.2:
mmc/core/block.c: In function ‘mmc_blk_issue_discard_rq’:
mmc/core/block.c:1150: warning: ‘arg’ may be used uninitialized in this function
mmc/core/block.c:1150: warning: ‘nr’ may be used uninitialized in this function
mmc/core/block.c:1150: warning: ‘from’ may be used uninitialized in this function
While this is a false positive, it can be avoided easily by jumping over
the checks for "err" that are always false.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the eMMC 5.0 version of the spec, several EXT_CSD fields about
device lifetime are added.
- Two types of estimated indications reflected by averaged wear out of memory
- An indication reflected by average reserved blocks
Export the information through sysfs.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setup tuning when the board is HS200 enabled.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function will only be available if SDR104 was detected in probe,
so no need to check in the function itself again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function will only be available if SDR104 was detected in probe,
so no need to check in the function itself again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The capability for HW_RESET is only activated if SDR104 is present, so
no need to check for SDR104 in the function itself again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Prerequisites for tuning are the same as for hw_reset. We need an SCC
and a supported mode. Populate the tuning related functions only when
those conditions are met. This also removes a tiny race window.
Previously, the functions were populated when the SCC offset was not
initialized which could have led to an OOPS.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need a SCC unit for hw_reset. Those units can only be described in
of_data. So, of_data and a valid SCC offset are prerequisites for
enabling the hw_reset capability. Merge the two 'if' conditions into one
and add a check for an scc offset.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By using the helper of_device_get_match_data(), we can skip some
checking and make the code simpler.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The master bit to enable SDIO interrupts can only be accessed if
SCLKDIVEN bit allows that. However, the core uses the SDIO enable
callback at times when SCLKDIVEN forbids the change. This leads to
"timeout waiting for SD bus idle" messages.
We now activate the master bit in probe once if SDIO is supported. IRQ
en-/disabling will be done now by the individual IRQ enablement bits
only.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This fixes a race condition that may occur whenever ST micro busy end
interrupt is raised just after being unmasked but before leaving mmci
interrupt context.
A dead-lock has been found if connecting mmci ST Micro variant whose amba
id is 0x10480180 to some new eMMC that supports internal caches. Whenever
mmci driver enables cache control by programming eMMC's EXT_CSD register,
block driver may request to flush the eMMC internal caches causing mmci
driver to send a MMC_SWITCH command to the card with FLUSH_CACHE operation.
And because busy end interrupt may be mistakenly cleared while not yet
processed, this mmc request may never complete. As a result, mmcqd task
may be stuck forever.
Here is an instance caught by lockup detector which shows that mmcqd task
was hung while waiting for mmc_flush_cache command to complete:
..
[ 240.251595] INFO: task mmcqd/1:52 blocked for more than 120 seconds.
[ 240.257973] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.263109] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.270955] mmcqd/1 D c047504c 0 52 2 0x00000000
[ 240.277359] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.284418] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.292191] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.300491] [<c0476040>] (wait_for_common) from [<c02efc1c>] (mmc_wait_for_req_done+0x4c/0x13c)
[ 240.309224] [<c02efc1c>] (mmc_wait_for_req_done) from [<c02efd90>] (mmc_wait_for_cmd+0x64/0x84)
[ 240.317953] [<c02efd90>] (mmc_wait_for_cmd) from [<c02f5b14>] (__mmc_switch+0xa4/0x2a8)
[ 240.325964] [<c02f5b14>] (__mmc_switch) from [<c02f5d40>] (mmc_switch+0x28/0x30)
[ 240.333389] [<c02f5d40>] (mmc_switch) from [<c02f0984>] (mmc_flush_cache+0x54/0x80)
[ 240.341073] [<c02f0984>] (mmc_flush_cache) from [<c02ff0c4>] (mmc_blk_issue_rq+0x114/0x4e8)
[ 240.349459] [<c02ff0c4>] (mmc_blk_issue_rq) from [<c03008d4>] (mmc_queue_thread+0xc0/0x180)
[ 240.357844] [<c03008d4>] (mmc_queue_thread) from [<c003cf90>] (kthread+0xdc/0xf4)
[ 240.365339] [<c003cf90>] (kthread) from [<c0010068>] (ret_from_fork+0x14/0x2c)
..
..
[ 240.664311] INFO: task partprobe:564 blocked for more than 120 seconds.
[ 240.670943] Not tainted 4.1.13-00510-g9d91424 #2
[ 240.676078] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.683922] partprobe D c047504c 0 564 486 0x00000000
[ 240.690318] [<c047504c>] (__schedule) from [<c04754a0>] (schedule+0x40/0x98)
[ 240.697396] [<c04754a0>] (schedule) from [<c0477d40>] (schedule_timeout+0x148/0x188)
[ 240.705149] [<c0477d40>] (schedule_timeout) from [<c0476040>] (wait_for_common+0xa4/0x170)
[ 240.713446] [<c0476040>] (wait_for_common) from [<c01f3300>] (submit_bio_wait+0x58/0x64)
[ 240.721571] [<c01f3300>] (submit_bio_wait) from [<c01fbbd8>] (blkdev_issue_flush+0x60/0x88)
[ 240.729957] [<c01fbbd8>] (blkdev_issue_flush) from [<c010ff84>] (blkdev_fsync+0x34/0x44)
[ 240.738083] [<c010ff84>] (blkdev_fsync) from [<c0109594>] (do_fsync+0x3c/0x64)
[ 240.745319] [<c0109594>] (do_fsync) from [<c000ffc0>] (ret_fast_syscall+0x0/0x3c)
..
Here is the detailed sequence showing when this issue may happen:
1) At probe time, mmci device is initialized and card busy detection based
on DAT[0] monitoring is enabled.
2) Later during run time, since card reported to support internal caches, a
MMCI_SWITCH command is sent to eMMC device with FLUSH_CACHE operation. On
receiving this command, eMMC may enter busy state (for a relatively short
time in the case of the dead-lock).
3) Then mmci interrupt is raised and mmci_irq() is called:
MMCISTATUS register is read and is equal to 0x01000440. So the following
status bits are set:
- MCI_CMDRESPEND (= 6)
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is 0x3FF, status variable is set to 0x00000040 and
BIT MCI_CMDRESPEND is cleared by writing MMCICLEAR register.
Then mmci_cmd_irq() is called. Considering the following conditions:
- host->busy_status is 0,
- this is a "busy response",
- reading again MMCISTATUS register gives 0x1000400,
MMCIMASK0 is updated to unmask MCI_ST_BUSYEND bit.
Thus, MMCIMASK0 is set to 0x010003FF and host->busy_status is set to wait
for busy end completion.
Back again in status loop of mmci_irq(), we quickly go through
mmci_data_irq() as there are no data in that case. And we finally go
through following test at the end of while(status) loop:
/*
* Don't poll for busy completion in irq context.
*/
if (host->variant->busy_detect && host->busy_status)
status &= ~host->variant->busy_detect_flag;
Because status variable is not yet null (is equal to 0x40), we do not leave
interrupt context yet but we loop again into while(status) loop. So we run
across following steps:
a) MMCISTATUS register is read again and this time is equal to 0x01000400.
So that following bits are set:
- MCI_DATABLOCKEND (= 10)
- MCI_ST_CARDBUSY (= 24)
Since MMCIMASK0 register is equal to 0x010003FF:
b) status variable is set to 0x01000000.
c) MCI_ST_CARDBUSY bit is cleared by writing MMCICLEAR register.
Then, mmci_cmd_irq() is called one more time. Since host->busy_status is
set and that MCI_ST_CARDBUSY is set in status variable, we just return from
this function.
Back again in mmci_irq(), status variable is set to 0 and we finally leave
the while(status) loop. As a result we leave interrupt context, waiting for
busy end interrupt event.
Now, consider that busy end completion is raised IN BETWEEN steps 3.a) and
3.c). In such a case, we may mistakenly clear busy end interrupt at step
3.c) while it has not yet been processed. This will result in mmc command
to wait forever for a busy end completion that will never happen.
To fix the problem, this patch implements the following changes:
Considering that the mmci seems to be triggering the IRQ on both edges
while monitoring DAT0 for busy completion and that same status bit is used
to monitor start and end of busy detection, special care must be taken to
make sure that both start and end interrupts are always cleared one after
the other.
1) Clearing of card busy bit is moved in mmc_cmd_irq() function where
unmasking of busy end bit is effectively handled.
2) Just before unmasking busy end event, busy start event is cleared by
writing card busy bit in MMCICLEAR register.
3) Finally, once we are no more busy with a command, busy end event is
cleared writing again card busy bit in MMCICLEAR register.
This patch has been tested with the ST Accordo5 machine, not yet supported
upstream but relies on the mmci driver.
Signed-off-by: Sarang Mairal <sarang.mairal@garmin.com>
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The block layer won't send requests the driver isn't asking for,
so remove this check.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
One of our kernelCI boxes hanged at boot because a faulty eSDHC device
was triggering spurious CARD_INT interrupts for SD cards, causing CMD52
reads, which are not allowed for SD devices. This adds a sanity check
to the interruption path, preventing that illegal command from getting
sent if the CARD_INT interruption should be disabled.
This quirk allows that particular machine to resume boot despite the
faulty hardware, instead of getting hung dealing with thousands of
mishandled interrupts.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: <stable@vger.kernel.org>
It's necessary to setup bus if any slots are present.
- update clock after ctrl reset
- if the host has genpd node, we can guarantee the clock is
available before starting request. Otherwies, the clock register
is reset once power off the pd, and host can't output the active
clock during communication.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Fixes: df9bcc2bc0 ("mmc: dw_mmc: add missing codes for runtime resume")
cc: <stable@vger.kernel.org>
Reported-by: Randy Li <randy.li@rock-chips.com>
Reported-by: S. Gilles <sgilles@math.umd.edu>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Regressions for not being able to detect an eMMC HS DDR mode card has been
reported for the sdhci-esdhc-imx driver, but potentially other sdhci
variants may suffer from the similar problem.
The commit e173f8911f ("mmc: core: Update CMD13 polling policy when
switch to HS DDR mode"), is causing the problem. It seems that change moved
one step to far, regarding changing the host's timing before polling for a
busy card.
To fix this, let's move back to the behaviour when the host's timing is
updated after the polling, but before the switch status is fetched and
validated.
In cases when polling with CMD13, we keep validating the switch status at
each attempt. However, to align with the other card busy detections
mechanism, let's fetch and validate the switch status also after the host's
timing is updated.
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Gary Bisson <gary.bisson@boundarydevices.com>
Fixes: e173f8911f ("mmc: core: Update CMD13 polling policy when switch..")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
According to the code the intention is to append 8 SCK cycles
instead of 4 at end of a MMC_STOP_TRANSMISSION command. But this
will never happened because it's an AC command not an ADTC command.
So fix this by moving the statement into the right function.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: e4243f13d1 (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are
powered when probing") introduced code to powerup any acpi child
nodes listed in the dstd. But some dstd-s list all possible devices
used on some board variants, while reporting if the device is actually
present and enabled in the status field of the device.
So we end up calling the acpi _PS0 (power-on) method for devices which
are not actually present. This does not always end well, e.g. on my
cube iwork8 air tablet, this results in freezing the entire tablet as
soon as the r8723bs module is loaded.
This commit fixes this by checking the child device's status.present
and status.enabled bits and only call acpi_device_fix_up_power()
if both are set.
Fixes: e5bbf30733 ("mmc: sdhci-acpi: Ensure connected devices are powered when probing")
BugLink: https://github.com/hadess/rtl8723bs/issues/80
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No actual segmentation faults were observed but the coding is
at least inconsistent.
irqreturn_t meson_mmc_irq():
We should not dereference host before checking it.
meson_mmc_irq_thread():
If cmd or mrq are NULL we should not dereference them after
writing a warning.
Fixes: 51c5d8447b MMC: meson: initial support for GX platforms
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mmc_read_ssr() function results in DMA to the raw_ssr member of
struct mmc_card, which is not guaranteed to be cache line aligned & thus
might not meet the requirements set out in Documentation/DMA-API.txt:
Warnings: Memory coherency operates at a granularity called the cache
line width. In order for memory mapped by this API to operate
correctly, the mapped region must begin exactly on a cache line
boundary and end exactly on one (to prevent two separately mapped
regions from sharing a single cache line). Since the cache line size
may not be known at compile time, the API will not enforce this
requirement. Therefore, it is recommended that driver writers who
don't take special care to determine the cache line size at run time
only map virtual regions that begin and end on page boundaries (which
are guaranteed also to be cache line boundaries).
On some systems where DMA is non-coherent this can lead to us losing
data that shares cache lines with the raw_ssr array.
Fix this by kmalloc'ing a temporary buffer to perform DMA into. kmalloc
will ensure the buffer is suitably aligned, allowing the DMA to be
performed without any loss of data.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 5275a652d2 ("mmc: sd: Export SD Status via “ssr” device attribute")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e0097cf5f2 ("mmc: queue: Fix queue thread wake-up") did not go far
enough. mmc_wait_for_data_req_done() still contains some problems and can
be further simplified. First it should not touch
context_info->is_waiting_last_req because that is a wake-up control used by
the owner of the context. Secondly, it should always return when one of its
wake-up conditions is met because, again, that is contolled by the owner of
the context.
While the current block driver does not have an issue, these problems were
exposed during testing of the Software Command Queue patches.
Fixes: e0097cf5f2 ("mmc: queue: Fix queue thread wake-up")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Harjani Ritesh <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit c2c24819b2 ("mmc: core: Don't power off the card when
starting the host"), the power state can still be MMC_POWER_UNDEFINED after
mmc_start_host() is called. That can trigger a warning in SDHCI during
runtime resume as it tries to restore the I/O state. Handle
MMC_POWER_UNDEFINED simply by not updating the I/O state in that case.
Fixes: c2c24819b2 ("mmc: core: Don't power off the card when starting the host")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a Socionext SoC specific compatible (suggested by Rob Herring).
No SoC specific data are associated with the compatible strings for
now, but other SoC vendors may use this IP and want to differentiate
IP variants in the future.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Move files from the card directory to the core directory to enable
future clean-ups of the generic mmc header files and interfaces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U2+h
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull another MMC update from Ulf Hansson:
"Here's a second pull request for MMC for v4.10.
As a matter of fact it's only one change that moves some mmc files
around. I thought it was a good idea to get this into v4.10, as it
gives us a nice and fresh base for v4.11. Summary:
MMC core:
- Move files from the card directory to the core directory to enable
future clean-ups of the generic mmc header files and interfaces"
* tag 'mmc-v4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: block: Move files to core
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
Once upon a time it made sense to keep the mmc block device driver and its
related code, in its own directory called card. Over time, more an more
functions/structures have become shared through generic mmc header files,
between the core and the card directory. In other words, the relationship
between them has become closer.
By sharing functions/structures via generic header files, it becomes easy
for outside users to abuse them. In a way to avoid that from happen, let's
move the files from card directory into the core directory, as it enables
us to move definitions of functions/structures into mmc core specific
header files.
Note, this is only the first step in providing a cleaner mmc interface for
outside users. Following changes will do the actual cleanup, as that is not
part of this change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.
For SD, it basically relies on the SDHCI standard code.
For eMMC, this driver provides some callbacks to support the
hardware part that is specific to this IP design.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SDHCI-compat controllers support not only SD, but also eMMC,
but they use different commands for tuning: CMD19 for SD, CMD21 for
eMMC.
Due to the difference of the underlying mechanism, some controllers
(at least, the Cadence IP is the case) provide their own registers
for the eMMC tuning.
This commit will be useful when we want to override .execute_tuning
callback (for eMMC HS200 tuning), but still let it fall back to
sdhci_execute_tuning() for SD timing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
