The original description was for LAG, so fix it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove a bridged port from the flooding domain of unknown unicast
packets according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling a range of VLANs on a bridged port we can configure
flooding for these VLANs by one register access instead of calling the
same register for each VLAN. This is accomplished by using the 'range'
field of the Switch Flooding Table Register (SFTR).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a flag anyway, so move it to existing u8 flag and don't waste mem.
Fix the flags to be in single u8 on the way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for new generation Mellanox Spectrum ASIC, 10/25/40/50 and
100Gb/s Ethernet Switch.
The initial driver implements bridge forwarding offload including
bridge internal VLAN support, FDB static entries, FDB learning and
HW ageing including their setup.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we currently do not support the offloading of 802.1D bridges, we
need to be able to let the device know it should not learn MAC addresses
on specific {Port, VID} pairs.
Add the SPVMLR register, which controls the learning enablement of
{Port, VID} pairs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SFDAT which is used to control switch ageing time.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for a port to support {Port, VID} to FID mapping it needs to be
configured to a virtual port mode (as opposed to VLAN mode).
Add the SVPE register, which enables port virtualization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An incoming packet can be classified into a filtering identifer (FID)
based on its VID or incoming port and VID ({Port, VID}).
Add the SVFA register, which controls this mapping.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filtering identifiers (FIDs) are unique identifers of bridge instances
in the hardware.
Add the SFMR register, which is responsible for the creation and
configuration of these FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions of SBPR, SBCM, SBPM, SBMM and PBMC registers that are
used to configure shared buffers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPVID and SPVM registers responsible for default port VID
configuration and VLAN membership of a port.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SFN register which is used to poll for newly added and aged-out FDB
entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SFD register which is responsible for filtering database
manipulation, including static and dynamic FDB entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing item helper which allows to access char bufs on multiple
offsets. This is needed by SFD and SFN register definitions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets destined to offloaded netdevs will be classified to FIDs in the
device and flooded in case of BUM.
The flooding table used is of type FID-offset, which allows one to
create different flooding domains for different FIDs and specify the
offset in the flooding table for each FID (not necessarily equal to FID
or VID).
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the newly introduced Spectrum switch ASIC, packets destined to not
offloaded netdevs will be classified to special FIDs (vFIDs) in the
device and flooded to the CPU port.
The flooding table used is of type per-FID, which allows one to create
different flooding domains for different vFIDs.
While using a simple single-entry flood table is certainly sufficient at
this point, we do plan to offload 802.1D bridges involving VLAN
interfaces, thus making this change necessary.
Add support for this flooding table type, by exposing the configuration
of the number of tables from this type and their size.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the introduction of L2 offloads, allow different ports to
join/leave the flooding domain, according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The meaning of certain parameters in the profile passed to the device
during initialization has changed, so update their documentation
accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we trapped flooded and control packets using the same trap
group. This can cause flooded packets to overflow the PCI bus and
prevent control packets (e.g. STP, LACP) from getting to the CPU.
Solve this by splitting the RX trap group to RX and control, which allows
us to configure a policer on the first, thereby preventing it from
overflowing the PCI bus.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Host Trap Group Table (HTGT) register configures trap groups, which
are populated with trap IDs using the Host PacKet Trap (HPKT) register.
However, a trap ID can only be present inside one trap group (the last
configured).
Instead of passing both the trap group and ID for the function that
packs HPKT, pass only the trap ID and derive from it the trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce separate helper for packing SPMS VIDs, as it can be used for
multiple VIDs and not only for one as previous SPMS pack function
provided.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define max which would be needed later on.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be symmetric with mlxsw_emad_init and don't use EMADs in mlxsw_emad_fini
cleanup function. Use command interface instead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware accepts only limited number of mapping entries for MAP_FA
command. In order to prevent overflow, introduce a limit and in case the
number of entries is bigger, call MAP_FA multiple times.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove strict number check of queues count as various ASICs have
different counts.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The count of CQs can be different for various ASICs, so just define
maximal value and check for that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With respect to a firmware change, the Switch Multicast ID (SMID)
register is no longer needed, so the related configuration code can be
removed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain conditions EMAD responses can be returned from the device
even before setting trans_active. This will cause the EMAD Rx listener
to drop the EMAD response - as there are no active transactions - and
timeouts will be generated.
Fix this by setting trans_active before transmitting the EMAD skb.
Fixes: 4ec14b7634 ("mlxsw: Add interface to access registers and process events")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating the shift needed in order to access a bit array element
in a byte, we should multiply the index by the element size and not
assume it is fixed at 2-bits.
Fixes: 93c1edb27f ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recently added mlxsw driver produces warnings in ARM
allmodconfig:
drivers/net/ethernet/mellanox/mlxsw/pci.c: In function 'mlxsw_pci_cmd_exec':
drivers/net/ethernet/mellanox/mlxsw/pci.c:1585:59: warning: right shift count >= width of type [-Wshift-count-overflow]
linux/byteorder/big_endian.h:38:51: note: in definition of macro '__cpu_to_be32'
drivers/net/ethernet/mellanox/mlxsw/pci.c:76:2: note: in expansion of macro 'iowrite32be'
This uses upper_32_bits() to extract the bits while avoiding that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Fixes: eda6500a98 "mlxsw: Add PCI bus implementation"
Signed-off-by: David S. Miller <davem@davemloft.net>
To be aligned with obj.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HW-SW contract requires mailboxes passed to the firmware to be 4KB
aligned. Previously, these mailboxes were mapped using streaming DMA
routines, which do not guarantee the bus addresses to be 4KB aligned.
Under certain conditions this constraint was indeed violated and errors
were observed.
By using consistent DMA mapping routines together with a mailbox size of
4KB we are guaranteed not to violate the constraint.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmit fails, it is an error, not a warning.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use '%zx' to print size_t format in order to fix the following build warning:
drivers/net/ethernet/mellanox/mlxsw/item.h:65:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type 'size_t' [-Wformat=]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the length of the skb before transmitting it and use it for stats
instead of skb->len, since skb might have been freed already.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use the length of the transmitted skb (which was freed), but
that of the response skb.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only checked if the transmission queue is not full in the
middle of the xmit function. This lead to complex logic due to the fact
that sometimes we need to reallocate the headroom for our Tx header.
Allow the switch driver to know if the transmission queue is not full
before sending the packet and remove this complex logic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FCS of incoming packets is already checked by HW. Just strip it out.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves compile errors on um-allyesconfig.
Note that there are many other drivers which have the same issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
