The vbt on my Fujitsu-Siemens Lifebook S6010 provides two 800x600 modes,
60Hz and 56Hz. The magic register values we have correspond to the 60Hz
mode, and as I don't know how one would trick the VGA BIOS to set up
the 56Hz mode we can't get the magic values for the orther mode. So
when checking whether a mode is valid also check the pixel clock so that
we filter out the 56Hz variant.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Richter <richter@rus.uni-stuttgart.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In my earlier rewrite I missed a few important registers. Thomas Richter
noticed that they're needed to make his machine resume correctly.
Looks like IEGD does a one time init of these three registers. We don't
have a good one time init place in the ns2501 driver, so let's just
stick them into the .mode_set() hook and see if that helps things along.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Richter <richter@rus.uni-stuttgart.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Try to use the same programming sequence as used by the IEGD driver.
Also shovel the magic register values into a big static const array.
The register values are actually the based on what the BIOS programs
on the Fujitsu-Siemens Lifebook S6010. IEGD seemed to have hardcoded
register values (which also enabled the scaler for 1024x768 mode).
However those didn't actually work so well on the S6010. Possibly the
pipe timings that got used didn't match the ns2501 configuration.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Richter <richter@rus.uni-stuttgart.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thomas Richter <richter@rus.uni-stuttgart.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next after the big s/crtc->fb/crtc->primary->fb/
cocinelle patch to avoid endless amounts of conflict hilarity in my
-next queue for 3.16.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DRM_DEBUG_KMS includes printing the function name.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are only a few users of the DRM_LOG_KMS() macro. We can simplify
the DRM code a bit by replacing them by DRM_DEBUG_KMS().
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the change in the modeset sequence this shouldn't be required
any more since the ->mode_set callback now gets called when the dvo
port is fully up and running.
Also limit the retry loop to 10 tries to avoid hanging the machine
while holding important modeset locks.
Cc: Thomas Richter <thor@math.tu-berlin.de>
Tested-by: Thomas Richter <thor@math.tu-berlin.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to the sdvo code we poke the dvo encoder whether the output is
active. Safe that dvo encoders are not standardized, so this requires
a new callback into the dvo chip driver.
Hence implement that for all 6 dvo drivers.
v2: With the newly added ns2501 we now have 6 dvo drivers instead of
just 5 ...
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All dvo drivers only support 2 dpms states, and our dvo driver
even switches of the dvo port for anything else than DPMS_ON. Hence
ditch this complexity and simply use bool enable.
While reading through this code I've noticed that the mode_set
function of ch7017 is a bit peculiar - it disable the lvds again, even
though the crtc helper code should have done that ... This might be to
work around an issue at driver load, we pretty much ignore the hw
state when taking over.
v2: Also do the conversion for the new ns2501 driver.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the pipe A quirk properly fixed up for i830M, this shouldn't be
required any longer.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for the ns2501 DVO, found in some older Fujitsu/Siemens Labtops.
It is in the state of "works for me".
Includes now proper DPMS support. Includes switching between resolutions -
from 640x480 to 1024x768.
Currently assumes that the native display resolution is 1024x768.
The ns2501 seems to be rather critical - if the output PLL is not
running, the chip doesn't seem to be clocked and then doesn't react
on i2c messages. Thus, a quick'n-dirty trick ensures that the DVO
is active before submitting any i2c messages to it. This is
probably to be reviewed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17902
Signed-off-by: Thomas Richter <thor@math.tu-berlin.de>
[danvet: fixup whitespace fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
