Issue:
Pending IO wait does not complete after triggering Graceful reset,
causing ack timeout and call traces.
Fix:
1. Reducing the IO command wait timeout before triggering reset,
as logically also timeout should be less than reset timeout (10sec).
2. Moving the abort IO after chip reset, because only after
chip reset, driver owns the IO otherwise it is with firmware and can
still revert back with response.
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
While booting with kdump kernel, driver receive IOCB interrupts
for which it is not ready which results in processing them
before init_firmware during driver probe
Fix:
Two steps solution
1. Make driver ready to process the interrupt before interupts
handlers is registered.
2. Stop driver processing iocb interrupts if not generated as per
firmware protocol i.e R2H bit set
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Mailbox command 0x102 (IDC Time Extend) failure seen while applying
changes to iface using iscsiadm
Fix:
Added fix to extend IDC timeout only for ISP84xx when IDC ACK
needs to be posted and disable ACB mailbox command completion
is in intermediate state.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
qla4xxx Unable to clear DDB indices when logout fails due to
failure of connection close mbox command.
Root cause:
If login to session fail, iscsiadm make call to destroy_session.
qla4xxx driver does not free ddb index map before free_ddb()
Fix:
Clear DDB Index map before free_ddb in "destroy_session"
in case of connection close mailbox command failure with 4005h.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If waiting for signals was interrupted then the device was put to
FAILED state. Use msleep instead of msleep_interruptible to handle
this correctly.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed AF_83XX_NO_FWDUMP flag and directly checking IDC_CTRL bit1
while taking minidump, to check for graceful reset.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
For ISP8xxx, adapter initialization is not retried if
qla4xxx_initialize_adapter fails.
Fix:
If qla4xxx_initialize_adapter fails, first check if failure is due to IRQs not
attached in order to skip retrial, then free the IRQs and then retry
initializing the adapter.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
This patch fixed several typo in printk from various
part of kernel source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Recreate the chap data list during the get chap operation in
qla4xxx_get_chap_list().
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added support for Diagnostics MBOX command via BSG Vendor HST_VENDOR
interface. This command provides various tests for validating hardware
functionality.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We should cap the size of memcpy() because it comes from the network
and can't be trusted.
Fixes: 26ffd7b45f ('[SCSI] qla4xxx: Add support to set CHAP entries')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Add support to get local CHAP - index, username and password,
sysfs params of iscsi session corresponding to flash target entry.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Provide support to add/update the CHAP entries in adapter's flash
using iscsi tools, like Open-iSCSI.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To write a CHAP entry in adapter's flash calculate the offset based
on the type of adapter.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If any flash target entry is using CHAP authentication then set
CHAP username and password sysfs params for the corresponding
iscsi sessions.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Support setting of CHAP_OUT_IDX param for the target entry in flash.
Setting of valid local CHAP index with enable CHAP AUTH for that
flash target entry and disabling CHAP AUTH will invalidate the CHAP
index for the flash target entry.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Earlier logic for driver created iscsi_session->discovery_parent_idx
was to store ram index of a sendtarget entry, but driver frees
sendtarget ram index as soon as firmware is done with discovery,
which is available for further use. So changing the logic to point
iscsi_session->discovery_parent_idx to store sendtarget flashnode index.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound),
the driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Return error from function qla4_8xxx_collect_md_data()
if minidump data collection fails.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add pex-dma support for ISP8324 and ISP8042 to improve
the minidump capture time.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While loopback diagnostic is in progress, disable the ACB which resets
all the active connections to target. Disable ACB would filter out all
the DHCP multicast and broadcast packets which otherwise cause the
diagnostic test to take longer time to complete or failures in some
other cases.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Flash target index 0 and 1 are reserved for boot target entries created
with BIOS utility.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While setting the values for DDB, discovery_parent_idx needs to be used
instead of discovery_parent_type.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If logout is performed on a failed session entry then that session
should be gracefully removed.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For the workqueue creation interfaces that do not expect format strings,
make sure they cannot accidently be parsed that way. Additionally, clean
up calls made with a single parameter that would be handled as a format
string. Many callers are passing potentially dynamic string content, so
use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a bug where the iscsi class/driver did not do a put_device
when a sess/conn device was found. This also simplifies the interface
by not having to pass in some arguments that were duplicated and did
not need to be exported.
Reported-by: Zhao Hongjiang <zhaohongjiang@huawei.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Assign values using correct datatype in function qla4xxx_copy_to_fwddb_param()
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix following warning:
drivers/scsi/qla4xxx/ql4_os.c:5507:5:
warning: symbol 'qla4xxx_sysfs_ddb_tgt_create' was not declared. Should it be
static?
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix followig gcc warning:-
drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_sysfs_ddb_get_param’:
drivers/scsi/qla4xxx/ql4_os.c:6279:
warning: comparison is always true due to limited range of data type
drivers/scsi/qla4xxx/ql4_os.c:6290:
warning: comparison is always true due to limited range of data type
drivers/scsi/qla4xxx/ql4_os.c: In function ‘qla4xxx_sysfs_ddb_delete’:
drivers/scsi/qla4xxx/ql4_os.c:6593:
warning: ‘ddb_size’ may be used uninitialized in this function
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The patch set is mostly driver updates (qla4, qla2 [ISF support updates],
lpfc, aacraid [dual firmware image support]) and a few bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRgAd8AAoJEDeqqVYsXL0Mg5wH/3P4wlXaRyqvyrFk1WSkmklZ
6YxzIKn/RLFmJlJvkaTT7N02ble2UqTluB6+5+AorU/jqz6DArxHsPnyv0/+2pXS
zYmp1hrcLn9dB3sZ2Y32jU2GlzHq+LSJSjjnUrA/uRrq1KTP09KCJtGbZUkvy710
x1/3e3I8u2bvBAehUkKvazg5+xlw/XImJ+IVXgUWOyiv1mNbqNEtT5qYt7sjnhLu
Mg2VfKTSb+kzxSpol3v51vh/wqY6unVcI/a9HxanihkDtkqRBRhg8wXpNAYI2xNK
uNLGq0VFpyCYfBZX0aqh01QZ++EUU2TNlRreVg4/crQnBR88EI3KtUsA1BOthwQ=
=x6dL
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James "Jej B" Bottomley:
"The patch set is mostly driver updates (qla4, qla2 [ISF support
updates], lpfc, aacraid [dual firmware image support]) and a few bug
fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
[SCSI] iscsi_tcp: support PF_MEMALLOC/__GFP_MEMALLOC
[SCSI] libiscsi: avoid unnecessary multiple NULL assignments
[SCSI] qla4xxx: Update driver version to 5.03.00-k8
[SCSI] qla4xxx: Added print statements to display AENs
[SCSI] qla4xxx: Use correct value for max flash node entries
[SCSI] qla4xxx: Restrict logout from boot target session using session id
[SCSI] qla4xxx: Use correct flash ddb offset for ISP40XX
[SCSI] isci: add CONFIG_PM_SLEEP to suspend/resume functions
[SCSI] scsi_dh_alua: Add module parameter to allow failover to non preferred path without STPG
[SCSI] qla2xxx: Update the driver version to 8.05.00.03-k.
[SCSI] qla2xxx: Obtain loopback iteration count from bsg request.
[SCSI] qla2xxx: Add clarifying printk to thermal access fail cases.
[SCSI] qla2xxx: Remove duplicated include form qla_isr.c
[SCSI] qla2xxx: Enhancements to support ISPFx00.
[SCSI] qla4xxx: Update driver version to 5.03.00-k7
[SCSI] qla4xxx: Replace dev type macros with generic portal type macros
[SCSI] scsi_transport_iscsi: Declare portal type string macros for generic use
[SCSI] qla4xxx: Add flash node mgmt support
[SCSI] libiscsi: export function iscsi_switch_str_param
[SCSI] scsi_transport_iscsi: Add flash node mgmt support
...
Use correct value for max flash node entries supported
based on adapter type.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use correct flash ddb offset to add and delete flash target
entries for ISP40XX
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch allows iscsiadm to manage iSCSI target information stored on
qla4xxx adapter flash on per host basis.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While probe Skip retry of initialize_adapter only for ISP82XX and ISP83XX.
We need to retry initialize_adapter for ISP40XX.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
If flash read for FLT fails, we are assigning wrong default
address for CHAP table in FLT, which will cause CHAP table
read/write to wrong address.
Fix:
Assign correct default CHAP table address to FLT.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Request queue count holds the information about free space in request queue
which has to be manipulated based on request in and out pointer.
But in driver response path, this count was incremented unconditionally,
which could move req_in pointer beyond req_out pointer.
This scenario leads fw hang during IO.
Solution:
Request queue count manipulation has to be done in IO path only, keeping
req_in and req_out pointer two IOCB count away
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move "Incorrect function ID" print message in case INTX interrupt
from DEBUG2 to DEBUG7. This will avoid floods of this message if
DEBUG2 is enabled.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use function int_to_scsilun() in qla4xxx_reset_lun() to convert
integer value comming from scsi_transport to scsi LUN address format.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In case of firmware hung we need to call "mailbox_premature_completion" to
complete any pending mbox command as firmware is not alive.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For ISP83XX set graceful reset bit in IDC_DRV_CTRL
if reset is issued by application
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
ISP83XX check is missing in function get_fw_boot_info() because of this
qla4xxx will not export boot target to sysfs and iscsistart cannot issue
login to boot target.
Fix:
Added check for ISP83XX in function get_fw_boot_info()
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem Description:
Disabling pause frames might cause hardware wedging needing a power cycle.
This might happen if the Eport is not initialized and is in reset.
Solution:
Before disabling pause frames ensure that eport is out of reset.
Signed-off-by: Manish Dusane <manish.dusane@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The error path calls dma_pool_free() on this path but "chap_table" is
NULL and "chap_dma" is uninitialized. It's cleaner to just return
directly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While reading sysfs chap_in_idx and chap_out_idx attribute, if chap
authentication is not set we get an error as "Invalid argument".
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Boot from SAN fails in some cases where boot target login response
is slow. In this case, probe finishes early and triggers init, which
doesn't find remote disk to mount root which leads to BFS failure.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch force driver to collect firmware dump using following command:-
"echo 2 > /sys/class/scsi_host/hostX/device/fw_dump"
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem:
If initialization of adapter fails for some reason, then the interrupt handlers
are released. The interrupt handlers are not registered again when initialization
of adapter is retried.
Solution:
Re-register the interrupt handler when adapter initialization is retried.
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem:
QLA4xxx firmware may assert if given more IOCBs than it can handle.
Solution:
The driver was updated to throttle the number of active IOCBs based
on the total number of IOCB buffers received from get_firmware_status
mbx_sts[2].
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Removed unnecessary calls to qla4xxx_get_firmware_status from
function qla4xxx_init_local_data
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Quiesce all different activities performed by driver upon the link events
while loopback diagnostics is in progress.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The spurious interrupt messages are seen when interrupt lines are
shared between different adapters or modules. Example, interrupt
lines are shared between qlcnic and qla4xxx and USB modules, then the
console is flooded with flurry of spurious interrupt messages
which are expected in such scenario.
Hence put these messages under debug level 2 for INTx interrupt mode.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Check mbox_sts[3] instead of mbox_sts[4] for ISP83xx to validate size
of data returned
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In qla4xxx_get_ep_fwdb(), dst_addr is of type struct sockaddr.
We are copying sizeof(struct sockaddr_in6) bytes to dst_addr
which is 12 bytes larger. This will cause memory corruption.
So we change dst_addr to struct sockaddr_storage which is
of 128 byte, large enough to hold sizeof(struct sockaddr_in6).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Reset operation fails if port is in Link Down state
Fix:
Do not wait till HBA comes online after reset command is invoked.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
Mailbox command timed out after switching from polling mode to interrupt mode.
Events:-
1. Mailbox interrupts are disabled
2. FW generates AEN and at same time driver enables Mailbox Interrupt
3. Driver issues new mailbox to Firmware
In above case driver will not get AEN interrupts generated by FW in step #2 as
FW generated this AEN when interrupts are disabled. During the same time
driver enabled the mailbox interrupt, so driver will not poll for interrupt.
Driver will never process AENs generated in step #2 and issues new mailbox to
FW, but now FW is not able to post mailbox completion as AENs generated before
are not processed by driver.
Fix:
Enable Mailbox / AEN interrupts before initializing FW in case of ISP83XX.
This will make sure we process all Mailbox and AENs in interrupt mode.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a large set of updates, mostly for drivers (qla2xxx [including support
for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape
adding virtually unlimited numbers of tape drives plus a set of dif fixes for
sd and a fix for a live lock on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
=49u9
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing (Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround) (Yinghai Lu)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=haBu
-----END PGP SIGNATURE-----
Merge tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Protect acpi_pci_drivers and acpi_pci_roots (Taku Izumi)
- Clear host bridge resource info to avoid issue when releasing
(Yinghai Lu)
- Notify acpi_pci_drivers when hot-plugging host bridges (Jiang Liu)
- Use standard list ops for acpi_pci_drivers (Jiang Liu)
Device hotplug
- Use pci_get_domain_bus_and_slot() to close hotplug races (Jiang
Liu)
- Remove fakephp driver (Bjorn Helgaas)
- Fix VGA ref count in hotplug remove path (Yinghai Lu)
- Allow acpiphp to handle PCIe ports without native hotplug (Jiang
Liu)
- Implement resume regardless of pciehp_force param (Oliver Neukum)
- Make pci_fixup_irqs() work after init (Thierry Reding)
Miscellaneous
- Add pci_pcie_type(dev) and remove pci_dev.pcie_type (Yijing Wang)
- Factor out PCI Express Capability accessors (Jiang Liu)
- Add pcibios_window_alignment() so powerpc EEH can use generic
resource assignment (Gavin Shan)
- Make pci_error_handlers const (Stephen Hemminger)
- Cleanup drivers/pci/remove.c (Bjorn Helgaas)
- Improve Vendor-Specific Extended Capability support (Bjorn
Helgaas)
- Use standard list ops for bus->devices (Bjorn Helgaas)
- Avoid kmalloc in pci_get_subsys() and pci_get_class() (Feng Tang)
- Reassign invalid bus number ranges (Intel DP43BF workaround)
(Yinghai Lu)"
* tag 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (102 commits)
PCI: acpiphp: Handle PCIe ports without native hotplug capability
PCI/ACPI: Use acpi_driver_data() rather than searching acpi_pci_roots
PCI/ACPI: Protect acpi_pci_roots list with mutex
PCI/ACPI: Use acpi_pci_root info rather than looking it up again
PCI/ACPI: Pass acpi_pci_root to acpi_pci_drivers' add/remove interface
PCI/ACPI: Protect acpi_pci_drivers list with mutex
PCI/ACPI: Notify acpi_pci_drivers when hot-plugging PCI root bridges
PCI/ACPI: Use normal list for struct acpi_pci_driver
PCI/ACPI: Use DEVICE_ACPI_HANDLE rather than searching acpi_pci_roots
PCI: Fix default vga ref_count
ia64/PCI: Clear host bridge aperture struct resource
x86/PCI: Clear host bridge aperture struct resource
PCI: Stop all children first, before removing all children
Revert "PCI: Use hotplug-safe pci_get_domain_bus_and_slot()"
PCI: Provide a default pcibios_update_irq()
PCI: Discard __init annotations for pci_fixup_irqs() and related functions
PCI: Use correct type when freeing bus resource list
PCI: Check P2P bridge for invalid secondary/subordinate range
PCI: Convert "new_id"/"remove_id" into generic pci_bus driver attributes
xen-pcifront: Use hotplug-safe pci_get_domain_bus_and_slot()
...
