imx_uart_set_termios() called imx_uart_rts_active(), or
imx_uart_rts_inactive() before taking port->port.lock.
As a consequence, sport->port.mctrl that these functions modify
could have been changed without holding port->port.lock.
Moved locking of port->port.lock above the calls to fix the issue.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time the DMA engine signals a transaction error the driver prints
a message at error level. Getting transaction errors is pretty much
expected on baudrate mismatches and the correspoding error counters
are increased in this case properly. Remove the error message which
is possibly repeated at a very high rate which can lock up the whole
system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ipg clock only needs to be unprepared in case preparing
per clock fails. The ipg clock has already disabled at the point.
Fixes: 1cf93e0d54 ("serial: imx: remove the uart_console() check")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2015 when irda was dropped from the driver imx1 was broken. This
change reintroduces the support for the third interrupt of the UART.
Fixes: afe9cbb1a6 ("serial: imx: drop support for IRDA")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some i.MX SoCs' low power mode, such as i.MX7D's LPSR(low power
state retention), UART iomux settings will be lost, need to add
pinctrl sleep/default mode switch during suspend/resume to make
sure UART iomux settings are correct after resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In noirq suspend/resume stage with no_console_suspend enabled,
imx_uart_console_write() may be called to print out log_buf
message by printk(), so there will be race condition between
imx_uart_console_write() and imx_uart_save/restore_context(),
need to add lock to protect the registers save/restore operations.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the program enters the uart ISR, the local interrupt has been
disabled by the system, so it's not appropriate to use spin_lock_irqsave
interface in the ISR.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct to check the right rx dma cookie status in spit of it
works because only one cookie is running in the current sdma.
But it will not once sdma driver support multi cookies
running based on virt-dma.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially when register shadowing was introduced (commit 3a0ab62f43
("serial: imx: implement shadow registers for UCRx and UFCR")) the logic
to handle UCR2_SRST was wrong but documented consistently. Later the
handling was fixed, but the comment was not. This change makes up leeway
for the latter.
Fixes: 0aa821d846 ("serial: imx: fix cached UCR2 read on software reset")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCR4_OREN is (depending on the configuration) enabled in startup,
but is never disabled. Fix this by disabling it in shutdown.
Reported-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Documentation/serial/driver the shutdown function should
not disable RTS, so drop it.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This properly unmaps DMA SG on device shutdown.
Reported-by: Nandor Han <nandor.han@ge.com>
Suggested-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unrelated CTSC/CTS disabling from imx_uart_disable_dma() and
move it to imx_uart_shutdown(), which is the only user of the DMA
disabling function. This should not change the driver's behaviour,
but improves readability. After this change imx_uart_disable_dma()
does the reverse thing of imx_uart_enable_dma().
Suggested-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To reset the UART the SRST needs be cleared (low active). According
to the documentation the bit will remain active for 4 module clocks
until it is cleared (set to 1).
Hence the real register need to be read in case the cached register
indicates that the SRST bit is zero.
This bug lead to wrong baudrate because the baud rate register got
restored before reset completed in imx_flush_buffer.
Fixes: 3a0ab62f43 ("serial: imx: implement shadow registers for UCRx and UFCR")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using half-duplex mode (which disables receiver during txing)
the RTS signal cannot be driven low during transmission when using
i.MX UART RTS/CTS control. This seems to be a limitation of the
i.MX UART IP: The RTS (CTS_B) signal is controlled by the receiver.
When the receiver is disabled, the signal stays in UART logic idle
state which is high...
If SER_RS485_RTS_ON_SEND is used, RTS needs to be high active during
transmission. Since this is the default state of the RTS (CTS_B)
signal when the receiver is off, half-duplex mode in this
configuration works fine.
However, a low-active RTS signal (flag SER_RS485_RTS_ON_SEND not set)
cannot be generated when the receiver is turned off.
Print an error if the user selects this unsupported configuration
(both SER_RS485_RTS_ON_SEND and SER_RS485_RX_DURING_TX unset) and
configure the closest working configuration (set the
SER_RS485_RX_DURING_TX flag).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a fixed prefix helps at several places. It ensures that another
driver doesn't use the same function name which confuses the linker and
tools like ctags. It simplifies working with function tracing and
dynamic printk() support which can filter on function names. And last
but not least it helps the human source code reader to understand if a
given function belongs to a driver or a more general part of the kernel.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial_core might call the .start_tx callback without any data being
available to send. In this case return early instead of going through
all the setup needed for sending which might include disabling RX in
RS485 half-duplex mode.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RS485 half duplex the Transmitter Complete irq is needed to
determine the moment when the transmitter can be disabled. When using
DMA this irq must only be enabled when DMA has completed to transfer all
data. Otherwise the CPU might busily trigger this irq which is not
properly handled and so the also pending irq for the DMA transfer cannot
trigger.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows to increase the RX waterlevel which allows to delay the RRDY
irq. The desired effect is that less irqs are needed to handle
characters and so reduce irq count of the system.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that UCR1.RXDMAEN and UCR1.ATDMAEN (for the DMA case) and
UCR1.RRDYEN (for the PIO case) are off iff UCR1.RXEN is disabled. This
ensures that the fifo isn't read with RX disabled which results in an
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the UART is used in DMA mode, .stop_rx() does nothing if the port
isn't suspended. This is wrong as .stop_rx() should stop receiving
characters unconditionally. When the port is about to be closed the DMA
channel is stopped in .shutdown(), so this isn't necessary to be in
.stop_rx() here, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aging timer fires if there are characters in the RX fifo but the
water level isn't reached yet. Make sure that the waterlevel is
configured before the aging timer is enabled to trigger a DMA request
(UCR1_ATDMAEN).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial/imx driver is full of inconsistently named and typed
variables that hold different register values.
Consistently use u32 as type (matching what readl and writel use) and
name the variables after the register whose value they are holding.
This makes it easier to notice when UCR2_RTSEN is written to UCR1.
The only difference introduced by this commit in the compiled driver is
that twice the second argument to warn_slowpath_null() changed because the
two WARN_ON in dma_rx_callback() pass __LINE__ to warn_slowpath_null().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original code looks as follows:
if (sport->dma_is_enabled) {
... make sure TX DMA is running, i.e. .dma_is_txing = 1
}
if (sport->dma_is_txing)
return;
As .dma_is_txing can only be true if .dma_is_enabled is, the return can
go at the end of the first if body without an additional check.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neither .dma_is_txing nor .dma_is_rxing can evaluate to true if
.dma_is_enabled evaluates to false:
The only function that sets .dma_is_txing to a non-zero value is
imx_dma_tx() which is only called if .dma_is_enabled is true. Same for
.dma_is_rxing and start_rx_dma(). And before .dma_is_enabled is set to 0
when imx_shutdown calls imx_disable_dma(), .dma_is_rxing and
.dma_is_txing are reset to zero before, too.
For this reason
sport->dma_is_enabled && sport->dma_is_rxing
has the same value as
sport->dma_is_rxing
which allows to simplify three if conditions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reduces the amount of read accesses to the register space by
shadowing the values for five registers that only change on writing
them. There is a single bit in UCR2 that might change without being
written to it, this is handled accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This prepares implementing shadow copies for the control registers and
additionally provides a good place to hook in debug code to trace
register usage.
Most of this patch was done using pattern substitution:
perl -p -i -e '
s/\breadl(?:_relaxed)?\((?:sport->port\.|port->)membase \+/imx_uart_readl(sport,/;
s/\bwritel(?:_relaxed)?\(([^,]*), (sport->port\.|port->)membase \+/imx_uart_writel(sport, $1,/;
' drivers/tty/serial/imx.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consistently indicate being called with irqs off and the port lock taken
for all functions that this applies to.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only the reference manual for the i.MX1 (I have MC9328MX1RM/D Rev 5 from
2004) uses TDMAEN and RDMAEN for these. All reference manuals for the
newer chips use TXDMAEN and RXDMAEN. Update to the newer name with the
assumption that most imx users don't use an imx1 any more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The imx_ports[] array is indexed using a value derived from the
"serialN" alias in DT, or from platform data, which may lead to an
out-of-bounds access.
Fix this by adding a range check.
Fixes: ff05967a07 ("serial/imx: add of_alias_get_id() reference back")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_shutdown() calls imx_disable_dma if .dma_is_enabled. So after
imx_shudown() completes, .dma_is_enabled is zero. For this reason
.dma_is_enabled is also zero when imx_startup() is called. So the check
for this variable being zero can be dropped.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .dma_is_inited member is only set to a value != 0 when the port's
startup function calls imx_uart_dma_init(). On shutdown of the port
imx_uart_dma_exit is called which sets the value back to 0. So
.dma_is_inited is always 0 when imx_startup() is called (assuming
.startup() and .shutdown() are correctly balanced) and the check for
!sport->dma_is_inited can go away.
This allows to replace .dma_is_inited by a variable local to
imx_startup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling an irq that isn't enabled can have some undesired side effects.
Some of these are mentioned in the newly introduced code comment. Some
of the irq sources already had their handling right, some don't. Handle
them all in the same consistent way.
The change for USR1_RRDY and USR1_AGTIM drops the check for
dma_is_enabled. This is correct as UCR1_RRDYEN and UCR2_ATEN are always
off if dma is enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the variable holding the value of register USR1 is called usr1
instead of sts which is more straight forward. The same is also done for
sts2 which is called usr2 now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check sts & USR1_DTRD was just evaluated to true two lines above.
So this change doesn't have any effect on the semantic of the driver.
Fixes: 27e1650105 ("serial: imx: implement DSR irq handling for DTE mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only one of the two is really required, not both:
* have_rtscts or
* have_rtsgpio
In imx_rs485_config() this is done correctly, so RS485 is working,
just the error message is false.
Signed-off-by: Phil Eichinger <phil@zankapfel.net>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: b8f3bff057 ("serial: imx: Support common rs485 binding for RTS polarity"
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows me to login after sending a break when service
serial-getty@ttymxc0.service is running
The "tty_insert_flip_char(port, 0, TTY_BREAK)" in clear_rx_errors
fixes this by allowing the higher layers to see a break.
Also, call uart_handle_break to handle possible
"secure attention key."
FYI: Martin said the ROM sdma firmware works with this patch,
but external sdma firmware still does not send breaks on a
i.mx6UL
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Martin Hicks <mort@bork.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before we go into suspend mode, we enable the imx uart's interrupt for
the awake bit in the UART Status Register 1. If, for some reason, the
awake bit is already set before we enter suspend mode, we get an
interrupt immediately when we enable interrupts for awake. The uart's
clk_ipg is disabled at this point (unless there's an ongoing transfer).
We end up in the interrupt handler, which usually tries to clear the
awake bit. This doesn't work with the clock disabled. Therefore, we
keep getting interrupts forever, resulting in an endless loop.
Clear the awake bit before setting the awaken bit to signal that we want
an imx interrupt when the awake bit will be set. This ensures that we're
not woken up by events that happened before we started going into
suspend mode.
Change the clock handling so that suspend prepares and enables the clock
and suspend_noirq disables it. Revert these operations in resume_noirq and
resume.
With these preparations in place, we can now modify awake and awaken in
the suspend function when the actual imx interrupt is disabled and the
required clk_ipg is active.
Update the thaw and freeze functions to use the new clock handling since
we share the suspend_noirq function between suspend and hibernate.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wakeup mechanism via RTSDEN bit relies on the system using the RTS/CTS
lines, so only allow such wakeup method when the system actually has
RTS/CTS support.
Fixes: bc85734b12 ("serial: imx: allow waking up on RTSD")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoke the ->rs485_config callback on probe to adjust the initial RTS
polarity based on the UART's device properties.
This implicitly fixes a bug: If RTS control is not available, rs485
should be disabled even if it was enabled through a device property.
Log an error when that occurs.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a driver invokes the uart_get_rs485_mode() helper, set the RTS
polarity to active high by default unless the newly introduced
"rs485-rts-active-low" property was specified.
imx contains a line to set the default RTS polarity to active high,
it is now superfluous and hence deleted.
omap-serial historically defaults to active low and supports an
"rs485-rts-active-high" property to inverse the polarity.
Retain that behavior for compatibility.
Cc: Mark Jackson <mpfj@newflow.co.uk>
Cc: Michał Oleszczyk <oleszczyk.m@gmail.com>
Cc: Rafael Gago Castano <rgc@hms.se>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ef838a81dd ("serial: Add common rs485 device tree parsing
function") consolidated retrieval of rs485 OF properties in a common
helper function but did not #ifdef it to CONFIG_OF. The function is
therefore included on ACPI platforms as well even though it's not used.
On the other hand ACPI platforms with rs485 do exist (e.g. Siemens
IOT2040) and they may leverage _DSD to store rs485 properties. Likewise,
UART platform devices instantiated from an MFD should be able to specify
rs485 properties. In fact, the tty subsystem maintainer had asked for
a "generic" function during review of commit ef838a81dd:
https://marc.info/?l=linux-serial&m=150143441725194&w=4
Thus, instead of constraining the helper to OF platforms, make it
platform-agnostic by converting it to device_property_*() functions
and renaming it accordingly.
In imx.c, move the invocation of uart_get_rs485_mode() from
serial_imx_probe_dt() to serial_imx_probe() so that it also gets called
for non-OF devices.
In omap-serial.c, move its invocation further up within
serial_omap_probe_rs485() so that the RTS polarity can be overridden
with the driver-specific "rs485-rts-active-high" property once we
introduce a generic "rs485-rts-active-low" property.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since imx_disable_rx_int is only called by imx_startup,
let's integrate it into that function. Notice UCR2_ATEN is
never set by the driver. The bit is still cleaned to make
this patch a noop.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
