Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.
Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are two reasons for this.
First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.
Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().
We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.
Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.
skb->xmit_more is retained (but always 0) to not cause build breakage.
This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions. Remaining drivers are converted in the next patches.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copy the ntuple feature into list of user selectable features.
Enable the ntuple feature.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for statistics and show basic counters.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add show and configure network flow classification (NFC) methods
to the ethtool. Show the specifies Rx ntuple filters.
Configures receive network flow classification option or rules.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable the multi queues to receive.
Program the direction of packets to specified queues according
to the mode selected in the MRQC register.
Multiple receive queues defined by filters and RSS for 4 queues.
Enable/disable RSS hashing and also to enable multiple receive queues.
This patch will allow further ethtool support development.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size is not necessary, hence
it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic ethtool support to the device to allow
for configuration.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Address community comment.
Remove obsolete IGC_ERR define and use dev_err method.
Suggested by Joe Perches.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While reviewing code, I noticed that Eric Dumazet recommends that
drivers check the return code of napi_complete_done, and use that
to decide to enable interrupts or not when exiting poll. One of
the Intel drivers was already fixed (ixgbe).
Upon looking at the Intel drivers as a whole, we are handling our
polling and NAPI exit in a few different ways based on whether we
have multiqueue and whether we have Tx cleanup included. Several
drivers had the bug of exiting NAPI with return 0, which appears
to mess up the accounting in the stack.
Consolidate all the NAPI routines to do best known way of exiting
and to just mostly look like each other.
1) check return code of napi_complete_done to control interrupt enable
2) return the actual amount of work done.
3) return budget immediately if need NAPI poll again
Tested the changes on e1000e with a high interrupt rate set, and
it shows about an 8% reduction in the CPU utilization when busy
polling because we aren't re-enabling interrupts when we're about
to be polled.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Address few community comments.
Remove unused code, will be added per demand.
Remove blank lines and unneeded includes.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I just cleaned up a couple small white space issues.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to netif_set_real_num_tx_queues is not assigning the error
return to variable err even though the next line checks err for an
error. Fix this by adding the missing err assignment.
Detected by CoverityScan, CID#1474551 ("Logically dead code")
Fixes: 3df25e4c1e ("igc: Add interrupt support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/intel/igc/igc_main.c: In function 'igc_probe':
drivers/net/ethernet/intel/igc/igc_main.c:3535:11: warning:
variable 'pci_using_dac' set but not used [-Wunused-but-set-variable]
It never used since introduction in commit
d89f88419f ("igc: Add skeletal frame for Intel(R) 2.5G Ethernet Controller support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Many of the Intel Ethernet drivers call skb_tx_timestamp() earlier than
necessary. Move the calls to this function to the latest point possible,
just prior to notifying hardware of the new Tx packet when we bump the
tail register.
This affects i40e, iavf, igb, igc, and ixgbe.
The e100, e1000, e1000e, fm10k, and ice drivers already call the
skb_tx_timestamp() function just prior to indicating the Tx packet to
hardware, so they do not need to be changed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add link establishment methods
Add auto negotiation methods
Add read MAC address method
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add PHY's ID support
Add support for initialization, acquire and release of PHY
Enable register access
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code for NVM support and get MAC address, complete probe
method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code for hardware initialization and reset
Add code for semaphore handling
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for allocating, configuring, and freeing Tx/Rx ring
resources. With these changes in place the descriptor queues are in a
state where they are ready to transmit or receive if provided buffers.
This also adds the transmit and receive fastpath and interrupt handlers.
With this code in place the network device is now able to send and receive
frames over the network interface using a single queue.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds the defines and structures necessary to support both Tx
and Rx descriptor rings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch set adds interrupt support for the igc interfaces.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have the ability to configure the basic settings on the device
we can start allocating and configuring a netdev for the interface.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the basic defines and structures needed by the PF for
operation. With this it is possible to bring up the interface,
but without being able to configure any of the filters on
the interface itself.
Add skeleton for a function pointers.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the beginning framework onto which I am going to add
the igc driver which supports the Intel(R) I225-LM/I225-V 2.5G
Ethernet Controller.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
