OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.
This patch removes the use of SRAM as video ram for the old omapfb
driver to simplify memory handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
OMAP SRAM can be used as video memory on OMAP1 and 2. However, there
usually is very little SRAM available, thus limiting its use, and no
board supported by the kernel currently uses it.
This patch removes the use of SRAM as video ram for the omapdss driver
to simplify memory handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Old omapfb driver (drivers/video/omap/) is no longer used for OMAP2+
devices, and thus we can remove OMAP2+ support from it and make it an
OMAP1 omapfb driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
N8x0's blizzard driver has been ported to new omapdss driver, so we can
now remove the old blizzard driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Rather than accessing GPSR and GPCR directly, use the GPIO subsystem
instead.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GPIO set and clear registers should only be written, rather than
read, modified, and written. A read-modify-write will have undesired
side effects.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sa1100fb driver needs to set the GPIO direction and alternate
function register according to the panel that we're driving. We've
done this in the driver by read-modify-writing the register, which
may cause problems with races. Fix this with a minimal change.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the LCD information is available while the driver is loaded,
we don't need to cache that information into our driver private data
structure. Get rid of it.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the assabet specific initialization for PAL output mode -
we call the lcd_power function before we enable the LCD controller,
which will disable the LCD panel to prevent it receiving incorrect
timings. Therefore, this setup here is redundant.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we have platform data contained within the individual board
code, we can get rid of the global function pointers, placing them
inside the platform data instead.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move platform data out of the sa1100fb driver into the various
platform files themselves.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the LCD data structures to an include file which can be shared
with the board code in arch/arm/mach-sa1100.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the sa1100fb_mach_info structure to carry the RGB bitfield
overrides, rather than requiring them to be separately initialized
in sa1100fb_get_machine_info().
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the dev_xxx() macros for driver kernel message output, rather than
open coded printk() with KERN_ levels etc. Remove DPRINTK().
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The rgb structures should only be read and never written. Constify
them.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Annotate the driver structure with the .owner field, to allow the
module to be associated with the driver.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: drivers/video/built-in.o(.devinit.text+0x58): Section mismatch in reference from the function sa1100fb_probe() to the function .init.text:sa1100fb_init_fbinfo()
The function __devinit sa1100fb_probe() references
a function __init sa1100fb_init_fbinfo().
If sa1100fb_init_fbinfo is only used by sa1100fb_probe then
annotate sa1100fb_init_fbinfo with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x258): Section mismatch in reference from the function sa1100fb_init_fbinfo() to the (unknown reference) .init.data:(unknown)
The function __devinit sa1100fb_init_fbinfo() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sa1100fb_init_fbinfo then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x26c): Section mismatch in reference from the function sa1100fb_init_fbinfo() to the (unknown reference) .init.data:(unknown)
The function __devinit sa1100fb_init_fbinfo() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sa1100fb_init_fbinfo then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x270): Section mismatch in reference from the function sa1100fb_init_fbinfo() to the (unknown reference) .init.data:(unknown)
The function __devinit sa1100fb_init_fbinfo() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sa1100fb_init_fbinfo then
annotate (unknown) with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x278): Section mismatch in reference from the function sa1100fb_init_fbinfo() to the (unknown reference) .init.data:(unknown)
The function __devinit sa1100fb_init_fbinfo() references
a (unknown reference) __initdata (unknown).
If (unknown) is only used by sa1100fb_init_fbinfo then
annotate (unknown) with a matching annotation.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Obviously this is a typo and although there were no effects observed
it's probably better to fix it.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The MCLK mode defines a factor to divide the clock that is used to
generate the Audio Clock Regeneration packets, MCLK.
The divisor is not used when the CTS value is calculated by HW.
When the value is calculated by SW, it depends on the silicon
revision.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the MCLK is used to drive the Audio Clock Regeneration packets,
the initialization procedure is to set ACR_CTRL[2] to 0 and then
back again to 1. Also, devices that do not support the MCLK, use
the TMDS clock directly by leaving ACR_CTRL[2] set to 0.
The MLCK clock divisor, mclk_mode, is configured only if MLCK
is used. Such configuration is no longer related to the CTS mode
as in some silicon revisions CTS SW-mode is used along with the MCLK.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Certain OMAP4 revisions (i.e., 4430 ES2.3, 4460, and 4470) use
a pseudo clock (generated from the TMDS clock), MCLK, to drive the
generation of Audio Clock Regeneration packets. Other devices
(i.e., 4430 ES2.[0,2]) use the TMDS clock directly.
This patch adds a new DSS feature for MCLK support. It also rearranges
the omap_dss_features structures to reflect the devices supporting it.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Over time better gamma has been determined and tuned with some
equipment so update the defaults. From subjective point of view
dark shades should be better visible.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
During system suspend, at the time DSS is being suspended, SPI is
already suspended and it's clocks are cut. Because of this trying to
communicate with the LCD controller results in a deadlock.
To fix this, split out LCD programming parts of display enable/disable
functions and perform them from SPI PM callbacks instead when system is
being suspended. If the display is just being enabled/disabled, do it
from DSS callbacks as before.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With AVI infoframe various parameters of video stream such as
aspect ratio, quantization range, videocode etc will be indicated
from source to sink.Thus AVI information needs to be set/accessed
by the middle ware based on the video content.
Thus this parameter is now moved to the ip_data structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for Innolux AT080TN52 800x600 panel.
Tested with AM3517 based board.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The calculation of required DISPC_FCLK for downscaling is done by multplying the
pixel clock with an integer factor. This isn't true for OMAP4 where the required
clock is calculated using the exact ratio of downscaling done.
Fix this calculation for OMAP4. Also, do a minor clean up of calc_fclk().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The number of dss_feat_id members has increased to a large value, the current
way of assigning a subset of these features (for a particular OMAP) as a mask
is no longer feasible.
Maintain the subset of features supported as lists. Make the function
dss_has_feature() traverse through this list.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that dss is using devm_ functions for allocation in probe functions,
small reordering of the allocations allows us to clean up the probe
functions more.
This patch moves "unmanaged" allocations after the managed ones, and
uses plain returns instead of gotos where possible. This lets us remove
a bunch of goto labels, simplifying the probe's error handling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We should handle the allocation here, if only to keep the static
checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This is a resurrection of an old (like 2.4.19) out-of-tree driver for
Intel740 graphics cards and adaptation for recent kernels. The old driver by
Andrey Ulanov is located at: http://sourceforge.net/projects/i740fbdev/files/
This is a new driver based on skeletonfb, using most of the low level HW code
from the old driver. The DDC code is completely new.
The driver was tested on two 8MB cards: Protac AG240D and Diamond Stealth II
G460.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds support for using EDID data on CRT and DVP1 for
initial configuration if viafb_mode or viafb_mode1 are not present.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Samsung EXYNOS SoC such Exynos5 has DP controller and embedded DP
panel can be used. This patch supports DP driver based on Samsung
EXYNOS SoC chip.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
An moled panel driver based MIPI DSI interface. S6E8AX0 means it may
includes many other ldi controllers, for example, S6E8AA0, S6E8AB0, and so
on.
This patch can be modified depending on each panel properites. For
example, second parameter of panel condition register can be changed
depending on ldi controller or amoled type.
[akpm@linux-foundation.org: fix Kconfig syntax error]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Samsung S5PC210 and EXYNOS SoC platform has MIPI-DSI controller and
MIPI-DSI based LCD Panel could be used with it. This patch supports
MIPI-DSI driver based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
machine code and LCD panel driver specific function registered to
mipi_dsim_ddi structure at lcd panel init function called system init. In
the MIPI-DSI driver, find lcd panel driver by using registered lcd panel
name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Patch calculates pixel clock period in pico seconds and updates
the same in variable screen information structure. fbset utility
uses this information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix several -Wuninitialized compiler warnings by changing the
order of getting modedb in riva_update_default_var() to set
first the fallback and then the prefered timing.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fixes the I2C emulation on GPIO ports by enabling it
(software controlled) and disabling the output on a GPIO line before
reading it.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch implementes this mode (viafb_SAMM_ON set and
viafb_dual_fb not set) in a useful way for CRT and DVI devices.
The same content is shown on both devices in different video modes.
The first (primary) resolution must not be bigger than the secondary
one and determines the visible region. The same content is shown
centered on the secondary output.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fills xres and yres in var which is required when a
temporary var is genereated when viafb_SAMM_ON is set and
viafb_dual_fb is not set. It also removes an obsolete comment.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch sets the correct polarity for the second adapter when
viafb_SAMM_ON is set and viafb_dual_fb is not set. Just one step to
make this mode useful.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds the basic infrastructure and a few stub drivers for
devices that are connected via I2C busses. The infrastructure will
be used to replace and extend the support that is scattered
throughout viafb. The stub drivers are not very useful yet but they
show how the infrastructure works, provide information about the
chips integrated into a system and maybe gather some testers as it
would be very difficult for a single person to get a sane test
environment.
The only thing this actually does is probing the I2C busses which
will hopefully not cause any regressions.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It includes:
- a compile fix for fsl-diu-fb
- a fix for a suspend/resume issue in atmel_lcdfb
- a fix for a suspend/resume issue in OMAP
- a workaround for a hardware bug to avoid physical damage in OMAP
- a really trivial dead code removal in intelfb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=2uP4
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3
It includes:
- compile fix for fsl-diu-fb
- fix for a suspend/resume issue in atmel_lcdfb
- fix for a suspend/resume issue in OMAP
- workaround for a hardware bug to avoid physical damage in OMAP
- really trivial dead code removal in intelfb
* tag 'fbdev-fixes-for-3.3-1' of git://github.com/schandinat/linux-2.6:
atmel_lcdfb: fix usage of CONTRAST_CTR in suspend/resume
intelfb: remove some dead code
drivers/video: compile fixes for fsl-diu-fb.c
OMAPDSS: HDMI: PHY burnout fix
OMAP: 4430SDP/Panda: add HDMI HPD gpio
OMAP: 4430SDP/Panda: setup HDMI GPIO muxes
OMAPDSS: remove wrong HDMI HPD muxing
OMAP: 4430SDP/Panda: rename HPD GPIO to CT_CP_HPD
OMAP: 4430SDP/Panda: use gpio_free_array to free HDMI gpios
OMAPDSS: use sync versions of pm_runtime_put
This patch converts the drivers in drivers/video/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Roger Quadros <roger.quadros@nokia.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds video clock running at data under-flow.
It means that the pixel clock is continuously provided
to lcd module, even when under-run occurs.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds alpha value width setting according to
transparency value of each window format, using BLENDCON
register. When alpha value is 8 bits, BLENDCON will set
alpha value width as 8 bits.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fixes the checkpatch error listed below:
ERROR: trailing statements should be on next line
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
In au1100fb.c, the probe function now returns -ENODEV on failure.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The USB graphics card driver delays the unregistering of the framebuffer
device to a workqueue, which breaks the userspace visible remove uevent
sequence. Recent userspace tools started to support USB graphics card
hotplug out-of-the-box and rely on proper events sent by the kernel.
The framebuffer device is a direct child of the USB interface which is
removed immediately after the USB .disconnect() callback. But the fb device
in /sys stays around until its final cleanup, at a time where all the parent
devices have been removed already.
To work around that, we remove the sysfs fb device directly in the USB
.disconnect() callback and leave only the cleanup of the internal fb
data to the delayed work.
Before:
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb0 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
remove /2-1.2:1.0/graphics/fb0 (graphics)
After:
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
add /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb1 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/graphics/fb1 (graphics)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0 (usb)
remove /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2 (usb)
Cc: stable@vger.kernel.org
Tested-by: Bernie Thompson <bernie@plugable.com>
Acked-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Saves some code, especially useful as the code saved is mostly in the
infrequently tested error paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
LCDC functional clock may or may not be derived from CPU/MPU DPLL,
For example,
AM335x => Separate independent DPLL for LCDC
Davinci => Same DPLL as MPU
So, on platforms where LCDC functional clock is not derived from CPU/MPU
PLL it is not required to reset LCDC module as its functional clock does
not change with DVFS.
This patch adds check to do reset only if functional clock changes
between pre and post notifier callbacks with DVFS.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Allow framebuffer to be configured in 16bit mode when panel is wired in
(the default) BGR configuration, and don't claim to support 15bit input
modes, which the LCD controller cannot handle.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
An error was existing in the saving of CONTRAST_CTR register
across suspend/resume.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The goto on the line before means the return is unreachable. The goto
also returns -ENODEV so no changes are needed there.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix a compiler errors introduced in:
commit ddd3d90543
Author: Timur Tabi <timur@freescale.com>
drivers/video: fsl-diu-fb: merge all allocated data into one block
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss doesn't work properly on system suspend. The problem seems to be
the fact that omapdss uses pm_runtime_put() functions when turning off
the hardware, and when system suspend is in process only sync versions
are allowed.
Using non-sync versions normally and sync versions when suspending would
need rather ugly hacks to convey the information of
suspending/not-suspending to different functions. Optimally the driver
wouldn't even need to care about this, and the PM layer would handle
syncing when suspend is in process.
This patch changes all omapdss's pm_runtime_put calls to
pm_runtime_put_sync. This fixes the suspend problem, and probably the
performance penalty of always using sync versions is negligible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit ba02fa37de disabled the
venc driver registration on OMAP4. Since the driver never gets
probed/initialised your get a dereferenceed NULL pointer if you
try to get info from /sys/kernel/debug/omapdss/venc
Return info message about disabled venc if venc_dump_regs() gets called.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Due to changes in struct hdmi_config, the pixel clock has to be obtained
differently.
The pixel clock is needed to calculate the CTS value as defined in the
HDMI specification.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
code and mode parameters are already a part of the ip_data structure
so no need to keep the same parameters again in hdmi global structure.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change the timing match logic, Instead of the statically mapped method
to get the corresponding timings for a given code and mode, move to a
simpler array indexed method. It will help to scale up to add more
timings when needed.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the vsync polarity, hsync polarity, interlace to hdmi_video_timings.
Remove the now duplicate structure hdmi_timings.
update the static table structure in HDMI with CEA/VESA code and mode.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
video interface structure is a duplicate structure with parameters which are
already present in ip_data config structure, Thus removing the structure and
modifying corresponding code.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Take fifo merge into use by implementing a rather naive fifo merge
threshold calculation: keep the low threshold always the same, but
increase the high threshold when fifo merge is used.
This should greatly increase the time between pixel data fetches from
SDRAM, as the usable fifo size is much larger. However, it probably
won't help for fifo underflows, as the low threshols is kept the same.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fifo thresholds are calculated using bytes, but the debug print prints
values in buffer units. Change the prints to use bytes to be in line
with the calculations, and also to print in the same units on all OMAPs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add fifo-merge support. This is done mainly in four functions:
mgr_enable/disable and ovl_enable/disable. These are the functions where
overlays are taken into and out of active use.
The process to enable and disable fifo-merge is not simple. We need to
do it in steps, waiting in between for certain settings to be taken into
use, and continuing after that. The reason for this is that fifo-merge
is a common thing for all managers/overlays, and its use must be
synchronized.
As an example, when we disable an overlay, we first set the overlay as
disabled, then wait until the overlay is actually disabled in the HW,
and only after that we may re-configure the fifos, possibly taking
fifo-merge into use.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add mechanism to set/unset the DISPC fifo-merge:
Add new fields to dss_data, fifo_merge and fifo_merge_dirty. These are
similar to the other info/dirty flags in ovl_priv_data and ovl_mgr_data,
but fifo merge is a common attribute to all managers and thus outside
the ovl_mgr_data.
The fifo-merge field is used in the dss_write_regs_common, which handles
writing the register.
dss_apply_fifo_merge() can be used to set/unset the fifo merge field in
the dss_data.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add feature flag for fifo merge. OMAP2 doesn't contain fifo merge, later
OMAPs do.
dispc_enable_fifomerge() checks for the flag when called, and gives a
WARN if fifo merge is being enabled when it is not supported.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alberto Panizzo <alberto@amarulasolutions.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to write new value if the bit mask fields of new value is not
equal to old value. It does not make sense to write new value only when
all the bit_mask bits are zero.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
macfb won't init in black & white modes since fb_alloc_cmap() no longer
works for zero cmap length. Fix this and also clean up a few printk's and
some stylistic inconsistencies.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'fbdev-next' of git://github.com/schandinat/linux-2.6: (175 commits)
module_param: make bool parameters really bool (drivers/video/i810)
Revert "atmel_lcdfb: Adjust HFP calculation so it matches the manual."
OMAPDSS: HDMI: Disable DDC internal pull up
OMAPDSS: HDMI: Move duplicate code from boardfile
OMAPDSS: add OrtusTech COM43H4M10XTC display support
OMAP: DSS2: Support for UMSH-8173MD TFT panel
ASoC: OMAP: HDMI: Move HDMI codec trigger function to generic HDMI driver
OMAPDSS: HDMI: Create function to enable HDMI audio
ASoC: OMAP: HDMI: Correct signature of ASoC functions
ASoC: OMAP: HDMI: Introduce driver data for audio codec
grvga: fix section mismatch warnings
video: s3c-fb: Don't keep device runtime active when open
video: s3c-fb: Hold runtime PM references when touching registers
video: s3c-fb: Take a runtime PM reference when unblanked
video: s3c-fb: Disable runtime PM in error paths from probe
video: s3c-fb: Use s3c_fb_enable() to enable the framebuffer
video: s3c-fb: Make runtime PM functional again
drivers/video: fsl-diu-fb: merge fsl_diu_alloc() into map_video_memory()
drivers/video: fsl-diu-fb: add default platform ops functions
drivers/video: fsl-diu-fb: remove broken reference count enabling the display
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HHrh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
pvr2fb special cases its init/exit routines which causes spurious section
mismatches. Set the board_driver array __refdata to silence them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Dan Carpenter points out that it's an int, not a bool:
intelfbdrv.c:818: if (bailearly == 1)
intelfbdrv.c:828: if (bailearly == 2)
intelfbdrv.c:836: if (bailearly == 3)
intelfbdrv.c:842: if (bailearly == 4)
intelfbdrv.c:851: if (bailearly == 5)
intelfbdrv.c:859: if (bailearly == 6)
intelfbdrv.c:866: bailearly > 6 ? bailearly - 6 : 0);
intelfbdrv.c:874: if (bailearly == 18)
intelfbdrv.c:886: if (bailearly == 19)
intelfbdrv.c:893: if (bailearly == 20)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This reverts commit 5d910426a6.
Nicolas Ferre <nicolas.ferre@atmel.com> wrote:
"Unfortunately this is not true for all the SoC that embed the
atmel_lcdfb... So I may need to rework this patch but it is certainly
not applicable in the current form."
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Andrew elucidates:
- First installmeant of MM. We have a HUGE number of MM patches this
time. It's crazy.
- MAINTAINERS updates
- backlight updates
- leds
- checkpatch updates
- misc ELF stuff
- rtc updates
- reiserfs
- procfs
- some misc other bits
* akpm: (124 commits)
user namespace: make signal.c respect user namespaces
workqueue: make alloc_workqueue() take printf fmt and args for name
procfs: add hidepid= and gid= mount options
procfs: parse mount options
procfs: introduce the /proc/<pid>/map_files/ directory
procfs: make proc_get_link to use dentry instead of inode
signal: add block_sigmask() for adding sigmask to current->blocked
sparc: make SA_NOMASK a synonym of SA_NODEFER
reiserfs: don't lock root inode searching
reiserfs: don't lock journal_init()
reiserfs: delay reiserfs lock until journal initialization
reiserfs: delete comments referring to the BKL
drivers/rtc/interface.c: fix alarm rollover when day or month is out-of-range
drivers/rtc/rtc-twl.c: add DT support for RTC inside twl4030/twl6030
drivers/rtc/: remove redundant spi driver bus initialization
drivers/rtc/rtc-jz4740.c: make jz4740_rtc_driver static
drivers/rtc/rtc-mc13xxx.c: make mc13xxx_rtc_idtable static
rtc: convert drivers/rtc/* to use module_platform_driver()
drivers/rtc/rtc-wm831x.c: convert to devm_kzalloc()
drivers/rtc/rtc-wm831x.c: remove unused period IRQ handler
...
Should be no functional changes, mainly a reorganisation to support future
work.
[akpm@linux-foundation.org: fix CONFIG_PM=n build]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Saves some error handling code and eliminates a class of leaks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The usage of simple_strtoul() or strict_strtoul() is not preferred. Thus,
kstrtoul should be used.
This patch also fixes checkpatch error as follows:
ERROR: space required after that ',' (ctx:VxV)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
module.h is included twice.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch supports regulator power control in the driver. Current ld9040
driver was controlled power on/off sequence by callback function in the
board file. But, by doing this, there's no need to register lcd power
on/off callback function in the board file.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the drivers in drivers/video/backlight/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> [ep93xx_bl.c]
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support for the Avionic Design Xanthos backlight device got added in
commit 3b96ea9ef8 ("backlight: Add support for the Avionic Design Xanthos
backlight device."). That support depends on ARCH_PXA_ADX. The code that
should have provided that Kconfig symbol never got submitted. It has
never been possible to even build this driver. Remove it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'stable/for-linus-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (37 commits)
xen/pciback: Expand the warning message to include domain id.
xen/pciback: Fix "device has been assigned to X domain!" warning
xen/pciback: Move the PCI_DEV_FLAGS_ASSIGNED ops to the "[un|]bind"
xen/xenbus: don't reimplement kvasprintf via a fixed size buffer
xenbus: maximum buffer size is XENSTORE_PAYLOAD_MAX
xen/xenbus: Reject replies with payload > XENSTORE_PAYLOAD_MAX.
Xen: consolidate and simplify struct xenbus_driver instantiation
xen-gntalloc: introduce missing kfree
xen/xenbus: Fix compile error - missing header for xen_initial_domain()
xen/netback: Enable netback on HVM guests
xen/grant-table: Support mappings required by blkback
xenbus: Use grant-table wrapper functions
xenbus: Support HVM backends
xen/xenbus-frontend: Fix compile error with randconfig
xen/xenbus-frontend: Make error message more clear
xen/privcmd: Remove unused support for arch specific privcmp mmap
xen: Add xenbus_backend device
xen: Add xenbus device driver
xen: Add privcmd device driver
xen/gntalloc: fix reference counts on multi-page mappings
...
Another simple series related to clock management, this time only for
imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=czKE
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9 ("net/fec: fix the .remove code").
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (466 commits)
net/hyperv: Add support for jumbo frame up to 64KB
net/hyperv: Add NETVSP protocol version negotiation
net/hyperv: Remove unnecessary kmap_atomic in netvsc driver
staging/rtl8192e: Register against lib80211
staging/rtl8192e: Convert to lib80211_crypt_info
staging/rtl8192e: Convert to lib80211_crypt_data and lib80211_crypt_ops
staging/rtl8192e: Add lib80211.h to rtllib.h
staging/mei: add watchdog device registration wrappers
drm/omap: GEM, deal with cache
staging: vt6656: int.c, int.h: Change return of function to void
staging: usbip: removed unused definitions from header
staging: usbip: removed dead code from receive function
staging:iio: Drop {mark,unmark}_in_use callbacks
staging:iio: Drop buffer mark_param_change callback
staging:iio: Drop the unused buffer enable() and is_enabled() callbacks
staging:iio: Drop buffer busy flag
staging:iio: Make sure a device is only opened once at a time
staging:iio: Disallow modifying buffer size when buffer is enabled
staging:iio: Disallow changing scan elements in all buffered modes
staging:iio: Use iio_buffer_enabled instead of open coding it
...
Fix up conflict in drivers/staging/iio/adc/ad799x_core.c (removal of
module_init due to using module_i2c_driver() helper, next to removal of
MODULE_ALIAS due to using MODULE_DEVICE_TABLE instead).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (185 commits)
powerpc: fix compile error with 85xx/p1010rdb.c
powerpc: fix compile error with 85xx/p1023_rds.c
powerpc/fsl: add MSI support for the Freescale hypervisor
arch/powerpc/sysdev/fsl_rmu.c: introduce missing kfree
powerpc/fsl: Add support for Integrated Flash Controller
powerpc/fsl: update compatiable on fsl 16550 uart nodes
powerpc/85xx: fix PCI and localbus properties in p1022ds.dts
powerpc/85xx: re-enable ePAPR byte channel driver in corenet32_smp_defconfig
powerpc/fsl: Update defconfigs to enable some standard FSL HW features
powerpc: Add TBI PHY node to first MDIO bus
sbc834x: put full compat string in board match check
powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
powerpc: Fix unpaired probe_hcall_entry and probe_hcall_exit
offb: Fix setting of the pseudo-palette for >8bpp
offb: Add palette hack for qemu "standard vga" framebuffer
offb: Fix bug in calculating requested vram size
powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
powerpc/44x: Fix build error on currituck platform
powerpc/boot: Change the load address for the wrapper to fit the kernel
powerpc/44x: Enable CRASH_DUMP for 440x
...
Fix up a trivial conflict in arch/powerpc/include/asm/cputime.h due to
the additional sparse-checking code for cputime_t.
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dd data for the OrtusTech COM43H4M10XTC display to the
generic_dpi_panel driver.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds support for Microtip Technologies' UMSH-8173MD 800x480
RGB TFT panel. Tested with an OMAP3 board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[tomi.valkeinen@ti.com: changed the panel name string]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function hdmi_audio_trigger is a callback used by ASoC to stop/start
HDMI audio. Also, it does not perform IP-specific configuration directly.
Hence, it should be placed in the general portion of the HDMI driver,
along with the other ASoC callbacks.
Also, make this function static.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to separate clearly IP-specific code from general DSS code,
a function for OMAP4 audio enable is created. This function is
included in the HDMI IP ops to align with the current implementation
of the DSS HDMI driver. This function is to be used by the ASoC
HDMI audio codec.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These functions require access to IP-secific data. However, it is not possible
to pass such data as a function argument as such functions have a specific
signature specified by ASoC. Instead, they will have access to the IP-specific
data by calling snd_soc_codec_get_drvdata. The codec driver data is set
at probe time.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Under the new DSS architecture for HDMI, there is a clear separation
between general DSS code and HDMI IP-specific data. Functions
that require access to the HDMI driver IP-specific data receive an
hdmi_ip_data structure. The ASoC codec require access to such
IP-specific data. Then, instead of accessing it directly, it will be
passed as codec driver data. This also helps to have a clear separation
between DSS and ASoC portions of the code.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The 'name', 'owner', and 'mod_name' members are redundant with the
identically named fields in the 'driver' sub-structure. Rather than
switching each instance to specify these fields explicitly, introduce
a macro to simplify this.
Eliminate further redundancy by allowing the drvname argument to
DEFINE_XENBUS_DRIVER() to be blank (in which case the first entry from
the ID table will be used for .driver.name).
Also eliminate the questionable xenbus_register_{back,front}end()
wrappers - their sole remaining purpose was the checking of the
'owner' field, proper setting of which shouldn't be an issue anymore
when the macro gets used.
v2: Restore DRV_NAME for the driver name in xen-pciback.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fix following section mismatch warnings:
WARNING: drivers/video/built-in.o(.devinit.text+0x110): Section mismatch in reference from the function grvga_probe() to the function .init.text:grvga_parse_custom()
The function __devinit grvga_probe() references
a function __init grvga_parse_custom().
If grvga_parse_custom is only used by grvga_probe then
annotate grvga_parse_custom with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x1f8): Section mismatch in reference from the function grvga_probe() to the variable .init.data:grvga_fix
The function __devinit grvga_probe() references
a variable __initdata grvga_fix.
If grvga_fix is only used by grvga_probe then
annotate grvga_fix with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x204): Section mismatch in reference from the function grvga_probe() to the variable .init.data:grvga_fix
The function __devinit grvga_probe() references
a variable __initdata grvga_fix.
If grvga_fix is only used by grvga_probe then
annotate grvga_fix with a matching annotation.
grvga_fix is used in a function annotated __devinit - so
match this using a __devinitdata annotation on grvga_fix.
grvga_parse_custom() is used in a function annotated
__devinit - so match this by annotating grvga_parse_custom()
with __devinit too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Allow the controller to be runtime suspended when the screen is blanked
by not taking a runtime reference while the device is open. This allows
greater system wide power savings when used with a standard application
layer and ensures that the screen does not blank unless requested.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Take a runtime PM reference whenever updating registers in preparation
for suspending the device when the framebuffer is blanked.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
When the framebuffer is unblanked hold a runtime PM reference. This
prevents us powering down when userspace has left an image on the
framebuffer and prepares the way for being able to power down the hardware
when an application still has the device open.
Since we now hold a runtime PM reference whenever the display is unblanked
there is no need for the runtime power management to disable and enable
the display, and doing so would lead to runtime PM trying to recurse into
itself when called from the blanking code, so split the runtime PM into
separate functions which only deal with the clocks. The PM core will
runtime resume the device prior to system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The s3c-fb driver has a function called s3c_fb_enable() which turns on
and off the physical output. However it is only actually used in paths
which disable the screen, the enabling just writes to the register. Make
the code less confusing by ensuring that the enable also goes through
the same path.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The change in "video: s3c-fb: modify runtime pm functions" (commit
35784b) renders the runtime power management for the device completely
ineffectual as while it leaves runtime power management notionally
enabled a runtime power reference is held for the entire time the device
is registered meaning it will never actually do anything.
A further issue is introduced as runtime power management is added
during the system suspend path which is not something which drivers are
supposed to do and would interact poorly if there were any operations
done in the runtime power management callbacks.
While this does make things simpler (the main motivation for the
original change) it will not only cause us to use more power in the
framebuffer controller but will also prevent us entering lower power
domain and SoC wide states as we can never power down the domain
containing the device. Since neither of these things is desirable
revert the change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Functions fsl_diu_alloc() and fsl_diu_free() were only being called by
map_video_memory() and unmap_video_memory(), respectively.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The DIU driver requires some platform-specific functions to be defined,
but two them can be optional because most platforms implement them the
same way. Functions set_gamma_table() and get_pixel_format() are only
needed because of quirks in the Freescale MPC8610 HPCD reference board.
For other boards, a generic implementation works, so we shouldn't
require the platform code to define them.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The functions enable_lcdc() and disable_lcdc() used the variable fb_enable
to keep a reference count of when the display is enabled, but the code is
broken. The display is always disabled when disable_lcdc(), and it is
always enabled when enable_lcdc() is called, regardless of the value of
fb_enable. Obviously, we don't need to keep a reference count, so just
remove the variable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The DIU uses system RAM for the framebuffer, so FBINFO_VIRTFB should be set.
Since the framebuffer is in system RAM, it can be read from more quickly
than written to, so FBINFO_READS_FAST should be set.
We can also set FBINFO_PARTIAL_PAN_OK for the same reasons.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Function init_fbinfo() is called only from install_fb(), and it's only a few
lines long. Plus, it ignores the return code from fb_alloc_cmap(). Merge
its contents into install_fb() and handle errors properly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
When using a >8bpp framebuffer, offb advertises truecolor, not directcolor,
and doesn't touch the color map even if it has a corresponding access method
for the real hardware.
Thus it needs to set the pseudo-palette with all 3 components of the color,
like other truecolor framebuffers, not with copies of the color index like
a directcolor framebuffer would do.
This went unnoticed for a long time because it's pretty hard to get offb
to kick in with anything but 8bpp (old BootX under MacOS will do that and
qemu does it).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org
We rename the mach64 hack to "simple" since that's also applicable
to anything using VGA-style DAC IO ports (set to 8-bit DAC) and we
use it for qemu vga.
Note that this is keyed on a device-tree "compatible" property that
is currently only set by an upcoming version of SLOF when using the
qemu "pseries" platform. This is on purpose as other qemu ppc platforms
using OpenBIOS aren't properly setting the DAC to 8-bit at the time of
the writing of this patch.
We can fix OpenBIOS later to do that and add the required property, in
which case it will be matched by this change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We used to try to request 8 times more vram than needed, which would
fail if the card has a too small BAR (observed with qemu & kvm).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org
Clock requirements for scaling in OMAP2, OMAP3 and OMAP4 are different. In
OMAP2 and OMAP3 the required clock rate is a function of pixel clock, vertical
downscale ratio and horizontal downscale ratio whereas in OMAP4 it is a
function of pixel clock and horizontal downscale ratio only. Selection of 3-tap
vs 5-tap coefficients depends on clock rate line buffer width in OMAP3 whereas
in OMAP4 it is independent of clock rate and line buffer width. In OMAP2 3-tap
for vertical and 5-tap for horizontal scaling is used. In OMAP4 5-tap is used
both for horizontal and vertical scaling for better performance. Also, the
number and width of line buffers differs in OMAP3 and OMAP4.
So, clock functions have been fined tuned for OMAP3 and support has been added
added for OMAP4. This code has been tested on OMAP2, OMAP3 and OMAP4, and
scaling issues due to clock errors have been resolved.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The FIR coefficients present in kernel are being updated to new coefficients
consisting of 24 coefficient tables, with 12 each for 3 tap and 5 tap scenario,
which are chosen on the basis of DISPC up/downsampling filters M value. M is
the inverse of low pass cut off frequency of the sampling filter. For vertical
scaling 3 tap or 5 tap tables are used based on the clock rate and width of
the line buffer whereas in OMAP2 3 tap is always used. For horizontal scaling
however 5 tap tables are always used.
New coefficients and the corresponding logic have been tested on OMAP2, OMAP3
and OMAP4. Horizontal and vertical scaling worked fine except for some 3 tap
vs 5 tap issue during vertical upscaling and clock failing issues which is
acknowledged in the next patch. Vertical upscaling was found to perform better
under 5 taps. The 24 coefficient tables have been moved to another file
dispc_coefs.c for proper maintainance.
This code is written based on code written by Lajos Molnar <lajos@ti.com> in
Android Kernel for scaling. Lajos Molnar <lajos@ti.com> had fine tuned the FIR
coefficient selection process and reduced outliness and blockiness around
images when upscaling more than 2 times.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
extra_info_update_ongoing() goes through all overlays, but doesn't check
if the overlay is connected to a manager. This leads to a crash whenever
an overlay has been detached.
Add a check to skip the non-connected overlays.
Reported-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make PICODLP driver on OMAP2_DSS_DPI since it is the display interface it uses.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display state parameter of omap_dss_device struct is not being set correctly
in the panel driver NEC panel driver panel-nec-nl8048hl11-01b.c. Set the correct
states in the panel's enable/disable/suspend/resume functions.
CC: Erik Gilling <konkers@android.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The clock names of DSI_PLL_HSDIV_DISPC and DSI_PLL_HSDIV_DSI was made
dynamic based on the current value of DISPC and DSI FCLK sources. This
doesn't need to be done since we are just interested in the clock names,
and not the current clock sources for DISPC and DSI FCLKs.
Use only the generic and omap specific names for the DSI PLL's HSDIV
clocks.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions dss_ovl_simple_check() and dss_mgr_simple_check() are not
really part of the apply mechanism, and can be moved to overlay.c and
manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dispc's error handler tries to disable all outputs when OCP_ERR
happens. However, the code doesn't check if there actually is a display
on each particular output, nor if there's a driver for the display. This
may lead to NULL pointer reference.
Signed-off-by: Rob Clark <rob@ti.com>
[tomi.valkeinen@ti.com: added patch description]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch converts the drivers in drivers/video/omap/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Laurent Gonzalez <palmte.linux@free.fr>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These symbols are not used outside it's driver so no need to
make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The functions dss_ovl_check, dss_mgr_check_zorder, dss_mgr_check in
apply.c are not really part of the apply mechanism, and can be moved to
overlay.c and manager.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Don't use Amstrad Delta custom I/O functions any longer, use GPIO API
instead.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit fb21c2f428 ("fbdev: Add FOURCC-based format configuration API")
modified the layout of the fb_var_screeninfo structure. Remove zero
fields from the static initializers in the matroxfb driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add memory size detection for Virge/VX and small delay in mode setting (same
as in X.org driver) to fix blank screen problem.
Also adjust DTPC position to fix garbled screen in some modes (tested that
this adjustment does not break other cards - at least Trio32, Trio64V+,
Trio64V2/DX, Virge, Virge/DX).
Tested on ELSA Winner 2000AVI/3D.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The driver should be registered with mxsfb_driver, not with mxsfb_devtype.
This caused obvious null pointer dereference and crash.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Huang Shijie <b32955@freescale.com>
Acked-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The driver says "module_param(ddc3, bool, 0);". But it's not a used
as a bool, it's used as a count.
Make it a bool.
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch converts the drivers in drivers/video/pnx4008/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Grigory Tolstolytkin <gtolstolytkin@ru.mvista.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch converts mbxfb to use the module_platform_driver() macro
which makes the code smaller and a bit simpler.
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This API will be used to support YUV frame buffer formats in a standard
way.
Last but not least, create a much needed fbdev API documentation and
document the format setting APIs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
"machine_data" is too long and clunky, and the "machine" part doesn't make
much sense, anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Shadow registers should be protectd whenever the registers are
updated. Shadow registers are updated after SHADOWCON shadow
register is cleared.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Runtime suspend and runtime resume are modified in order to
reduce the complexity and improve the usability of runtime pm.
After probe function, s3c-fb driver is not suspended until
suspend or remove is called.
The scheme is changed as follows:
runtime_get is only called in probe and resume.
runtime_put is only called in remove and suspend.
open/close cannot call the runtime_get/put.
Also, runtime_susepnd/resume are just called by runtime pm,
not doing suspend/resume routine any longer. This is because
open/close cannot call the runtime_get/put; the suspend/resume
routine in runtime_suspend/resume were previously used when
open and close were called.
The name of s3c-fb dev_pm_ops is changed from s3cfb_pm_ops to
s3c_fb_pm_ops in order to use more consistent naming.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The Freescale DIU driver allocates multiple blocks of memory, including
multiple DMA buffers. Merge all of these blocks into one data structure.
Specifically:
1) struct fsl_diu_data now contains everything that needs to be allocated,
except for the framebuffers themselves. DMA'able objects are aligned correctly
within the structure.
2) struct diu_addr is no longer needed, because we don't have to manage
multiple blocks of DMA memory.
3) Since there's no diu_addr any more, macro DMA_ADDR is used to calculate
the DMA address of any field in fsl_diu_data.
4) Functions allocate_buf() and free_buf() are no longer needed, because we
now assume that dma_alloc_coherent() will allocate a page-aligned block,
and everything is properly aligned with fsl_diu_data already, so we no longer
need to align any memory blocks ourselves.
5) The "dummy" area descriptor is now defined separately from the other
five ADs, so NUM_AOIS (previously called FSL_AOI_NUM) is now set to five
instead of six. Previously, all six were combined together to avoid a
separate call to allocate_buf() just for the dummy AD.
6) framebuffer_alloc() and framebuffer_release() are no longer used. The
framebuffer is initialized manually.
7) Error handling is simplified since there's only one memory buffer
allocated.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch set missing bitmask of enabled hardware window which
should be checked whenever the hardware window is enabled.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This resolves the conflict in the
drivers/staging/iio/industrialio-core.c file due to two different
changes made to resolve the same problem.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The IPU internally works on 32bit colors. It can arbitrarily map
between pixel formats and internal representation and also between
internal representation and the physical connection to the display.
The driver used to change the mapping between internal representation
and display connection depending on the user selected bpp which is
wrong. Instead, the mapping is specified by the hardware, so an
additional field in platform data is added to describe the connection
between i.MX and the display. The default for this field is RGB666
which seems to be the only configuration which works without this
patch, so I assumed that all in Kernel boards are connected this
way.
This patch has been tested on a RGB666 connected display and a
RGB888 connected display in both 16bpp and 32bpp modes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
SGI IP22/IP28 machines have GIO busses for adding graphics and other
extension cards. This patch adds support for GIO driver/device
handling and converts the newport console driver to a GIO driver.
[ralf@linux-mips.org: Fixed build error caused by the modules.h -> export.h
changes.]
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
To: linux-fbdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2886/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.
Tested on DB1500 and DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the checkpatch errors listed below:
ERROR: do not initialise statics to 0 or NULL
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
WARNING: braces {} are not necessary for single statement blocks
WARNING: braces {} are not necessary for any arm of this statement
WARNING: static char array declaration should probably be static const char
WARNING: line over 80 characters
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The s3c-fb driver has separate runtime and system PM functions but the
implementations are identical so far as I can tell so unify them for
simplicity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch converts the drivers in drivers/video/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexey Charkov <alchark@gmail.com>
Acked-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Use framebuffer_alloc() instead of static fb_info and currentpar variables.
Also sanitize the error path and cleanup code (e.g. missing free_irq()).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Current code will always write fifo threshold values to the register,
even if they are the same as previously. Separate the setting of fifo
fields into a separate function, and only set new values if they are
different than the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently fifo threshold configuration is done per overlay or per
manager. However, when a fifo size configuration is added, we need to
always configure the thresholds for all overlays.
This patch prepares for that by changing the fifo threshold
configuration to always handle all overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When we are enabling an overlay, there's a point in time when the
overlay is not actually enabled yet (nor do we want it to be enabled),
but we do want to check if the configuration for the overlay is valid,
and to calculate correct fifo thresholds for the soon-to-be-enabled
overlay.
Current code handled this in a hacky way, setting op->enabled to true
temporarily when calling functions that need to consider the state when
the overlay is enabled.
This patch makes this a bit cleaner, adding "enabling" field, which is
set when the overlay is not yet enabled but should be considered in the
checks and calculations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently dss_write_regs() implicitely sets the GO bits for all managers
with shadow dirty flags set. This is a bit misleading, as one does not
presume "write registers" function to also set the GO bit.
Thus this patch splits the setting of GO bits into a separate function,
dss_set_go_bits, which is used after writing the registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In the apply irq handler the code currently clears the shadow dirty
flags whenever the manager in question is not busy (i.e. GO bit is
down). However, this is not quite right, as the GO bit may have never
been set.
While not done in the current code, the above would cause bug in
scenario where the registers are written, and thus shadow_dirty flag is
set, but the GO bit will be set only later. In this case the
shadow_dirty flags would be cleared, even if the HW is not using the new
configurations.
This patch fixes the issue by clearing the shadow flags only when the GO
bit is clear, and the GO bit had been set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
need_isr() should return true whenever there's work that needs to be
handled in the VSYNC/FRAMEDONE irq handler. However, need_isr() is
missing some cases where we need the irq handler.
This patch adds checks for shadow dirty flags, so that the irq handler
is started/kept running while shadow dirty flags are set.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
extra_info_update_ongoing() skipped checks for overlays that were marked
as disabled. This doesn't work, as the enable status of an overlay is in
the extra_info group, and thus extra_info_update_ongoing() reports false
when we are disabling an overlay. This causes
wait_pending_extra_info_updates() to not wait for the ongoing overlay
disable.
This patch changes extra_info_update_ongoing() to check the state of
overlays marked as disabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that dss_mgr_enable returns an error value, check it in all the
places dss_mgr_enable is used, and bail out properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add checks for overlay and manager settings. The checks are a bit
complex, as we need to observe the bigger picture instead of overlays
and managers independently. Things like the used display and the zorder
of other overlays affect the validity of the settings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_mgr_simple_check() which is used to check the validity of
certain manager attributes. Only attributes that can be checked
independently, without knowing the display being used, is done here
(thus "simple").
We can use this function in dss_mgr_set_info().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add dss_ovl_simple_check() which is used to check the validity of
certain overlay attributes. Only attributes that can be checked
independently, without knowing the display being used, is done here
(thus "simple").
We can use this function in dss_ovl_set_info().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
apply.c no longer touches any registers if an output is not enabled.
This means that we don't need to do dispc_runtime_get() anymore, and the
calls can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
