Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unplugging an r8152 adapter while the interface is UP, the NIC
becomes unusable. usb->disconnect (aka rtl8152_disconnect) deletes
napi. Then, rtl8152_disconnect calls unregister_netdev and that invokes
netdev->ndo_stop (aka rtl8152_close). rtl8152_close tries to
napi_disable, but the napi is already deleted by disconnect above. So
the first while loop in napi_disable never finishes. This results in
complete deadlock of the network layer as there is rtnl_mutex held by
unregister_netdev.
So avoid the call to napi_disable in rtl8152_close when the device is
already gone.
The other calls to usb_kill_urb, cancel_delayed_work_sync,
netif_stop_queue etc. seem to be fine. The urb and netdev is not
destroyed yet.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 driver handles TSO packets (limited to ~16KB) quite well,
but pretends each TSO logical packet is a single packet on the wire.
There is also some error since headers are accounted once, but
error rate is small enough that we do not care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set rx mode before calling netif_wake_queue() when linking on to avoid
the device missing the receiving packets.
The transmission may start after calling netif_wake_queue(), and the
packets of resopnse may reach before calling rtl8152_set_rx_mode()
which let the device could receive packets. Then, the packets of
response would be missed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device could only check the checksum of TCP and UDP packets. Therefore,
for the IPv4 packets excluding TCP and UDP, the check of checksum is necessary,
even though the IP checksum is correct.
Take ICMP for example, The IP checksum may be correct, but the ICMP checksum
may be wrong.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8153 on Dell TB15/16 dock corrupts rx packets.
This change is suggested by Realtek. They guess that the XHCI controller
doesn't have enough buffer, and their guesswork is correct, once the RX
aggregation gets disabled, the issue is gone.
ASMedia is currently working on a real sulotion for this issue.
Dell and ODM confirm the bcdDevice and iSerialNumber is unique for TB16.
Note that TB15 has different bcdDevice and iSerialNumber, which are not
unique values. If you still have TB15, please contact Dell to replace it
with TB16.
BugLink: https://bugs.launchpad.net/bugs/1729674
Cc: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This product is named 'TP-LINK USB 3.0 Gigabit Ethernet Network
Adapter (Model No.is UE300)'. It uses chip RTL8153 and works with
driver drivers/net/usb/r8152.c
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This linksys dongle by default comes up in cdc_ether mode.
This patch allows r8152 to claim the device:
Bus 002 Device 002: ID 13b1:0041 Linksys
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace VLAN_HLEN and CRC_SIZE with ETH_FCS_LEN.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move calling delay_autosuspend() in rtl8152_runtime_suspend(). Calling
delay_autosuspend() as late as possible.
The original flows are
1. check if the driver/device is busy now.
2. set wake events.
3. enter runtime suspend.
If the wake event occurs between (1) and (2), the device may miss it. Besides,
to avoid the runtime resume occurs after runtime suspend immediately, move the
checking to the end of rtl8152_runtime_suspend().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split rtl8152_resume() into rtl8152_runtime_resume() and
rtl8152_system_resume().
Besides, replace GFP_KERNEL with GFP_NOIO for usb_submit_urb().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add byte_enable for ocp_read_word() to replace reading 4
bytes data with reading the desired 2 bytes data.
This is used to avoid the issue which is described in
commit b4d99def09 ("r8152: remove sram_read"). The
original method always reads 4 bytes data, and it may
have problem when reading the PHY registers.
The new method is supported since RTL8153B, but it
doesn't influence the previous chips. The bits of the
byte_enable for the previous chips are the reserved
bits, and the hw would ignore them.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The settings of the new chip are the same with RTL8152, except that
its product ID is 0x8050.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting the device version out of the driver really aids debugging.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change from using napi_complete to napi_complete_done to allow for the
use of gro_flush_timeout in tuning network processing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop queuing rx packets if it is more than 1000.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use PLA 0xe000 bit 8 to check if disabling ALDPS is finished.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move tp->rtl_ops.init() from rtl8152_resume() to rtl8152_reset_resume().
The initialization is only necessary for reset_resume().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only RTL8153 could set coalesce, so move the default setting for
rtl8152_probe() to r8153_init().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use another way to keep disabling the U2P3 for both RTL_VER_03 and
RTL_VER_04.
Move enabling U2P3 from r8153_init() to r8153_hw_phy_cfg(). The
engineer ask the setting should be done after PHY settings.
Disable U2P3 first in rtl8153_up().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the order of rtl8153_runtime_enable() according to the
suggestion from the engineer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the setting from r8153_first_init() to r8153_init(). It only needs to
be set once.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC clock speed down could be enabled if the U1/U2 is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable lpm after r8153_init() and remove other enable/disable lpm.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use r8153_phy_status() to check phy status of RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since functions never returns meaningfull value.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is not used, removing it fixes the following warning when
building with clang:
drivers/net/usb/r8152.c:825:5: error: unused function 'usb_ocp_read'
[-Werror,-Wunused-function]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this the generic cdc_ether grabs the device,
and does not really work.
Signed-off-by: René Rebe <rene@exactcode.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linking status may be changed when autosuspend. And, after
autoresume, the driver may try to transmit packets when the device
is carrier off, because the interrupt transfer doesn't update the
linking status, yet. And, if the device is in ALDPS mode, the device
would stop working.
The another similar case is
1. unplug the cable.
2. interrupt transfer queue a work_queue for linking change.
3. device enters the ALDPS mode.
4. a tx occurs before the work_queue is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
revert commit a59e6d8152 ("r8152: correct the rx early size") and
fix the rx early size as
(rx buffer size - rx packet size - rx desc size - alignment) / 4
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the received maximum size (RMS) according to the mtu size. It is
unnecessary to receive a packet which is more than the size we could
transmit. Besides, this could let the rx buffer be used effectively.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check hw version first in probe(). Do nothing if the driver doesn't
support the chip.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list rx_done would be initialized when the linking on occurs.
Therefore, if a napi is scheduled without any linking on before,
the following kernel panic would happen.
BUG: unable to handle kernel NULL pointer dereference at 000000000000008
IP: [<ffffffffc085efde>] r8152_poll+0xe1e/0x1210 [r8152]
PGD 0
Oops: 0002 [#1] SMP
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace &tp->napi with napi and tp->netdev with netdev.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule the napi after napi_enable() for rx, if it is necessary.
If the rx is completed when napi is disabled, the sheduling of napi
would be lost. Then, no one handles the rx packet until next napi
is scheduled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-schedule napi after napi_complete() for tx, if it is necessay.
In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop the tx when the napi is disabled to prevent napi_schedule() is
called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the setting of the flag of SELECTIVE_SUSPEND to prevent start_xmit()
from calling napi_schedule() directly during runtime suspend.
After calling napi_disable() or clearing the flag of WORK_ENABLE,
scheduling the napi is useless.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Runtime suspend shouldn't be executed if the tx queue is not empty,
because the device is not idle.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152_post_reset() should sumbit rx urb and interrupt transfer,
otherwise the rx wouldn't work and the linking change couldn't be
detected.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
