Commit fd141d1a99 ("powerpc/powernv/pci: Rework accessing the TCE
invalidate register") broke TCE invalidation on IODA2/PHB3 for real
mode.
This makes invalidate work again.
Fixes: fd141d1a99 ("powerpc/powernv/pci: Rework accessing the TCE invalidate register")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We should return -ENOMEM if alloc_spu_gang() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This sets the type of the interrupt appropriately. We set it as follow:
- If not mapped from the device-tree, we use edge. This is the case
of the virtual interrupts and PCI MSIs for example.
- If mapped from the device-tree and #interrupt-cells is 2 (PAPR
compliant), we use the second cell to set the appropriate type
- If mapped from the device-tree and #interrupt-cells is 1 (current
OPAL on P8 does that), we assume level sensitive since those are
typically going to be the PSI LSIs which are level sensitive.
Additionally, we mark the interrupts requested via the opal_interrupts
property all level. This is a bit fishy but the best we can do until we
fix OPAL to properly expose them with a complete descriptor. It is also
correct for the current HW anyway as OPAL interrupts are currently PCI
error and PSI interrupts which are level.
Finally now that edge interrupts are properly identified, we can enable
CONFIG_HARDIRQS_SW_RESEND which will make the core re-send them if
they occur while masked, which some drivers rely upon.
This fixes issues with lost interrupts on some Mellanox adapters.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch utilises the GENERIC_CPU_AUTOPROBE infrastructure
to automatically load the crc32c-vpmsum module if the CPU supports
it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 817820b022 ("powerpc/iommu: Support "hybrid" iommu/direct DMA
ops for coherent_mask < dma_mask) adds a check of coherent_dma_mask for
dma allocations.
Unfortunately current PASemi code does not set this value for the DMA
engine, which ends up with the default value of 0xffffffff, the result
is on a PASemi system with >2Gb ram and iommu enabled the the onboard
ethernet stops working due to an inability to allocate memory. Add an
initialisation to pci_dma_dev_setup_pasemi().
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* x86 nested virt tweak and OOPS fix
* Simplify pvclock code (vdso bits acked by Andy Lutomirski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXpKOnAAoJEL/70l94x66D5z4H/R2660Vy3brQrI8lGxCtkXJt
AVe8PwI8nDfYJ/UkMZ2KcHPSvy+sHW2ydaZXYNqXHVBeTaUxiPW9rTgK61ebypGL
1tPOgJ3kGZF6XEdAz6gS8LniNFc+D3W6Y6sRylkEsqPj39/hxe7QMoOMSCQ9imbW
WMIx7/81i1EMw6oi+9FVtq+yHCpvyfFnD8t1TDsYWOReVn1J15SxbEs4Ih+hBMLz
HZ5DEjp9cAmzeR7GLje5eH1t6TEEoNb1MNgFWuscoAsDf8D9DKqRB9s0hC+TLFYn
oZbGSqjQwu3/VMblgedinH6X9MTm8V0zW29ToGnDcoO00AUmdlNmXSaZUhvT/Rs=
=H5cD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
- ARM bugfix and MSI injection support
- x86 nested virt tweak and OOPS fix
- Simplify pvclock code (vdso bits acked by Andy Lutomirski).
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
nvmx: mark ept single context invalidation as supported
nvmx: remove comment about missing nested vpid support
KVM: lapic: fix access preemption timer stuff even if kernel_irqchip=off
KVM: documentation: fix KVM_CAP_X2APIC_API information
x86: vdso: use __pvclock_read_cycles
pvclock: introduce seqcount-like API
arm64: KVM: Set cpsr before spsr on fault injection
KVM: arm: vgic-irqfd: Workaround changing kvm_set_routing_entry prototype
KVM: arm/arm64: Enable MSI routing
KVM: arm/arm64: Enable irqchip routing
KVM: Move kvm_setup_default/empty_irq_routing declaration in arch specific header
KVM: irqchip: Convey devid to kvm_set_msi
KVM: Add devid in kvm_kernel_irq_routing_entry
KVM: api: Pass the devid in the msi routing entry
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.8. Also includes is a
minor SSB cleanup as SSB code traditionally is merged through the MIPS
tree:
ATH25:
- MIPS: Add default configuration for ath25
Boot:
- For zboot, copy appended dtb to the end of the kernel
- store the appended dtb address in a variable
BPF:
- Fix off by one error in offset allocation
Cobalt code:
- Fix typos
Core code:
- debugfs_create_file returns NULL on error, so don't use IS_ERR for
testing for errors.
- Fix double locking issue in RM7000 S-cache code. This would only
affect RM7000 ARC systems on reboot.
- Fix page table corruption on THP permission changes.
- Use compat_sys_keyctl for 32 bit userspace on 64 bit kernels.
David says, there are no compatibility issues raised by this fix.
- Move some signal code around.
- Rewrite r4k count/compare clockevent device registration such that
min_delta_ticks/max_delta_ticks files are guaranteed to be
initialized.
- Only register r4k count/compare as clockevent device if we can
assume the clock to be constant.
- Fix MSA asm warnings in control reg accessors
- uasm and tlbex fixes and tweaking.
- Print segment physical address when EU=1.
- Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO.
- CP: Allow booting by VP other than VP 0
- Cache handling fixes and optimizations for r4k class caches
- Add hotplug support for R6 processors
- Cleanup hotplug bits in kconfig
- traps: return correct si code for accessing nonmapped addresses
- Remove cpu_has_safe_index_cacheops
Lantiq:
- Register IRQ handler for virtual IRQ number
- Fix EIU interrupt loading code
- Use the real EXIN count
- Fix build error.
Loongson 3:
- Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES
Octeon:
- Delete built-in DTB pruning code for D-Link DSR-1000N.
- Clean up GPIO definitions in dlink_dsr-1000n.dts.
- Add more LEDs to the DSR-100n DTS
- Fix off by one in octeon_irq_gpio_map()
- Typo fixes
- Enable SATA by default in cavium_octeon_defconfig
- Support readq/writeq()
- Remove forced mappings of USB interrupts.
- Ensure DMA descriptors are always in the low 4GB
- Improve USB reset code for OCTEON II.
Pistachio:
- Add maintainers entry for pistachio SoC Support
- Remove plat_setup_iocoherency
Ralink:
- Fix pwm UART in spis group pinmux.
SSB:
- Change bare unsigned to unsigned int to suit coding style
Tools:
- Fix reloc tool compiler warnings.
Other:
- Delete use of ARCH_WANT_OPTIONAL_GPIOLIB"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (61 commits)
MIPS: mm: Fix definition of R6 cache instruction
MIPS: tools: Fix relocs tool compiler warnings
MIPS: Cobalt: Fix typo
MIPS: Octeon: Fix typo
MIPS: Lantiq: Fix build failure
MIPS: Use CPHYSADDR to implement mips32 __pa
MIPS: Octeon: Dlink_dsr-1000n.dts: add more leds.
MIPS: Octeon: Clean up GPIO definitions in dlink_dsr-1000n.dts.
MIPS: Octeon: Delete built-in DTB pruning code for D-Link DSR-1000N.
MIPS: store the appended dtb address in a variable
MIPS: ZBOOT: copy appended dtb to the end of the kernel
MIPS: ralink: fix spis group pinmux
MIPS: Factor o32 specific code into signal_o32.c
MIPS: non-exec stack & heap when non-exec PT_GNU_STACK is present
MIPS: Use per-mm page to execute branch delay slot instructions
MIPS: Modify error handling
MIPS: c-r4k: Use SMP calls for CM indexed cache ops
MIPS: c-r4k: Avoid small flush_icache_range SMP calls
MIPS: c-r4k: Local flush_icache_range cache op override
MIPS: c-r4k: Split r4k_flush_kernel_vmap_range()
...
Pull x86 fixes from Ingo Molnar:
"Two fixes and a cleanup-fix, to the syscall entry code and to ptrace"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/syscalls/64: Add compat_sys_keyctl for 32-bit userspace
x86/ptrace: Stop setting TS_COMPAT in ptrace code
x86/vdso: Error out if the vDSO isn't a valid DSO
support for the J-Core J2 processor, an open source synthesizable
reimplementation of the SH-2 ISA, resolve a longstanding sigcontext
ABI mismatch issue, and fix various bugs including nommu-specific
issues and minor regressions introduced in 4.6.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJXpQweAAoJELcQ+SIFb8Ha2vgH/Rm3YTHEgGeQhRvBle8DTPNv
l9xBCQ6UMVb9T8C5nyP0jdioAVDQr7gh7sv2c7inIjN8hQh16DXFtNV8X6G3b0jv
OC0+rBmcYjpO7gGC/L2sRE8ghuNpoIBJFojZy6bwOIvpF6EDMAZ9bAU/VFbY28so
nCUdEo0gAmrdqGyHRfEJke7D7AKPvpAnN/cmRcvNQPhkkzKjRSNg5rHLthmvAKyp
1ChASb3YYPTgOY09izD8JUp4rk7v7q2smpgfeZfGQhIN/w6QKpv5OIqe+vrm1iKU
B6q5gBHS7Y2VYilp1zKQedLM9ZthH6rnpkB25RzyH655uTwf//6ihyP3kEwlPkc=
=wwNa
-----END PGP SIGNATURE-----
Merge tag 'sh-for-4.8' of git://git.libc.org/linux-sh
Pull arch/sh updates from Rich Felker:
"These changes improve device tree support (including builtin DTB), add
support for the J-Core J2 processor, an open source synthesizable
reimplementation of the SH-2 ISA, resolve a longstanding sigcontext
ABI mismatch issue, and fix various bugs including nommu-specific
issues and minor regressions introduced in 4.6.
The J-Core arch support is included here but to be usable it needs
drivers that are waiting on approval/inclusion from their subsystem
maintainers"
* tag 'sh-for-4.8' of git://git.libc.org/linux-sh: (23 commits)
sh: add device tree source for J2 FPGA on Mimas v2 board
sh: add defconfig for J-Core J2
sh: use common clock framework with device tree boards
sh: system call wire up
sh: Delete unnecessary checks before the function call "mempool_destroy"
sh: do not perform IPI-based cache flush except on boards that need it
sh: add SMP support for J2
sh: SMP support for SH2 entry.S
sh: add working futex atomic ops on userspace addresses for smp
sh: add J2 atomics using the cas.l instruction
sh: add AT_HWCAP flag for J-Core cas.l instruction
sh: add support for J-Core J2 processor
sh: fix build regression with CONFIG_OF && !CONFIG_OF_FLATTREE
sh: allow clocksource drivers to register sched_clock backends
sh: make heartbeat driver explicitly non-modular
sh: make board-secureedge5410 explicitly non-modular
sh: make mm/asids-debugfs explicitly non-modular
sh: make time.c explicitly non-modular
sh: fix futex/robust_list on nommu models
sh: disable aliased page logic on NOMMU models
...
- Fix HugeTLB leak due to CoW and PTE_RDONLY mismatch
- Avoid accessing unmapped FDT fields when checking validity
- Correctly account for vDSO AUX entry in ARCH_DLINFO
- Fix kallsyms with absolute expressions in linker script
- Kill unnecessary symbol-based relocs in vmlinux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJXpFZ5AAoJELescNyEwWM0PI4IALsTuHRzClOSMDLiqMUj8t+5
WNAcqybxAjCOVxAHckhweju++TeJBxcRH1nvBoNwiHIdHTv4fq1TZ3PeEq9kWMg5
JbKjYjvd9dW8k6LXMya8iXCYtG3kzbNejkNpOTVebC86yvas1IiEjNb/ztPdhJeM
HBSOkhfk8RcskfNxhuscZzGXbbdH9/R+XSTNRHN/RwCZH8PlInmduD9BbMvDhZyP
NLFonD2IgQ4as1kYG/HdIcw0BamHiURjd043+gyoqMvm7JjPksRzlQnr91SMkX17
LykXjHYPi2Me3aTrZ1NtkUNd5FHLHZ6/b9Wg6nA19d5KWkd3ER9uSJqGxkkbnt0=
=dtGK
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- fix HugeTLB leak due to CoW and PTE_RDONLY mismatch
- avoid accessing unmapped FDT fields when checking validity
- correctly account for vDSO AUX entry in ARCH_DLINFO
- fix kallsyms with absolute expressions in linker script
- kill unnecessary symbol-based relocs in vmlinux
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix copy-on-write referencing in HugeTLB
arm64: mm: avoid fdt_check_header() before the FDT is fully mapped
arm64: Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO
arm64: relocatable: suppress R_AARCH64_ABS64 relocations in vmlinux
arm64: vmlinux.lds: make __rela_offset and __dynsym_offset ABSOLUTE
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in
one of the OPP framework's helper functions (Jisheng Zhang).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WvPB
-----END PGP SIGNATURE-----
Merge tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"A few more fixes and cleanups in the x86-64 low-level hibernation
code, PM core, cpufreq (Kconfig and intel_pstate), and the operating
points framework.
Specifics:
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in one
of the OPP framework's helper functions (Jisheng Zhang)"
* tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
PM-wakeup: Delete unnecessary checks before three function calls
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup rtc-cmos,
rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after shutdown for QNAP
TS-41x
- s3c: clock fixes
-----BEGIN PGP SIGNATURE-----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=rpGB
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
* pm-sleep:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
* pm-cpufreq:
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
* pm-core:
PM-wakeup: Delete unnecessary checks before three function calls
* pm-opp:
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
Fixes:
- Fix early access to cpu_spec relocation from Benjamin Herrenschmidt
- Fix incorrect event codes in power9-event-list from Madhavan Srinivasan
- Move register_process_table() out of ppc_md from Michael Ellerman
Use jump_label for [cpu|mmu]_has_feature() from Aneesh Kumar K.V, Kevin Hao and Michael Ellerman:
- Add mmu_early_init_devtree() from Michael Ellerman
- Move disable_radix handling into mmu_early_init_devtree() from Michael Ellerman
- Do hash device tree scanning earlier from Michael Ellerman
- Do radix device tree scanning earlier from Michael Ellerman
- Do feature patching before MMU init from Michael Ellerman
- Check features don't change after patching from Michael Ellerman
- Make MMU_FTR_RADIX a MMU family feature from Aneesh Kumar K.V
- Convert mmu_has_feature() to returning bool from Michael Ellerman
- Convert cpu_has_feature() to returning bool from Michael Ellerman
- Define radix_enabled() in one place & use static inline from Michael Ellerman
- Add early_[cpu|mmu]_has_feature() from Michael Ellerman
- Convert early cpu/mmu feature check to use the new helpers from Aneesh Kumar K.V
- jump_label: Make it possible for arches to invoke jump_label_init() earlier from Kevin Hao
- Call jump_label_init() in apply_feature_fixups() from Aneesh Kumar K.V
- Remove mfvtb() from Kevin Hao
- Move cpu_has_feature() to a separate file from Kevin Hao
- Add kconfig option to use jump labels for cpu/mmu_has_feature() from Michael Ellerman
- Add option to use jump label for cpu_has_feature() from Kevin Hao
- Add option to use jump label for mmu_has_feature() from Kevin Hao
- Catch usage of cpu/mmu_has_feature() before jump label init from Aneesh Kumar K.V
- Annotate jump label assembly from Michael Ellerman
TLB flush enhancements from Aneesh Kumar K.V:
- radix: Implement tlb mmu gather flush efficiently
- Add helper for finding SLBE LLP encoding
- Use hugetlb flush functions
- Drop multiple definition of mm_is_core_local
- radix: Add tlb flush of THP ptes
- radix: Rename function and drop unused arg
- radix/hugetlb: Add helper for finding page size
- hugetlb: Add flush_hugetlb_tlb_range
- remove flush_tlb_page_nohash
Add new ptrace regsets from Anshuman Khandual and Simon Guo:
- elf: Add powerpc specific core note sections
- Add the function flush_tmregs_to_thread
- Enable in transaction NT_PRFPREG ptrace requests
- Enable in transaction NT_PPC_VMX ptrace requests
- Enable in transaction NT_PPC_VSX ptrace requests
- Adapt gpr32_get, gpr32_set functions for transaction
- Enable support for NT_PPC_CGPR
- Enable support for NT_PPC_CFPR
- Enable support for NT_PPC_CVMX
- Enable support for NT_PPC_CVSX
- Enable support for TM SPR state
- Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
- Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
- Enable support for EBB registers
- Enable support for Performance Monitor registers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Q8E
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"These were delayed for various reasons, so I let them sit in next a
bit longer, rather than including them in my first pull request.
Fixes:
- Fix early access to cpu_spec relocation from Benjamin Herrenschmidt
- Fix incorrect event codes in power9-event-list from Madhavan Srinivasan
- Move register_process_table() out of ppc_md from Michael Ellerman
Use jump_label use for [cpu|mmu]_has_feature():
- Add mmu_early_init_devtree() from Michael Ellerman
- Move disable_radix handling into mmu_early_init_devtree() from Michael Ellerman
- Do hash device tree scanning earlier from Michael Ellerman
- Do radix device tree scanning earlier from Michael Ellerman
- Do feature patching before MMU init from Michael Ellerman
- Check features don't change after patching from Michael Ellerman
- Make MMU_FTR_RADIX a MMU family feature from Aneesh Kumar K.V
- Convert mmu_has_feature() to returning bool from Michael Ellerman
- Convert cpu_has_feature() to returning bool from Michael Ellerman
- Define radix_enabled() in one place & use static inline from Michael Ellerman
- Add early_[cpu|mmu]_has_feature() from Michael Ellerman
- Convert early cpu/mmu feature check to use the new helpers from Aneesh Kumar K.V
- jump_label: Make it possible for arches to invoke jump_label_init() earlier from Kevin Hao
- Call jump_label_init() in apply_feature_fixups() from Aneesh Kumar K.V
- Remove mfvtb() from Kevin Hao
- Move cpu_has_feature() to a separate file from Kevin Hao
- Add kconfig option to use jump labels for cpu/mmu_has_feature() from Michael Ellerman
- Add option to use jump label for cpu_has_feature() from Kevin Hao
- Add option to use jump label for mmu_has_feature() from Kevin Hao
- Catch usage of cpu/mmu_has_feature() before jump label init from Aneesh Kumar K.V
- Annotate jump label assembly from Michael Ellerman
TLB flush enhancements from Aneesh Kumar K.V:
- radix: Implement tlb mmu gather flush efficiently
- Add helper for finding SLBE LLP encoding
- Use hugetlb flush functions
- Drop multiple definition of mm_is_core_local
- radix: Add tlb flush of THP ptes
- radix: Rename function and drop unused arg
- radix/hugetlb: Add helper for finding page size
- hugetlb: Add flush_hugetlb_tlb_range
- remove flush_tlb_page_nohash
Add new ptrace regsets from Anshuman Khandual and Simon Guo:
- elf: Add powerpc specific core note sections
- Add the function flush_tmregs_to_thread
- Enable in transaction NT_PRFPREG ptrace requests
- Enable in transaction NT_PPC_VMX ptrace requests
- Enable in transaction NT_PPC_VSX ptrace requests
- Adapt gpr32_get, gpr32_set functions for transaction
- Enable support for NT_PPC_CGPR
- Enable support for NT_PPC_CFPR
- Enable support for NT_PPC_CVMX
- Enable support for NT_PPC_CVSX
- Enable support for TM SPR state
- Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
- Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
- Enable support for EBB registers
- Enable support for Performance Monitor registers"
* tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (48 commits)
powerpc/mm: Move register_process_table() out of ppc_md
powerpc/perf: Fix incorrect event codes in power9-event-list
powerpc/32: Fix early access to cpu_spec relocation
powerpc/ptrace: Enable support for Performance Monitor registers
powerpc/ptrace: Enable support for EBB registers
powerpc/ptrace: Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
powerpc/ptrace: Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
powerpc/ptrace: Enable support for TM SPR state
powerpc/ptrace: Enable support for NT_PPC_CVSX
powerpc/ptrace: Enable support for NT_PPC_CVMX
powerpc/ptrace: Enable support for NT_PPC_CFPR
powerpc/ptrace: Enable support for NT_PPC_CGPR
powerpc/ptrace: Adapt gpr32_get, gpr32_set functions for transaction
powerpc/ptrace: Enable in transaction NT_PPC_VSX ptrace requests
powerpc/ptrace: Enable in transaction NT_PPC_VMX ptrace requests
powerpc/ptrace: Enable in transaction NT_PRFPREG ptrace requests
powerpc/process: Add the function flush_tmregs_to_thread
elf: Add powerpc specific core note sections
powerpc/mm: remove flush_tlb_page_nohash
powerpc/mm/hugetlb: Add flush_hugetlb_tlb_range
...
Just a few minor fixes:
- Fix another incorrect inline asm register constraint, which has been
lying quietly for 5 and a half years before finally causing build
breakage during this merge window.
- Removal of duplicated KERN_INFO from Joe Perches.
- Typo fixes from Andrea Gelmini.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8ih8
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag architecture updates from James Hogan:
"Just a few minor fixes:
- Fix another incorrect inline asm register constraint, which has
been lying quietly for 5 and a half years before finally causing
build breakage during this merge window.
- Removal of duplicated KERN_INFO from Joe Perches
- Typo fixes from Andrea Gelmini"
* tag 'metag-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Fix __cmpxchg_u32 asm constraint for CMP
metag: Remove duplicate KERN_<LEVEL> prefix
metag: Fix typos
This defconfig is intended not to be specific to a particular board;
it enables drivers for all currently-supported hardware, and should be
updated to include additional drivers as they are added.
Signed-off-by: Rich Felker <dalias@libc.org>
Enable common clk framework for DT-based boards and disable code that
depends on the legacy sh clk framework when common clk is enabled.
Once legacy drivers are converted over, the old code can be removed
entirely.
Signed-off-by: Rich Felker <dalias@libc.org>
The mempool_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Rich Felker <dalias@libc.org>
Support is hooked up via a cpu start method specified in the device
tree, and also depends on DT nodes that describe the interfaces for
performing IPI and identifying which cpu execution is taking place on.
The currently used method is a form of spin table, where secondary
cpus are unblocked by writing to a special address.
Signed-off-by: Rich Felker <dalias@libc.org>
The SH2 version of entry.S uses global variables, which need to be
cpu-local in order to work with SMP. For ease of access from asm,
simply use arrays indexed by cpu number, and require the availability
of an address (mmio register or properly setup per-cpu memory) from
which the current cpu's index can be read.
Signed-off-by: Rich Felker <dalias@libc.org>
The version of futex.h in asm-generic should really be adapted to do
the same thing so that this hideous code does not have to be
duplicated per-arch.
Signed-off-by: Rich Felker <dalias@libc.org>
The J-Core cpu has, as an ISA extension, an atomic compare-and-swap
instruction cas.l which applications need to use (instead the imask or
gusa atomic models, which are fundamentally limited to UP) for
synchronization in order to be compatible with SMP systems. Provide a
hwcap flag so that it's possible to do runtime selection and support
both.
Signed-off-by: Rich Felker <dalias@libc.org>
At the CPU/ISA level, the J2 is compatible with SH-2, and thus the
changes to add J2 support build on existing SH-2 support. However, J2
does not duplicate the memory-mapped SH-2 features like the cache
interface. Instead, the cache interfaces is described in the device
tree, and new code is added to be able to access the flat device tree
at early boot before it is unflattened.
Support is also added for receiving interrupts on trap numbers in the
range 16 to 31, since the J-Core aic1 interrupt controller generates
these traps. This range was unused but nominally for hardware
exceptions on SH-2, and a few values in this range were used for
exceptions on SH-2A, but SH-2A has its own version of the relevant
code.
No individual cpu subtypes are added for J2 since the intent moving
forward is to represent SoCs with device tree rather than as
hard-coded subtypes in the kernel. The CPU_SUBTYPE_J2 Kconfig item
exists only to fit into the existing cpu selection mechanism until it
is overhauled.
Signed-off-by: Rich Felker <dalias@libc.org>
Merge misc fixes from Andrew Morton:
"A few late-breaking fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/memblock.c: fix NULL dereference error
MAINTAINERS: update cgroup's document path
slub: drop bogus inline for fixup_red_left()
powerpc/fsl_rio: fix a missing error code
mm: initialise per_cpu_nodestats for all online pgdats at boot
mm/memblock: fix a typo in a comment
mm: disable CONFIG_MEMORY_HOTPLUG when KASAN is enabled
We should set the error code here rather than incorrectly returning 0.
Otherwise static checkers complain.
Link: http://lkml.kernel.org/r/20160804053525.GM775@mwanda
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull UML updates from Richard Weinberger:
"Beside of various fixes this also contains patches to enable features
such was Kcov, kmemleak and TRACE_IRQFLAGS_SUPPORT on UML"
* 'for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
hostfs: Freeing an ERR_PTR in hostfs_fill_sb_common()
um: Support kcov
um: Enable TRACE_IRQFLAGS_SUPPORT
um: Use asm-generic/irqflags.h
um: Fix possible deadlock in sig_handler_common()
um: Select HAVE_DEBUG_KMEMLEAK
um: Setup physical memory in setup_arch()
um: Eliminate null test after alloc_bootmem
Pull parisc updates from Helge Deller:
- added an optimized hash implementation for parisc (George Spelvin)
- C99 style cleanups in iomap.c (Amitoj Kaur Chawla)
- added breaks to switch statement in PDC function (noticed by Dan
Carpenter)
* 'parisc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Change structure intialisation to C99 style in iomap.c
parisc: Add break statements to pdc_pat_io_pci_cfg_read()
parisc: Add <asm/hash.h>
Pull m68knommu updates from Greg Ungerer:
"This series is all about Nicolas flat format support for MMU systems.
Traditional m68k no-MMU flat format binaries can now be run on m68k
MMU enabled systems too. The series includes some nice cleanups of
the binfmt_flat code and converts it to using proper user space
accessor functions.
With all this in place you can boot and run a complete no-MMU flat
format based user space on an MMU enabled system"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: enable binfmt_flat on systems with an MMU
binfmt_flat: allow compressed flat binary format to work on MMU systems
binfmt_flat: add MMU-specific support
binfmt_flat: update libraries' data segment pointer with userspace accessors
binfmt_flat: use clear_user() rather than memset() to clear .bss
binfmt_flat: use proper user space accessors with old relocs code
binfmt_flat: use proper user space accessors with relocs processing code
binfmt_flat: clean up create_flat_tables() and stack accesses
binfmt_flat: use generic transfer_args_to_stack()
elf_fdpic_transfer_args_to_stack(): make it generic
binfmt_flat: prevent kernel dammage from corrupted executable headers
binfmt_flat: convert printk invocations to their modern form
binfmt_flat: assorted cleanups
m68k: use same start_thread() on MMU and no-MMU
m68k: fix file path comment
m68k: fix bFLT executable running on MMU enabled systems
The LNKGET based atomic sequence in __cmpxchg_u32 has slightly incorrect
constraints for the return value which under certain circumstances can
allow an address unit register to be used as the first operand of a CMP
instruction. This isn't a valid instruction however as the encodings
only allow a data unit to be specified. This would result in an
assembler error like the following:
Error: failed to assemble instruction: "CMP A0.2,D0Ar6"
Fix by changing the constraint from "=&da" (assigned, early clobbered,
data or address unit register) to "=&d" (data unit register only).
The constraint for the second operand, "bd" (an op2 register where op1
is a data unit register and the instruction supports O2R) is already
correct assuming the first operand is a data unit register.
Other cases of CMP in inline asm have had their constraints checked, and
appear to all be fine.
Fixes: 6006c0d8ce ("metag: Atomics, locks and bitops")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-metag@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.9.x-
The jump table can reference text found in an __exit section. Thus,
instead of discarding it at build time, include EXIT_TEXT as part of
__init and it will be released when the system boots.
Link: http://lkml.kernel.org/r/60284113bb759121e8ae3e99af1535647e52123f.1467837322.git.jbaron@akamai.com
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously, all the __exit sections were just dropped by the link phase.
However, if there are static_key (jump label) constructs in __exit
sections that are not modules, the link fails with the message:
`.exit.text' referenced in section `__jump_table' of xxx.o:
defined in discarded section `.exit.text' of xxx.o
Support this usage by keeping the .exit.text sections in the final image
if JUMP_LABEL is defined, then discarding them once initialization is
complete.
Link: http://lkml.kernel.org/r/bfd7c107c610c30e992868ebfe2a5d796a097464.1467837322.git.jbaron@akamai.com
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The jump table can reference text found in an __exit section. Thus,
instead of discarding it at build/link time, include EXIT_TEXT as part
of __init and release it at system boot time.
Without this patch the link fails with:
`.exit.text' referenced in section `__jump_table' of xxx.o:
defined in discarded section `.exit.text' of xxx.o
Link: http://lkml.kernel.org/r/d822da427ab07a02a394602eca687104ff682f83.1467837322.git.jbaron@akamai.com
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The stringify_in_c() macro may not be included. Make the dependency
explicit.
Link: http://lkml.kernel.org/r/564720c5328edd53c9d56db325be7215440eec3e.1467837322.git.jbaron@akamai.com
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Joe Perches <joe@perches.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set_pte_at(.) will set or unset the PTE_RDONLY hardware bit before
writing the entry to the table.
This can cause problems with the copy-on-write logic in hugetlb_cow:
*) hugetlb_cow(.) called to handle a write fault on read only pte,
*) Before the copy-on-write updates the new page table a call is
made to pte_same(huge_ptep_get(ptep), pte)), to check for a race,
*) Because set_pte_at(.) changed the pte, *ptep != pte, and the
hugetlb_cow(.) code erroneously assumes that it lost the race,
*) The new page is subsequently freed without being used.
On arm64 this problem only becomes apparent when we apply:
67961f9 mm/hugetlb: fix huge page reserve accounting for private
mappings
When one runs the libhugetlbfs test suite, there are allocation errors
and hugetlbfs pages become erroneously locked in memory as reserved.
(There is a high HugePages_Rsvd: count).
In this patch we introduce pte_same which ignores the PTE_RDONLY bit,
allowing for the libhugetlbfs test suite to pass as expected and
without leaking any reserved HugeTLB pages.
Reported-by: Huang Shijie <shijie.huang@arm.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 4b85507860 ("KVM: nVMX: Don't advertise single
context invalidation for invept") removed advertising
single context invalidation since the spec does not mandate it.
However, some hypervisors (such as ESX) require it to be present
before willing to use ept in a nested environment. Advertise it
and fallback to the global case.
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nested vpid is already supported and both single/global
modes are advertised to the guest
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Includes GSI routing support to go along with the new VGIC and a small fix that
has been cooking in -next for a while.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXoydqAAoJEEtpOizt6ddyM3oH/1A4VeG/J9q4fBPXqY2tVWXs
c3P7UgNcrEgUNs/F9ykQY/lb31deecUzaBt1OyTf+RlsNbihq3dQdYcBhxtUODw/
Faok582ya3UFgLW+IRHcID0EbkVOpIzMhOStYsnU/Dz7HG1JL9HdPzwkid7iu9LT
fI6yrrBnJFjdWAAQ4BkcEKBENRsY8NTs7jX5vnFA92MkUBby7BmariPDD3FtrB+f
Ob9B7CxM30pNqsN7OA/QvFOHMJHxf3s1TBKwmPHe5TLIfSzV1YxcEGiMc0lWqF4v
BT8ZeMGCtjDw94tND1DskfQQRPaMqPmGuRTrAW/IuE2n92bFtbqIqs7Cbw0fzLE=
=Vm6Q
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.8-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.8 - Take 2
Includes GSI routing support to go along with the new VGIC and a small fix that
has been cooking in -next for a while.
The new simplified __pvclock_read_cycles does the same computation
as vread_pvclock, except that (because it takes the pvclock_vcpu_time_info
pointer) it has to be moved inside the loop. Since the loop is expected to
never roll, this makes no difference.
Acked-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The version field in struct pvclock_vcpu_time_info basically implements
a seqcount. Wrap it with the usual read_begin and read_retry functions,
and use these APIs instead of peppering the code with smp_rmb()s.
While at it, change it to the more pedantically correct virt_rmb().
With this change, __pvclock_read_cycles can be simplified noticeably.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We want to initialise register_process_table() before ppc_md is setup,
so that it can be called as part of MMU init (at least on Radix ATM).
That no longer works because probe_machine() requires that ppc_md be
empty before it's called, and we now do probe_machine() much later.
So make register_process_table a global for now. It will probably move
into a mmu_radix_ops struct at some point in the future.
This was broken by me when applying commit 7025776ed1 "powerpc/mm:
Move hash table ops to a separate structure" due to conflicts with other
patches.
Fixes: 7025776ed1 ("powerpc/mm: Move hash table ops to a separate structure")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These have been changed in the hardware, update Linux's version.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds support for kcov to UML.
There is a small problem where UML will randomly segfault during boot;
this is because current_thread_info() occasionally returns an invalid
(non-NULL) pointer and we try to dereference it in
__sanitizer_cov_trace_pc(). I consider this a bug in UML itself and this
patch merely exposes it.
[v2: disable instrumentation in UML-specific code]
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Meyer <thomas@m3y3r.de>
Cc: user-mode-linux-devel <user-mode-linux-devel@lists.sourceforge.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
