Convert the calls that write the i2c clock register over to the new
em28xx_write_reg() function that allows for or'ing bits
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce a new function that writes to a single register. This is
useful because the vast majority of register writes are a single
register, and this format permits or'ing register value bits together.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Please accept this patch to refer to my new email address
Signed-off-by: Jelle Foks <jelle@foks.us>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
AC97 devices provide several input and outputs. However, before this
patch, em28xx device weren't properly allowing the usage of ac97
possible combinations. Also, several input volumes were left untouched,
instead of making sure that the volumes were set on mute state.
This patch improves support for ac97 devices by allowing to use any
inputs, and making sure that unused inputs are set on mute state.
Yet, some work is still needed to select the AC97 output.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes easier to identify vendor ID, since AC97 vendors are
generally identified by 3 bytes. The remaining byte is used by the
vendor to identify its devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch properly implements audio handling on em28xx. Before this
patch, it was assumed that every device has an Empia 202 audio chip.
However, this is not true.
After this patch, specific AC97 chipset setup and configurations can be
done.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
audio mux entries were described by 0 and 1 magic numers. Use an enum
alias for each entry type.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make use of the em28xx chip configuration register to determine whether
we have AC97 audio, I2S audio, or no audio support at all.
Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Previously, AC97 registers were named as if they were part of em28xx
device, generating some confusion. Replace such names for a more general
naming convention.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@i@
@@
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(E[...]))
+ ARRAY_SIZE(E)
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(T))
+ ARRAY_SIZE(E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All noticed by sparse:
drivers/media/dvb/dvb-usb/cinergyT2-core.c:35:5: warning: symbol 'disable_remote' was not declared. Should it be static?
drivers/media/dvb/dvb-usb/cinergyT2-core.c:48:23: warning: symbol 'cinergyt2_usb_device' was not declared. Should it be static?
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:160:15: warning: cast to restricted __le16
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:190:9: warning: cast to restricted __le32
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:208:9: warning: cast to restricted __le32
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:227:24: warning: cast to restricted __le16
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:275:12: warning: incorrect type in assignment (different base types)
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:275:12: expected unsigned short [unsigned] [assigned] [usertype] tps
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:275:12: got restricted __le16 [usertype] <noident>
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:276:13: warning: incorrect type in assignment (different base types)
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:276:13: expected unsigned int [unsigned] [assigned] [usertype] freq
drivers/media/dvb/dvb-usb/cinergyT2-fe.c:276:13: got restricted __le32 [usertype] <noident>
Cc: Thierry Merle <thierry.merle@free.fr>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Place the s5h1411 into low power mode until first use (to handle the case where
the user plugs in the device and then doesn't use it for a while). On the
Pinnacle 801e, this brings the power usage from 126ma down to 82ma.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the ATI TV Wonder HD 600 USB Remote Control
(required a new keymap)
[mchehab@redhat.com: Fix CodingStyle]
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refactor the em28xx IR support based on the em2860/em2880 and em2874
datasheets.
Tested on the HVR-950 (em2883), Pinnacle 800e (em2883), Pinnacle 80e (em2874)
using the remote controls that came with those products.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The first em28xx were based on i2c IR's. However, some newer designs
are coming with a polling-based IR. Those are done by reading a register
set at em28xx.
This patch adds core polling support for those devices. Later patches will
add support for some device-specific IR's.
This patch adds the same basic IR polling code used by bttv, cx88 and saa7134, and
shares the common getkey masks defined at ir-common.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add registration for Pinnacle 80e ATSC tuner
Register the em2874 based Pinnacle 80e device. Note that support for this
device also requires the new drx-j driver (which is not available yet)
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Thanks to Joerg Schindler from Pinnacle for providing sample hardware.
Thanks to Rainer Miethling from Pinnacle for providing engineering support.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly support capture start on em2874
The transport stream enable register moved in the em2874, so make it work
properly.
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the logic so that the em28xx-alsa module does not get loaded for devices
that don't support analog audio (such as the em2874)
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Empia moved around their endpoint configuration in newer chips, so accommodate
the changes
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix case where we could end up dereferencing a NULL pointer if dev->vdev or
dev->vbi_dev were not set properly.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Empia switched to a 16-bit addressable eeprom in newer devices. While we
could certainly write a routine to read the eeprom, there is nothing of use
in there that cannot be accessed through registers, and there is the risk that
we could corrupt the eeprom (since a 16-bit read call is interpreted as a
write call by 8-bit eeproms). So just be safe and bail out of the function.
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Empia moved the location of the GPIO/GPO registers in newer devices. Add the
ability to specify the relocated registers (including caching of register
contents).
Thanks for Ray Lu from Empia for providing the em2874 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When setting up the device, remember the chip id, so we can control behavior
in the future without having to read the register continuously.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a EM28XX_NODECODER option to the list of available decoders. This option
becomes important for devices that do not have analog support.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add em2874 chip id
Add chip id for em2874 to list of known chips
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_ioctl2 lacks implementation of those two ioctls:
- VIDIOC_ENUM_FRAMESIZES and VIDIOC_ENUM_FRAMEINTERVALS
Adds implementation for those.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cleans-up MFE attachment for saa-7134 dvb
devices.
note: MFE is not fully implemented here yet.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This cleans-up MFE attachment for these cards plus
two cases of potential memory leak on attachment
failure.
Signed-off-by: Darron Broad <darron@kewl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Failed requests will now generate a one-time warning message instead of the
usual "Failed to query..." error, which should be more user-friendly. The
driver will also recover automatically from failed GET_MIN/GET_MAX requests
when the device is half-broken without requiring the MINMAX quirk (fully
broken devices still need the quirk).
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to http://bugzilla.kernel.org/show_bug.cgi?id=11997,
the driver sn9c102 does not work for this webcam.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to http://bugzilla.kernel.org/show_bug.cgi?id=11920,
the driver sn9c102 does not work for this webcam.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for suspend and resume methods in driver.
Without this kradio and gnomeradio crashes during resume.
Also .supports_autosuspend in usb_driver struct set equal to 0 to avoid
suspending of module if usb_autosuspend enabled.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The UVC specification does not require frame descriptors to be sorted by
bFrameIndex. At least one camera (145f:013e) is known not to sort the
descriptors properly, so they need to be sorted during parsing as the driver
then accesses them by index.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
